HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
ProLiant BL e-Class Server Blade Enclosure
ProLiant BL e-Class Server Blade Enclosure
ProLiant BL e-Class Server Blade EnclosureProLiant BL e-Class Server Blade Enclosure
(shown with 20 ProLiant BL10e server blades)
(shown with 20 ProLiant BL10e server blades)
(shown with 20 ProLiant BL10e server blades)(shown with 20 ProLiant BL10e server blades)
ProLiant BL10e Generation 2 (G2) Server Blade
ProLiant BL10e Generation 2 (G2) Server Blade
ProLiant BL10e Generation 2 (G2) Server BladeProLiant BL10e Generation 2 (G2) Server Blade
DA - 11686 Worldwide — Version 13 — October 8, 2004
Page 1
QuickSpecs
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
Overview
What's New
What's New
What's NewWhat's New
One Ultra-Low Voltage Intel® Pentium® M 1GHz processor with 1-MB L2 cache
Support for DDR memory
ProLiant BL10e G2 Server Blade includes:
ProLiant BL10e G2 Server Blade includes:
ProLiant BL10e G2 Server Blade includes:ProLiant BL10e G2 Server Blade includes:
One Ultra-Low Voltage ULV Intel Pentium M processor with 1-MB L2 cache (400-MHz front side bus)
ServerWorks GC-SL chipset
512-MB C2100 Registered ECC DDR DIMM Memory standard expandable to 1024MB (2 DIMM slots)
Two NC3163 Fast Ethernet NIC PCI 10/100 full WOL and PXE Integrated
One 40-GB Ultra ATA/100 hard drive
Server blades protected by HP Services, including a limited one year parts warranty with optional service uplifts available
ProLiant BL e-Class Server Blade Enclosure includes:
ProLiant BL e-Class Server Blade Enclosure includes:
ProLiant BL e-Class Server Blade Enclosure includes:ProLiant BL e-Class Server Blade Enclosure includes:
3U high rack-mountable chassis with 20 server blade bays
Can be purchased with 20 licenses for new ProLiant Essentials Rapid Deployment Pack at 50% of standard license list price!
Dual, 1+1 redundant hot-plug power supplies
Four, 2+2 redundant hot-plug fans
Three available interconnect options: C-GbE Interconnect Switch; RJ-45 Patch Panel; and RJ-21 Patch Panel
Server blade enclosure protected by HP Services, including a limited three year warranty with optional service uplifts available
ProLiant BL e-Class Integrated Administrator features:
ProLiant BL e-Class Integrated Administrator features:ProLiant BL e-Class Integrated Administrator features:
Acts as a combination terminal server and remote power controller, enabling out-of-band, secure, serial console connections to all server blades and
the optional interconnect switch
Enclosure, interconnect switch and server blade health monitoring and alerts
Command-line and browser-based management interfaces, including access permissions, for the server blades and the enclosure
Provides access to the interconnect optional switch management interfaces
SNMP, web and scriptable command-line interfaces
PLUS
PLUS
PLUSPLUS
DA - 11686 Worldwide — Version 13 — October 8, 2004
Page 2
QuickSpecs
Overview
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
PLUS
PLUS
PLUSPLUS
or
oror
oror
or
oror
a. C-GbE Interconnect Switch
Configuration Steps
Configuration Steps
Configuration StepsConfiguration Steps
For a complete configuration of the HP ProLiant BL e-Class system, do the following:
Select ProLiant BL10e G2 server blades sold [in a single-pack or 10-pack]
1.
PLUS
PLUS
PLUSPLUS
Select Server Blade Enclosures (each can hold up to 20 ProLiant BL10e G2 server blades). The enclosure can be purchased bundled with 20 licenses
2.
for ProLiant Essentials Rapid Deployment Pack at 50% of the standard license price.
(
NOTE:
NOTE:
Rapid Deployment Pack is optimized for configuring and deploying ProLiant BL10e G2 server blades and enable unique features such as
NOTE:NOTE:
blade "rip and replace" for effortless server redeployment.)
PLUS
PLUS
PLUSPLUS
Select one of the three Interconnect Tray options for each server blade enclosure
3.
(
NOTE:
NOTE:
Each interconnect tray includes an Integrated Administrator module.):
NOTE:NOTE:
a. C-GbE Interconnect Switch (with 4 10/100/1000T Gigabit Ethernet
RJ-45 uplinks for up to 40-to-1 network cable reduction!)
OR
OR
OROR
b. RJ-45 Patch Panel (with 40 RJ-45 connectors)
OR
OR
OROR
b. RJ-45 Patch Panel
c. RJ-21 Patch Panel
c. RJ-21 Patch Panel (with 4 RJ-21 connectors for cable aggregation behind the enclosure)
(
NOTE:
NOTE:
If suitable for your environment, select also the RJ-21 to RJ-45 Cable Option kit.)
