HP D2842W, D2842A User Manual

HP D2842A

HP D2842W

HP 90

19-inch Color Monitors
18-inch Viewable Image

User’s Guide

*

19-Zoll-Farbbildschirme

18 Zoll Bildanzeige

Benutzerhandbuch

Moniteurs couleur 19 pouces

Affichage 18 pouces

Guide de l’utilisateur

Pantallas de color de 19 pulgadas

18 pulgadas de imagen visualizada

Manual del Usuario Léase esto primero

Video a colori da 19 pollici
18 effettivi per l’immagine

Manuale utente

Monitor Colorido de 19 polegadas

Imagem Visível de 18 polegadas

Guia do Usuário

Notice

The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett­Packard.
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document
may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company.

Hinweis

Inhaltliche Änderungen vorbehalten.
Hewlett-Packard übernimmt keine Garantie welcher Art auch immer für diese Ausrüstung, einschließlich der (doch nicht begrenzt
auf die) Qualitätsgarantie und die Garantie bezüglich Eignung für einen bestimmten Zweck.
Hewlett-Packard haftet nicht für in dieser Dokumentation enthaltene Fehler oder für unbeabsichtigte oder indirekte Schäden in
Verbindung mit der Lieferung, der Leistung oder der Benutzung der Ausrüstung.
Hewlett-Packard übernimmt keine Haftung fur den Betrieb oder die Zuverlässigkeit seiner Software, wenn diese auf Hardware
benutzt wird, die nicht von Hewlett-Packard geliefert wurde.
Dieses Dokument enthalt proprietäre Informationen, die durch das Copyright geschützt sind. Alle Rechte vorbehalten. Dieses
Dokument darf ohne vorherige schriftliche Genehmigung der Hewlett-Packard Company weder ganz noch teilweise fotokopiert,
reproduziert oder übersetzt werden.

Avertissement

Les informations contenues dans ce document peuvent être modifiées sans préavis.
Hewlett-Packard ne donne aucune garantie de quelque sorte que ce soit concernant, sans que ce soit limitatif, les garanties
implicites de qualité commerciale de ce matériel, ou la bonne adaptation de celui-ci à un usage particulier.
Hewlett-Packard n’est pas responsable des erreurs pouvant apparaître dans ce manuel et n’est pas non plus responsable des
dommages directs ou indirects résultant de l’équipement, des performances et de l’utilisation de ce matériel.
Hewlett-Packard ne saurait être tenu pour responsable de l’utilisation et de la fiabilité de son logiciel sur des matériels non fournis
par Hewlett-Packard.
Les informations contenues dans ce document sont originales et protégées par copyright. Tous droits réservés. L’acheteur s’interdit
en conséquence de les photocopier, de les reproduire ou de les traduire dans toute autre langue, sauf accord préalable et écrit de
Hewlett-Packard.

Aviso

La información contenida en este documento está sujeta a cambios sin previo aviso.
Hewlett-Packard no ofrece ningún tipo de garantía con respecto a este material, incluyendo, pero sin limitarse a, las garantías
implícitas de comerciabilidad e idoneidad para un fin determinado.
Hewlett-Packard no asume responsabilidad alguna por los posibles errores contenidos o por los daños casuales o emergentes
relacionados con el suministro, funcionamiento o uso de este material.
Hewlett-Packard no asume responsabilidad alguna por el uso o fiabilidad de su software en equipos que no hayan sido fabricados
por Hewlett-Packard.
Este documento contiene información patentada, protegida por las leyes del copyright. Reservados todos los derechos. Ninguna
parte de este documento puede ser fotocopiada, reproducida o traducida a otro idioma sin la autorización previa y por escrito de
Hewlett-Packard Company.

Avviso

Le informazioni contenute in questo documento sono soggette a cambiamento senza preavviso.
Hewlett-Packard non rilascia garanzie di alcun tipo riguardo a questo materiale, comprese le garanzie implicite di commerciabilità
e di idoneità per uno scopo particolare.
Hewlett-Packard non sarà ritenuta responsabile per errori contenuti in questo documento, né per danni accidentali o conseguenti
alla fornitura, alle prestazioni o all’uso di questo materiale.
Hewlett-Packard non si assume alcuna responsabilità riguardo all’uso o all’affidabilità del proprio software su apparecchiature di
altri produttori.
Questo documento contiene informazioni di proprietà protette da copyright. Tutti i diritti sono riservati. Nessuna parte di questo
documento può essere fotocopiata, riprodotta o tradotta in un’altra lingua senza un precedente consenso scritto di Hewlett-Packard
Company.

