HP 10642 G2 Reference Manual

Microsoft Windows Event ID and SNMP Traps

Reference Guide

For use with SmartStart version 8.25

Part number: 347870-009
Ninth edition: June 2009

Legal notices

© Copyright 2003, 2009 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are

set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed
as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211
and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial
Items are licensed to the U.S. Government under vendor’s standard commercial license.

Microsoft

®

, Windows®, Windows NT®, and Windows Server® are U.S. registered trademarks of Microsoft Corporation.

Contents 3

Contents

Introduction ...........................................................................................................................................4

Windows NT® event log format ................................................................................................................. 4

Agent descriptions ................................................................................................................................... 4

Where to go for additional help ................................................................................................................ 5

Telephone numbers .................................................................................................................................. 5

Foundation agents..................................................................................................................................6

Event Identifiers 256-774.......................................................................................................................... 6

Event Identifiers 1105-1808...................................................................................................................... 9

Event Identifiers 2048-2359.................................................................................................................... 17

Event Identifiers 3072-3876.................................................................................................................... 21

Event Identifiers 4352-4626.................................................................................................................... 25

Storage agents.....................................................................................................................................29

Event Identifiers 256-774........................................................................................................................ 29

Event Identifiers 1061-1098.................................................................................................................... 32

Event Identifiers 1101-1199.................................................................................................................... 38

Event Identifiers 1200-1294.................................................................................................................... 64

Event Identifiers 1343-4613.................................................................................................................... 77

Server agents....................................................................................................................................... 82

Event Identifiers 256-774........................................................................................................................ 82

Event Identifiers 1024-1092.................................................................................................................... 85

Event Identifiers 1103-1183.................................................................................................................... 93

Event Identifiers 1539-3352.................................................................................................................. 124

Event Identifiers 5632-5684.................................................................................................................. 126

NIC agents........................................................................................................................................129

Event Identifiers 256-299...................................................................................................................... 129

Event Identifiers 300-1293.................................................................................................................... 133

Introduction 4

Introduction

This document contains a listing of the Microsoft® Windows Server® 2003 Event Log messages
associated with SNMP traps, which are generated by the HP Insight Management Agents for Servers
for Windows

®

. Each event entry has the corresponding SNMP trap number used by the agents. Other
information on the events in this document includes Event Severity, Event Message, Event Message
Source, Event Symptom, and Supporting SNMP Trap Data.

Windows NT® event log format

The following pages contain HP Insight Management events that are entered into the Microsoft®
Windows NT

®

Event Log when they occur.
Values are 32-bit values laid out as follows:
3 3 2 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1
1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
+-------+--+--+---------------------------------------------+---------------------------------------------------------------+
|Sev|C|R| Facility | Code |
+-------+--+--+---------------------------------------------+---------------------------------------------------------------+
where:
Sev—The severity code
00—Success
01—Informational
10—Warning
11—Error
C—The customer code flag
R—A reserved bit
Facility—The facility code (always “CPQ”)
Code—The facility’s status code—the event number; the upper byte refers to the HP Insight

Management Agent that served the event, the lower byte is the actual event number

Agent descriptions

• Foundation/Host Agent—cpqhsmsg

• Sever Agent—cpqsvmsg

• Storage Agent—cpqstmsg

• NIC Agent—cpqnimsg

Introduction 5

Where to go for additional help

In addition to this guide, the following information sources are available:

• User documentation

• HP Insight Manager software

Telephone numbers

For the name of the nearest HP authorized reseller:

• In the United States, see the HP US service locator webpage,

http://www.hp.com/service_locator.

• In other locations, see the HP website, http://www.hp.com.

For HP technical support:

• In North America:

○ Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days

a week. For continuous quality improvement, calls may be recorded or monitored.

○ If you have purchased a Care Pack (service upgrade), call 1-800-633-3600. For more

information about Care Packs, see the HP website,

http://www.hp.com.

• Outside North America, call the nearest HP Technical Support Phone Center. For telephone

numbers for worldwide Technical Support Centers, see the HP website,

http://www.hp.com.

Foundation agents 6

Foundation agents

Event Identifiers 256-774

Event identifier: cpqhsmsg.dll - 256 (Hex)0x84350100 (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service detected an error. The insertion string is: %1. The data

contains the error code.

Event identifier: cpqhsmsg.dll - 257 (Hex)0x84350101 (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not allocate memory. The data contains the error

code.

Event identifier: cpqhsmsg.dll - 258 (Hex)0x84350102 (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not register with the Service Control Manager.

The data contains the error code.

Event identifier: cpqhsmsg.dll - 259 (Hex)0x84350103 (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not set the service status with the Service Control

Manager. The data contains the error code.

Event identifier: cpqhsmsg.dll - 260 (Hex)0x84350104 (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not create an event object. The data contains the

error code.

Event identifier: cpqhsmsg.dll - 261 (Hex)0x84350105 (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not open registry key “%1”. The data contains the

error code.

Event identifier: cpqhsmsg.dll - 262 (Hex)0x84350106 (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not start any agents successfully.

Event identifier: cpqhsmsg.dll - 263 (Hex)0x84350107 (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not read the registry value “%1”. The data

contains the error code.

Foundation agents 7

Event identifier: cpqhsmsg.dll - 264 (Hex)0x84350108 (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not load the module “%1”. The data contains the

error code.

Event identifier: cpqhsmsg.dll - 265 (Hex)0x84350109 (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could get the control function for module “%1”. The

data contains the error code.

Event identifier: cpqhsmsg.dll - 266 (Hex)0x8435010a (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not initialize agent “%1”. The data contains the

error code.

Event identifier: cpqhsmsg.dll - 267 (Hex)0x8435010b (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not start agent “%1”. The data contains the error

code.

Event identifier: cpqhsmsg.dll - 268 (Hex)0x8435010c (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service detected an invalid state for agent “%1”. The data

contains the state.

Event identifier: cpqhsmsg.dll - 269 (Hex)0x8435010d (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not stop agent “%1”. The data contains the error

code.

Event identifier: cpqhsmsg.dll - 270 (Hex)0x8435010e (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not terminate agent “%1”. The data contains the

error code.

Event identifier: cpqhsmsg.dll - 271 (Hex)0x8435010f (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not unload the module “%1”. The data contains

the error code.

Event identifier: cpqhsmsg.dll - 272 (Hex)0x84350110 (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation Agents service could not create the registry key “%1”. The data

contains the error code.

Event identifier: cpqhsmsg.dll - 273 (Hex)0x84350111 (Service Event)

Log Severity: Warning (2)

Foundation agents 8

Log Message: The Foundation Agents service could not write the registry value “%1”. The data
contains the error code.

Event identifier: cpqhsmsg.dll - 399 (Hex)0xc435018f (Service Event)

Log Severity: Error (3)
Log Message: The Foundation Agents service encountered a fatal error. The service is terminating.

The data contains the error code.

Event identifier: cpqhsmsg.dll - 400 (Hex)0x44350190 (Service Event)

Log Severity: Information (1)
Log Message: The Foundation Agents service version %1 has started.

Event identifier: cpqhsmsg.dll - 401 (Hex)0x44350191 (Service Event)

Log Severity: Information (1)
Log Message: %1

Event identifier: cpqhsmsg.dll - 402 (Hex)0x44350192 (Service Event)

Log Severity: Information (1)
Log Message: The Foundation Agents could not find the SNMP service. Please install the SNMP

service to enabled remote management of the server.

Event identifier: cpqhsmsg.dll - 768 (Hex)0x84350300 (Service Event)

Log Severity: Warning (2)
Log Message: The Host Remote Alerter detected an invalid data type within an alert definition.

Event identifier: cpqhsmsg.dll - 769 (Hex)0x84350301 (Service Event)

Log Severity: Warning (2)
Log Message: The Host Remote Alerter detected an error while attempting to log an alert remotely.

The data contains the error code.

Event identifier: cpqhsmsg.dll - 770 (Hex)0x84350302 (Service Event)

Log Severity: Warning (2)
Log Message: The Host Remote Alerter detected an error while attempting to retrieve data from key =

%1 in the registry. The data contains the error code.

Event identifier: cpqhsmsg.dll - 771 (Hex)0x84350303 (Service Event)

Log Severity: Warning (2)
Log Message: The Host Remote Alerter was unable to log an event in the event log of the system

named %1. The data contains the error code.

Event identifier: cpqhsmsg.dll - 772 (Hex)0xc4350304 (Service Event)

Log Severity: Error (3)
Log Message: The Host Remote Alerter detected a null handle on initialization. The data contains the

error code.

Event identifier: cpqhsmsg.dll - 773 (Hex)0xc4350305 (Service Event)

Log Severity: Error (3)

Foundation agents 9

Log Message: The Host Remote Alerter received an error on WaitForMultipleObjects call. The data
contains the error code.

Event identifier: cpqhsmsg.dll - 774 (Hex)0xc4350306 (Service Event)

Log Severity: Error (3)
Log Message: The Host Remote Alerter received an error on ResetEvent call. The data contains the

error code.

Event Identifiers 1105-1808

NT Event ID: 1105 (Hex)0x44350451 (cpqhsmsg.dll)

Log Severity: Information (1)
Log Message: %1
SNMP Trap: cpqHo2GenericTrap - 11003 in CPQHOST.MIB
Symptom: Generic trap.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHoGenericData

Supporting SNMP Trap Description: “[cpqHoGenericData]”

NT Event ID: 1106 (Hex)0x44350452 (cpqhsmsg.dll)

Log Severity: Information (1)
Log Message: %1
SNMP Trap: cpqHo2AppErrorTrap - 11004 in CPQHOST.MIB
Symptom: An application has generated an exception. Specific error information is contained in the

variable cpqHoSwPerfAppErrorDesc.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHoSwPerfAppErrorDesc

Supporting SNMP Trap Description: “[cpqHoSwPerfAppErrorDesc]”

NT Event ID: 1162 (Hex)0x8435048a (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message: Rising Threshold Passed.
SNMP Trap: cpqMeRisingAlarmExtended - 10005 in CPQTHRSH.MIB
Symptom: Rising Threshold passed. An alarm entry has crossed its rising threshold. The instances of

those objects contained within the variable list are those of the alarm entry that generated this trap.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Foundation agents 10

• cpqMeAlarmVariable

• cpqMeAlarmSampleType

• cpqMeAlarmValue

• cpqMeAlarmRisingThreshold

• cpqMeAlarmOwner

• cpqMeAlarmSeverity

• cpqMeAlarmExtendedDescription

Supporting SNMP Trap Description: “[cpqMeAlarmOwner]: Variable [cpqMeAlarmVariable] has
value [cpqMeAlarmValue] >= [cpqMeAlarmRisingThreshold].”

