HP 366T User Manual

Page 1
HP Ethernet 1Gb 4-port 366T Adapter
Abstract
This document is for the person who installs, administers, and troubleshoots servers and storage systems. HP assumes you are qualified in the servicing of computer equipment and trained in
Part Number: 826574-001 September 2015 Edition: 1
User Guide
recognizing hazards in products with hazardous energy levels.
Page 2
© Copyright 2015 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Microsoft® and Windows® are trademarks of the Microsoft group of companies. Intel® is a trademark of Intel Corporation in the U.S. and other countries.
Page 3
Contents
Technician notes ........................................................................................................................... 4
Warnings, cautions, and notes .................................................................................................................... 4
Downloading files ..................................................................................................................................... 4
Introduction .................................................................................................................................. 6
Overview ................................................................................................................................................. 6
LED indicators ........................................................................................................................................... 6
Installing an adapter ..................................................................................................................... 8
Installation overview .................................................................................................................................. 8
Preventing electrostatic discharge ................................................................................................................ 8
Installing an adapter in a server .................................................................................................................. 9
Installing a low profile bracket .................................................................................................................... 9
Connecting the network cable ................................................................................................................... 10
Specifications ............................................................................................................................. 11
UTP cable specifications ........................................................................................................................... 11
General specifications ............................................................................................................................. 11
Compliance ............................................................................................................................................ 11
Power and environmental specifications ..................................................................................................... 12
Regulatory compliance notices ..................................................................................................... 13
Federal Communications Commission notice ............................................................................................... 13
Modifications .......................................................................................................................................... 13
European Union regulatory notice ............................................................................................................. 13
Canadian notice (Avis Canadien) .............................................................................................................. 14
Korean class A notice .............................................................................................................................. 14
Japanese class A notice ........................................................................................................................... 14
Disposal of waste equipment by users in private households in the European Union ......................................... 14
Electrostatic discharge ................................................................................................................. 15
Preventing electrostatic discharge .............................................................................................................. 15
Grounding methods to prevent electrostatic discharge .................................................................................. 15
Support and other resources ........................................................................................................ 16
Before you contact HP .............................................................................................................................. 16
HP contact information ............................................................................................................................. 16
Acronyms and abbreviations ........................................................................................................ 17
Documentation feedback ............................................................................................................. 18
Contents 3
Page 4
Technician notes
level
Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
component. If this surface is
To reduce the risk of injury from a hot component, allow the surface to cool
Warnings, cautions, and notes
WARNING: Only authorized technicians trained by HP should attempt to repair this equipment.
All troubleshooting and repair procedures are detailed to allow only subassembly/module­repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard.
WARNING: To reduce the risk of electric shock, personal injury, and damage to the equipment:
Do not attempt to service any parts of the equipment other than those specified in the following
procedure. Any other activities may require that you shut down the server and remove the power cord.
Installation and maintenance of this product must be performed by individuals who are
knowledgeable about the procedures, precautions and hazards associated with the product.
WARNING: To reduce the risk of electric shock or damage to the equipment:
Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
times.
Unplug the power cord from the power supply to disconnect power to the equipment.
Do not route the power cord where it can be walked on or pinched by items placed against it.
Pay particular attention to the plug, electrical outlet, and the point where the cord extends from the server.
This symbol indicates the presence of a hot surface or hot contacted, the potential for injury exists.
WARNING:
before touching.
CAUTION: To properly ventilate the system, you must provide at least 7.6 cm (3.0 in) of
clearance at the front and back of the server.
CAUTION: The server is designed to be electrically grounded (earthed). To ensure proper
operation, plug the AC power cord into a properly grounded AC outlet only.
NOTE: Any indications of component replacement or printed wiring board modifications may
void any warranty.
Downloading files
1. Go to the HP website (http://www.hp.com/#Support).
Technician notes 4
Page 5
Select Download drivers and software (and firmware).
2.
3. Type the adapter name in the For product box and then click Go. For example, type HP Ethernet 1Gb
4-port 366T.
4. Download the drivers, firmware, or documentation as needed.
Technician notes 5
Page 6
Introduction
1
Activity
Off
Indicates no network activity on the link.
Flashing (Green)
Indicates network activity on the link. The adapter is
Link
Off
No link to the adapter is established. The adapter is not Off
Link to the adapter is established at 10 Mb/s.
On (Green)
Link to the adapter is established at 100 Mb/s. The
Overview
The HP Ethernet 1Gb 4-port 366T Adapter is a four port, 1 Gb 10/100/1000BASE-T Ethernet adapter. The HP Ethernet 1Gb 4-port 366T Adapter is field replaceable and features Energy Efficient Ethernet and IEEE 1588/Precision Time Protocol support, PCI Express v2.0, and a sea of sensors that allows temperature monitoring of the option for optimized server power consumption.
For more information about the HP Ethernet 1Gb 4-port 366T Adapter, see the HP website
LED indicators
(http://www.hp.com/go/proliantnics).