Nota

As informações contidas neste documento estão sujeitas a alteração sem notificação prévia.
A Hewlett-Packard não oferece nenhum tipo de garantia com relação a este material, incluindo, mas não limitada às, garantias
implícitas de comercialização e conveniência para um propósito específico.
A Hewlett-Packard não será responsável por erros aqui contidos ou por danos incidentais ou conseqüenciais relacionados ao
fornecimento, desempenho ou utilização deste material.
A Hewlett-Packard não se responsabiliza pelo uso ou confiabilidade se seu software em equipamentos que não sejam fornecidos
pela Hewlett-Packard.
Este documento contém informações proprietárias protegidas por direitos autorais. Todos os direitos são reservados. Nenhuma
parte deste documento pode ser fotocopiada, reproduzida ou traduzida para outro idioma sem o consentimento prévio por escrito
da Hewlett-Packard Company

Hewlett-Packard France 38053 Grenoble Cedex 9 France© 1998 Hewlett-Packard
Company

Francais

1

Full scan screen that gives an
edge to edge image

0.26 mm dot pitch for excellent
graphics

Anti-glare, anti-static, multilayer
screen coating

Image adjustment controls to
operate on-screen display menus

Contrast/Brightness
Controls

HP D2842A, HP D2842W
HP 90
19-inch Color Monitor
18-inch Viewable Image
User’s Guide

On/Off switch

Status indicator

HP 19” Color Monitor User’s Guide

Important Safety Instructions

Important Safety Instructions

Before you plug in your new monitor, read these important safety instructions.

WARNING Connect the monitor only to a grounded power outlet. Use the power cord

supplied with the monitor or one with a properly grounded plug. Ensure the
cable meets your country’s standards for safety.

To completely disconnect power at the monitor, remove the power cord from
the power outlet. Ensure that the power outlet is easily accessible.

The monitor is quite heavy (the weight is shown in the technical
specifications). We recommend you ask the assistance of a second person
when lifting or moving it.

CAUTION To reduce the risk of electric shock, do not remove cover (or back). No user

serviceable parts inside. Refer servicing to qualified service personnel.

The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the

!

user to the presence of important operating and servicing instructions in the
literature accompanying the appliance.

USA and Canada

If the power cord is not supplied with your monitor, select the proper power
cord according to your national electric safety codes.

• USA: use a UL Listed detachable power cord, type SVT.

• Canada: use a CSA certified detachable power cord.

Si le cordon secteur n’est pas livré avec votre moniteur, utiliser un cordon
secteur en accord avec votre code électrique national.

• USA: utiliser un cordon secteur UL Listé, de type SVT.

• Canada: utiliser un cordon secteur certifié CSA.

2 English

HP 19” Color Monitor User’s Guide

What Your New Monitor Offers

What Your New Monitor Offers

Your HP monitor is a 19-inch (18-inch viewable image), high resolution,
multi-synchronous color monitor. Multi-synchronous means that the monitor
supports a range of video modes. It is optimized to be used with all
Hewlett-Packard computers.

Your HP color monitor has the following features:

• A 19-inch flat square tube, with a 18-inch viewable image, and

0.26 mm dot pitch for excellent graphics. Anti-glare, multilayer coating to
minimize reflection.

• Support of video modes up to 1280 ×1024 at 85 Hz refresh rate, and up to
1600 ×1200 using a 75 Hz refresh rate.

• Image adjustment using on-screen display menus. Includes color
adjustment and image manipulation controls to optimize the quality and
position of the image.

1

• Monitor power management system (VESA
suitably equipped HP computers to automatically reduce the power
consumption of the monitor. Complies with the Energy Star Computers
Program initiated by the US EPA

2

specification for energy efficient
monitors. As an Energy Star Partner, Hewlett Packard has determined that
this product meets the Energy Star guidelines for energy efficiency.

standard) controlled from

3

• Monitor Plug and Play capability (VESA DDC2B standard) that enables the
monitor to identify itself to suitably equipped HP computers.

• Compliance with ISO 9241-3/8 and ZH-1/618 ergonomic standards.