NT Event ID: 1163 (Hex)0x8435048b (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message: Falling Threshold Passed.
SNMP Trap: cpqMeFallingAlarmExtended - 10006 in CPQTHRSH.MIB
Symptom: Falling Threshold passed. An alarm entry has crossed its falling threshold. The instances of

those objects contained within the variable list are those of the alarm entry that generated this trap.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqMeAlarmVariable

• cpqMeAlarmSampleType

• cpqMeAlarmValue

• cpqMeAlarmFallingThreshold

• cpqMeAlarmOwner

• cpqMeAlarmSeverity

• cpqMeAlarmExtendedDescription

Supporting SNMP Trap Description: “[cpqMeAlarmOwner]: Variable [cpqMeAlarmVariable] has
value [cpqMeAlarmValue] <= [cpqMeAlarmFallingThreshold].”

NT Event ID: 1164 (Hex)0x8435048c (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message: Critical Rising Threshold Passed.
SNMP Trap: cpqMeCriticalRisingAlarmExtended - 10007 in CPQTHRSH.MIB
Symptom: Critical Rising Threshold passed. An alarm entry has crossed its critical rising threshold. The

instances of those objects contained within the variable list are those of the alarm entry that generated
this trap.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqMeAlarmVariable

• cpqMeAlarmSampleType

• cpqMeAlarmValue

Foundation agents 11

• cpqMeAlarmRisingThreshold

• cpqMeAlarmOwner

• cpqMeAlarmSeverity

• cpqMeAlarmExtendedDescription

Supporting SNMP Trap Description: “[cpqMeAlarmOwner]: Variable [cpqMeAlarmVariable] has
value [cpqMeAlarmValue] <= [cpqMeAlarmRisingThreshold].”

NT Event ID: 1165 (Hex)0x8435048d (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message: Critical Falling Threshold Passed.
SNMP Trap: cpqMeCriticalFallingAlarmExtended - 10008 in CPQTHRSH.MIB
Symptom: Critical Falling Threshold passed. An alarm entry has crossed its critical falling threshold.

The instances of those objects contained within the variable list are those of the alarm entry that
generated this trap.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqMeAlarmVariable

• cpqMeAlarmSampleType

• cpqMeAlarmValue

• cpqMeAlarmFallingThreshold

• cpqMeAlarmOwner

• cpqMeAlarmSeverity

• cpqMeAlarmExtendedDescription

Supporting SNMP Trap Description: “[cpqMeAlarmOwner]: Variable [cpqMeAlarmVariable] has
value [cpqMeAlarmValue] <= [cpqMeAlarmFallingThreshold].”

NT Event ID: 1166 (Hex)0x8435048e (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message: %1
SNMP Trap: cpqHoProcessEventTrap - 11011 in CPQHOST.MIB
Symptom: A monitored process has either started or stopped running.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHoSwRunningTrapDesc

Supporting SNMP Trap Description: “[cpqHoSwRunningTrapDesc]”

NT Event ID: 1167 (Hex)0x8435048f (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message: The cluster resource %4 has become degraded.
SNMP Trap: cpqClusterResourceDegraded - 15005 in CPQCLUS.MIB

Foundation agents 12

Symptom: This trap is sent any time the condition of a cluster resource becomes degraded.
User Action: Make a note of the cluster resource name, and then check the resource for the cause of

the degraded condition.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqClusterResourceName

Supporting SNMP Trap Description: “Cluster resource [cpqClusterResourceName] has become
degraded.”

NT Event ID: 1168 (Hex)0xc4350490 (cpqhsmsg.dll)

Log Severity: Error (3)
Log Message: The cluster resource %4 has failed.
SNMP Trap: cpqClusterResourceFailed - 15006 in CPQCLUS.MIB
Symptom: This trap is sent any time the condition of a cluster resource has failed.
User Action: Make a note of the cluster resource name, and then check the resource for the cause of

the failure.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqClusterResourceName

Supporting SNMP Trap Description: “Cluster resource [cpqClusterResourceName] has failed.”

NT Event ID: 1169 (Hex)0x84350491 (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message: The cluster network %4 has become degraded.
SNMP Trap: cpqClusterNetworkDegraded - 15007 in CPQCLUS.MIB
Symptom: This trap is sent any time the condition of a cluster network becomes degraded.
User Action: Make a note of the cluster network name, and then check the network for the cause of

the degraded condition.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqClusterNetworkName

Supporting SNMP Trap Description: “Cluster network [cpqClusterNetworkName] has become
degraded.”

NT Event ID: 1170 (Hex)0xc4350492 (cpqhsmsg.dll)

Log Severity: Error (3)
Log Message: The cluster network %4 has failed.
SNMP Trap: cpqClusterNetworkFailed - 15008 in CPQCLUS.MIB

Foundation agents 13

Symptom: This trap is sent any time the condition of a cluster network has failed.
User Action: Make a note of the cluster network name, and then check the network for the cause of

the failure.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqClusterNetworkName

Supporting SNMP Trap Description: “Cluster network [cpqClusterNetworkName] has failed.”

NT Event ID:1171 (Hex)0x84350493 (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message: The cluster service on %4 has become degraded.
SNMP Trap: cpqClusterNodeDegraded - 15003 in CPQCLUS.MIB
Symptom: This trap is sent any time the condition of a node in the cluster becomes degraded.
User Action: Make a note of the cluster node name, and then check the node for the cause of the

degraded condition.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqClusterNodeName

Supporting SNMP Trap Description: “Cluster service on [cpqClusterNodeName] has become
degraded.”

NT Event ID: 1172 (Hex)0xc4350494 (cpqhsmsg.dll)

Log Severity: Error (3)
Log Message: The cluster service on %4 has failed.
SNMP Trap: cpqClusterNodeFailed - 15004 in CPQCLUS.MIB
Symptom: This trap is sent any time the condition of a node in the cluster has failed.
User Action: Make a note of the cluster node name, and then check the node for the cause of the

failure.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqClusterNodeName

Supporting SNMP Trap Description: “Cluster service on [cpqClusterNodeName] has failed.”

NT Event ID: 1173 (Hex)0x84350495 (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message: The Processor Performance Instance, '%4' is degraded with Processor Time of %5

percent.
SNMP Trap: cpqOsCpuTimeDegraded - 19001 in CPQWINOS.MIB

Foundation agents 14

Symptom: The Processor Time performance property is set to degraded.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqOsCpuIndex

• cpqOsCpuInstance

• cpqOsCpuTimePercent

Supporting SNMP Trap Description: “The Processor performance Instance, [cpqOsCpuInstance] is
degraded with Processor Time of [cpqOsCpuTimePercent] percent.”

NT Event ID: 1174 (Hex)0xc4350496 (cpqhsmsg.dll)

Log Severity: Error (3)
Log Message: The Processor Performance Instance, '%4' is failed with Processor Time of %5 percent.
SNMP Trap: cpqOsCpuTimeFailed - 19002 in CPQWINOS.MIB
Symptom: The Processor Time performance property is set to critical.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqOsCpuIndex

• cpqOsCpuInstance

• cpqOsCpuTimePercent

Supporting SNMP Trap Description: “The Processor performance Instance, [cpqOsCpuInstance] is
critical with Processor Time of [cpqOsCpuTimePercent] percent.”

NT Event ID: 1175 (Hex)0x84350497 (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message:The Cache Performance Instance, '%4' is degraded with Cache Copy Read Hits of %5

percent.
SNMP Trap: cpqOsCacheCopyReadHitsDegraded - 19003 in CPQWINOS.MIB
Symptom: The Cache CopyReadHits performance property is set to degraded.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqOsCacheIndex

• cpqOsCacheInstance

• cpqOsCacheCopyReadHitsPercent

Supporting SNMP Trap Description: “The Cache performance property is degraded with
CopyReadHits of [cpqOsCacheCopyReadHitsPercent] percent.”

NT Event ID: 1176 (Hex)0xc4350498 (cpqhsmsg.dll)

Log Severity: Error (3)

Foundation agents 15

Log Message: The Cache Performance Instance, '%4' is failed with Cache Copy Read Hits of %5
percent.

SNMP Trap: cpqOsCacheCopyReadHitsFailed - 19004 in CPQWINOS.MIB
Symptom: The Cache CopyReadHits performance property is set to critical.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqOsCacheIndex

• cpqOsCacheInstance

• cpqOsCacheCopyReadHitsPercent

Supporting SNMP Trap Description: “The Cache performance property is critical with CopyReadHits
of [cpqOsCacheCopyReadHitsPercent] percent.”

NT Event ID: 1177 (Hex)0x84350499 (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message: The PagingFile Performance Instance, '%4' is degraded with PagingFile Usage of %5

percent.
SNMP Trap: cpqOsPageFileUsageDegraded - 19005 in CPQWINOS.MIB
Symptom: The PagingFile Usage performance property is set to degraded.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqOsPagingFileIndex

• cpqOsPagingFileInstance

• cpqOsPageFileUsagePercent

Supporting SNMP Trap Description: “The PagingFile performance instance,
[cpqOsPagingFileInstance] is degraded with PagingFile Usage of [cpqOsPageFileUsagePercent]
percent.”