NOTE:NOTE:
DA - 11686 Worldwide — Version 13 — October 8, 2004
Page 3
QuickSpecs
Standard Features
HP ProLiant BL10e G2 Server Blade
HP ProLiant BL10e G2 Server Blade
HP ProLiant BL10e G2 Server BladeHP ProLiant BL10e G2 Server Blade
Internal StorageInternal Storage
Warranty for the Server
Warranty for the Server
Warranty for the ServerWarranty for the Server
Blade
Blade
BladeBlade
Form Factor
Form Factor
Form FactorForm Factor
Product Demo
Product Demo
Product DemoProduct Demo
HP ProLiant BL10e G2 Server Blade Enclosure
HP ProLiant BL10e G2 Server Blade Enclosure
HP ProLiant BL10e G2 Server Blade EnclosureHP ProLiant BL10e G2 Server Blade Enclosure
Dimensions
Dimensions
DimensionsDimensions
Rack Capability
Rack Capability
Rack CapabilityRack Capability
Server Blade Enclosure
Server Blade Enclosure
Server Blade EnclosureServer Blade Enclosure
includes
includes
includesincludes
Warranty for Server Blade
Warranty for Server Blade
Warranty for Server BladeWarranty for Server Blade
Enclosure
Enclosure
EnclosureEnclosure
One Ultra-Low Voltage Intel Pentium M 1GHz processor
1MB Level-2 on-die Cache
ServerWorks GC-SL chipset
NOTE:
NOTE:
For more information regarding ServerWorks, please see the following URL:
NOTE:NOTE:
http://www.serverworks.com/products/overview.html
Standard
Maximum
Two NC3163 Fast Ethernet NIC PCI 10/100 full WOL and PXE Integrated
Hard Drive
1 year on parts, 9x5 NBD. HP Care Pack warranty upgrades available to add labor, on-site service, faster response times,
and longer terms to the standard server blade warranty.
Server blades plug vertically into HP ProLiant BL e-Class Server Blade Enclosure
To view the Product Demo, please see the following URL, then click on "PRODUCT DEMO":
5.25 inch Height (3U), 17.5 inch Width, 28.35 inch Depth
Bays for up to 20 ProLiant BL10e G2 server blades
Mounts in HP, HP-branded, third-party, and Telco racks. Rack mounting hardware for HP, Compaq-branded and third-
party racks ships standard with each server blade enclosure. Telco rack-mounting hardware is a separately available option
kit.
Rear bay for 1 of 3 Interconnect Tray configurations for network cable management (see below).
Two (2) Diagnostic Adapters for connecting keyboard, video, mouse and other devices locally to individual server blades
ProLiant Essentials Foundation Pack for ProLiant BL Servers, includes the Insight Managerä 7 and Management Agents CD
and ProLiant Essentials Rapid Deployment Pack CD (trial version - 7-days, 10 nodes).
(
NOTE:
NOTE:
The ProLiant BL e-Class server blade enclosure can also be purchased bundled with 20 licenses for Rapid
NOTE:NOTE:
Deployment Pack at 50% of the standard license price.)
Four (2+2 redundant) hot- plug fans
Dual (1+1 redundant) hot- plug power supplies (600 watts each), power cords
Server blade blanks (to fill 19 of the 20 server blade bays)
Rack mounting hardware for HP, Compaq-branded and third-party racks
Null-modem cable for serial connection to the Integrated Administrator serial "Console" connector
HP Documentation CD
3 years on parts, labor and on-site service. HP Care Pack warranty upgrades available to add faster response times to the
Each interconnect tray includes the Integrated Administrator module.
NOTE:NOTE:
Warranty
Warranty
WarrantyWarranty
Please see the following (3) interconnect tray configurations for accessing server blade network connections:
ProLiant BL e-Class C-GbE Interconnect Switch (with 4 Gigabit Ethernet uplinks for up to 40-to-1 network cable reduction!)
3 years on parts, labor and on-site service. HP Care Pack warranty upgrades available to add faster response times to the
standard warranty.
See details below.
See "Other Options" below for RJ-21 to RJ-45 Cable option kit.
DA - 11686 Worldwide — Version 13 — October 8, 2004
Page 4
QuickSpecs
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
Standard Features
HP ProLiant BL e-Class Integrated Administrator ver. 1.40 Features
HP ProLiant BL e-Class Integrated Administrator ver. 1.40 Features
HP ProLiant BL e-Class Integrated Administrator ver. 1.40 FeaturesHP ProLiant BL e-Class Integrated Administrator ver. 1.40 Features
Out-of-band local console and remote network access to the server blade enclosure and all 20 server blades via
(one) RJ-45 10/100T Fast Ethernet and (one) RS-232 management connectors
Provides local and remote access to the ProLiant BL e-Class C-GbE Interconnect Switch command console and
browser-based management interfaces
SNMP, Web (via HTTPS) and command-line interfaces (via Console connector, Telnet and Secure Shell)
Remotely power on/off/reboot server blades and enclosures
Remotely toggle on/off unit identification LEDs (UID) of server blades and enclosures
Monitors and controls the enclosure fans, temperature sensors, power supplies, interconnect switch and server blade
status
Connect to each server blade's serial text console for enabling full control over server blade's
Power-On Self Test (POST) and boot process, including the ROM-Based Setup Utility (RBSU).
NOTE:
NOTE:
For ProLiant BL10e G2 server blades running Windows® 2000 Server, there is now available a Serial
NOTE:NOTE:
Console for Windows utility that provides serial-based administrative functionality using the Integrated
Administrator remote console feature. For more information and to download the Serial Console for Windows
utility, go to the following page:
User administration for up to 25 users. Server blade bay privileges can be set on a per-user basis
Virtual NMI button generates non-maskable interrupt for crash debug and analysis
Support for Network Time Protocol (NTP)
IP Security feature limits access to user-specified IP addresses
AlertMail enables email alerts for system events
More than 100 scriptable commands enable automated management
Selective enabling of all protocols, such as Telnet
Logging of operating system console, server blade and enclosure hardware events, user actions and invalid login
attempts
Emergency server blade enclosure shutdown caused by a critical temperature
Enclosure Link (2) connectors reserved for future use.
CAUTION:
CAUTION:
CAUTION: CAUTION:
external device to these enclosure link (RJ-45) connecters may damage your external device.