• This monitor complies to TCO 99 requirements. (Refer to “TCO 99 ­Ecology Energy Emissions Ergonomics“ on page 23)

• Your HP monitor complies with MPRII guidelines for upper limits of
electrical and electrostatic emissions, from the Swedish National Board
Measurements and Testing.

• Your HP monitor complies with the Swedish Standard SS4361490,
level B, (MPRIII) for electric and magnetic field emission.

• Your HP monitor complies with the Blue Angel and E2000 environmental
requirements.

1. VESA is the Video Electronics Standards Association

2. The US EPA is the United States Environmental Protection Agency

3. ENERGY STAR is a US registered service mark of the US EPA.

English 3

HP 19” Color Monitor User’s Guide

Setting Up Your Monitor

Setting Up Your Monitor

Where to Place the Monitor

Place your monitor on a flat sturdy surface.

Ensure the operating site is free from excessive heat, moisture, dust and
sources of electromagnetic fields. Sources of electromagnetic fields include
transformers, motors, and other monitors.

Avoid exposing the monitor to direct sunlight.

Connecting the Cables

NOTE Before you connect any cables, or install your HP monitor, refer to the safety

instructions at the beginning of the manual. Refer also to the user manual
which accompanies your PC and video adapter to ensure this equipment is
correctly installed.

1 Make sure your computer and monitor are switched off.

2 Connect the video cable (it has a 15-pin plug) to the video outlet on your

computer and to the video outlet on the rear of your monitor. Tighten the
thumbscrews on the plug.

3 Connect the power cord to the monitor.
4 Plug the power cord into a grounded power outlet.

1 PC and Monitor OFF

3

Power Cords

2

Video cable

4

NOTE The location of your computer’s video outlet may be different to the one shown

in the diagram. Refer to the manual that came with your computer, if
necessary.

4 English

HP 19” Color Monitor User’s Guide

Using Your Monitor

Using Your Monitor

The on/off switch is on the front of the monitor.

Contrast and brightness can be adjusted directly.

Use the controls underneath the front panel of the monitor to obtain the
required adjustment.

Button

and

adjustment controls

Button

On/Off switch

Status Indicator
Contrast Control
Brightness Control

OSD

BASIC ADJUSTMENTS

91.1kHz/85Hz

ENTER:

ETC

Main Menu

SEL:

You can adjust the size, position, shape and quality of the displayed image using
the controls on the front of the monitor to operate the on-screen menus.

1 Press the button to activate the monitor’s on-screen main menu.

2 Use the and adjustment controls to select the sub-menu you require.
3 Press to make your selection.

Changing the Language of your On Screen Menu

Your on screen display operates in seven different languages: English,
Deutsch, Français, Espanõl, Italiano, Svenska and Suomi.

To change the language of your on screen menu:

1 Select and press to enter the LANGUAGE sub-menu.

2 Use the and adjustment controls to select the language you require.
3 Press to exit.

English 5

HP 19” Color Monitor User’s Guide

Using Your Monitor

Adjusting the Size and Position of the Displayed Image

To adjust the size and position of the displayed image:

1 Select and press to enter the

BASIC ADJUSTMENTS

sub-menu.

2 Select the feature you wish to modify using the and adjustment

controls, then press to confirm your selection.

OSD

BASIC ADJUSTMENTS

91.1kHz/85Hz

ENTER:

ENTER:

H POSITION

91.1kHz/85Hz

ETC

SEL:

SEL:

The following table lists the adjustment options available:

Adjustment Menu Item Use to Adjust

H POSITION The horizontal position of the displayed image.

H SIZE The horizontal size of the displayed image.

V POSITION The vertical position of the displayed image.

V SIZE The vertical size of the displayed image.

ZOOM The overall size of the displayed image.

TILT The displayed image if it appears to be rotated.

1. Depending on the orientation of your monitor, you may experience rotation of the image. This is due to
the influence of the earth’s magnetic field and is normal for all monitors.

1

3 Use the and adjustment controls to make your adjustments.
4 Press to exit.

NOTE To revert to the default position and size settings, select from this

sub-menu.

6 English

Adjusting the Shape the Displayed Image

To adjust the shape of the displayed image:

HP 19” Color Monitor User’s Guide

Using Your Monitor

1 Select and press to enter the

GEOMETRY

sub-menu.

2 Select the feature you wish to modify using the and adjustment

controls, then press to confirm your selection.