NT Event ID: 1178 (Hex)0xc435049a (cpqhsmsg.dll)

Log Severity: Error (3)
Log Message: The PagingFile Performance Instance, '%4' is failed with PagingFile Usage of %5

percent.
SNMP Trap: cpqOsPageFileUsageFailed - 19006 in CPQWINOS.MIB
Symptom: The PagingFile Usage performance property is set to critical.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqOsPagingFileIndex

• cpqOsPagingFileInstance

• cpqOsPageFileUsagePercent

Foundation agents 16

Supporting SNMP Trap Description: “The PagingFile performance instance,
[cpqOsPagingFileInstance] is critical with PagingFile Usage of [cpqOsPageFileUsagePercent]
percent.”

NT Event ID: 1179 (Hex)0x8435049b (cpqhsmsg.dll)

Log Severity: Warning (2)
Log Message: The Logical Disk Performance Instance, '%4' is degraded with Disk Busy Time of %5

percent.
SNMP Trap: cpqOsLogicalDiskBusyTimeDegraded - 19007 in CPQWINOS.MIB
Symptom: The LogicalDisk BusyTime performance property is set to degraded.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqOsLogicalDiskIndex

• cpqOsLogicalDiskInstance

• cpqOsLogicalDiskBusyTimePercent

Supporting SNMP Trap Description: “The LogicalDisk performance instance,
[cpqOsLogicalDiskInstance] is degraded with DiskBusyTime of [cpqOsLogicalDiskBusyTimePercent]
percent.”

NT Event ID: 1180 (Hex)0xc435049c (cpqhsmsg.dll)

Log Severity: Error (3)
Log Message: The Logical Disk Performance Instance, '%4' is failed with Disk Busy Time of %5

percent.
SNMP Trap: cpqOsLogicalDiskBusyTimeFailed - 19008 in CPQWINOS.MIB
Symptom: The LogicalDisk BusyTime performance property is set to critical.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqOsLogicalDiskIndex

• cpqOsLogicalDiskInstance

• cpqOsLogicalDiskBusyTimePercent

Supporting SNMP Trap Description: “The LogicalDisk performance instance,
[cpqOsLogicalDiskInstance] is critical with DiskBusyTime of [cpqOsLogicalDiskBusyTimePercent]
percent.”

NT Event ID: 1181 (Hex)0xc435049d (cpqhsmsg.dll)

Log Severity: Error (3)
Log Message: '%4'
SNMP Trap: cpqHoCriticalSoftwareUpdateTrap - 11014 in CPQHOST.MIB
Symptom: This trap is sent to notify the user of a Critical Software Update.
Supporting SNMP Trap Data:

• sysName

Foundation agents 17

• cpqHoTrapFlags

• cpqHoCriticalSoftwareUpdateData

Supporting SNMP Trap Description: “[cpqHoCriticalSoftwareUpdateData]”

Event identifier: cpqhsmsg.dll - 1792 (Hex)0x84350700 (Service Event)

Log Severity: Warning (2)
Log Message: The agent is unable to generate traps due to an error during initialization.

Event identifier: cpqhsmsg.dll - 1795 (Hex)0x84350703 (Service Event)

Log Severity: Warning (2)
Log Message: The agent is older than other components. The agent is older than the other

components of the Management Agents. Reinstall all of the Management Agents to correct this error.

Event identifier: cpqhsmsg.dll - 1796 (Hex)0x84350704 (Service Event)

Log Severity: Warning (2)
Log Message: The %1 Agent is older than other components. The %1 Agent is older than the other

components of the Management Agents. Reinstall all of the Management Agents to correct this error.

Event identifier: cpqhsmsg.dll - 1800 (Hex)0x84350708 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to read security configuration information. SNMP sets have been disabled.

Event identifier: cpqhsmsg.dll - 1803 (Hex)0xc435070b (Service Event)

Log Severity: Error (3)
Log Message: Unable to load a required library. This error can be caused by a corrupt or missing

file. Reinstalling the Management Agents or running the Emergency Repair procedure may correct this
error.

Event identifier: cpqhsmsg.dll - 1806 (Hex)0x8435070e (Service Event)

Log Severity: Warning (2)
Log Message: The Foundation SNMP Agent service is not running. The agent has determined that the

Foundation Agents service is not running. Stop the SNMP service and restart the Foundation Agents
service. If the error persists, reinstalling the Management Agents may correct this error.

Event identifier: cpqhsmsg.dll - 1808 (Hex)0x44350710 (Service Event)

Log Severity: Information (1)
Log Message: The agent could not deliver trap %1. The agent was unable to use Asynchronous

Management to deliver a trap. This can be caused by a failure in the Remote Access Service or by a
missing or invalid configuration. Use the Management Agents control panel to verify the
Asynchronous Management configuration settings. Use the Network control panel to verify the Remote
Access configuration. If this error persists, reinstalling the Management Agents or the Remote Access
Service may correct this error. For more information, see the Management Agents Asynchronous
Management documentation.

Event Identifiers 2048-2359

Event identifier: cpqhsmsg.dll - 2048 (Hex)0x84350800 (Service Event)

Foundation agents 18

Log Severity: Warning (2)
Log Message: Unable to allocate memory. This indicates a low memory condition. Rebooting the

system will correct this error.

Event identifier: cpqhsmsg.dll - 2049 (Hex)0x84350801 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to read from the registry. This error can be caused by a corrupt registry or a

low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 2050 (Hex)0x84350802 (Service Event)

Log Severity: Warning (2)
Log Message: Could not create the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 2051 (Hex)0x84350803 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to read from the registry. This error can be caused by a corrupt registry or a

low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 2052 (Hex)0x84350804 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to read “%1” from the registry. This error can be caused by a corrupt registry

or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 2053 (Hex)0x84350805 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to read “%1” from the registry. This error can be caused by a corrupt registry

or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 2056 (Hex)0x84350808 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to create thread. This error can be caused by a low memory condition.

Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 2098 (Hex)0x84350832 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to acquire file system information. This error can be caused by an unformatted

partition or by a partition that has been recently modified. Formatting the partition or rebooting the
server may correct this error.

Event identifier: cpqhsmsg.dll - 2099 (Hex)0x84350833 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to acquire file system information for %1. This error can be caused by a low

memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 2100 (Hex)0x84350834 (Service Event)

Log Severity: Warning (2)

Foundation agents 19

Log Message: Unable to acquire the current process list. This error can be caused by a low memory
condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 2101 (Hex)0x84350835 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to acquire the CPU performance data. This error can be caused by a low

memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 2304 (Hex)0x84350900 (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent could not allocate memory. The data contains the error code.

Event identifier: cpqhsmsg.dll - 2305 (Hex)0x84350901 (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent could not open the base of the registry. The data contains the

error code.

Event identifier: cpqhsmsg.dll - 2306 (Hex)0x84350902 (Service Event)

Log Severity: Warning (2)
Log Message: “%1”. The data contains the error code.

Event identifier: cpqhsmsg.dll - 2307 (Hex)0x84350903 (Service Event)

Log Severity: Warning (2)
Log Message: “%1”. The data contains the error code.

Event identifier: cpqhsmsg.dll - 2308 (Hex)0x84350904 (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent could not read the registry value “%1”. The data contains the

error code.

Event identifier: cpqhsmsg.dll - 2309 (Hex)0x84350905 (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent found an incorrect type for registry value “%1”. The data contains

the type found.

Event identifier: cpqhsmsg.dll - 2310 (Hex)0x84350906 (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent could not create a necessary event. The data contains the error

code.

Event identifier: cpqhsmsg.dll - 2311 (Hex)0x84350907 (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent could not set an event. The data contains the error code.

Event identifier: cpqhsmsg.dll - 2312 (Hex)0x84350908 (Service Event)

Log Severity: Warning (2)

Foundation agents 20

Log Message: The Threshold Agent could not create its main thread of execution. The data contains
the error code.

Event identifier: cpqhsmsg.dll - 2313 (Hex)0x84350909 (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent main thread did not terminate properly. The data contains the

error code.

Event identifier: cpqhsmsg.dll - 2314 (Hex)0x8435090a (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent got an unexpected error code while waiting for an event. The

data contains the error code.

Event identifier: cpqhsmsg.dll - 2315 (Hex)0x8435090b (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent did not respond to a request. The data contains the error code.

Event identifier: cpqhsmsg.dll - 2316 (Hex)0x8435090c (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent received an unknown action code from the service. The data

contains the action code.

Event identifier: cpqhsmsg.dll - 2317 (Hex)0x8435090d (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent could not get the system type. The data contains the error code.

Event identifier: cpqhsmsg.dll - 2354 (Hex)0x84350932 (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent could not create an SNMP session. The data contains the error

code.

Event identifier: cpqhsmsg.dll - 2355 (Hex)0x84350933 (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent SNMP request failed. The data contains the error code. Action: 1)

Be sure that the SNMP service is configured to allow SNMP requests from “localhost”. 2) Be sure that
there is an adequate amount of free memory.

Event identifier: cpqhsmsg.dll - 2356 (Hex)0x84350934 (Service Event)

Log Severity: Warning (2)
Log Message: “%1”. The data contains the error code.

Event identifier: cpqhsmsg.dll - 2357 (Hex)0x84350935 (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent could not set the variable because it is unsupported. The data

contains the error code.

Event identifier: cpqhsmsg.dll - 2358 (Hex)0x84350936 (Service Event)

Log Severity: Warning (2)

Foundation agents 21

Log Message: The Threshold Agent could not set the variable because the value is invalid or out of
range. The data contains the error code.

Event identifier: cpqhsmsg.dll - 2359 (Hex)0x84350937 (Service Event)

Log Severity: Warning (2)
Log Message: The Threshold Agent is not loaded. Sets are not available. The data contains the error

code.

