Copyright 1998 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be copied or distributed,
transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form
or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the
express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation
reserves the right to revise this publication and to make changes from time to time in the contents hereof without
obligation of Paradyne Corporation to notify any person of such revision or changes.
Changes and enhancements to the product and to the information herein will be documented and issued as a new
release to this manual.
Warranty, Sales, and Service Information
Contact your local sales representative, service representative, or distributor directly for any help needed. For
additional information concerning warranty , sales, service, repair , installation, documentation, training, distributor
locations, or Paradyne worldwide office locations, use one of the following methods:
Via the Internet: Visit the Paradyne World Wide W eb site at http://www.paradyne.com
Via Telephone: Call our automated call system to receive current information via fax or to speak with a
company representative.
— Within the U.S.A., call 1-800-870-2221
— Outside the U.S.A., call 1-727-530-2340
Trademarks
All products and services mentioned herein are the trademarks, service marks, registered trademarks or registered
service marks of their respective owners.
This guide describes how to install and use the COMSPHERE 6700 Series
Network Management System (NMS) Multiuser feature.
It is assumed that you have a basic understanding of modems and their
operation, are knowledgeable about data communications, and are familiar with
Windows terminology and conventions. You or your LAN administrator should
also have knowledge of TCP/IP.
Document Summary
SectionDescription
Chapter 1
Chapter 2
GlossaryRefer to
IndexLists key terms, acronyms, concepts, and sections in
Introduction.
features and network topologies.
Installation.
requirements and installation steps.
Management System User’s Guide,
Number 6700-A2-GY31.
alphabetical order.
Provides an introduction to the multiuser
Presents hardware and software
COMSPHERE 6700 Series Network
Document
6700-A2-GB21-20
February 1998
iii
About This Guide
Product-Related Documents
Document NumberDocument Title
3000-A2-GA31
3610-A2-GB46
3610-A2-GB48
3610-A2-GB49
3810-A2-GB30
3910-A2-GN32
6700-A2-GB20
6700-A2-GB22
6700-A2-GB23
COMSPHERE 3000 Series Carrier, Installation
Manual
COMSPHERE 3600 Series Data Service Units,
Models 3610 and 3611, User’s Guide
COMSPHERE 3600 Series Data Service Units,
Models 3610 and 3611, Time Division Multiplexer,
Multichannel Multipoint, and Digital Bridge Options
Supplement
COMSPHERE 3600 Series Data Service Units,
Models 3610 and 3611, Dial Backup Module Options
Supplement
COMSPHERE 3800 Series Modems, Models 3810,
3811, and 3820, User’s Guide
COMSPHERE 3900 Series Modems, Models 3910
and 3911, Point-to-Point/Multipoint, Installation and
Operation Manual
COMSPHERE 6700 Series Network Management
System SNMP Proxy Agent Feature User’s Guide
COMSPHERE 6700 Series Network Management
System Network Configuration Guide
COMSPHERE 6700 Series Network Management
System Remote Monitor Feature User’s Guide
6700-A2-GB41
6700-A2-GY31
Contact your sales or service representative to order additional product
documentation.
Paradyne documents are also available on the World Wide Web at:
http://www.paradyne.com
Select
Service & Support → Technical Manuals
COMSPHERE 6700 Series Network Management
System Security Manager Feature Supplement
COMSPHERE 6700 Series Network Management
System User’s Guide
iv
February 1998
6700-A2-GB21-20
About This Guide
Product-Related Documents
Document NumberDocument Title
3000-A2-GA31
3610-A2-GB46
3610-A2-GB48
3610-A2-GB49
3810-A2-GB30
3910-A2-GN32
6700-A2-GB20
6700-A2-GB22
6700-A2-GB23
COMSPHERE 3000 Series Carrier, Installation
Manual
COMSPHERE 3600 Series Data Service Units,
Models 3610 and 3611, User’s Guide
COMSPHERE 3600 Series Data Service Units,
Models 3610 and 3611, Time Division Multiplexer,
Multichannel Multipoint, and Digital Bridge Options
Supplement
COMSPHERE 3600 Series Data Service Units,
Models 3610 and 3611, Dial Backup Module Options
Supplement
COMSPHERE 3800 Series Modems, Models 3810,
3811, and 3820, User’s Guide
COMSPHERE 3900 Series Modems, Models 3910
and 3911, Point-to-Point/Multipoint, Installation and
Operation Manual
COMSPHERE 6700 Series Network Management
System SNMP Proxy Agent Feature User’s Guide
COMSPHERE 6700 Series Network Management
System Network Configuration Guide
COMSPHERE 6700 Series Network Management
System Remote Monitor Feature User’s Guide
6700-A2-GB41
6700-A2-GY31
Contact your sales or service representative to order additional product
documentation.
