HP 3586 schematic

A PRACTICAL GUIDE FOR USING THE HP3586A/B/C SELECTIVE

LEVEL METER©

(Version 2.0), September 2004

By Bill Feldmann, N6PY

1

TABLE OF CONTENTS

CHAPTER PAGE

1 Introduction 3
2 Description of the HP3586 4
3 Signal Connections 7
4 Front Panel Description and Initial Setup 8
5 Setting and Measuring Frequency 11
6 Power Level Measurements Using the Selective Mode 13
7 Voltage Level Measurements Using the Selective Mode 15
8 Measuring Carrier Signal Strength 16
9 Tuning SSB Signals Using the Selective Mode 17
10 Tuning SSB Signals Using the Noise/Demodulation Mode 19
11 Measuring Audio Noise Using the Wideband Mode 20
12 Measuring Impulse Noise 21
13 Measuring Harmonic Audio Harmonic Distortion 22
14 Passive and Active Network Analysis 24
15 Measuring a Transmitter’s Spurious Emissions 26
16 Selection of Measurement Modes and Other Considerations 28

Appendix A Understanding the Decibel Level Measuring System 31
Appendix B HP3586 Error Codes 34
Appendix C Schematics of Useful HP3586 Accessories 35

2

1. INTRODUCTION

This documents is intended for those having a HP3586 without the operator’s manual or are having trouble
understanding the operator’s manual and want to learn how to use this versatile instrument. It should also
be of use to those considering purchasing one of these instruments. This document is not intended as a
complete operating manual but should help you understand what it does and how to use it. This document
is written in a tutorial manner with many simple examples of typical measurements. If you want a copy of
the HP operator’s or service manuals, I highly recommend obtaining copies from Manuals Plus at 801-936­7000 where I obtained a professional quality copy of the operator’s manual at a reasonable price.

The HP 3586 family of Selective Level Meters was designed for the measurement of low power or voltage
levels on telephone lines carrying multiplexed single side band radio frequency signals along with lower
frequency audio signals. It’s designed to test and troubleshoot parameters commonly found on these lines.
This instrument is a very sensitive, selective and accurately calibrated receiver that’s also capable of
outputting a very low distortion signal of 0dbm at exactly the frequency it’s tuned to.

A while back I obtained a HP3586B that had been surplused from GTE from a couple of friends. They had
found a number of these for a reasonable price at a surplus electronic warehouse, they obtained all they
could and refurbished them, and then passed them on at their cost. Most had bad or leaking internal
batteries, which they removed. They also installed the more common BNC female input connectors in
place of the less common telephone connectors. Like all of these instruments on the surplus market mine
came without operating or service documentation. But I figured out how to use it to measure frequency,
use as an outboard VFO to drive my BC-610 AM transmitter, and as a receiver to search the radio bands
for interesting signals. I felt this was a very large and heavy, 60lb, instrument to do what some cheap Radio
Shack rice boxes could do and would take less room on my workbench. Also its internal receiver seemed
to have rather poor audio quality. However, after obtaining and studying a copy of the operator’s manual
and becoming more familiar with my HP3586B, a light went on in my head. I realized it’s a very versatile
and useful instrument and I wasn’t even using 10% of its capability.

Please, first read this document sequentially to best learn about your HP3586 since each chapter will build
on the experience you gain in previous chapters. We’ll start off describing the instrument so you’ll know
how it works, what it can measure, then learn how to control and set it up by discussing it’s front panel
along with its inputs and outputs, and finally learn how to use it for conducting useful measurements using
hands on type examples.

Feel free pass on copies of this document to others that may find it useful. I’ll publish revised versions as I
learn more about my HP3586 and discover new applications. I recommend you print out this document
and the schematics in Appendix C, place it in a binder and add any additional notes you may wish just after
the Appendix. Please don’t revise the document, just send me any suggested changes or additions at
[e-mail] and I’ll include them in future versions. Otherwise there will be different versions in
circulation with no revision control causing mass confusion for those attempting to use it. I’m also
releasing it in the Adobe PDF format to discourage uncontrolled changes and for easy Internet
downloading so I don’t have to get into the book printing and binding business. I copyrighted this
document to further control it and keep it’s use free of charge by using the © symbol on the document’s
title.