Event Identifiers 3072-3876

Event identifier: cpqhsmsg.dll - 3072 (Hex)0x84350c00 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read from the registry sub-key. This error can be caused by a corrupt registry

or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 3073 (Hex)0x84350c01 (Service Event)

Log Severity: Warning (2)
Log Message: Could not create the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 3074 (Hex)0x84350c02 (Service Event)

Log Severity: Warning (2)
Log Message: Could not create the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 3075 (Hex)0x84350c03 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to read “%1” from the registry.
This error can be caused by a corrupt registry or a low memory condition. Rebooting the server may

correct this error.

Event identifier: cpqhsmsg.dll - 3076 (Hex)0x84350c04 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to read “%1” from the registry. This error can be caused by a corrupt registry

or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 3084 (Hex)0xc4350c0c (Service Event)

Log Severity: Error (3)
Log Message: Unable to read configuration (%1) from the registry. This error can be caused by a

corrupt registry, a low memory condition, or incomplete configuration. Reconfigure the Management
Agents using the control panel. Rebooting the server may also correct this error.

Event identifier: cpqhsmsg.dll - 3085 (Hex)0x84350c0d (Service Event)

Log Severity: Warning (2)
Log Message: Unable to write (%1) to the registry. This error can be caused by a corrupt registry or a

low memory condition. Rebooting the server may correct this error.

Foundation agents 22

Event identifier: cpqhsmsg.dll - 3086 (Hex)0x84350c0e (Service Event)

Log Severity: Warning (2)
Log Message: Unable to load a required library. This error can be caused by a corrupt or missing

file. Reinstalling the Management Agents or running the Emergency Repair procedure may correct this
error.

Event identifier: cpqhsmsg.dll - 3090 (Hex)0x84350c12 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to allocate memory. This indicates a low memory condition. Rebooting the

system will correct this error.

Event identifier: cpqhsmsg.dll - 3840 (Hex)0x84350f00 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to allocate memory. This indicates a low memory condition. Rebooting the

system will correct this error.

Event identifier: cpqhsmsg.dll - 3841 (Hex)0x84350f01 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read from the registry sub-key. This error can be caused by a corrupt registry

or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 3842 (Hex)0x84350f02 (Service Event)

Log Severity: Warning (2)
Log Message: Could not write the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 3843 (Hex)0x84350f03 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 3844 (Hex)0x84350f04 (Service Event)

Log Severity: Warning (2)
Log Message: Could not write the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 3845 (Hex)0x84350f05 (Service Event)

Log Severity: Warning (2)
Log Message: Could not write the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 3855 (Hex)0x84350f0f (Service Event)

Log Severity: Warning (2)
Log Message: Could not open a cluster enumeration object. The Cluster service may not be running.

Try to restart the Cluster service.

Event identifier: cpqhsmsg.dll - 3856 (Hex)0x84350f10 (Service Event)

Foundation agents 23

Log Severity: Warning (2)
Log Message: Could not enumerate all of the nodes in the cluster. The data contains the error code.

Event identifier: cpqhsmsg.dll - 3857 (Hex)0x84350f11 (Service Event)

Log Severity: Warning (2)
Log Message: Could not get the cluster's status. The Cluster service may not be running. Try to restart

the Cluster service.

Event identifier: cpqhsmsg.dll - 3858 (Hex)0x84350f12 (Service Event)

Log Severity: Warning (2)
Log Message: Could not open the enumerated resource. The Cluster service may not be running. Try

to restart the Cluster service.

Event identifier: cpqhsmsg.dll - 3859 (Hex)0x84350f13 (Service Event)

Log Severity: Warning (2)
Log Message: Could not enumerate the cluster's resources. The Cluster service may not be running.

Try to restart the Cluster service.

Event identifier: cpqhsmsg.dll - 3860 (Hex)0x44350f14 (Service Event)

Log Severity: Information (1)
Log Message: Resource status is online.

Event identifier: cpqhsmsg.dll - 3861 (Hex)0x44350f15 (Service Event)

Log Severity: Information (1)
Log Message: Resource status is offline. The resource has failed or was taken offline by a cluster

administrator.

Event identifier: cpqhsmsg.dll - 3862 (Hex)0x44350f16 (Service Event)

Log Severity: Information (1)
Log Message: Could not get the resource status. The Cluster service may not be running. Try to restart

the Cluster service.

Event identifier: cpqhsmsg.dll - 3863 (Hex)0x44350f17 (Service Event)

Log Severity: Information (1)
Log Message: Resource status is inherited.

Event identifier: cpqhsmsg.dll - 3864 (Hex)0x44350f18 (Service Event)

Log Severity: Information (1)
Log Message: Resource status is initializing. The Cluster service is starting.

Event identifier: cpqhsmsg.dll - 3865 (Hex)0x44350f19 (Service Event)

Log Severity: Information (1)
Log Message: Resource status is pending. The Cluster service is starting or the resource is being put

back online or being taken offline.

Event identifier: cpqhsmsg.dll - 3866 (Hex)0x44350f1a (Service Event)

Log Severity: Information (1)

Foundation agents 24

Log Message: Resource status is online pending. The resource is being put back online.

Event identifier: cpqhsmsg.dll - 3867 (Hex)0x44350f1b (Service Event)

Log Severity: Information (1)
Log Message: Resource status is offline pending. The resource is being taken offline.

Event identifier: cpqhsmsg.dll - 3868 (Hex)0x84350f1c (Service Event)

Log Severity: Warning (2)
Log Message: Cluster information is unavailable. The Cluster service may not be running. Try to restart

the Cluster service.

Event identifier: cpqhsmsg.dll - 3869 (Hex)0x84350f1d (Service Event)

Log Severity: Warning (2)
Log Message: The Cluster service is not running. The Cluster service has failed or has not started yet.

Try to restart the cluster service.

Event identifier: cpqhsmsg.dll - 3870 (Hex)0x84350f1e (Service Event)

Log Severity: Warning (2)
Log Message: The Agent could not open the Cluster service. The Cluster service may have been

stopped. Try to restart the cluster service.

Event identifier: cpqhsmsg.dll - 3871 (Hex)0x84350f1f (Service Event)

Log Severity: Warning (2)
Log Message: The Agent could not open the Cluster service registry key.

Event identifier: cpqhsmsg.dll - 3872 (Hex)0x84350f20 (Service Event)

Log Severity: Warning (2)
Log Message: The specified storage class is not supported by the Agent. The Agent only supports the

disk resource class.

Event identifier: cpqhsmsg.dll - 3873 (Hex)0x84350f21 (Service Event)

Log Severity: Warning (2)
Log Message: The fibre controller resided at the storage box is off-line. The Agent only supports the

disk resource class.

Event identifier: cpqhsmsg.dll - 3874 (Hex)0x84350f22 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 3875 (Hex)0x84350f23 (Service Event)

Log Severity: Warning (2)
Log Message: Could not open enumerated network. The Cluster service may not be running. Try to

restart the Cluster service.

Event identifier: cpqhsmsg.dll - 3876 (Hex)0x84350f24 (Service Event)

Log Severity: Warning (2)

Foundation agents 25

Log Message: Could not enumerate the cluster's networks. The Cluster service may not be running. Try
to restart the Cluster service.

Event Identifiers 4352-4626

Event identifier: cpqhsmsg.dll - 4352 (Hex)0x84351100 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent could not allocate memory. The data contains the error

code.

Event identifier: cpqhsmsg.dll - 4353 (Hex)0x84351101 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent could not open the base of the registry. The data

contains the error code.

Event identifier: cpqhsmsg.dll - 4354 (Hex)0x84351102 (Service Event)

Log Severity: Warning (2)
Log Message: “%1”. The data contains the error code.

Event identifier: cpqhsmsg.dll - 4355 (Hex)0x84351103 (Service Event)

Log Severity: Warning (2)
Log Message: “%1”. The data contains the error code.

Event identifier: cpqhsmsg.dll - 4356 (Hex)0x84351104 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent could not read the registry value “%1”. The data

contains the error code.

Event identifier: cpqhsmsg.dll - 4357 (Hex)0x84351105 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent found an incorrect type for registry value “%1”. The

data contains the type found.

Event identifier: cpqhsmsg.dll - 4358 (Hex)0x84351106 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent could not create a necessary event. The data contains

the error code.

Event identifier: cpqhsmsg.dll - 4359 (Hex)0x84351107 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent could not set an event. The data contains the error code.

Event identifier: cpqhsmsg.dll - 4360 (Hex)0x84351108 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent could not create its main thread of execution. The data

contains the error code.

Foundation agents 26

Event identifier: cpqhsmsg.dll - 4361 (Hex)0x84351109 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent main thread did not terminate properly. The data

contains the error code.

Event identifier: cpqhsmsg.dll - 4362 (Hex)0x8435110a (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent got an unexpected error code while waiting for an

event. The data contains the error code.

Event identifier: cpqhsmsg.dll - 4363 (Hex)0x8435110b (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent did not respond to a request. The data contains the error

code.

Event identifier: cpqhsmsg.dll - 4364 (Hex)0x8435110c (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent received an unknown action code from the service. The

data contains the action code.

Event identifier: cpqhsmsg.dll - 4365 (Hex)0x8435110d (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent could not get the system type. The data contains the

error code.

Event identifier: cpqhsmsg.dll - 4402 (Hex)0x84351132 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent could not create an SNMP session. The data contains

the error code.

Event identifier: cpqhsmsg.dll - 4403 (Hex)0x84351133 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent SNMP request failed. The data contains the error code.
Action: Complete the following steps:

1. Be sure that the SNMP service is configured to allow SNMP requests from “localhost.”

2. Be sure that there is an adequate amount of free memory.

Event identifier: cpqhsmsg.dll - 4405 (Hex)0x84351135 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent could not set the variable because it is unsupported. The

data contains the error code.

Event identifier: cpqhsmsg.dll - 4406 (Hex)0x84351136 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent could not set the variable because the value is invalid or

out of range. The data contains the error code.

Foundation agents 27

Event identifier: cpqhsmsg.dll - 4407 (Hex)0x84351137 (Service Event)

Log Severity: Warning (2)
Log Message: The External Status MIB Agent is not loaded. Sets are not available. The data contains

the error code.