For more information on the ProLiant BL e-Class Integrated Administrator, please visit the Web site at:
The enclosure link (RJ-45) connectors on the interconnect tray are not to be used. Connecting an
HP ProLiant BL e-Class C-GbE Interconnect Switch Features
HP ProLiant BL e-Class C-GbE Interconnect Switch Features
HP ProLiant BL e-Class C-GbE Interconnect Switch FeaturesHP ProLiant BL e-Class C-GbE Interconnect Switch Features
Provides up to a 40-to-1 reduction in network cables for each server blade enclosure using a pair of non-blocking
layer 2 switch modules
Four RJ-45 10/100/1000T Gigabit Ethernet uplinks
Forty 10/100T Ethernet ports dedicated to server blade-to-interconnect switch network communications
Communicate with all 40 server blade network controllers through any one uplink connector and the management
connector
Spanning tree protocol for loop-free path redundancy
Browser, scriptable CLI, and console-based interfaces for local and remote interconnect switch management
Manage entire interconnect switch through the Integrated Administrator connectors or any uplink connector
Telnet, RMON and SNMP support; SNMP-based scripting utility with example scripts
256 Port-based IEEE 802.1Q tagged VLANs per switch processor module
IGMP (internet group management protocol) snooping and quality of service (QoS) packet prioritization
TFTP server support for rapid deployment of multiple interconnect switches and to provide backup and restore
capabilities
Industry-standard design compatible with industry-standard network components from leading network
manufacturers
Fully pre-configured for rapid deployment and immediate operation in ProLiant BL e-Class enclosure
For more information on the ProLiant BL e-Class C-GbE Interconnect Switch, please visit the Web site at:
NOTE:NOTE:
devices have been tested for use with the ProLiant BL10e and the Diagnostic Adapter:
This Web site is available in English only.
Server blades also support USB keyboard and USB mouse attached via the Diagnostic Adapter. The following USB
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
.
USB Easy Access Keyboard (Carbon) (PN 267146-xx8)
USB Easy Access Keyboard (Carbonite) (PN DC168B#)
USB 2-Button Scroll Mouse (Carbon) (PN 195255-B25)
USB 2-Button Scroll Mouse (Carbonite) (PN DC172B)
USB Floppy (PN 304707-B21)
DA - 11686 Worldwide — Version 13 — October 8, 2004
Page 6
QuickSpecs
Standard Features
ProLiant Essentials
ProLiant Essentials
ProLiant EssentialsProLiant Essentials
Foundation Pack
Foundation Pack
Foundation PackFoundation Pack
Software for the ProLiant
Software for the ProLiant
Software for the ProLiantSoftware for the ProLiant
BL Server
BL Server
BL ServerBL Server
ProLiant Essentials Rapid
Deployment Pack
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
Rapid Deployment Pack (RDP) is an automated deployment and provisioning solution for
all ProLiant servers. RDP includes the Altiris Deployment Solution and ProLiant Integration
Module featuring ProLiant server pre-configured events for OS installation, and optimized
software drivers, firmware and management agents. Every RDP CD includes 10-node trial
licenses for evaluation purposes. RDP requires a license for each server deployed and are
available for purchase with blade servers. For more information, visit
http://www.hp.com/servers/rdp
.
HP Systems Insight Manger
Management Agents
Subscriber's Choice
ROMPaq
and
configuration utilities
, support software,
HP Systems Insight Manager (HP SIM) help maximize system uptime and performance and
reduce system maintenance costs by providing proactive notification of problems before
those problems result in unplanned downtime or reduced productivity. HP SIM is easy to set
up to work with the Insight Management Agents, integrated Light-Out and Remote Insight
Light-Out Edition, and Version Control Agents to deliver robust fault, configuration, and
asset management as well as remote administration. With HP Systems Insight Manager
customers will also be able to take advantage of role-based security; the ability to manage
ProLiant, Integrity, and HP9000 systems; and plug-ins for storage, client, printer, and
power management as well as server rapid deployment, performance management, and
workload management. For more details on HP Systems Insight Manager visit
http://www.hp.com/go/hpsim
The Management Agents form the foundation for HP's Intelligent Manageability strategy.
They provide direct, browser-based access to in-depth instrumentation built into HP servers,
workstations, desktops, and portables, and send alerts to HP Systems Insight Manager and
other enterprise management applications in case of subsystem or environmental failures.
For additional information about the Management Agents and other management
products from HP, please visit the management Web site at
http://www.hp.com/servers/manage
Subscriber's Choice Driver and Support Alerts/Notifications is a web-based email
subscription service that provides software and driver change notifications for ProLiant
products. Sign up at
and customize your profile to receive various new alerts as they become available, on a
weekly or monthly basis.
The latest software, drivers, and firmware fully optimized and tested for your ProLiant server
and options, available in the RDP CD, SmartStart or downloadable from Software and
Drivers download pages, linked from the SmartStart website at
http://www.hp.com/servers/smartstart
http://www.hp.com/go/subscriberschoice
.
.
.
Optional ProLiant
Optional ProLiant
Optional ProLiantOptional ProLiant
Essentials Value Packs
Essentials Value Packs
Essentials Value PacksEssentials Value Packs
Survey Utility and diagnostics
utilities
NOTE:
NOTE:
NOTE: NOTE:
http://www.hp.com/servers/proliantessentials
For more information regarding ProLiant Essentials Software, please see the following URL:
Optional software offerings that selectively extend the functionality of an Adaptive Infrastructure to address specific business
problems and needs:
Workload Management Pack - provides easier management of complex environments, improving overall server
utilization and enabling Windows® 2000 customers for the first time to confidently deploy multiple applications on
a single multiprocessor ProLiant Server.
Performance Management Pack - a performance management solution that identifies and explains hardware
performance bottlenecks on ProLiant servers and attached options enabling users to better utilize their valuable
resources.
Intelligent Networking Pack - detects and analyzes network bottlenecks or broken networking linkages and steers
traffic to the optimum route based on network conditions.