This document is dedicated to all those amateur radio operators that enjoy working on electronic circuits,
measure the performance of radios, repairing their radios, measuring audio through HF radio signals, or
restoring amateur or military radios that are keeping the hobby of amateur radio alive, well and interesting.
So read on and I hope you enjoy learning about the wonderful world of the HP3586.

3

2. DESCRIPTION OF THE HP3586

2.1 General – For those not familiar with selective level meters they can best be visualized as a receiver

having very high selectivity with a detector system capable of accurately measuring low power signal
levels from +20dbm down to –100dbm and frequency over a wide range from 200Hz to 32MHz and. It
also will output a signal of 0dbm, one miliwatt, at exactly the same frequency that the instrument is tuned
to, which is usually the center frequency of the selected receiver band pass filter. It’s also a SSB receiver
to aid in tuning the signal to be measured. Because of these features a selective level meter is extremely
valuable for measuring and the analysis of audio up through RF signals, it’s a whole lab of instruments in
one package. Because of this it can be used to measure the performance of electronic radio and RF
circuits, measure the strength and frequency of radio signals along with driving other electronic devices
using it’s one miliwatt low distortion output signal as a low power signal generator.

The HP3586 family of selective level meters was designed to measures signal levels and frequency in
selected portions of its total frequency spectrum on multiplex telephone transmission lines. These
frequency slices can be operator set by selection of filters from 20 Hz up to 3100 Hz in bandwidth that are
front panel selectable. All versions will have 20 and 400 Hz filters. The A and B versions have one
additional 1740 or 2000 Hz filter depending on model. Those with 003 option will have a 3100Hz filter
and a noise weighting WTD filter that can be switched in series with the 3100Hz filter to reduce low and
high audio frequency noise. The C version only has the 3100Hz filter without a WTD noise filter and no
filter options.

There are three versions of this family of instruments. The A and B versions have modes and features
making it easier to measure SSB channels on phone lines. The C version is more basic and doesn’t have
the SSB channel features of the A and B versions. However all three will work equally well for most of
the RF and audio measurement described in this document.

In its measuring modes except wideband the instrument will display and output a 0 dbm signal to a rear
panel connector at the center frequency its filter from an internal tracking oscillator. This signal’s
frequency can be set using the front panel keyboard or tuning knob. It also has a counter system that can
be commanded to read and display the frequency of the strongest steady signal within its filter’s pass band.
It can then be commanded to store this frequency in its frequency register changing its center frequency to
the register’s frequency and outputting this new frequency to its rear panel Fo connector. This feature is
very useful for measuring the frequency of a carrier and then synchronizing the frequency of another
device to that frequency. The instrument also contains a SSB detector system that is used to receive and
tune SSB signals or other signals into the instruments pass band.

In the following chapters I’ll describe how to setup your HP3586 to do useful measurements of frequency,
power, voltage, network analysis, distortion analysis, and use it on the air as an accurate signal strength
meter along with using it as a VFO to control an AM transmitter. In the interest of keeping things simple,
instrument features and modes that I feel are not useful for RF or audio measurements will not be discussed
in this document.

2.2 Instrument Capabilities - Since the HP3586 measures the total power of all signals in its filter’s

pass band, its always best to use the narrowest possible filter when measuring narrow band signals to
reduce noise errors. Power measurements are usually displayed in db’s referenced to o ne miliwatt, dbm
units, but can also be referenced to a pico watt, which I haven’t found useful. It can also measure the
voltage of a signal in db’s referenced to .775 volts on all versions and 1 volt on the C version. These units
may seem cumbersome since most of us prefer dealing with linear measurements in watts and volts, but it’s
better suited for measuring over very large ranges and is a standard method for those working with
telecommunications systems. If you are not familiar with this system of measurement or a little hazy on
understanding it, please take a look at Appendix A for a better understanding. You can easily convert to
watts or volts from the HP3586 panel readings by using the following formulas and a hand held calculator:

4

Power dbm = 10 log (Power in watts/.001) or Power watts = .001 [ anti log ( power dbm/10) ]

Voltage dbv = 20 log (Voltage volts/Vr) or Voltage volts = Vr [anti log (Voltage volts/20)]

Vr = .775 volts for the A and B models: Vr = 1 volts or .775 volts can be selected on the C model.