Paradyne documents are also available on the World Wide Web at:
http://www.paradyne.com
Select
Service & Support → Technical Manuals
COMSPHERE 6700 Series Network Management
System Security Manager Feature Supplement
COMSPHERE 6700 Series Network Management
System User’s Guide
iv
February 1998
6700-A2-GB21-20
Introduction
What is the Multiuser Feature?
The COMSPHERE 6700 Multiuser feature gives you the ability to connect
multiple Windows workstations together to form a network of NMS users. With
this feature, each user’s workstation has a complete graphical interface that
interacts with the NMS as if it were a single user workstation.
The Multiuser feature consists of two separately orderable packages: Server and
Client.
You can install the Multiuser Server and Client packages on the COMSPHERE
6700 Series NMS at any time.
1
Feature List
The Multiuser feature supports up to six simultaneous users. In addition, the
software provides statistical data and Platform/Network Performance Monitoring.
In addition to all the features of the 6700 Series NMS, the Multiuser feature
provides the following capabilities:
Integrated TCP/IP, UDP/IP, and SNMP
Concurrent Ethernet, Token Ring, FDDI, SLIP, and PPP interfaces
Support for various network adapter vendors
User-definable configuration via the COMSPHERE 6700 Series NMS
Network Configuration feature
Seamless multiuser (up to 6 users) via LAN and/or RS-232 connections via
SLIP and/or PPP
RS-232 Gateway to LAN via SLIP and/or PPP allowing dial-up multiuser
Full graphical user interface features at all multiuser workstations
Platform/Network Performance Monitoring
Knowledge of more than one NMS server
6700-A2-GB21-20
User-selectable active NMS server
February 1998
1-1
Introduction
Sample Multiuser Network Topologies
When using the Multiuser feature, one workstation must be configured as the
server
NMS
connected. The server is also the point of interface with all NMS devices.
where the NMS database resides and the control channels are
All other networked workstations must be configured as an NMS
executes only the user interface portion of the NMS.
Figures 1-1, 1-2, and 1-3 show some sample Multiuser feature network
topologies.
client
, which
1-2
Figure 1-1. Multiuser LAN Network
February 1998
6700-A2-GB21-20
Figure 1-2. Multiuser Serial Network (Using SLIP and/or PPP)
Introduction
6700-A2-GB21-20
Figure 1-3. Multiuser Serial Gateway or Ethernet Modem
(Using SLIP and/or PPP)
February 1998
1-3
Introduction
Multiuser Feature Package Contents
The Multiuser feature package includes the following:
Server:
Multiuser server software on one or more 3 1/2″ disks
One
One
Client:
Multiuser client software on one or more 3 1/2″ disks
One
One
COMSPHERE 6700 Series Network Management System Multiuser
Feature User’s Guide
COMSPHERE 6700 Series Network Management System Network
Configuration Guide
COMSPHERE 6700 Series Network Management System Multiuser
Feature User’s Guide
COMSPHERE 6700 Series Network Management System Network
Configuration Guide
1-4
February 1998
6700-A2-GB21-20
Installation
Hardware Requirements
The following are the hardware requirements for installation of the Multiuser
feature server and client software:
Server
486 processor, 66 MHz or higher PC (or compatible computer)
16 MB of RAM (32 MB of RAM recommended)
Hard disk with 15 MB of free space and a minimum of 14 ms access time
2
Super VGA (800 x 600 resolution) or higher with 256 colors
Video accelerator card
One of the following network interfaces:
— NDIS-compliant network adapter
— ODI network adapter
— Additional serial port
1 serial port for device communication
LAN adapter or additional serial port
1 parallel port for a printer
101 keyboard
Mouse
3.5″ 1.44 megabyte diskette drive
DB-25 socket to 6-pin (RJ11) socket adapter (Part #002-0025-0031)
6700-A2-GB21-20
February 1998
2-1
Installation
This configuration is sufficient for a network of 1–512 local and remote devices. If
the number of devices increases, use the following table as a guideline for
upgrading your hardware configuration:
486 processor, 66 MHz or higher PC (or compatible computer)
16 MB of RAM (32 MB of RAM recommended)
Hard disk with 15 MB of free space and a minimum of 14 ms access time
Super VGA (800 x 600 resolution) or higher with 256 colors
Video accelerator card
One of the following network interfaces:
— NDIS-compliant network adapter
— ODI network adapter
— Additional serial port
1 serial port for device communication
LAN adapter or additional serial port
1 parallel port for a printer
101 keyboard
Mouse
3.5″ 1.44 megabyte diskette drive
This configuration is sufficient for a network of 1–512 local and remote devices. If
the number of devices increases, use the following table as a guideline for
upgrading your hardware configuration:
To use the Multiuser feature on Ethernet, Token Ring, or FDDI, you must install a
supported network adapter board. Supported boards are listed in Table 2-1.