91.1kHz/85Hz

ENTER:

ENTER:

OSD

GEOMETRY

PINCUSHION

91.1kHz/85Hz

ETC

SEL:

SEL:

The following table lists the adjustment options available:

Adjustment Menu Item Use to Adjust the displayed image

PINCUSHION If the vertical edges appear to bow in or out.

TRAPEZOID If the vertical edges do not appear parallel.

PIN BALANCE If the vertical edges appear to bow to the left or right.

PARALLELOGRAM If the vertical edges appear to be tilted to the left or right.

PIN S ADJUST If the vertical edges appear to have an irregular distortion.

PIN W ADJUST If the vertical edges appear to have an irregular distortion.

3 Use the and adjustment controls to make your adjustments.
4 Press to exit.

NOTE To revert to the default shape settings of the displayed image, select from

this sub-menu.

English 7

HP 19” Color Monitor User’s Guide

Using Your Monitor

Improving the Image Quality

To improve the quality of the displayed image:

1 Select and press to enter the

IMAGE

sub-menu.

2 Select the feature you wish to modify using the and adjustment

controls, then press to confirm your selection.

91.1kHz/85Hz

ENTER:

ENTER:

OSD

IMAGE

H MOIRE

91.1kHz/85Hz

ETC

SEL:

SEL:

The following table lists the options available:

Adjustment Menu Item Use to

H MOIRE Reduce the effects of horizontal moire (horizontal screen ripple)

V MOIRE Reduce the effects of vertical moire (vertical screen ripple)

H CONVERGENCE Adjust the alignment of red and blue horizontal fields.

V CONVERGENCE Adjust the alignment of red and blue vertical fields.

PURITY Adjust the overall purity of the image if the color appears

uneven.

DEGAUSS Keep the monitor free from unwanted magnetism that can

result in color impurity.

1

It is recommended that you degauss at

least every week.

1. Degaussing is accompanied by brief instability of the displayed image and a slight humming sound.

3 Use the and adjustment controls to improve the quality of the image.
4 Press to exit.

8 English

HP 19” Color Monitor User’s Guide

Using Your Monitor

Adjusting the Color of the Displayed Image

Your monitor displays a combination of red, blue and green to show a full color
image. If you want to change the proportions of red, blue and green used by
your monitor you need to change the color temperature. To adjust the color of
the displayed image:

1 Select and press to enter the

COLOR sub-menu.

2 Select the feature you require using the and adjustment controls, then

press to confirm your selection

9300

80.2kHz/75Hz

ENTER:

ENTER:

OSD

COLOR

B

G

R

7200

K

COLOR TEMP

91.1kHz/85Hz

K

SEL:

ETC

CLAMP

SEL:

The following table explains the color adjustment options available:

Adjustment

Use to Action

Menu Item

9300K/7200K Select a Preset Color

Select 9300K or 7200K.

Temperature

B

G

R

USER Adjust the levels of red,

green and blue.

Press to confirm your selection, press
to select red, green and blue, then use the

and adjustment controls to adjust the color

level.

K

COLOR TEMP Select your own color

temperature.

Press to confirm your selection, then use
the and adjustment controls to select a
temperature.

CLAMP Enable SOG (Sync On

Green) when there is SOG
Video Signal input.

Press to confirm your selection, then use
the and adjustment controls to
enable/disable SOG.

3 Press to exit.

English 9

HP 19” Color Monitor User’s Guide

Using Your Monitor

Changing the OSD Setting

To adjust the position or timing of your on screen display menu:

1 Select and press to enter the

OSD

OSD ADJUST

sub-menu.

2 Select the feature you require using the and adjustment controls, then

press to confirm your selection.

OSD

80.2kHz/75Hz

ENTER:

ENTER:

OSD

OSD ADJUST

H POSITION

91.1kHz/85Hz

ETC

SEL:

SEL:

The following table lists the options available.

Adjustment Menu Item

Use to Adjust

H POSITION The horizontal position of the on screen menu.

V POSITION The vertical position of the on screen menu.

OSD TIME The duration that your on screen menu appears on screen.

3 Use the and adjustment controls to make the required adjustment to

the on screen menu.

4 Press to exit.

10 English

HP 19” Color Monitor User’s Guide

Using Your Monitor

Adjusting the Advanced Options

1 Select and press to enter the

ETC

MISCELLANEOUS

sub-menu.