For optimum accuracy the instrument takes measurements over a small part of it’s total –120dbm to
+20dbm measuring range by using a range selectable detector circuit. The selectable ranges are, 100db
and 10db and have resolutions of .1db and .01db respectively. The readings are accurate over the whole
10db range but are only accurate over the upper 80db of the 100db range. The location of a range within
the instruments total measuring range is operator or automatically selected for best level measurement
accuracy. This is done by using an IF amplifier circuit whose gain is accurately changed. The IF amp is
located just before the detector and changes its gain to select the upper limit for the range of values the
detector is measuring. Specifying an upper limit for a range using the entry command actually selects the
gain of the IF amplifier. Automatic limit selection is done using a circuit similar to the AGC circuit in a
radio receiver.

One important point to remember is that the upper limit for the 100db range can not be set below –45dbm
because –80db below this setting starts to equal the instrument’s noise floor of around –120dbm. When the
detector is set to the 10db range the upper limit can be set much lower to –120dbm. The SSB demodulator
receives its signal from the IF strip in parallel with the level detector and will only be able to demodulate
signals above –55dbm. When the instrument is in the 100db range the gain of the IF strip is too low to
read radio signals below this level. Therefore, when using the SSB detector for audio tuning of received
radio signals we should almost always have the instrument in the 10db range since these radio signals are
usually below –55dbm. In chapter 4 we’ll show how to work around this problem when receiving SSB
signals.

For those of us working on electronic circuits or taking radio signal measurements this instrument is a
valuable tool that can be used to measure RF or audio noise, the frequency of a received carrier, find and
measure spurious transmitter signals, provide a signal and detector system for circuit analysis, and as a
VFO to control the carrier of a transmitter. It will work as a SSB receiver over its whole frequency range
to tune on the air signals for measurement. It receives and accurately measures signals down to -100dbm,
which is much lower than the noise on most ham bands.

One disadvantage when receiving SSB signals is that the HP3586 will not output the actual carrier
frequency of a SSB signal to its rear panel Fo output when using the SSB detector. It only outputs the
center frequency of the selected band pass. In this document I will describe how to work around this
problem when controlling AM transmitters.

2.3 Instrument Accuracy - The instrument uses 100db or 10db changeable ranges for maximum

accuracy as described above. The 100db range is only accurate over its upper 80db portion and has a
resolution of .1db. In the automatic range limit control mode the 100db range will have its upper limit
automatically changed to always stay within the accurate upper 80db part of this range. The narrower
range of 10db has a resolution of .01db. The instrument’s level measuring frequency range is 200Hz to
32MHz with a frequency resolution of .1Hz and accuracy of + or - .000001 of it’s reading during the first
year after calibration. The 004 optional crystal frequency reference was offered for greater frequency
display accuracy, see Chapter 16, section 16.8 if your instrument doesn’t have this option.

The instrument is intended for accurate measurements only in the range of –100dbm up to +20dbm. Using
the 50 or 75 ohm input from 200Hz to 32MHz and for signal levels between +20dbm and –80dbm,
between –80db and –100db its accuracy is +/- .75dbm. From 200Hz to 200KHz and from +20dbm to –
80dbm its level accuracy drops to +/-.40dbm, and from –80dbm to –100dbm it’s +/-.95dbm. Below
100dbm it’s accuracy isn’t rated and level measurements below –100dbm should not be trusted even
though the instrument will appear to read down to its noise floor of around –120dbm. By using

5

comparative measurement between different devices or conditions its accuracy can approach the 100db or
10db ranges precision of .1db or .01db, we’ll talk about that in Chapter 16.

To maintain accuracy the HP3586 does a 3 second duration automatic calibration, auto cal, when it’s first
turned on, every two minutes during operation, if its frequency is changed more than 1MHz, and when a
new measuring range width is selected. If any problems arise during calibration or during its operation the
display will output error codes, which are described in Append B. For special reasons su ch as SSB audio
tuning discussed in this document, the auto cal feature can be turned off at any time after its initial power
up.

2.4 The 004 Option – When I purchased my HP3586B I assumed it didn’t have the 004 enhanced

frequency accuracy option but I noticed a 004 installed sticker on its back panel. Also there was an oven
output connector installed on its back panel but no jumper from this connector to the external reference
connector just to its right. I then removed the instrument’s top cover by loosening a screw in the back of
the cover and sliding the cover off. To my delight I found a wire from the oven connector to a module
labeled A16 installed to the RH rear of the instrument’s motherboard, which was the 004 option module
with the 10 MHz crystal standard in a oven.