Event identifier: cpqhsmsg.dll - 4608 (Hex)0x84351200 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to allocate memory. This indicates a low memory condition. Rebooting the

system will correct this error.

Event identifier: cpqhsmsg.dll - 4609 (Hex)0x84351201 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read from the registry sub-key. This error can be caused by a corrupt registry

or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 4610 (Hex)0x84351202 (Service Event)

Log Severity: Warning (2)
Log Message: Could not write the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 4611 (Hex)0x84351203 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 4612 (Hex)0x84351204 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read from the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 4613 (Hex)0x84351205 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read from the registry sub-key: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqhsmsg.dll - 4623 (Hex)0x8435120f (Service Event)

Log Severity: Warning (2)
Log Message: The Agent could not access WMI. The WMI support may have not been started or

installed. Restart or Install WMI service and restart the agents.

Event identifier: cpqhsmsg.dll - 4624 (Hex)0x84351210 (Service Event)

Log Severity: Warning (2)
Log Message: The Agent requires WMI service to be running. If NT 4.0 installed the latest version of

WMI from Microsoft

®

, WMI service may need to be started.

Event identifier: cpqhsmsg.dll - 4625 (Hex)0x84351211 (Service Event)

Log Severity: Warning (2)

Foundation agents 28

Log Message: The Agent failed to initialize WMI. WMI service may not have started or may still be in
the starting state.

Event identifier: cpqhsmsg.dll - 4626 (Hex)0x84351212 (Service Event)

Log Severity: Warning (2)
Log Message: The Agent failed to process the MOF file to get the data from WMI. Problem with WMI

service or MOF file or wrong file paths used.

Storage agents 29

Storage agents

Event Identifiers 256-774

Event identifier: cpqstmsg.dll - 256 (Hex)0x84350100 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service detected an error. The insertion string is: %1. The data

contains the error code.

Event identifier: cpqstmsg.dll - 257 (Hex)0x84350101 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not allocate memory. The data contains the error

code.

Event identifier: cpqstmsg.dll - 258 (Hex)0x84350102 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not register with the Service Control Manager. The

data contains the error code.

Event identifier: cpqstmsg.dll - 259 (Hex)0x84350103 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not set the service status with the Service Control

Manager. The data contains the error code.

Event identifier: cpqstmsg.dll - 260 (Hex)0x84350104 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not create an event object. The data contains the

error code.

Event identifier: cpqstmsg.dll - 261 (Hex)0x84350105 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not open registry key “%1”. The data contains the

error code.

Event identifier: cpqstmsg.dll - 262 (Hex)0x84350106 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not start any agents successfully.

Event identifier: cpqstmsg.dll - 263 (Hex)0x84350107 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not read the registry value “%1”. The data contains

the error code.

Storage agents 30

Event identifier: cpqstmsg.dll - 264 (Hex)0x84350108 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not load the module “%1”. The data contains the

error code.

Event identifier: cpqstmsg.dll - 265 (Hex)0x84350109 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could get the control function for module “%1”. The data

contains the error code.

Event identifier: cpqstmsg.dll - 267 (Hex)0x8435010b (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not start agent “%1”. The data contains the error

code.

Event identifier: cpqstmsg.dll - 268 (Hex)0x8435010c (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service detected an invalid state for agent “%1”. The data contains

the state.

Event identifier: cpqstmsg.dll - 269 (Hex)0x8435010d (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not stop agent “%1”. The data contains the error

code.

Event identifier: cpqstmsg.dll - 270 (Hex)0x8435010e (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not terminate agent “%1”. The data contains the

error code.

Event identifier: cpqstmsg.dll - 271 (Hex)0x8435010f (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not unload the module “%1”. The data contains the

error code.

Event identifier: cpqstmsg.dll - 272 (Hex)0x84350110 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not create the registry key “%1”. The data contains

the error code.

Event identifier: cpqstmsg.dll - 273 (Hex)0x84350111 (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agents service could not write the registry value “%1”. The data contains

the error code.

Event identifier: cpqstmsg.dll - 399 (Hex)0xc435018f (Service Event)

Log Severity: Error (3)

Storage agents 31

Log Message: The Storage Agents service encountered a fatal error. The service is terminating. The
data contains the error code.

Event identifier: cpqstmsg.dll - 400 (Hex)0x44350190 (Service Event)

Log Severity: Information (1)
Log Message: The Storage Agents service version %1 has started.

Event identifier: cpqstmsg.dll - 401 (Hex)0x44350191 (Service Event)

Log Severity: Information (1)
Log Message: %1

Event identifier: cpqstmsg.dll - 512 (Hex)0x84350200 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to allocate memory. This indicates a low memory condition. Rebooting the

system will correct this error.

Event identifier: cpqstmsg.dll - 513 (Hex)0x84350201 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read from the registry subkey. This error can be caused by a corrupt registry

or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 514 (Hex)0x84350202 (Service Event)

Log Severity: Warning (2)
Log Message: Could not write the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 515 (Hex)0x84350203 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 516 (Hex)0x84350204 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 517 (Hex)0x84350205 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 526 (Hex)0x8435020e (Service Event)

Log Severity: Warning (2)
Log Message: Unsupported storage system. The ProLiant storage system %1 is not supported by this

version of the Storage Agents. Upgrade the agents to the latest version.

Event identifier: cpqstmsg.dll - 527 (Hex)0x8435020f (Service Event)

Log Severity: Warning (2)

Storage agents 32

Log Message: The Drive Array Agent storage system table is full.

Event identifier: cpqstmsg.dll - 574 (Hex)0x8435023e (Service Event)

Log Severity: Warning (2)
Log Message: The Drive Array Agent failed to get capacity on SCSI drive because SCSI pass through

IOCTL failed.

Event identifier: cpqstmsg.dll - 768 (Hex)0x84350300 (Service Event)

Log Severity: Warning (2)
Log Message: The Remote Alerter Agent detected an invalid data type within an alert definition.

Event identifier: cpqstmsg.dll - 769 (Hex)0x84350301 (Service Event)

Log Severity: Warning (2)
Log Message: The Remote Alerter Agent detected an error while attempting to log an alert remotely.

The data contains the error code.

Event identifier: cpqstmsg.dll - 771 (Hex)0x84350303 (Service Event)

Log Severity: Warning (2)
Log Message: The Remote Alerter Agent was unable to log an event in the event log of the system

named %1. The data contains the error code.

Event identifier: cpqstmsg.dll - 772 (Hex)0xc4350304 (Service Event)

Log Severity: Error (3)
Log Message: The Remote Alerter Agent detected a null handle on initialization. The data contains the

error code.

Event identifier: cpqstmsg.dll - 773 (Hex)0xc4350305 (Service Event)

Log Severity: Error (3)
Log Message: The Remote Alerter Agent received an error on WaitForMultipleObjects call. The data

contains the error code.

Event identifier: cpqstmsg.dll - 774 (Hex)0xc4350306 (Service Event)

Log Severity: Error (3)
Log Message: The Remote Alerter Agent received an error on ResetEvent call. The data contains the

error code.

Event Identifiers 1061-1098

NT Event ID: 1061 (Hex)0xc4350425 (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: Drive Array Physical Drive Threshold Exceeded.
Log Message: The physical drive in slot %4, port %5, bay %6 with serial number “%7”, has

exceeded a drive threshold.
SNMP Trap: cpqDa5PhyDrvThreshPassedTrap - 3030 in CPQIDA.MIB
Symptom: Physical Drive Threshold Passed. This trap indicates that the agent has detected a factory

threshold associated with one of the physical drive objects on a drive array, has been exceeded.

Storage agents 33

User Action: Replace the physical drive.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaPhyDrvCntlrIndex

• cpqDaPhyDrvBusNumber

• cpqDaPhyDrvBay

• cpqDaPhyDrvModel

• cpqDaPhyDrvFWRev

• cpqDaPhyDrvSerialNum

Supporting SNMP Trap Description: “Factory threshold passed for a physical drive.”

NT Event ID: 1062 (Hex)0xc4350426 (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: Drive Array Logical Drive Status Change.
Log Message: Logical drive number %5 on the array controller in slot %4 has a new status of %2.
SNMP Trap: cpqDa3LogDrvStatusChange - 3008 in CPQIDA.MIB
Symptom: Logical Drive Status Change. This trap indicates that the agent has detected a change in

the status of a drive array logical drive. The variable cpqDaLogDrvStatus indicates the current logical
drive status.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaLogDrvStatus

Supporting SNMP Trap Description: “Status is now [cpqDaLogDrvStatus].”

NT Event ID: 1063 (Hex)0xc4350427 (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: Drive Array Spare Drive Status Change.
Log Message: The spare drive in slot %4, port %5, bay %6 has a new status of %2.
SNMP Trap: cpqDa4SpareStatusChange - 3017 in CPQIDA.MIB
Symptom: Spare Drive Status Change. This trap indicates that the agent has detected a change in the

status of a drive array spare drive. The variable cpqDaSpareStatus indicates the current spare drive
status.

User Action: If the spare drive status is failed, replace the drive.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaSpareStatus

• cpqDaSpareCntlrIndex

• cpqDaSpareBusNumber

Storage agents 34

• cpqDaSpareBay

Supporting SNMP Trap Description: “Spare Status is now [cpqDaSpareStatus].”

NT Event ID: 1064 (Hex)0xc4350428 (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: Drive Array Physical Drive Status Change.
Log Message: The physical drive in slot %4, port %5, bay %6 with serial number “%7”, has a new

status of %2.
SNMP Trap: cpqDa5PhyDrvStatusChange - 3029 in CPQIDA.MIB
Symptom: Physical Drive Status Change. This trap indicates that the agent has detected a change in

the status of a drive array physical drive. The variable cpaDaPhyDrvStatus indicates the current
physical drive status.