NOTE:
NOTE:
Flexible and volume quantity license kits are available for ProLiant Essentials Value Packs. Refer to
NOTE:NOTE:
http://www.hp.com/servers/proliantessentials
information.
DA - 11686 Worldwide — Version 13 — October 8, 2004
The most advanced configuration analysis, reporting and troubleshooting utilities used by
HP and at your fingertips, available in SmartStart.
or the various ProLiant Essentials Value Pack product QuickSpecs for more
SmartStart is a tool that simplifies single server setup, providing a rapid way to deploy reliable and consistent server
configurations. SmartStart 7.00 and later can now deploy the ProLiant BL20P G3 and ProLiant BL40P servers, using the I/O
port with an attached USB CD-ROM device. To obtain a copy of SmartStart for your blade server, redeem the coupon that is
included with your Blade server or order your copy from the SmartStart web site. For more information, please visit the
SmartStart Web site at
SmartStart version supported (minimum): SmartStart 6.20
ACPI 1.0b compliant
SDG 3.0 compliant
Microsoft Logo certifications
MIB-II (RFC 1213), Bridge MIB (RFC 1493), Interface MIB (RFC 2233), 801.1Q MIB (RFC 2684), RMON1 MIB (RFC 1757)
groups 1, 2, 3, and 9, and Ethernet MIB (RFC1643) (ProLiant BL e-Class C-GbE Interconnect Switch interconnect tray
option)
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.3ac and 802.1Q, IEEE 802.1Q, and IEEE
Insight Manager 7
HP Systems Insight Manager
ROM Based Setup Utility (RBSU)
Automatic Server Recovery (ASR-2)
Enclosure Self Recovery (ESR)
Advanced Configuration and Power Interface Specification Ready (ACPI)
Server Blade and Enclosure Health Logs
Redundant Power Supply Utility
Power Down Utility
Pre-Failure Warranty (covers processors, hard drives and memory)
HP Interconnect Switch Management System and Utilities (included with the ProLiant BL e-Class C-GbE Interconnect
Switch interconnect tray option)
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
http://www.hp.com/servers/smartstart
.
Availability
Availability
AvailabilityAvailability
Security
Security
SecuritySecurity
Redundant Hot-Plug Power Supplies (ProLiant BL e-Class Server Blade Enclosure)
Redundant Hot-Plug Fans (ProLiant BL e-Class Server Blade Enclosure)
ECC Memory (ProLiant BL10e Server Blade)
Redundant ROM (ProLiant BL10e Server Blade)
Support for ProLiant network adapter teaming
Dual network communication paths to each server blade using redundant, non-blocking layer 2 switch modules
Redundant inter-module communication links
Two redundant uplink ports per each interconnect switch module
IEEE 801.1D Spanning tree protocol for loop-free path redundancy
Redundant configurable community strings and SNMP trap manager hosts
IEEE 802.3ad automatic multi-link load balancing and link failover (excluding LACP)
Power-on password
Administrator's password
Secure Shell (SSH) access through the Integrated Administrator serial console
ProLiant BL e-Class C-GbE Interconnect Switch interconnect tray option security
Multilevel user names and passwords with configurable time out period setting
Ability to disable web-based and Telnet access to the switch user interfaces
256 IEEE 802.1Q tagged VLANs per interconnect switch module
Unicast and multicast static MAC address packet filtering table (layer 2 access control list)
Ability to specify the IP based management stations that are allowed to access each switch
Restriction on the maximum number of MAC addresses learned on a per port basis
Secure shell (SSH) access to the switch command line and menu driven interfaces via the Integrated Administrator
DA - 11686 Worldwide — Version 13 — October 8, 2004
Rack 10000 series CabinetsRack 10000 series Cabinets
The increasing power of new high-performance processor technology requires increased cooling efficiency for rack-mounted
servers. The 10000 Series Racks provide enhanced airflow for maximum cooling, allowing these racks to be fully loaded
with servers using the latest processors.
CAUTION:
CAUTION: If a third-party rack is used, observe the following additional requirements to ensure adequate airflow and to
CAUTION:CAUTION:
prevent damage to the equipment
Front and rear doors: If your 42U server rack includes closing front and rear doors, you must allow 5,350 sq cm (830
square inches) of hole evenly distributed from top to bottom to permit adequate airflow (equivalent to the required
64 percent open area for ventilation).
Side: The clearance between the installed rack component and the side panels of the rack must be a minimum of 7
cm (2.75 inches)
CAUTION:
CAUTION:
CAUTION: CAUTION:
ensures proper airflow. Using a rack without blanking panels results in improper cooling that can lead to thermal damage.
NOTE:
NOTE:
NOTE: NOTE:
Please consult the Setup & Installation Guide for the server for additional details.
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
.
.
Always use blanking panels to fill all remaining empty front panel U-spaces in the rack. This arrangement
Service and Support
Service and Support
Service and SupportService and Support
Three-year limited warranty, including hardware diagnostic support, pre-failure warranty (coverage of hard drives, memory
and processors). The warranty is fully supported by HP Services and a worldwide network of resellers and service providers. In
addition 90-day's getting started software telephone support may be covered under the warranty or available for an
additional fee. Enhancements to warranty services are available through HP Care Pack services.
NOTE:
NOTE:
Sever Blade Limited Warranty includes 3 year Parts, 3 year Labor, 3-year on-site support.
NOTE:NOTE:
NOTE:
NOTE:
NOTE: NOTE:
support.
Care Pack services provide a range of life cycle support options that let you choose the service levels that meet your business
requirements, from basic to mission-critical.