When I connected a jumper between these two connectors the oven light on my front panel came on for
about 10 minutes and then went off. After the oven light went out indicating the crystal oven was up to
temperature, checked WWV on 10 MHz using the counter procedure in section 5.3 of chapter 5 and found
my instrument was within .7 cycles of 10 MHz when using the counter on WWV’s 10 MHz carrier.
Without the jumper installed between the connectors, it was off by over 9 cycles so activating the 004
option made a great difference in the frequency accuracy of my instrument.

If the oven connector is installed on the back panel of your instrument but isn’t connected to the EXT REF
connector to its right, look inside your instrument and maybe you will be lucky and have this valuable
option. If your instrument has the A16 module installed, you must connect a jumper cable with two BNC
male connectors to activate the option.

2.5 Level Measuring Modes – The HP3586 family of instruments has the following modes for

measuring signal levels:

SELECTIVE See Chapters 4, 5, 6, 7 and 9
CARRIER See Chapter 8
NOISE/DEMODULATION See Chapter 10
WIDEBAND See Chapter 11
IMPULSE See Chapter 12
NETWORK ANALYSIS See Chapter 14
TONE Not Applicable
JITTER Not Applicable

I have found the first six measurement modes useful for radio and audio measurements. The other modes
are not normally useful because they are designed specifically for telephone measurements or require other
not normally available specialized equipment.

All measurement modes discussed in this document apply to the A and B versions where the
noise/demodulation, impulse and carrier modes are not available on the HP3586C general purpose version.
However, I’ll show how to make noise/demodulation measurements with the selective mode using the C
version.

6

3. SIGNAL CONNECTIONS

3.1 General - In this section I’ll describe how to connect a HP3586 for measuring frequency and power

level in the selective modes. In the following chapters I’ll also describe any differences for other
measurement modes.

3.2 Signal Input and Termination – Never put more than +27dbm or .5 watts total power into the

input 50 or 75 ohm connector of a HP3586 when using the internal termination. Never put more
than an AC + DC total of +42 volts into an unterminated connector.

To get a signal into a HP3586 you have the choice of many different input connectors and impedances.
However the only input I’ve found useful is the 75 or 50 ohm unbalanced input. All other inputs,
including the 600 ohm one, are not useful over the complete frequency range of the HP3586 and terminate
in impedances usually used for telephone circuits but not for RF circuits. The 75 or 50 ohm input is usable
over the instruments complete frequency range. Those with a HP3586C are fortunate that it has a 50 ohms
input. A or B versions only have a 75 ohm input. Most of the surplus instruments have telephone type
input connectors but many of us have converted ours to a more standard BNC connector for radio use. The
A and B version make all their power calculations based on 75 ohms even if the input is unterminated or
has an external 50 ohm termination resistor. However you can enter an offset to compensate for this
difference, more on this in section 6.2 of Chapter 6.

When making on the air measurements to a 50 ohm unterminated antenna line, use the 50 ohm termination
option on a C version or use a 50 ohm terminating resistor on the A and B versions and use the 10K 50pf
unterminated 75 ohm input. When measuring antenna signals in parallel with a receiver having a
terminated 50 ohm input, just simply hook a short 50 ohm feed line to the receiver’s antenna terminal in
parallel with the receivers antenna input and use the unterminated input option on all models of the HP-

3586.

When making measurements on RF circuits you can terminate the input with 50 or 75 ohms termination,
but on many circuits you may want to use the higher 10K 50pf unterminated input. Unfortunately this is
not very high for some tuned circuits and the 50pf may detune the circuit causing measurement errors. HP
did at one time offer accessory probes to isolate these circuits however they are not easy to obtain today so
consider a link coupling if only measuring frequency. For accurate level measurements you may want to
consider building a FET source follower or tube cathode follower one to one isolation amplifier to isolate
these circuits from the instrument’s input. I’ve shown two suggested circuits for this in Appendix C.