2 Select the feature you require using the and adjustment controls,

then press to confirm your selection.

OSD

ETC

MISCELLANEOUS

ENTER:

i

80.2kHz/75Hz

ENTER:

DEGAUSS

91.1kHz/85Hz

ETC

DDC

SEL:

SEL:

The following table indicates the options available.

Adjustment Menu

Use To Action

Item

DEGAUSS (Refer to “Improving the Image Quality“ on page 8)

INFORMATION Obtain information on video

i

resolutions and refresh rates
supported by your monitor.

VIDEO LEVEL Set Video Solution to 0.7V or

1.0V.(For all HP computers

Press for information on User Settings.
Press for information on Preset
Settings

Select the Video Level using the and

adjustment controls.

select 0.7V)

DDC Enable or disable Plug and

Play capability (Refer to

Select ON or OFF using the and

adjustment controls.
Setting the Amount of
Displayed Information, on
page 12”).

1

2

.

1. Contains record of any adjustments that the user makes in the main menu system.

2. Standard configurations pre-loaded at the factory.

3 Press to exit.

English 11

HP 19” Color Monitor User’s Guide

Using Your Monitor

Setting the Amount of Displayed Information

To set the amount of displayed information, change the screen resolution of
your computer. The higher the screen resolution, the more information you
can see on the screen. It is recommended that you use a resolution of
1280×1024 at 85Hz. This gives easy-to-read characters, a large amount of
displayed information, and a flicker-free image.

You can make adjustments to the displayed image and they are automatically
saved for the resolution you are using. For example, if you adjust your monitor
when working in SVGA those settings are saved for SVGA. If you then work in
VGA and change the image settings, they are saved for VGA. The next time
you switch back to SVGA, your previous settings are used automatically.

To find out which resolutions and refresh rates are supported by your
monitor,refer to “What Video Modes are Supported” on page 14. To change
the screen resolution, please refer to the manual that came with your
computer or your operating system documentation, if necessary. To set the
image refresh rate (also known as the vertical frequency), refer to the
manual that came with your computer or your operating system.

Your monitor has a Plug and Play capability (VESA DDC2B standard) that
enables it to identify itself to suitably equipped HP computers. This will
automatically give you the best refresh rate for the resolution you have set.
Also, by using the appropriate software (when available), you can adjust the
monitor’s settings directly from your computer.

12 English

HP 19” Color Monitor User’s Guide

Using Your Monitor

Minimizing Eye Strain

To avoid screen flicker and minimize eye strain, use the highest supported
image refresh rate for the chosen resolution. It is recommended that you use
a refresh rate of 85 Hz. The image refresh rate is the number of times per
second that the image is refreshed.

Minimizing Energy Consumption

If your computer supports VESA monitor power management (available on
many HP computers), you can minimize the power consumed by the monitor.
There are two power saving modes:

1

• Suspend mode

(uses less than 8W). In this mode, the monitor’s front panel

indicator light is amber.

2

• Sleep mode

(uses less than 3W). In this mode, the monitor’s front panel

indicator light is amber.

To set these power saving modes, refer to the manual that came with your
computer. If your screen is not displaying an image, check the front panel
indicator light first — your monitor may be in a power saving mode.

1. Suspend mode is activated when horizontal sync is cut by the video controller.

2. Sleep mode is activated when both vertical and horizontal sync are cut by the video
controller.

English 13

HP 19” Color Monitor User’s Guide

What Video Modes are Supported

What Video Modes are Supported

Your monitor comes with the preset modes shown in the table below. It also
supports intermediate video modes. With the intermediate modes, the
displayed image may need to be optimized using the adjustment controls. All
modes are non-interlaced.

Screen Resolution Image Refresh Rate Video Solution

640×400 70 Hz VGA/DOS
640×480 75 Hz, 85 Hz Ergonomic VGA
800×600 75 Hz, 85 Hz Ergonomic Super VGA

1024×768 75 Hz, 85 Hz Ergonomic Ultra VGA 1024
1280×1024 75 Hz, 85 Hz Ultra VGA 1280
1600×1200 75 Hz Ultra VGA 1600

CAUTION Selecting a screen resolution/image refresh rate combination higher than

1600×1200 at 75Hz can damage your monitor.

Selecting a video mode not supported by your monitor will cause your monitor
screen to blank.