The HP Ethernet 1Gb 4-port 366T Adapter has four ports with LED indicators for Link (L) and Activity (A) for each port. A standard-height bracket is shown in the following figure with RJ-45 ports and LED indicators.
The HP Ethernet 1Gb 4-port 366T Adapter LED indicators operate as described in the following table.
Item LED indicator Status Description
2
sending or receiving network data at up to 1 Gb/s.
receiving power or the cable connection is faulty.
adapter is receiving power and the cable connection is good.
Introduction 6
Page 7
Item LED indicator Status Description
On (Amber/Orange)
Link to the adapter is established at 1 Gb/s. The
adapter is receiving power and the cable connection is good.
Introduction 7
Page 8
Installing an adapter
To reduce the risk of personal injury or damage to the equipment, consult the safety
Some servers contain high energy circuits, high current circuits, moving parts (such as fan blades),
serviced only by qualified personnel who have been trained to deal with these hazards. Do not
X, and PCI Express devices.
Installation overview
This section describes installation precautions, how to install the adapter, and how to connect the network cable.
WARNING:
information and user documentation provided with the server before attempting the installation.
or any combination of these hazards, that may be exposed if covers and access panels are removed while the product is connected to a power source. These products are intended to be
remove enclosures or attempt to bypass any interlocks designed to guard against these hazardous conditions.
WARNING: Installation of this adapter should be performed by individuals who are both
qualified in the servicing of computer equipment, and trained in the hazards associated with products capable of producing hazardous energy levels. This adapter is intended to be installed in Certified (UL or CSA) ITE equipment having instructions for adding and removing user installed components such as PCI, PCI­Refer to the equipment instructions to verify that it is suitable for user installed components and that it has the power capacity to support all of the installed components.
NOTE: Before removing the cover of your server, refer to the HP documentation for the proper
methods for installing a PCI Express card and avoiding electric shock hazards.
Preventing electrostatic discharge
To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
To prevent electrostatic damage:
Avoid hand contact by transporting and storing products in static-safe containers.
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
Place parts on a grounded surface before removing them from their containers.
Avoid touching pins, leads, or circuitry.
Always be properly grounded when touching a static-sensitive component or assembly.
Installing an adapter 8
Page 9
Installing an adapter in a server
wn and disconnect the power
cord from the power outlet before removing the server access panel. Failure to do so may damage
To reduce the risk of personal injury from a hot component, allow the surface of the
For additional information on how to safely install a PCI Express card in the server, see the HP ProLiant server documentation.
CAUTION: If the server is not PCI Hot Plug compliant, power it do
the adapter or server.
1. Power down the server.
2. Remove the power cord and server access panel.
WARNING:
option card to cool before touching it.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
3. Identify the PCI Express option slot in which the adapter is to be installed. If a low profile option slot is
to be used, install the low profile bracket onto the adapter.
4. Remove the cover bracket from the PCI Express slot.
5. Firmly seat the adapter in the PCI Express slot and secure the adapter bracket.
NOTE: For 1U type servers you may need to replace the standard profile bracket with a low
profile bracket. See "Installing a low profile bracket (on page 9)."
6. Replace the access panel and plug in the power cord.
Installing a low profile bracket
You may have to install a low profile bracket to complete the product installation. The low profile bracket replaces the existing standard profile bracket shipped on the product.
To install a low profile bracket:
Installing an adapter 9
Page 10
Using a correctly sized slotted screwdriver, carefully remove the two board lock screws located at the
1.
top and bottom of the connector.
2. Remove the standard profile bracket and place the low profile bracket over the connector. Be careful
not to damage the connector or bind the low profile bracket to the connector.
Connecting the network cable
To secure the cable, plug the cable connector into the RJ-45 port. Ensure that the tab on the plug clicks into position indicating that it is properly seated.
For more information, see "UTP cable specifications (on page 11)".
Installing an adapter 10
Page 11
Specifications
Controller
Intel I350
Data rate
1 Gb/s per port, 2 Gb/s combined, full-duplex
PCI bus
PCI Express x4 Gen2
Connectors
2 RJ-45
Dimensions (LxW)
13.4 cm x 5.6 cm (5.3 x 2.2 inches) without bracket
IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.3ad, IEEE802.1p,
UL Mark (US and Canada)
PCIe v2.0
UTP cable specifications
The HP Ethernet 1Gb 4-port 366T adapter can use existing UTP CAT5 (or better) cable to deliver Gigabit Ethernet over copper, according to the IEEE 802.3ab specifications. For new installations, CAT5e (enhanced CAT5) cable is recommended.
Maximum distances for Gigabit over copper cable are 100 meters (328 feet).