3.3 Tracking Oscillator’s Output Signal - This output signal can drive a transmitter or other device,

connect a BNC male connector with a 75 ohm line from the driven device’s input to the Fo output
connector located on the back panel. This outputs power is 0dbm or .27 volts RMS, which may not drive
many older tube type transmitters. It will drive my Viking 2 on 160 through 40 meters but not above these
bands and also is too low in power to drive my BC-610 through its crystal socket. I’ve constructed a small
solid state broad band amplifier to drive the BC-610 and my Viking 2 that boosts the output to at least 10
volts RMS for more drive and better isolation, its schematic is shown in Appendix C. Th is amplifier is in a
RF sealed box and mounted to the back panel of my HP3586. It’s powered by the transmitter and has its
B+ cut off during receive to kill any back wave in my receiver.

Other output signals are available on the instrument’s back panel but are not useful to most of us doing
Audio and RF measurements along with being for other specialized equipment, like HP computers and
jitter measuring devices, so won’t be discussed in this document.

7

4. FRONT PANEL DESCRIPTION AND INITIAL SET UP

4.1 General - Before turning on your HP3586 be sure it’s configured for the right input power, usually

115VAC. Also be sure the filter on its back panel is clean, if not remove it and clean with only soap and
water. The filter should be cleaned after every 720 hours of operation.

In the following sections and chapter you’ll see capital letters in b rackets like [AUTO]. These identify
buttons used to control the instrument or enter data. The front panel of a HP3586 is broken into groups or
sub panels, which we’ll refer to in this chapter to aid in locating indiv id ual displays and controls.

Additionally, on the front panel you will see some buttons with a second label below the button or two
labels on the button like buttons near the keyboard, these are dual function buttons. Ones with two labels
on the button will select the proper functio n automatically by the button that is previously p ushed, like if
you push [FREQ] the instrument knows MHz, KHz, or Hz apply instead of the other labels like –db or -db.
The ones with labels below and above the button are shifted button. On the same panel you will see an
unlabeled colored shift button with a light on it. When it’s light is on , the lower label of the dual-pur pose
adjacent buttons will apply. Also buttons with lights will have their function on when their light is on.

Plug you HP3586 into AC power and the STANDBY annunciator should light, next turn on your HP3586
by pressing [POWER]. It will first perform an auto calibration for about 5 seconds. If a ERR or CE with a
number is displayed on the LH front panel read out there has been an error during calibration, refer to
Appendix A for a listing of errors and suggested corrective action. The [AUTO CAL] button light should
be on but you can turn off auto cal at any time by pressing this button, but for now leave it on. After the
initial power up and auto cal the instrument should default to the low distortion-measuring mode with a
range setting of 10db auto. During the following sections we will describe the front panel controls. Since
the instrument will default to the selective low distortion level measuring mode when first it’s powered up
you may not need to perform all the described button pushing commands but just confirm that the
instrument is set up as described.

During the following sections of this chapter, have your HP3586 available in front of you to find the
described controls and LED displays.

4.2 Measurement/Entry Group - On the upper LH is the measurement/entry sub panel, which is used

for displaying the power or voltage measurements and their units on a LED display. The measuring range
and range full scale range value is set using it’s buttons. Set the range by pressing [10db] and the full scale
range limit by pressing [AUTO] for the automatic mode. The analog meter reads the relative level of
signals within the selected 100db or 10db range. With the 100db and auto settings this meter will work as
a relative signal strength meter to aid in frequency tuning. Press [dbm] to have the display read in dbm
units. A dbm annunciator should now light to indicate the units are shown in dbm. The [OFFSET] button
is used to subtract values placed in an offset register that will be subtracted from level values computed by
the instrument to correct or normalize displayed level values. We will discuss this feature later, for now
leave it off. Other buttons we’ll discuss later during some of the examples.

4.3 Frequency/Entry Group - On the upper RH side of the front panel is the frequency/entry sub

panel. This panel will usually display the frequency that th e instrument is tuned to. It will display durin g
frequency entry frequencies being entered by the instrument’s keyboard in KHz or Hz. This frequency will
be the center RF frequency of the selected band pass filter except when in the SSB channel measurement
modes. On all models this panel can select a LSB or USB, side band channel for measurement using the
two channel buttons with a funny symbol I can’t show with Word. The left button is for LSB while the
one on the right is for USB. A counter button is provided to start the frequency measurement counter
system. Only the A and B versions have the SSB entry frequency selection buttons. The carrier button
should be on when in one of the SSB channel modes and tuning a SSB signal. This changes the display to
read SSB carrier frequency instead of filter center RF frequency. Even when their lig hts are on, the tone

8

and carrier buttons are only active in the SSB channel modes. The tone button is only useful for phone line
analysis and won’t be used or discussed in this document.