Table 2-1. Support Network Adapter Boards (1 of 2)
Installation
Interface
Ethernet
VendorModem
3COM3C501 Ether Link
3C503 Ether Link II
3C505 Ether Link Plus
3C507 Ether Link 16
3C509 Ether Link III
3C523 Ether Link/MC TP
3C527 Ether Link/MC 32
Allied TelesisA T-1500 Network Adapter
Hewlett-PackardHP27247/HP27252 Plus
IntelEtherExpress 16 and 16T
Novell/ExcelanEXOS105T
NE1000
NE2000
Racal InterLanNI5210
NI6510
SMCSMC 8000
SMC Elite 16
6700-A2-GB21-20
Ungermann-Bass
Western DigitalEtherCard Plus
XircomAll PE Models
Other(NDIS Driver Required)
February 1998
Networth EtherNext 16-Bit UTP
NIUpc/EOTP
NIUps
EtherCard Plus Elite 16
All PE2 Models
All PE3 Models
2-3
Installation
Table 2-1. Support Network Adapter Boards (2 of 2)
Raycone16/4 Token Ring Adapter
Other(NDIS Driver Required)
Software and Installation Requirements
You must have one of the following sets of software installed before you install
the Multiuser feature server or client software:
COMSPHERE 6700 Series NMS Release 5.0.0 or higher with Microsoft
Windows 95 or Windows NT, or
p189X
p1990
COMSPHERE 6700 Series NMS Release 4.0.0 or higher with Microsoft
Windows 3.1.
Additional network installation requirements are based on the software installed:
With COMSPHERE 6700 Series NMS Release 5.0.0 or higher, it is expected
that the user has installed the TCP/IP stack and has a functioning network.
With COMSPHERE 6700 Series NMS Release 4.0.0 or higher, NetManage
software is supplied to meet licensing requirements. Do not separately install
the NetManage software. During the
Installing the Multiuser Feature
procedure, the NetManage software is installed automatically.
2-4
February 1998
6700-A2-GB21-20
Installation Worksheet
Before installing and configuring the Multiuser feature, you need some system
and network information. Use the following form to collect the necessary
information before you start the installation process. Retain this form as a record
of this information. Examples are shown in brackets [ ].
Installation
Multiuser Feature Installation and Configuration Information
General
Where to install the software [c:\pcnms]:
Location of network drivers [c:\pcnms]:
Software Serial Number [149301]:
Software Key Number [dkjslmo]:
Network Interface Name [Ethernet0]:
Network Interface Type [Ethernet]:
Multiuser Workstation
Internet Address of Workstation [192.0.2.2]:
Unique Node Name [Largo Bldg. H]:
NMS Server(s) Name [6700 Bldg. H]:
NMS Server(s) IP Address [192.0.2.1]:
LAN/Hardware Interface
Adapter Vendor Name [Western Digital]:
Board Type [Ether Card Plus]:
Interrupt Level [5]:
I/O Base Address [0x300]:
SLIP Interface
Baud Rate [9600):
Flow Control (Hardware]:
Modem Type [Hayes compatible]:
Port [COM 1]:
Telephone Number [9,1,813-530-2671]:
Optional
Subnet Mask [255.255.255.0]:
6700-A2-GB21-20
Default Gateway [192.0.2.254]:
February 1998
2-5
Installation
Installing the Multiuser Feature
To install the Multiuser feature server or client software, start from the Program
Manager window.
NOTE:
NMS is designed to be the primary application program running on a
personal computer. If you use NMS with other applications, it is your
responsibility to ensure compatibility.
Procedure
1. Insert Disk #1 into Drive A.
2. From the Program Manager window, choose File.
3. From the File menu, choose Run.
4. In the Command Line field, type A:\INSTALL.
5. Choose OK. The Welcome window appears.
2-6
6. Choose Continue. The Product Information window appears.
February 1998
6700-A2-GB21-20
Installation
7. Choose Yes. The Destination Directory window appears.
The Destination Directory window allows you to place the NMS software into
a specific directory. A single directory within a single partition is required.
8. Enter a subdirectory location or choose the default setting of C:\PCNMS.
9. Choose Continue. The Confirmation window appears.
6700-A2-GB21-20
10. Choose Install to confirm the installation of the NMS software into the
specified directory. The Completion status window appears.
February 1998
2-7
Installation
This window displays a bar indicating the percentage of completion for the
current installation. In addition, the names of the files being installed appear
above the bar until the installation is complete. The Installation Completed!
window appears.
11. Choose OK to return to Windows.
12. To start NMS, choose the NMS icon from the COMSPHERE 6700 Program
Group window.
Configuring the Multiuser Feature
After installation, use the Network Configuration application option to customize
your configuration for TCP/IP networks if not already configured. For details on
doing so, refer to the