14 English

PICTURE TUBE

INPUT SIGNAL

INTERFACE

HP 19” Color Monitor User’s Guide

Technical Specifications

Technical Specifications

Size 19-inch flat screen/ 18-inch viewable image
Phosphorous Red, Green, Blue short persistence
Dot pitch 0.26 mm
Face Plate Anti-glare, multilayer coating
Video 0.7 Vp p analog RGB
Synchronization Separated H/V (TTL level), H/V mixed (TTL level), sync-on.

green

Input Connector 15-pin mini D-SUB

SCANNING FREQUENCY

MAX. RESOLUTION (H

WARM-UP TIME

PIXEL CLOCK

IMAGE SIZE

POWER SOURCE

OPERATING ENVIRONMENT

CABINET DIMENSIONS

NET WEIGHT

TILT/SWIVEL STAND

1. Use the standard image sizes to avoid distortion of the displayed image.

×

Horizontal 30 to 96 kHz
Vertical 50 to 200Hz
1600 ×1200 (75 Hz)

V)

30 minutes to reach optimum performance level

203 MHz

Standard size
Maximum size: 365(H) x 274(V) mm
AC 90 to 264 V, 47 to 63 Hz, 140W (max), less than 8W in Suspend mode, less than 3W in Sleep mode,

less than 3W when switched Off.
Temperature 10 °C to 40 °C (operating)

Humidity 10% RH through 80% RH (without condensation)
468(H) × 458(W) × 479(D) mm (with stand)

24,3 kg (53.57 lbs)

Tilt Angle - 5° to +13.5
Swivel Angle

1

:350(H) x 262(V) mm

- 20 °C to +60 °C (storage)

°

±45°

English 15

HP 19” Color Monitor User’s Guide

Care and Cleaning

Care and Cleaning

Do not place anything on top of the monitor. Doing so may block the monitor
vents and cause damage to the monitor due to overheating.

Do not let liquid get on or into the monitor.

To maximize screen life and prevent damage to the picture tube (such as
burned phosphor due to leaving the same image on the screen for a long
time), it is recommended that you:

• Use the monitor power management system (on HP PCs) or a screen saver
program.

• Avoid setting contrast and brightness to their maximum levels for
prolonged periods.

• If you do not have a power management system or a screen saver program,
switch the monitor off or reduce the brightness and contrast to minimum
levels when the monitor is not in use.

Your monitor has an anti-glare, anti-static screen coating. To prevent damage
to the monitor screen’s coating, use a regular household glass cleaner when
cleaning the screen. To clean the screen:

1 Switch the monitor off and remove the power plug (pull the plug, not the

cable).

2 Wet a soft cotton cloth with the cleaning solution and gently wipe the

screen. Do not spray cleaner onto the screen because the cleaner may drip
inside the monitor.

3 Dry with a clean, soft cotton cloth.

Do not use cleaning solutions containing fluoride, acids, or alkalis.

16 English

HP 19” Color Monitor User’s Guide

Environmental Information

Environmental Information

HP has a strong commitment toward the environment. Your HP monitor has
been designed to respect the environment as much as possible.

HP can also take back your old monitor for recycling when it reaches the end
of its useful life.

HP has a product take-back program in several countries. The collected
equipment is sent to one of HP’s recycling facilities in Europe or the USA. As
many parts as possible are reused. The remainder is recycled. Special care is
taken for batteries and other potentially toxic substances, which are reduced
to non-harmful components through a special chemical process. If you require
more details about HP’s product take-back program, contact your dealer or
your nearest HP Sales Office.

The cathode ray tube used in this monitor does not contain cadmium.

English 17

HP 19” Color Monitor User’s Guide

Hardware Warranty

Hardware Warranty

This is your HP Monitor Hardware Warranty Statement. Warranty terms may be
different in your country. If so, your Authorized HP Dealer or Hewlett-Packard Sales
and Service Office can give you details.

For Consumer Transactions in Australia and New Zealand: The warranty terms
contained in this statement, except to the extent lawfully permitted, do not exclude,
restrict or modify and are in addition to the mandatory statutory rights applicable to
the sale of this product to you.

Limited Monitor Hardware Warranty

Model Warranty Period Service provided

Model D2842A
Model D2842W

3 years—unless original end-user
customer has otherwise agreed to
a shorter period of warranty at
the time of purchase.