A full range of HP Care Pack hardware and software services are available including:
HP Care Pack services for ProLiant BL p-Class server blades, cover the server blade and the p-Class blade enclosure that the
server blade is installed in as well as interconnects, power enclosure with power supplies and power distribution.
NOTE:
NOTE:
NOTE:NOTE:
worldwide Web site on the internet at:
NOTE:
Server Blade Enclosure and Interconnects Limited Warranty includes 3 year Parts, 3 year Labor, 3-year on-site
Installation and start up
Education courses
Extended onsite hardware coverage hours from same business day 13 hours, 5 day to 24 hours, 7 days call window
with options including 4-hour response or 6-hour Call To Repair
Comprehensive range of software technical support for Microsoft, Linux, ProLiant Essentials and VMWare-based IT
solutions helping to deliver high level of application availability. Response times range from 30 mins for critical
problems to 2 hours.
System Management, Performance Services and Mission Critical Support Solution
For more information on HP Care Pack services, contact any of our worldwide sales offices or resellers or visit our
http://www.hp.com/hps/carepack
For more complete information on HP Services offerings, customers and resellers, please visit us at:
Additional information regarding worldwide limited warranty and technical support is available at:
DA - 11686 Worldwide — Version 13 — October 8, 2004
P1GHz-1MB (ULV), 512-P1GHz-1MB (ULV), 512MB, 40-GB ATA
MB, 40-GB ATA
MB, 40-GB ATAMB, 40-GB ATA
333773-B21 (1 pack)
333774-B21 (10 pack)
Processor
Processor
ProcessorProcessor
Cache Memory
Cache Memory
Cache MemoryCache Memory
Memory
Memory
MemoryMemory
Network Controller
Network Controller
Network ControllerNetwork Controller
Hard Drive
Hard Drive
Hard DriveHard Drive
Form Factor
Form Factor
Form FactorForm Factor
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
One Ultra-Low Voltage Intel Pentium M 1GHz processor
1-MB Level-2 on-die cache
512 MB (Standard) to 1024 MB (Maximum) PC2100 Registered ECC DDR DIMM Memory
standard (1x512 MB)
Two NC3163 Fast Ethernet NIC PCI 10/100 full WOL and PXE Integrated
One 40-GB Ultra ATA/100 5,400 rpm Non-Hot Plug 2.5" hard drive
Plugs vertically into HP ProLiant BL10e G2 Server Blade Enclosure
DA - 11686 Worldwide — Version 13 — October 8, 2004
NOTE: NOTE:
with a single activation key. The quantity ordered of this part number will be the quantity of licenses
included in the kit in the form of a corresponding activation key. Use the same key to activate all
licenses in the actual quantity ordered. For a given order, one kit will be delivered with the activation
key, and documentation
AKA Tracking License
NOTE:
NOTE:
NOTE: NOTE:
number entitles the customer to deploy additional licenses of the product under the terms of the
existing Activation Key Agreement. Nothing is delivered in conjunction with the purchase of this part
number. Visit http://h18004.www1.hp.com/products/servers/proliantessentials/license/akalic.html for
more information on Activation Key Agreements.
NOTE: NOTE:
with a single activation key. The quantity ordered of this part number will be the quantity of licenses
included in the kit in the form of a corresponding activation key. Use the same key to activate all
licenses in the actual quantity ordered. For a given order, one kit will be delivered with the activation
key, and documentation
ProLiant Essentials Intelligent Networking Pack, Single Server License
NOTE: NOTE:
with a single activation key. The quantity ordered for this part number will be the quantity of licenses
included in the kit in the form of a corresponding activation key. Use the same key to activate all
licenses in the actual quantity ordered. For a given order, one kit will be delivered with the activation
key, and documentation.
HP UPS R1500 XR (1440VA, 1340 Watt), Low Voltage (NA)
HP UPS R1500 XR (1500VA, 1340 Watt), High Voltage (Int'l)
HP UPS R1500 XR (1500VA, 1340 Watt), Low Voltage (Japan)
HP UPS R3000 XR (2880VA, 2700 Watt), Low Voltage (NA)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage (NA)
HP UPS R3000 XR (2400VA, 2250 Watt), Low Voltage (Japan)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage (Japan)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage (Int'l – detachable cord)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage (16A IEC309 Plug)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage
(16A CEE 7/7 SCHUKO Plug)
HP UPS R3000 XR (3000VA, 2700 Watt), High Voltage (16A BS-546 Plug)
Rack-Mountable UPS R6000 (6000VA, 6000 Watt) High Voltage (NA)
NOTE:
NOTE:
NOTE: NOTE:
Rack-Mountable UPS R6000 (6000VA, 6000 Watt) High Voltage (Int'l)
NOTE:
NOTE:
NOTE: NOTE:
Rack-Mountable UPS R6000 (6000VA, 6000 Watt) High Voltage (Japan)
NOTE:
NOTE:
NOTE: NOTE:
UPS R12000 XR N+ x (200-240V) (WW-hardwired)
NOTE:
NOTE:
NOTE: NOTE:
The UPS R6000 has a hardwired input.
The UPS R6000 has a hardwired input.
The UPS R6000 has a hardwired input.
The UPS R12000 XR has a hardwired input and output.
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
Supports tower and rack UPS XR models ranging from 1000 – 3000VA.
Supports tower and rack UPS XR models ranging from 1000 – 3000VA.
2U each, two ERM maximum.
2U each, one ERM maximum.
3U each, two ERM maximum.
4U each, two ERM maximum.
The R12000 XR BackPlate Kit has a hardwired input.
The R12000 XR BackPlate Kit has a hardwired input.
Supports R6000 UPS series only.