User Action: If the physical drive status is failed(3) or predictiveFailure(4), replace the drive.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaPhyDrvStatus

• cpqDaPhyDrvCntlrIndex

• cpqDaPhyDrvBusNumber

• cpqDaPhyDrvBay

• cpqDaPhyDrvModel

• cpqDaPhyDrvFWRev

• cpqDaPhyDrvSerialNum

• cpqDaPhyDrvFailureCode

Supporting SNMP Trap Description: “Physical Drive Status is now [cpqDaPhyDrvStatus].”

NT Event ID: 1065 (Hex)0xc4350429 (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: Drive Array Accelerator Status Change.
Log Message: The array accelerator board attached to the array controller in slot %4 has a new

status of %2.
SNMP Trap: cpqDa5AccelStatusChange - 3025 in CPQIDA.MIB
Symptom: Accelerator Board Status Change. This trap indicates that the agent has detected a change

in the status of an array accelerator cache board. The current status is represented by the variable
cpqDaAccelStatus.

User Action: If the accelerator board status is permDisabled(5), you may need to replace the
accelerator board.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrSlot

• cpqDaCntlrModel

Storage agents 35

• cpqDaAccelSerialNumber

• cpqDaAccelTotalMemory

• cpqDaAccelStatus

• cpqDaAccelErrCode

Supporting SNMP Trap Description: “Status is now [cpqDaAccelStatus].”

NT Event ID: 1066 (Hex)0xc435042a (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: Drive Array Accelerator Bad Data.
Log Message: The array accelerator board attached to the array controller in slot %4 is reporting that

it contains bad cached data.
SNMP Trap: cpqDa5AccelBadDataTrap - 3026 in CPQIDA.MIB
Symptom: Accelerator Board Bad Data. This trap indicates that the agent has detected an array

accelerator cache board that has lost battery power. If data was being stored in the accelerator
cache memory when the server lost power, that data has been lost.

User Action: Verify that no data has been lost.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrSlot

• cpqDaCntlrModel

• cpqDaAccelSerialNumber

• cpqDaAccelTotalMemory

Supporting SNMP Trap Description: “Accelerator lost battery power. Data Loss possible.”

NT Event ID: 1067 (Hex)0xc435042b (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: Drive Array Accelerator Battery Failed.
Log Message: The array accelerator board attached to the array controller in slot %4 is reporting a

battery failure.
SNMP Trap: cpqDa5AccelBatteryFailed - 3027 in CPQIDA.MIB
Symptom: Accelerator Board Battery Failed. This trap indicates that the agent has detected a battery

failure associated with the array accelerator cache board.
User Action: Replace the Accelerator Cache Board.
Supporting SNMP Trap Data:
sysName

• cpqHoTrapFlags

• cpqDaCntlrSlot

• cpqDaCntlrModel

• cpqDaAccelSerialNumber

• cpqDaAccelTotalMemory

Storage agents 36

Supporting SNMP Trap Description: “Battery status is failed.”

NT Event ID: 1068 (Hex)0xc435042c (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: SCSI Controller Status Change.
Log Message: The SCSI controller in slot %4, SCSI bus %5 has a new status of %2.
SNMP Trap: cpqScsi3CntlrStatusChange - 5005 in CPQSCSI.MIB
Symptom: SCSI Controller Status Change. The Insight Agent has detected a change in the controller

status of a SCSI Controller. The variable cpqScsiCntlrStatus indicates the current controller status.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqScsiCntlrStatus

Supporting SNMP Trap Description: “Status is now [cpqScsiCntlrStatus].”

NT Event ID: 1069 (Hex)0xc435042d (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: SCSI Logical Drive Status Change.
Log Message: The SCSI logical drive with SCSI target %6 connected to SCSI bus %5 of the controller

in slot %4, SCSI has a new status of %2.
SNMP Trap: cpqScsi3LogDrvStatusChange - 5021 in CPQSCSI.MIB
Symptom: Logical Drive Statues Change. The Storage Agent has detected a change in the status of a

SCSI logical drive. The current logical drive status is indicated in the cpqScsiLogDrvStatus variable.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqScsiLogDrvStatus

• cpqScsiLogDrvCntlrIndex

• cpqScsiLogDrvBusIndex

• cpqScsiLogDrvIndex

• cpqScsiLogDrvOsName

Supporting SNMP Trap Description: “Status is now [cpqScsiLogDrvStatus].”

NT Event ID: 1070 (Hex)0xc435042e (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: SCSI Physical Drive Status Change.
Log Message: The SCSI physical drive with SCSI target %6 connected to SCSI bus %5 of the

controller in slot %4 has a new status of %2.
SNMP Trap: cpqScsi5PhyDrvStatusChange - 5020 in CPQSCSI.MIB
Symptom: Physical Drive Status Change. The Storage Agent has detected a change in the status of a

SCSI physical drive. The current physical drive status is indicated in the cpqScsiPhyDrvStatus variable.
Supporting SNMP Trap Data:

Storage agents 37

• sysName

• cpqHoTrapFlags

• cpqScsiPhyDrvStatus

• cpqScsiPhyDrvCntlrIndex

• cpqScsiPhyDrvBusIndex

• cpqScsiPhyDrvIndex

• cpqScsiPhyDrvVendor

• cpqScsiPhyDrvModel

• cpqScsiPhyDrvFWRev

• cpqScsiPhyDrvSerialNum

• cpqScsiPhyDrvOsName

Supporting SNMP Trap Description: “Status is now [cpqScsiPhyDrvStatus].”

NT Event ID: 1075 (Hex)0x84350433 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Fan Status Change.
Log Message: The %6 %7 storage system connected to SCSI bus %5 of the controller in slot %4 has a

new status of %2.
SNMP Trap: cpqSs3FanStatusChange - 8008 in CPQSTSYS.MIB
Symptom: Storage System fan status change. The agent has detected a change in the Fan Status of a

storage system. The variable cpqSsBoxFanStatus indicates the current fan status.
User Action: If the fan status is degraded or failed, replace any failed fans.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsBoxFanStatus

Supporting SNMP Trap Description: “Storage System fan status changed to [cpqSsBoxFanStatus].”

NT Event ID: 1076 (Hex)0xc4350434 (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: Storage System Temperature Failure.
Log Message: The %6 %7 storage system connected to SCSI bus %5 of the controller in slot %4 has a

failed temperature status. Shut down the storage system as soon as possible.
SNMP Trap: cpqSs3TempFailed - 8009 in CPQSTSYS.MIB
Symptom: Storage System temperature failure. The agent has detected that a temperature status has

been set to failed. The storage system is shut down.
User Action: Shut down the storage system as soon as possible. Insure that the storage system

environment is being cooled properly and that no components are overheated.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsBoxTempStatus

Storage agents 38

Supporting SNMP Trap Description: “Storage System will be shut down.”

NT Event ID: 1077 (Hex)0x84350435 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Temperature Degraded.
Log Message: The %6 %7 storage system connected to SCSI bus %5 of the controller in slot %4

system has a temperature outside the normal operating range.
SNMP Trap: cpqSs3TempDegraded - 8010 in CPQSTSYS.MIB
Symptom: Storage System temperature degraded. The agent has detected a temperature status that

has been set to degraded. The storage system's temperature is outside of the normal operating range.
User Action: Shut down the storage system as soon as possible. Be sure that the storage system

environment is being cooled properly and that no components are overheated.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsBoxTempStatus

Supporting SNMP Trap Description: “Temp is outside of normal range.”

NT Event ID: 1078 (Hex)0x44350436 (cpqstmsg.dll)

Log Severity: Information (1)
Event Title: Storage System Temperature OK.
Log Message: The temperature in the %6 %7 storage system connected to SCSI bus %5 of the

controller in slot %4 has returned to the normal operating range.
SNMP Trap: cpqSs3TempOk - 8011 in CPQSTSYS.MIB
Symptom: Storage System temperature OK. The temperature status has been set to OK. The storage

system's temperature has returned to normal operating range. It may be reactivated by the
administrator.

User Action: None.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsBoxTempStatus

Supporting SNMP Trap Description: “Storage System temperature ok.”

Event identifier: cpqstmsg.dll - 1098 (Hex)0x4435044a (Service Event)

Log Severity: Information (1)
Log Message: Drive Array Physical Drive Monitoring is not enabled. The physical drive in slot %4,

port %5, bay %6 with serial number “%7”, does not have drive threshold monitoring enabled.

Event Identifiers 1101-1199

NT Event ID: 1101 (Hex)0x8435044d (cpqstmsg.dll)

Storage agents 39

Log Severity: Warning (2)
Event Title: Storage System Side Panel Removed.
Log Message: The side panel has been removed on the %6 %7 storage system connected to SCSI bus

%5 of the controller in slot %4.
SNMP Trap: cpqSs3SidePanelRemoved - 8013 in CPQSTSYS.MIB
Symptom: Storage System side panel is removed. The side panel status has been set to removed. The

storage system's side panel is not in a properly installed state. This situation may result in improper
cooling of the drives in the storage system due to air flow changes caused by the missing side panel.

User Action: Replace the storage system side panel.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsBoxSidePanelStatus

Supporting SNMP Trap Description: “Side panel is removed from unit.”

NT Event ID: 1102 (Hex)0x4435044e (cpqstmsg.dll)

Log Severity: Information (1)
Event Title: Storage System Side Panel In Place.
Log Message: The side panel has been replaced on the %6 %7 storage system connected to SCSI bus

%5 of the controller in slot %4.
SNMP Trap: cpqSs3SidePanelInPlace - 8012 in CPQSTSYS.MIB
Symptom: Storage System side panel is in place. The side panel status has been set to in place. The

storage system's side panel has returned to a properly installed state.
User Action: None.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsBoxSidePanelStatus

Supporting SNMP Trap Description: “Side panel is re-installed on unit.”

NT Event ID: 1104 (Hex)0x84350450 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Fault Tolerant Power Supply Degraded.
Log Message: The fault tolerant power supply in the %6 %7 storage system connected to SCSI bus %5

of the controller in slot %4 has a degraded status. Restore power or replace any failed power supply.
SNMP Trap: cpqSs4PwrSupplyDegraded - 8015 in CPQSTSYS.MIB
Symptom: A storage system power supply status has been set to degraded.
User Action: Restore power or replace any failed storage system power supply.
Supporting SNMP Trap Data:

• sysName

Storage agents 40

• cpqHoTrapFlags

• cpqSsBoxFltTolPwrSupplyStatus

Supporting SNMP Trap Description: “A storage system power supply unit has become degraded.”