On-site service for first year, and
return to an HP or
repair-authorized reseller
service-center for the following
two years.

Hewlett-Packard (HP) warrants this monitor hardware product against defects in
materials and workmanship for the applicable warranty period stated above,
commencing from the date of purchase by you, the original end-user customer. If you
return this monitor hardware product with a defect as defined above, during the
warranty period, to an HP-authorized reseller or service center, HP will either, at its
option, repair or replace the defective product with a new or equivalent-to-new unit of
the same or equivalent model. Should HP be unable to repair or replace the product
within a reasonable amount of time, your alternate exclusive remedy shall be a refund
of the purchase price upon return of the product.

If you purchased this monitor hardware product for use with an HP personal computer
(Vectra, Brio or Kayak), please refer to the terms and conditions of the HP Hardware
Warranty statement provided with your HP personal computer (Vectra, Brio or Kayak),
including limitations, your responsibilities and method for obtaining warranty service.

If you purchased this monitor hardware product for use with an HP Workstation,
please refer to the terms and conditions of the HP warranty statement provided with
your HP workstation, including limitations, your responsibilities and method for
obtaining warranty service.

18 English

HP 19” Color Monitor User’s Guide

Hardware Warranty

Limitation of Warranty

The above warranty shall not apply to defects resulting from: misuse (including
"burned" screens); unauthorized modification; operation or storage outside the
environmental specifications for this monitor product; in-transit damage; improper
maintenance; or defects resulting from use of non-HP software, accessories, media,
supplies, consumables, or such items not designed for use with this product.

HP MAKES NO OTHER EXPRESS WARRANTY, WHETHER WRITTEN OR ORAL,
WITH RESPECT TO THIS PRODUCT. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO
THE DURATION OF THE EXPRESS WARRANTY SET FORTH ABOVE.

Some states or provinces do not allow limitations on warranty, so the above limitation
or exclusion may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state, or province to province.

Limitation of Liability and Remedies

THE REMEDIES PROVIDED ABOVE ARE YOUR SOLE AND EXCLUSIVE REMEDIES.
IN NO EVENT SHALL HP BE LIABLE FOR ANY OTHER DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON
WARRANTY, CONTRACT, TORT, OR ANY OTHER LEGAL THEORY.

The foregoing limitation of liability shall not apply in the event that any HP product
sold hereunder is determined by a court of competent jurisdiction to be defective and
to have directly caused bodily injury, death, or property damage; provided, that in no
event shall HP's liability for property damage exceed the greater of $50,000 or the
purchase price of the specific product that caused such damage.

Some states or provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.

English 19

HP 19” Color Monitor User’s Guide

Regulatory Information

Regulatory Information

DECLARATION OF CONFORMITY

according to ISO/IEC Guide 22 and EN 45014

Manufacturer’s Name: HEWLETT-PACKARD

Manufacturer’s Address:

declares, that the product:

conforms to the following Product Specifications:

Product Name:

Model Number:

SAFETY

EMC

5, Avenue Raymond Chanas - EYBENS
38053 GRENOBLE CEDEX 09
FRANCE

HP 90 19-inch Color Monitor
D2842*(See Note)

International: IEC 60950:1991 + A1 + A2 +A3 +A4

Europe: EN 60950:1992 + A1 + A2 +A3 +A4

CISPR 22:1993+A1 / EN 55022:1994 - Class B 1)
EN 50082-1:1992
IEC 801-2:1992 / prEN 55024-2:1992 - 4kV CD, 8 kV AD
IEC 801-3:1984 - 3V/m
IEC 801-4:1988 / prEN 55024-4:1992 - 1 kV Power Lines

IEC 555-2:1982 + A1:1985 / EN 60555-2:1987
IEC 1000-3-3:1994 / EN 61000-3-3:1995

Supplementary information:

accordingly:
the EMC Directive 89/336/EEC, the Low Voltage Directive 73/23/EEC both amended by the Directive 93/68/EEC.

NOTE

: * can be alphanumeric character, including blank.