192189-B21
192185-B21
218971-B21
192188-B21
347224-B21
217800-B21
325361-001
325361-B21
347225-B21
DA - 11686 Worldwide — Version 13 — October 8, 2004
Page 13
QuickSpecs
Options
Modular PDUs 1U/0U
Modular PDUs 1U/0U
Modular PDUs 1U/0UModular PDUs 1U/0U
(Up to 32 outlets)
(Up to 32 outlets)
(Up to 32 outlets)(Up to 32 outlets)
NOTE:
NOTE:
NOTE: NOTE:
brackets shipped with the unit
(optimized for 10000 and 9000
series racks).
1U/0U mounting
HP Modular Power Distribution Units (mPDU), Low Volt Model, 24A (100-127 VAC)
(NA, Japan)
NOTE:
NOTE:
NOTE: NOTE:
R3000 XR.
HP Modular Power Distribution Units (mPDU), High Volt Model, 24A (200-240 VAC)
(NA, Japan)
HP Modular Power Distribution Units (mPDU), High Volt Model, 32A (200-240 VAC) (Int'l)
HP Modular Power Distribution Units (mPDU), High Volt Model, 40A (200-240 VAC) (WW)
NOTE:
NOTE:
NOTE: NOTE:
HP Modular Power Distribution Units (mPDU), High Volt Model, 16A (200-240 VAC) (WW)
NOTE:
NOTE:
NOTE:NOTE:
power requirements (country-specific cord needs to be ordered separately; for North America, need IEC
C19 to L6-20P power cord PN: 340653-001). This model may also be used with the high volt UPSs
R3000 XR and R6000.
NOTE:
NOTE:
NOTE: NOTE:
QuickSpecs for additional options including shorter jumper cables and country specific power cords:
-B21 (pallet) used to ship empty racks shipped on a truck
Not all HP equipment is qualified to be shipped in the Rack 10000 series.
Please see the Rack 10000 QuickSpecs for Technical Specifications such as height, width,
For additional information regarding Rack Cabinets, please see the following URL:
Rack Rail Adapter Kit (25" depth)
100 kg Sliding Shelf
Monitor/Utility Shelf - Graphite
Depth Adjustable Fixed Rail
Cable Management D-Rings Kit
Server Console Switch 1 x 4 port (100-230 VAC)
Server Console Switch 1 x 4 port (100-230 VAC) (Int’l)
Server Console Switch 1 x 4 port (100-230 VAC) (Japan)
IP Console Switch Box, 1 x 1 x 16
IP Console Switch Box, 3 x 1 x 16
CPU to Server Console Cable, 12’
CPU to Server Console Cable, 3’
CPU to Server Console Cable, 7’
IP CAT5 Cable 3’, 4 pack
IP CAT5 Cable 6’, 8 pack
IP CAT5 Cable 12’, 8 pack
IP CAT5 Cable 20’, 4 pack
IP CAT5 Cable 40’, 1 pack
Switch Box Connector Kit (high voltage) (Int'l)
TFT5600 Rack Keyboard Monitor
TFT7210R Rack Mounted 17" Monitor
NOTE:
NOTE:
For a complete list of Monitors please view the following URL:
Norway
Sweden/Finland
Switzerland
Portugal
Belgium
Japan
International
.
Rack Options for HP,
Rack Options for HP,
Rack Options for HP,Rack Options for HP,
Compaq-branded, Third
Compaq-branded, Third
Compaq-branded, ThirdCompaq-branded, Third
Party and Telco racks
Party and Telco racks
Party and Telco racksParty and Telco racks
Telco rack-mounting hardware kit for ProLiant BL e-Class Server Blade Enclosure
Enclosure Shipping Bracket Kit
NOTE:
NOTE:
NOTE: NOTE:
When shipping an enclosure in a rack shipping brackets must be installed to the rack.
DA - 11686 Worldwide — Version 13 — October 8, 2004
266076-B21
293119-B21
Page 18
QuickSpecs
Options
Service and Support
Service and Support
Service and SupportService and Support
Offerings
Offerings
Offerings Offerings
Services)
(HP Care Pack
NOTE:
NOTE:
The HP Care Pack services for ProLiant BL e-Class server blades cover the server blade and
NOTE:NOTE:
the e-Class blade enclosure that the server blade is installed in as well as the interconnect tray.
Hardware Services On-site Service
Hardware Services On-site Service
Hardware Services On-site ServiceHardware Services On-site Service
Next Business Day On-site Service, 5-Day x 9-Hour Coverage, 3 Years
Next Business Day On-site Service, 5-Day x 9-Hour Coverage, 3 Years , Electronic
4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years
4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years, Electronic
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic
Installation & Start-up Services
Installation & Start-up Services
Installation & Start-up ServicesInstallation & Start-up Services
ProLiant BL e-Class Blade Server Hardware Installation
ProLiant BL e-Class Blade Server Hardware Installation, Electronic
ProLiant BL e-Class Enclosure and Server Blade Hardware Installation
ProLiant BL e-Class Enclosure and Server Blade Hardware Installation, Electronic
Provides for the Installation and Start-up of Compaq's Rapid Deployment Pack on a Customer
supplied server designated as a Deployment Server. Includes the deployment of a single server. This
new server will be deployed using either one of the pre-configured scripts or an image. In addition,
the service will provide for the capture and storage of the configuration of the newly deployed server
and orientation on product usage. To be delivered during standard office ours, standard office days.
Provides for the Installation and Start-up of Compaq's Rapid Deployment Pack on a Customer
supplied server designated as a Deployment Server. Includes the deployment of a single server. This
new server will be deployed using either one of the pre-configured scripts or an image. In addition,
the service will provide for the capture and storage of the configuration of the newly deployed server
and orientation on product usage. To be delivered during standard office ours, standard office days.
Electronic.