NT Event ID: 1107 (Hex)0xc4350453 (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: SCSI Tape Drive Status Change.
Log Message: The tape drive with SCSI target %6 connected to SCSI bus %5 of the controller in slot

%4 has a new status of %2.
SNMP Trap: cpqTape4PhyDrvStatusChange - 5016 in CPQSCSI.MIB
Symptom: Tape Drive Status Change. The Storage Agent has detected a change in the status of a

Tape drive. The current physical drive status is indicated in the cpqTapePhyDrvStatus variable.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqTapePhyDrvCntlrIndex

• cpqTapePhyDrvBusIndex

• cpqTapePhyDrvScsiIdIndex

• cpqTapePhyDrvStatus

Supporting SNMP Trap Description: “Status is now [cpqTapePhyDrvStatus].”

NT Event ID: 1119 (Hex)0x8435045f (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: SCSI Tape Drive Head Needs Cleaning.
Log Message: The tape drive with SCSI target %6 connected to SCSI bus %5 of the controller in slot

%4 needs to have a cleaning tape inserted and run.
SNMP Trap: cpqTape3PhyDrvCleaningRequired - 5008 in CPQSCSI.MIB
Symptom: Tape Drive Cleaning Required trap. The Insight Agent has detected a tape drive that needs

to have a cleaning tape inserted and run. This causes the tape drive heads to be cleaned.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqTapePhyDrvCondition

Supporting SNMP Trap Description: “Status is now [cpqTapePhyDrvCondition].”

NT Event ID: 1120 (Hex)0x84350460 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: SCSI Tape Drive Cleaning Tape Needs Replacing.
Log Message: The tape drive with SCSI target %6 connected to SCSI bus %5 of the controller in slot

%4 needs the cleaning tape replaced.
SNMP Trap: cpqTape3PhyDrvCleanTapeReplace - 5009 in CPQSCSI.MIB

Storage agents 41

Symptom: Tape Drive Cleaning Tape Needs Replacing. The Insight Agent has detected that an
autoloader tape unit has a cleaning tape that has been fully used and therefore needs to be replaced
with a new cleaning tape.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqTapePhyDrvCondition

Supporting SNMP Trap Description: “Status is now [cpqTapePhyDrvCondition].”

NT Event ID: 1121 (Hex)0x84350461 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: IDE Drive Status Degraded.
Log Message: The IDE drive %4 has a degraded status and should be scheduled for replacement.
SNMP Trap: cpqIdeDriveDegraded - 14001 in CPQIDE.MIB
Symptom: An IDE drive status has been set to degraded.
User Action: The drive should be scheduled for replacement. For detailed information on a component

replacement, see the appropriate Maintenance and Service Guide.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqIdeIdentIndex

Supporting SNMP Trap Description: “IDE drive [cpqIdeIdentIndex] has become degraded.”

NT Event ID: 1122 (Hex)0x44350462 (cpqstmsg.dll)

Log Severity: Information (1)
Event Title: IDE Drive Status OK.
Log Message: The IDE drive %4 has returned to a normal operating condition.
SNMP Trap: cpqIdeDriveOk - 14002 in CPQIDE.MIB
Symptom: An IDE drive status has been set to OK.
User Action: None.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqIdeIdentIndex

Supporting SNMP Trap Description: “IDE drive [cpqIdeIdentIndex] has returned to normal operating
condition.”

Storage agents 42

NT Event ID: 1145 (Hex)0xc4350479 (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: External Array Logical Drive Status Change.
Log Message: Logical drive number %5 on array “%4” has a new status of %6.
SNMP Trap: cpqExtArrayLogDrvStatusChange - 16022 in CPQFCA.MIB
Symptom: External Array Logical Drive Status Change. This trap indicates that the agent has detected

a change in the status of an External Array logical drive. The variable cpqFcaLogDrvStatus indicates
the current logical drive status.

User Action: If the logical drive status is failed, examine the array for failed drives that need
replacement.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqFcaLogDrvBoxIndex

• cpqFcaLogDrvIndex

• cpqFcaLogDrvStatus

• cpqFcaLogDrvOsName

• cpqFcaLogDrvFaultTol

• cpqFcaLogDrvSize

Supporting SNMP Trap Description: “Status is now [cpqFcaLogDrvStatus].”

NT Event ID: 1146 (Hex)0xc435047a (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: External Array Physical Drive Status Change.
Log Message: The physical drive in port %5, bay %6 on array “%4” has a new status of %7.
SNMP Trap: cpqFca2PhyDrvStatusChange - 16016 in CPQFCA.MIB
Symptom: External Array Physical Drive Status Change. This trap indicates that the agent has detected

a change in the status of a physical drive. The variable cpaFcaPhyDrvStatus indicates the current
physical drive status.

User Action: If the physical drive status is threshExceeded(4), predictiveFailure(5) or failed(6), replace
the drive.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqFcaPhyDrvBusNumber

• cpqFcaPhyDrvBay

• cpqFcaPhyDrvStatus

Storage agents 43

• cpqFcaPhyDrvModel

• cpqFcaPhyDrvSerialNum

• cpqFcaPhyDrvFWRev

• cpqFcaPhyDrvFailureCode

Supporting SNMP Trap Description: “Status is now [cpqFcaPhyDrvStatus] for a physical drive on bus
[cpqFcaPhyDrvBusNumber], bay [cpqFcaPhyDrvBay].”

NT Event ID: 1147 (Hex)0xc435047b (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: External Array Spare Drive Status Change.
Log Message: The spare drive in port %5, bay %6 on array “%4” has a new status of %7.
SNMP Trap: cpqFcaSpareStatusChange - 16002 in CPQFCA.MIB
Symptom: External Array Spare Drive Status Change. This trap indicates that the agent has detected a

change in the status of an External Channel Array spare drive. The variable cpqFcaSpareStatus
indicates the current spare drive status. The variable cpqFcaSpareBusNumber indicates the SCSI bus
number associated with this drive.

User Action: If the spare drive status is failed, replace the drive.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqFcaSpareBusNumber

• cpqFcaSpareBay

• cpqFcaSpareStatus

Supporting SNMP Trap Description: “Spare Status is now [cpqFcaSpareStatus] on bus
[cpqFcaSpareBusNumber].”

NT Event ID: 1148 (Hex)0xc435047c (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: External Array Accelerator Status Change.
Log Message: The array accelerator board attached to the external controller in I/O slot %5 of array

“%4” has a new status of %6.
SNMP Trap: cpqFca2AccelStatusChange - 16017 in CPQFCA.MIB
Symptom: External Array Accelerator Board Status Change. This trap indicates that the agent has

detected a change in the status of an Array Accelerator Cache Board. The current status is
represented by the variable cpqFcaAccelStatus.

User Action: If the accelerator board status is permDisabled(5), you may need to replace the
accelerator board.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Storage agents 44

• cpqSsChassisName

• cpqSsChassisTime

• cpqFcaAccelBoxIoSlot

• cpqFcaAccelStatus

• cpqFcaCntlrModel

• cpqFcaAccelSerialNumber

• cpqFcaAccelTotalMemory

• cpqFcaAccelErrCode

Supporting SNMP Trap Description: “Status is now [cpqFcaAccelStatus].”

NT Event ID: 1149 (Hex)0xc435047d (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: External Array Accelerator Bad Data.
Log Message: The array accelerator board attached to the external controller in I/O slot %5 of array

“%4” is reporting that it contains bad cached data.
SNMP Trap: cpqFca2AccelBadDataTrap - 16018 in CPQFCA.MIB
Symptom: External Array Accelerator Board Bad Data. This trap indicates that the agent has detected

an Array Accelerator Cache Board that has lost battery power. If data was being stored in the
accelerator memory when the system lost power, that data has been lost.

User Action: Verify that no data has been lost.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqFcaAccelBoxIoSlot

• cpqFcaCntlrModel

• cpqFcaAccelSerialNumber

• cpqFcaAccelTotalMemory

Supporting SNMP Trap Description: “Accelerator lost battery power. Data Loss possible.”

NT Event ID: 1150 (Hex)0xc435047e (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: External Array Accelerator Battery Failed.
Log Message: The array accelerator board attached to the external controller in I/O slot %5 of array

“%4” is reporting a battery failure.
SNMP Trap: cpqFca2AccelBatteryFailed - 16019 in CPQFCA.MIB
Symptom: External Array Accelerator Board Battery failed. This trap indicates that the agent has

detected a battery failure associated with the Array Accelerator Cache Board.
User Action: Replace the Accelerator Cache Board.
Supporting SNMP Trap Data:

• sysName

Storage agents 45

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqFcaAccelBoxIoSlot

• cpqFcaCntlrModel

• cpqFcaAccelSerialNumber

• cpqFcaAccelTotalMemory

Supporting SNMP Trap Description: “Battery status is failed.”

NT Event ID: 1151 (Hex)0xc435047f (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: External Array Controller Status Change.
Log Message: The external controller in I/O slot %5 of array “%4” has a new status of %6.
SNMP Trap: cpqFca2CntlrStatusChange - 16020 in CPQFCA.MIB
Symptom: External Array Controller Status Change. This trap indicates that the agent has detected a

change in the status of an External Array Controller. The variable cpqFcaCntlrStatus indicates the
current controller status.

User Action: If the controller status is offline(4), access to the storage box has been lost. Check the
storage box and all fibre channel connections for problems.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqFcaCntlrBoxIoSlot

• cpqFcaCntlrStatus

• cpqFcaCntlrModel

• cpqFcaCntlrSerialNumber

• cpqFcaAccelTotalMemory

Supporting SNMP Trap Description: “Status is now [cpqFcaCntlrStatus].”