Grenoble, December 1998. Quality Manager

The product herewith complies with the requirements of the following Directives and carries the CE mark

Jean Marc JULIA

20 English

HP 19” Color Monitor User’s Guide

Regulatory Information

Notice for the USA: FCC Statement

Federal Communications Commission (FCC) Radio

Frequency Interference Statement (USA Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protections against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to correct the interference by one or more of the
following measures:

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and the receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

•

WARNING Hewlett-Packard’s FCC Compliance Tests were conducted with HP-supported peripheral devices and HP

shielded cables, such as those you receive with your system. Cables used with this computer must be properly
shielded to comply with the requirements of FCC.

Changes or modifications not expressly approved by Hewlett-Packard could void the user’s authority to operate
the equipment.

X-Ray Radiation Notice

When operating, this product emits x-rays; however, it is well shielded and meets the safety and health
requirements of various countries, such as the Radiation Act of Germany and the Radiation Control for Health
and Safety Act of the United States.

Radiation emitted by this product is less than 0.1 mR/hr (1uSv/hr) at a distance of 10 centimeters from the
surface of the cathode ray tube. The x-ray radiation primarily depends on the characteristics of the cathode ray
tube and its associated low voltage and high voltage circuitry. Internal controls have been adjusted to ensure
safe operation. Only qualified personnel should perform any internal adjustments as specified in the service
manual for this product.

Replace the cathode ray tube with an identical CRT only.

Notice for Canada

This Class “B” digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

General Notice

The HP D2842A/W 19-inch Color Monitor has been tested according to MPR 1990:8 for Emission properties and
meets the guidelines as given by MPR 1990:10 (2.01 - 2.04).

English 21

HP 19” Color Monitor User’s Guide

Regulatory Information

Notice for Japan

22 English

HP 19” Color Monitor User’s Guide

TCO 99 - Ecology Energy Emissions Ergonomics

TCO 99 - Ecology Energy Emissions Ergonomics

Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided
you with a product developed for professional use. Your purchase has also contributed to reducing the burden
on the environment and also to the further development of environmentally adapted electronics products.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encouraging the adaptation of
goods and services to the environment. The main problem, as far as computers and other electronics equipment
are concerned, is that environmentally harmful substances are used both in the products and during their
manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most
of these potentially damaging substances sooner or later enter nature.

There are also other characteristics of a computer, such as energy consumption levels, that are important from
the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity
generation have a negative effect on the environment (e.g. acidic and climate-influencing emissions, radioactive
waste), it is vital to save energy. Electronics equipment in offices is often left running continuously and thereby
consumes a lot of energy.

What does labelling involve?

This product meets the requirements for the TCO'99 scheme which provides for international and
environmental labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO
(The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish
Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration).

Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric
and magnetic fields, energy consumption and electrical and fire safety.

The environmental demands impose restrictions on the presence and use of heavy metals, brominated and
chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be
prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered
to in each country where the company implements its operational policy.

The energy requirements include a demand that the computer and/or display, after a certain period of inactivity,
shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the
computer shall be reasonable for the user.

Labelled products must meet strict environmental demands, for example, in respect of the reduction of electric
and magnetic fields, physical and visual ergonomics and good usability.

Below you will find a brief summary of the environmental requirements met by this product. The complete
environmental criteria document may be ordered from:

TCO Development
SE-114 94 Stockholm, Sweden
Fax: [phone]
Email (Internet): [e-mail]

Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet,
using the address:

http://www.tco-info.com/

English 23

HP 19” Color Monitor User’s Guide

TCO 99 - Ecology Energy Emissions Ergonomics

Environmental requirements

Flame retardants

Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to
prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame
retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are
chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing
bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive
damage in fish-eating birds and mammals, due to the bio-accumulative
found in human blood and researchers fear that disturbances in foetus development may occur.

The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain
flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit
boards since no substitutes are available.

Cadmium

Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays.
Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that
batteries, the colour-generating layers of display screens and the electrical or electronics components must not
contain any cadmium.

Mercury

Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high
doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also demands
that mercury is not present in any of the electrical or electronics components associated with the labelled unit.

2

2.

CFCs (freons)

The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and
assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break
down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of
ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence.

Lead2.

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system
and in higher doses, causes lead poisoning. The relevant TCO´99 requirement permits the inclusion of lead since
no replacement has yet been developed.

1

processes. Flame retardants have been

1. Bio-accumulative is defined as substances which accommodate within living organisms.

2. Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative

24 English

*

* HP. Et tout devient possible.

Paper not bleached with chlorine

Part Number : 5967-9510
Printed 12/98 in Korea