NOTE:
NOTE:
For more information, customer/resellers can contact
NOTE:NOTE:
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
UA220A
UA220E
UA221A
UA221E
UA222A
UA222E
UA227A
UA227E
U4960A
U4960E
U5683A
U5683E
http://www.hp.com/services/carepack
DA - 11686 Worldwide — Version 13 — October 8, 2004
Page 19
QuickSpecs
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
Memory
ProLiant BL10e G2 Server Blade
ProLiant BL10e G2 Server Blade
ProLiant BL10e G2 Server BladeProLiant BL10e G2 Server Blade
STANDARD MEMORY
STANDARD MEMORY
STANDARD MEMORYSTANDARD MEMORY
512-MB PC2100 Registered ECC DDR DIMM Memory installed (1 x 512-MB SDRAM DIMM)
STANDARD MEMORY PLUS OPTIONAL MEMORY
STANDARD MEMORY PLUS OPTIONAL MEMORY
STANDARD MEMORY PLUS OPTIONAL MEMORYSTANDARD MEMORY PLUS OPTIONAL MEMORY
Up to 1024 MB PC2100 Registered ECC DDR DIMM Memory is available with the installation of optional SDRAM DIMM memory expansion kits.
Memory
Memory
MemoryMemory
Standard
Standard
StandardStandard
Optional
Optional
OptionalOptional
Optional
Optional
OptionalOptional
Maximum
Maximum
MaximumMaximum
512 MB
512 MB512 MB
512 MB512 MB
640 MB
640 MB512 MB
640 MB640 MB
768 MB
768 MB512 MB
768 MB768 MB
1024 MB
1024 MB
1024 MB1024 MB
512 MB
512 MB512 MB
512 MB128 MB
512 MB512 MB
512 MB256 MB
512 MB512 MB
512 MB
512 MB512 MB
512 MB512 MB
Following are memory options available from HP:
128MB of Advanced ECC PC2100 DDR SDRAM DIMM Memory Kit (1 x 128 MB)
256MB of Advanced ECC PC2100 DDR SDRAM DIMM Memory Kit (1 x 256 MB)
512MB of Advanced ECC PC2100 DDR SDRAM DIMM Memory Kit (1 x 512 MB)
11112222
Slot
Slot
SlotSlot
Empty
Empty
EmptyEmpty
128 MB
128 MB128 MB
256 MB
256 MB256 MB
512 MB
512 MB512 MB
287494-B21
287495-B21
287496-B21
DA - 11686 Worldwide — Version 13 — October 8, 2004
Page 20
QuickSpecs
Technical Specifications
HP ProLiant BL10e G2
HP ProLiant BL10e G2
HP ProLiant BL10e G2HP ProLiant BL10e G2
Server Blade Enclosure
Server Blade Enclosure
Server Blade EnclosureServer Blade Enclosure
Power Supply
Power Supply
Power SupplyPower Supply
Dimensions
Dimensions
DimensionsDimensions
Weight
Weight
WeightWeight
600W, Hot-Plug
600W, Hot-Plug
600W, Hot-Plug600W, Hot-Plug
Redundant
Redundant
RedundantRedundant
(2 standard)
(2 standard)
(2 standard)(2 standard)
Input Specifications
Input Specifications
Input SpecificationsInput Specifications
General Specifications
General Specifications
General SpecificationsGeneral Specifications
Dielectric Voltage
Dielectric Voltage
Dielectric VoltageDielectric Voltage
Withstand
Withstand
WithstandWithstand
Input Transient
Input Transient
Input TransientInput Transient
Susceptibility
Susceptibility
SusceptibilitySusceptibility
NOTES
NOTES
: ProLiant BL e-Class Power Calculator is available from the product page at the following address:
Click "Power Calculator" in the "Support" section.
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
Height
Width
Depth
Interconnect Tray
20 server blades
Enclosure with 2 power supplies
Total weight fully loaded
Two Redundant Power Supplies (optimized to provide full redundancy at 120 and 220
volts)
Normal Line Voltage
Range Input Line
Frequency Range
Power Factor
Input Current
Inrush Current
Holdup Time
Full Output Rating
Minimum Load
Input to Output
Input to Ground
Common and Differential
Mode (superimposed on AC
line)
Differential Mode
5.25 in (13.35 cm) (3U)
17.5 in (44.45 cm)
28.35 in (72.01 cm)
4.5 lb (2.04 kg)
35 lb (15.86 kg)
54.5 lb (24.7 kg)
94 lb (41.73 kg)
100 to 127VAC, 200 to 240VAC
90 to 264VAC
43 to 63Hz
> 0.95 (120Vac/Max Load)
8.5A @ 120VAC, 4.3A @ 240VAC
25A
25mS
600W
1500Vac or 2150Vdc (1 Min.)
1500Vac or 2150Vdc (1 Min.)