4.4 Status Group - This small status sub panel on the top far right indicates if the instrument is receiving

or sending data to a remote computer and weather it’s under local or remote control. If the remote
annunciator is on, press [LOCAL]. For our use it should always be in local front panel control mode.

4.5 Measurement Mode Group - On the lower LH side is the measurement mode sub panel that’s used

for selection of how level a measurement will be made by the instrument. All versions have the selectiv e
mode buttons, but only the A and B versions have the specialized SSB channel modes for performing many
SSB channel measurements. The only useful SSB modes I have found a use for are noise/demod, carrier,
and impulse modes. With the shift key light off, press the selective [LO DIST] key to select the maximum
dynamic measurement range for the instrument.

4.6 Termination Group – Never put more than +27dbm or .5 watts total power into the input 50

ohm or 75 ohm connector of a HP3586 when using the internal termination. Never put more than
+42 volts total AC + DC into an unterminated connector.

The termination sub panel is also located on the lower LH of the con trol panel. Th is pan el is u sed to select
the input termination for an input signal. The 50 or 75 ohm unbalanced input on the LH side of the panel is
the only ones useful for radio work and used in the examples of this document. The others use non­standard RF circuit impedances and are for telephone applications. See Chapter 3 for a complete
description on how to connect to the unbalanced low impedance input.

For the measurements we’ll be doing in the following chapter, press the [100K 50pf] button on an A or B
versions. On the C version press the [50 ohm] button and the unlabeled shift key to the right of the 75 ohm
key to remove its 50 ohm load. If you’re not connected in parallel with a terminated load like a radio
receiver, and need a termination such as when being directly connected to an antenna feed line, turn off the
shift key’s light on the C version to provide a load. For unterminated 50 ohm loads using the A or B
version you will need to provide an external 50 ohm termination. In Appendix C is a schematic for a
termination box with a blocking capacitor that I use with my HP3586B.

4.7 Entry Group - On the lower center of the front panel is located the entry sub panel. This sub panel

is used for entry of frequencies, data offsets, frequency tuning steps, full scale measurement values, and
transferring frequency and offset values to their respective registers by using its keyboard buttons.

One very important key is the measurement continue key, [MEAS CONT]. During many data entries that
use one of the LED displays this key’s red light will turn on or flash indicating the instrument’s
measurement process has been interrupted. Anytime you see this button’s light and want to return to the
measurement mode press this key to continue measuring. You can also press it to cancel a mistaken
partially keyboard entry.

Another useful feature of the HP3586 is its ability to store its configuration settings for future use in
making similar future measurements. To do this you can press [STORE] on the entry sub panel followed
by any number from 1 to 9 on the keyboard. This will store the presen t configuration of the instrument in
the memory location of the number pressed for future recall and to save setup time. To recall the
configuration press [RECALL] followed by the register number to rapidly configure the instrument to a
previously stored configuration. To return to the default power up configuration, press [RECALL] then
enter 0. These configurations will be stored after the front panel power button is o ff and the instrument is
in standby as long is AC power is connected to the instrument or its internal battery is charged.
Unfortunately many surplus HP3586’s have dead batteries or their batteries removed and will loose their
stored configurations when disconnected from AC power.

9

If you press [OFFSET] on this sub panel you’ll first see the offset in the measurement level offset register.
If the number you want to enter is close to the present one in the data offset register, you can change the
existing number up or down using the arrow keys, [↑] or [↓] and then press one of the db buttons and
followed by [MEAS CONT].

4.8 Frequency/Tune Group - On the lower right side of the front panel is the frequency/tune sub panel.

This sub panel contains a knob, which is useful in fine-tuning the instrument’s frequency, especially to
SSB signals. Different automatic tuning steps are selected for the selected filters using the [AUTO]
button. Entry panel pre-programmed steps can be selected by pressing the frequency step button. The
actual step size is entered on the entry sub panel for the [FREQ STEP] button. Pressing the off button can
lock off the frequency tune function.

4.9 Bandwidth Group - On the lower right is the bandwidth sub panel, which is used to select the

instrument’s bandwidth that a power or voltage measurements are to be taken over. All models have 20Hz
and 400Hz filters. The A and B versions will have one additional filter of 1740Hz, 2000Hz or 3100Hz. A
and B versions may also have the optional WTD audio no ise filter which is selected by a fourth button to
be in series with the wide third filter. For now select the widest filter your HP3586 has.