To connect to the network, the HP Ethernet 1Gb 4-port 366T uses the following cable for 1000Base-T transmission:
CAT5 UTP or better twisted-pair
22-26 AWG, 100 @ 1 MHz
EIA/TIA 568a or EIA/TIA 568b
General specifications
Specification Value
Compliance
Compliance Standard
IEEE
Safety
Other
IEEE802.1q,IEEE1588
EN 60950
RoHS 6 of 6 IPv4, IPv6 CE Microsoft Windows Hardware Quality Labs Server Design Guide version 3.0 SNMP IPv4, TCP and UDP Checksum Offload IPv4/IPv6 TCP, Large Send Offload Receive-Side Scaling Jumbo Frames up to 9.5 KBytes
Specifications 11
Page 12
Temperature—0° to 55° C (0° to 131° F)
Temperature—40° to 70° C (0° to 158° F) Power
4 W typical, 5 W maximum
Power and environmental specifications
Specification Value
Operating
Non-operating
Humidity—15 to 80% relative humidity, non-condensing
Humidity—10 to 90% relative humidity, non-condensing
Specifications 12
Page 13
Regulatory compliance notices
Federal Communications Commission notice
Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules. These rules place computers and related peripheral devices into two classes, A and B, depending upon their intended installation. Class A devices are those that may reasonably be expected to be installed in a business or commercial environment. Class B devices are those that may reasonably be expected to be installed in a residential environment (for example, personal computers). The FCC requires devices in both classes to bear a label indicating the interference potential of the device as well as additional
Modifications
operating instructions for the user.
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment.
European Union regulatory notice
Products bearing the CE marking comply with one or more of the following EU Directives, as may be applicable:
Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC
Ecodesign Directive 2009/125/EC
R&TTE Directive 1999/5/EC
RoHS Directive 2011/65/EU
Compliance with these directives is assessed using applicable European Harmonised Standards.
The full Declaration of Conformity can be found at the following HP website (http://www.hp.eu/certificates). (Search with the product model name or its Regulatory Model Number (RMN), which may be found on the regulatory label.)
The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS: HQ-TRE, Herrenberger
Strasse 140, 71034 Boeblingen, GERMANY.
Regulatory compliance notices 13
Page 14
Canadian notice (Avis Canadien)
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations, CAN ICES-3(A)/NMB-3(A).
Cet appareil numérique de la class A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Korean class A notice
Japanese class A notice
Disposal of waste equipment by users in private households in the European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Regulatory compliance notices 14
Page 15
Electrostatic discharge
Preventing electrostatic discharge
To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
To prevent electrostatic damage:
Avoid hand contact by transporting and storing products in static-safe containers.
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
Place parts on a grounded surface before removing them from their containers.
Avoid touching pins, leads, or circuitry.
Always be properly grounded when touching a static-sensitive component or assembly.
Grounding methods to prevent electrostatic discharge
Several methods are used for grounding. Use one or more of the following methods when handling or installing electrostatic-sensitive parts:
Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist
straps are flexible straps with a minimum of 1 megohm ±10 percent resistance in the ground cords. To provide proper ground, wear the strap snug against the skin.
Use heel straps, toe straps, or boot straps at standing workstations. Wear the straps on both feet when
standing on conductive floors or dissipating floor mats.
Use conductive field service tools.
Use a portable field service kit with a folding static-dissipating work mat.
If you do not have any of the suggested equipment for proper grounding, have an authorized reseller install the part.
For more information on static electricity or assistance with product installation, contact an authorized reseller.
Electrostatic discharge 15
Page 16
Support and other resources
Before you contact HP
Be sure to have the following information available before you call HP:
Active Health System log (HP ProLiant Gen8 or later products)
Download and have available an Active Health System log for 7 days before the failure was detected. For more information, see the HP iLO 4 User Guide or HP Intelligent Provisioning User Guide on the HP website (http://www.hp.com/go/ilo/docs).
Onboard Administrator SHOW ALL report (for HP BladeSystem products only)
For more information on obtaining the Onboard Administrator SHOW ALL report, see the HP website (http://www.hp.com/go/OAlog).
Technical support registration number (if applicable)
Product serial number
Product model name and number
Product identification number
Applicable error messages
Add-on boards or hardware
Third-party hardware or software
Operating system type and revision level
HP contact information
For United States and worldwide contact information, see the Contact HP website (http://www.hp.com/go/assistance).
In the United States:
To contact HP by phone, call 1-800-334-5144. For continuous quality improvement, calls may be
recorded or monitored.
If you have purchased a Care Pack (service upgrade), see the Support & Drivers website
(http://www8.hp.com/us/en/support-drivers.html). If the problem cannot be resolved at the website, call 1-800-633-3600. For more information about Care Packs, see the HP website (http://pro-aq-sama.houston.hp.com/services/cache/10950-0-0-225-121.html).
Support and other resources 16
Page 17
Acronyms and abbreviations
CSA
Canadian Standards Association
IPv4
Internet Protocol version 4
IPv6
Internet Protocol version 6
PCI-X
peripheral component interconnect extended
UTP
unshielded twisted pair
Acronyms and abbreviations 17
Page 18
Documentation feedback
HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (mailto:docsfeedback@hp.com). Include the document title and part number, version number, or the URL when submitting your feedback.
Documentation feedback 18
Loading...