2200V
1100V
Non-Hot Plug Ultra
Non-Hot Plug Ultra
Non-Hot Plug UltraNon-Hot Plug Ultra
ATA/100 Hard Drives
ATA/100 Hard Drives
ATA/100 Hard DrivesATA/100 Hard Drives
40 GB 5.4 K
40 GB 5.4 K
40 GB 5.4 K40 GB 5.4 K
DA - 11686 Worldwide — Version 13 — October 8, 2004
Capacity
Capacity
CapacityCapacity
Height
Height
HeightHeight
Width
Width
WidthWidth
Interface
Interface
InterfaceInterface
Transfer Rate Synchronous
Transfer Rate Synchronous
Transfer Rate SynchronousTransfer Rate Synchronous
(Maximum)
Seek Time
Seek Time
Seek TimeSeek Time
(typical reads, including
settling)
Physical Configuration
Physical Configuration
Physical ConfigurationPhysical Configuration
40,007 MB
0.374 in (9.5 mm)
2.756 in (70 mm)
Ultra ATA-5 (IDE) 100 MB/s
27.8 to 44.1 MB/sec (Disk-Buffer)
Single Track
Rotational Speed
Bytes/Sector
Logical Blocks
13 ms
5,400 RPM
512
78,140,160 (LBA)
Page 21
QuickSpecs
Technical Specifications
Two NC3163 Fast
Two NC3163 Fast
Two NC3163 FastTwo NC3163 Fast
Ethernet NIC Embedded
Ethernet NIC Embedded
Ethernet NIC EmbeddedEthernet NIC Embedded
10/100 WOL
10/100 WOL
10/100 WOL10/100 WOL
HP ProLiant BL
HP ProLiant BL
HP ProLiant BLHP ProLiant BL
e-Class C-GbE
e-Class C-GbE
e-Class C-GbEe-Class C-GbE
Interconnect Switch
Interconnect Switch
Interconnect SwitchInterconnect Switch
(Wake on LAN)
Network Interface
Network Interface
Network InterfaceNetwork Interface
Compatibility
Compatibility
CompatibilityCompatibility
Data Transfer Method
Data Transfer Method
Data Transfer MethodData Transfer Method
Network Transfer Rate
Network Transfer Rate
Network Transfer RateNetwork Transfer Rate
Connector
Connector
ConnectorConnector
Cable Support
Cable Support
Cable SupportCable Support
General
General
GeneralGeneral
Performance
Performance
PerformancePerformance
Forwarding Mode
Forwarding Mode
Forwarding ModeForwarding Mode
MAC Addresses
MAC Addresses
MAC AddressesMAC Addresses
Memory
Memory
MemoryMemory
Ports
Ports
PortsPorts
Management
Management
ManagementManagement
IEEE Standards
IEEE Standards
IEEE StandardsIEEE Standards
Compliance
Compliance
ComplianceCompliance
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
Two 24-port Managed Layer 2 Ethernet switches for server network cable reduction
Fully pre-configured for immediate operation
4.0 Gbps Switching bandwidth
12 Million pps aggregate throughput (64-byte packets)
Full-wire speed for all connections
Store and forward
16,382; MAC address based filtering and MAC address packet priority configuring
64MB Main
12MB Flash
32MB Packet Buffer
Four RJ-45 10/100/1000 T/TX/T Gigabit Ethernet uplink ports for customer use
Forty 10/100 T/TX fast Ethernet downlink ports dedicated to server blade to interconnect
switch network connections
Two 10/100 T/TX Fast Ethernet ports dedicated to inter-switch module communications
One RS-232 DB-9 port (console connector for Integrated Administrator)
One 10/100 T/TX Fast Ethernet port (Network management connector for Integrated
Administrator)
Auto-negotiation and auto-sensing with full-duplex
Web-based interface with graphical user interface
Console menu driven Interface via local RS-232 and Telnet
Scriptable command line interface (CLI)
SNMP v1 (RFC 1157) with scripting tool and example scripts
RMON v1 (RFC 1757) groups 1, 2, 3, and 9
Telnet (RFC 854)
MIB-II (RFC 1213), Bridge MIB (RFC 1493), Interface MIB (RFC 2233), 801.1Q MIB (RFC
2684), RMON1 MIB (RFC 1757) groups 1, 2, 3, and 9, Ethernet MIB (RFC1643) and HPspecific switch MIBs
64 Port-based IEEE 802.1Q tagged VLANs per switch module
XML human read/write configuration file
TFTP client (RFC 783) for backup and remote download of configuration and history log
files
IGMP (Internet Group Management Protocol) multicasting
EtherChannel (Fast EtherChannel, GigaChannel) compatible trunking
Uplink port speed and link activity LEDs
Simple network time protocol (SNTP)
Broadcast, multicast, and DA-unknown packet storm control
BootP and DHCP client support
BootP and DHCP client support
Port mirroring
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Ethernet
IEEE 802.3ab 1000Base-T Ethernet
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1p Quality of Service (QoS) Packet Prioritization
IEEE 802.3ac and 802.1Q Port Based Tagged VLANs and VLAN Extensions
10 Mb/s
20 Mb/s
100 Mb/s
200 Mb/s
Categories 3, 4 or 5 UTP; up to 328 ft (100 m)
Category 5 UTP; up to 328 ft (100 m)
DA - 11686 Worldwide — Version 13 — October 8, 2004
Page 22
QuickSpecs
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server Blade
HP ProLiant BL10e Generation 2 (G2) Server BladeHP ProLiant BL10e Generation 2 (G2) Server Blade
Technical Specifications
IEEE 802.1Q Trunking Encapsulation
IEEE 802.3x Flow Control
The information contained herein is subject to change without notice.
Microsoft and Windows NT are US registered trademarks of Microsoft Corporation. Intel is a US registered trademark of Intel Corporation.
Removable interconnect tray that plugs into the rear of the server blade enclosure
10Base-T (Half-Duplex)
10Base-T (Full-Duplex)
100Base-TX (Half-Duplex)
100Base-TX (Full-Duplex)
1000Base-T (Full-Duplex)
1000Base-T (Full-Duplex)
10Base-T
100Base-TX
1000Base-T
10 Mb/s
20 Mb/s
100 Mb/s
200 Mb/s
2000 Mb/s
2000 Mb/s
Categories 3, 4 or 5 UTP;up to 328 ft (100 m)
Category 5 UTP; up to 328 ft (100 m)
Category 5 UTP; up to 328 ft (100 m)
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein
should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
DA - 11686 Worldwide — Version 13 — October 8, 2004
Page 23
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.