4.10 Audio Group - On the lower far right is the audio sub panel. This panel contains a small speaker

and headphone jack along with a volume control knob for output of audio from the SSB detector. Since
we won’t be using the audio output during our first measurements turn the volume knob full CCW to turn
off the sound.

4.11 Improving SSB Reception - This method that is not in the HP operator’s manual gets around the

problem of these signals being very distorted in the instrument’s speaker due to the fact the automatic
range level selection is acting as a AGC system for the SSB demodulator but because of its slow action
there is heavy distortion on the onset of audio signals such as words. I first set the instrument in the 10db
and auto range selection mode, press [10db] then [AUTO] on the frequency/entry sub panel if they aren’t
on. Next press [AUTO] on the measurement/entry panel and tune the speaker’s audio for best possible
audio. Then enter a frequency step of one Hz by pressing [FREQ STEP] on the entry panel and enter 1
followed by [Hz] and [MEAS CONT]. Now press [FREQ STEP] on the frequency/entry sub panel and
again tune for best audio.

Now to improve the speaker audio by preventing over loading the SSB demodulator, lock the instrument
into manual IF gain control by pressing [ENTRY] on the frequency/ entry sub pan el. This will stop the IF
amps AGC action and fix the gain of the IF strip to that of the last automatic setting. This should partially
reduce distortion but to further reduce it, press [FULL SCALE] on the entry sub panel and use the [↑] key
to move the range full scale setting shown on the level display up until the modulation peaks on the analog
meter are near 1/3 scale and turn up the speaker’s volume if necessary. If you go too far and loose the
audio, then press [↓] to increase the IF’s gain but I’ve found 1/3 scale on the analog meter gives best audio.
You can experiment and find the best IF gain setting by entering smaller and larger limits using these keys
just like you would using a manual RF or IF gain control knob on your receiver. If you get UL or OL on
the level measurement display, don’t worry if your just tuning or listening to SSB, this only indicates level
measurements are inaccurate. Also to not have your SSB signal interrupted during tuning or monitoring,
turn off auto cal. However when doing level measurements, always have auto cal back on and press
[AUTO] on the measurement/entry sub panel when your doing signal level measurements.

4.12 Back Panel Oscillator Output – On the HP3586’s back panel is located a female BNC connector

labeled Fo that supplies an output of 0 dbm, 75 ohm from the internal tracking o scillator. Its frequency
will always equal to the frequency of the selected filter’s center band pass frequency. This output is
disabled in the wideband measuring mode.

10

5. SETTING AND MEASURING FREQUENCY

5.1 General - Now we’re ready to have some fun doing examples of how to use your HP3586. This

chapter we’ll show how to use the HP3586 as a VFO by adjusting its frequency and outputting this
frequency for controlling an outboard device like an AM transmitter. We’ll also command the instrument
to measure the frequency of a received AM carrier then lock its output to the carrier’s for zero beating to
another transmitter’s carrier along with checking your HP3586’s frequency calibration. These examples
can be used in all the selective measurement. For now stay in the low distortion selective mode.

5.2 Setting Frequency - The easiest way to set the frequency of the instrument is to enter the desired

frequency using the entry keyboard. On the entry keyboard first press [FREQ], enter a number for the
desired frequency on the keyboard. Then press one of the dual function [Hz], [KHz] or [MHz] buttons for
the units the frequency is in. The frequency display will now read the frequen cy you have j ust entered and
a CENTER annunciator on the display will light indicating this is the frequency the center of its selected
filter. It will also output this frequency to the back panel Fo connector at a 0dbm, 75 ohm level. Now the
HP3586 can be used as an outboard VFO for controlling other devices through its Fo connector. In
Appendix C is the schematic of an amplifier I use to drive my AM transmitters from this output.

To make small frequency adjustments you can use the frequency tune knob. But first you have to set up
the resolution of this control. First go to the entry panel and press [FREQ STEP] and enter on the
keyboard the step resolution you want, I usually use 10Hz or for fine tuning of carriers so let’s enter 10,
then press the [Hz] button for the units of the step you selected followed by the [MEAS CONT] button to
return the instruments to its measuring mode. Now go to the frequency tune knob and press the [FREQ
STEP] button. As you turn the knob you will see the frequency display change in 10Hz increments. Since
the instruments frequency register is being changed the tracking oscillator o utput at Fo is also changing
with the displayed frequency. For faster tuning you can press the [AUTO] button, which selects frequency
steps depending on what bandwidth filter you selected. Knob tuning is a handy feature I use for zero
beating the instrument’s Fo output to a carrier being receiving on my 75A4 receiver. I turn on the exciter
stage in my transmitter then using the HP3586’s frequency tune knob to adjust the HP3586’s frequency to
zero beat with the received carrier while listening to my 75A4.

5.3 Automatically Determining a Station’s Frequency – Be sure the 75 or 50 ohm connector is

connected in parallel with your receivers antenna input as described in the previous section. To use this
feature the instrument must be receiving a steady signal that’s stronger than any other signals in its filter’s
pass band.

To automatically tune the HP-3586 to exactly the frequency of a received carrier, tune the carrier into the
pass band of the instrument’s selected filter. I usually use the instrument’s widest filter, which we already
selected in the previous chapter when setting up the instrument. Turn up the volume knob on the audio
panel on the lower RH side of the front panel to hear signals being received and be sure either USB or LSB
is selected using the buttons below the frequency display. Press the [AUTO] button for the frequency
input knob and tune it into the filter’s pass band. Tune the tone for zero beat on one side of the filter’s band
pass and you should be able to confirm the carrier is the one you want to tune to by listening to the audio
from the carrier’s side band. Be sure you’re in the 10db measurement range and auto full scale for a good
speaker output.

After confirming the stations identity, tune the carrier back into the band pass indicated by a strong carrier
tone and press [COUNTER] under the frequency display to turn on the frequency counter. The display
frequency will now automatically lock onto the received carrier’s frequency. Next press [CNTR→FREQ]
on the keyboard entry panel to store the counter frequency in the frequency register then [COUNTER] to
turn off the counter followed by [MEAS CONT] and return the display and instrument’s frequency to the
new contents of the frequency register. The instrument’s frequency is now the carrier’s measured
frequency and in the speaker you should now hear the received carrier’s tone at around half the frequency
of the filters band pass frequency indicating the carrier is now exactly in the center of the filter’s pass band.

11

If there is other strong signals in the filter’s band pass and the instrument has trouble locking on to the
received carrier, select a narrower filter and repeat the above procedure.

Unfortunately the HP3586 can’t be easily used as a receiver when controlling a transmitter, see section

16.11 of Chapter 16 for a possible method. It only has a SSB product detector and only displays the center
RF frequency that its filter is tuned to, so after locking onto a carrier, you will h ave to turn the volume
control knob full CCW to kill the carrier’s tone in the speaker. Then use your outboard receiver to copy
the other station.

5.4 Checking Your Instrument’s Frequency Calibration – HP recommends that the instrument be

calibrated each year. Unfortunately most of us don’t have access to a calibration lab and can’t afford to
pay a lab to do this for us. But we can check its frequency calibration using one of the frequency standard
WWV stations. Select a wide filter to make it easy to tune in one of the WWV stations, press [3100Hz] or
the button for your widest filter. With the same setup as the p revious section tune your instrument to one
of the following frequencies, 2.500MHz, 5.000MHz, or 10.000MHz. Be sure to have an antenna
connected to your instrument’s unplaced input.

Turn up the audio volume on the audio sub panel to find a frequency where WWV is well above the noise.
You should hear a strong tone from its carrier in the filter’s pass band. You can also confirm you are tuned
to WWV by tuning the tone for zero beat using the frequency tuning knob and listen for the announcer to
identify the station as WWV in its AM side band. Be careful since W W V will sen d tones at times that yo u
could lock onto by mistake, it’s better to tune when their tone is off. Now retune the carrier to th e filters
center and switch to your 400Hz filter being sure the WWV carrier is within the filters pass band.

Now press [COUNTER] on the frequency/entry sub panel and read what your HP3586 says the WWV
carrier frequency is. The difference from exactly one of the above frequencies you first tuned to is the
frequency error in your HP3586 since WWV stations have their frequency held to within a small fraction
of a cycle. See section 16.8 of Chapter 16 for a suggested way of keeping your HP3586’s frequency
accurately calibrated. Also see section 2.4 of Chapter 2 to see if you have the 004 frequency standard
option and if it’s activated.

12