NT Event ID: 1152 (Hex)0x84350480 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Fan Module Status Change.
Log Message: Storage system “%4” fan module at location %5 has a new status of %6.
SNMP Trap: cpqSsEx2FanStatusChange - 8020 in CPQSTSYS.MIB
Symptom: Storage system fan status change. The agent has detected a change in the fan module

status of a storage system. The variable cpqSsFanModuleStatus indicates the current fan status.
User Action: If the fan status is degraded or failed, replace any failed fans.
Supporting SNMP Trap Data:

• sysName

Storage agents 46

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqSsFanModuleLocation

• cpqSsFanModuleStatus

• cpqSsFanModuleSerialNumber

• cpqSsFanModuleBoardRevision

Supporting SNMP Trap Description: “Storage system fan status changed to [cpqSsFanModuleStatus].”

NT Event ID: 1153 (Hex)0x84350481 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Power Supply Status Change.
Log Message: Storage system “%4” power supply in bay %5 has a new status of %6.
SNMP Trap: cpqSsEx2PowerSupplyStatusChange - 8021 in CPQSTSYS.MIB
Symptom: Storage system power supply status change. The agent has detected a change in the power

supply status of a storage system. The variable cpqSsPowerSupplyStatus indicates the current status.
User Action: If the power supply status is failed, restore power or replace the failed power supply.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqSsPowerSupplyBay

• cpqSsPowerSupplyStatus

• cpqSsPowerSupplySerialNumber

• cpqSsPowerSupplyBoardRevision

• cpqSsPowerSupplyFirmwareRevision

Supporting SNMP Trap Description: “Storage system power supply status changed to
[cpqSsPowerSupplyStatus].”

NT Event ID: 1154 (Hex)0x84350482 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Power Supply UPS Status Change.
Log Message: The UPS attached to storage system “%4” power supply bay %5 has a new status of

%7.
SNMP Trap: cpqSsExPowerSupplyUpsStatusChange - 8018 in CPQSTSYS.MIB
Symptom: Storage system power supply UPS status change. The agent has detected a change status

of a UPS attached to a storage system power supply. The variable cpqSsPowerSupplyUpsStatus
indicates the current status.

User Action: If the UPS status is powerFailed(4) or batteryLow(5), restore power to the UPS.
Supporting SNMP Trap Data:

• sysName

Storage agents 47

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqSsPowerSupplyBay

• cpqSsPowerSupplyUpsStatus

Supporting SNMP Trap Description: “Storage system power supply UPS status changed to
[cpqSsPowerSupplyUpsStatus].”

NT Event ID: 1155 (Hex)0x84350483 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Temperature Sensor Status Change.
Log Message: Storage system “%4” temperature sensor at location %5 has a new status of %6 and a

current temperature value of %7 celsius.
SNMP Trap: cpqSsExTempSensorStatusChange - 8019 in CPQSTSYS.MIB
Symptom: Storage system temperature sensor status change. The agent has detected a change in the

status of a storage system temperature sensor. The variable cpqSsTempSensorStatus indicates the
current status.

User Action: If the temperature status is degraded or failed, shut down the storage system as soon as
possible. Be sure that the storage system environment is being cooled properly and that no
components are overheated.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqSsTempSensorLocation

• cpqSsTempSensorStatus

• cpqSsTempSensorCurrentValue

Supporting SNMP Trap Description: “Storage system temperature sensor status changed to
[cpqSsTempSensorStatus].”

NT Event ID: 1156 (Hex)0x84350484 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: SCSI Tape Library Failed.
Log Message: The SCSI tape library with SCSI target %6 connected to SCSI bus %5 of the controller

in slot %4 has encountered an error.
SNMP Trap: cpqTape3LibraryFailed - 5010 in CPQSCSI.MIB
Symptom: Tape Library Error. The Insight Agent has detected that an autoloader unit has encountered

an error.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Storage agents 48

• cpqTapeLibrarySerialNumber

Supporting SNMP Trap Description: “Tape library [cpqTapeLibrarySerialNumber] is not operational.”

NT Event ID: 1157 (Hex)0x84350485 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: SCSI Tape Library OK.
Log Message: The SCSI tape library with SCSI target %6 connected to SCSI bus %5 of the controller

in slot %4 has recovered from errors.
SNMP Trap: cpqTape3LibraryOkay - 5011 in CPQSCSI.MIB
Symptom: Tape Library Okay. The Insight Agent has detected that an autoloader unit has

recovered from errors.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqTapeLibrarySerialNumber

Supporting SNMP Trap Description: “Tape Library [cpqTapeLibrarySerialNumber] Recovered.”

NT Event ID: 1158 (Hex)0x84350486 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: SCSI Tape Library Degraded.
Log Message: The SCSI tape library with SCSI target %6 connected to SCSI bus %5 of the controller

in slot %4 is in a degraded condition.
SNMP Trap: cpqTape3LibraryDegraded - 5012 in CPQSCSI.MIB
Symptom: Tape Library Degraded. The Insight Agent has detected that an autoloader unit is

in a degraded condition.

• Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqTapeLibrarySerialNumber

Supporting SNMP Trap Description: “Tape library [cpqTapeLibrarySerialNumber] is in a degraded
condition.”

NT Event ID: 1159 (Hex)0x84350487 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: SCSI Tape Library Door Open.
Log Message: The SCSI tape library with SCSI target %6 connected to SCSI bus %5 of the controller

in slot %4 has a door open, so the unit is not operational.
SNMP Trap: cpqTape3LibraryDoorOpen - 5013 in CPQSCSI.MIB
Symptom: Tape Library Door Open. The Insight Agent has detected that the door on an autoloader is

open, so the unit is not operational.
Supporting SNMP Trap Data:

• sysName

Storage agents 49

• cpqHoTrapFlags

• cpqTapeLibrarySerialNumber

Supporting SNMP Trap Description: “Tape library [cpqTapeLibrarySerialNumber] door opened.”

NT Event ID: 1160 (Hex)0x84350488 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: SCSI Tape Library Door Closed.
Log Message: The SCSI tape library with SCSI target %6 connected to SCSI bus %5 of the controller

in slot %4 has a closed door and is now operational.
SNMP Trap: cpqTape3LibraryDoorClosed - 5014 in CPQSCSI.MIB
Symptom: Tape Library Door Closed. The Insight Agent has detected that the door on an autoloader

has closed.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqTapeLibrarySerialNumber

Supporting SNMP Trap Description: “Tape library [cpqTapeLibrarySerialNumber] door closed.”

NT Event ID: 1161 (Hex)0xc4350489 (cpqstmsg.dll)

Log Severity: Error (3)
Event Title: SCSI CD Library Status Change.
Log Message: The CD Library with SCSI target %6 connected to SCSI bus %5 of the controller in slot

%4 has a new status of %2.
SNMP Trap: cpqScsiCdLibraryStatusChange - 5015 in CPQSCSI.MIB
Symptom: CD Library Status Change. The Insight Agent has detected a change in the status of a CD

Library device. The current CD Library status is indicated in the cpqScsiCdLibraryStatus variable.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqCdLibraryCntlrIndex

• cpqCdLibraryBusIndex

• cpqCdLibraryScsiIdIndex

• cpqCdLibraryStatus

Supporting SNMP Trap Description: “Status is now [cpqCdLibraryStatus].”

NT Event ID: 1164 (Hex)0x8435048c (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Controller Status Change.
Log Message: The Drive Array Controller in slot %4 has a new status of %5.
SNMP Trap: cpqDa5CntlrStatusChange - 3028 in CPQIDA.MIB

Storage agents 50

Symptom: Controller Status Change. This trap indicates that the agent has detected a change in the
status of a drive array controller. The variable cpqDaCntlrBoardStatus indicates the current controller
status.

User Action: If the board status is generalFailure(3), you may need to replace the controller. If the
board status is cableProblem(4), check the cable connections between the controller and the storage
system.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrSlot

• cpqDaCntlrBoardStatus

• cpqDaCntlrModel

• cpqDaCntlrSerialNumber

• cpqDaCntlrFWRev

• cpqDaAccelTotalMemory

Supporting SNMP Trap Description: “Status is now [cpqDaCntlrBoardStatus].”

NT Event ID: 1165 (Hex)0x8435048d (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Controller Active.
Log Message: The Drive Array Controller in slot %4 has become the active controller.
SNMP Trap: cpqDaCntlrActive - 3016 in CPQIDA.MIB
Symptom: Controller Active. This trap indicates that the agent has detected that a backup array

controller in a duplexed pair has switched over to the active role. The variable cpqDaCntlrSlot
indicates the active controller slot, and cpqDaCntlrPartnerSlot indicates the backup.

User Action: Check the partner controller for problems. If this was the result of a user initiated switch­over, no action is required.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrSlot

• cpqDaCntlrPartnerSlot

Supporting SNMP Trap Description: “Controller in slot [cpqDaCntlrSlot] is now active.”

NT Event ID: 1173 (Hex)0x84350495 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Fibre Channel Tape Controller Status Change.
Log Message: Fibre Channel tape controller with world wide name “%4” has a new status of %5.
SNMP Trap: cpqFcTapeCntlrStatusChange - 16008 in CPQFCA.MIB
Symptom: Fibre Channel Tape Controller Status Change. This trap indicates that the agent has

detected a change in the status of a Fiber Channel Tape Controller. The variable

Storage agents 51

cpqFcTapeCntlrStatus indicates the current tape controller status. The variable cpqFcTapeCntlrWWN
indicates the unique tape controller world wide name associated with this controller.

User Action: If the tape controller status is offline, access to the tape library and tapes has been lost.
Check the tape library and all Fibre connections for problems.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcTapeCntlrWWN

• cpqFcTapeCntlrStatus

Supporting SNMP Trap Description: “Status is now [cpqFcTapeCntlrStatus] for tape controller
[cpqFcTapeCntlrWWN].”

NT Event ID: 1174 (Hex)0x84350496 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Fibre Channel Tape Library Status Change.
Log Message: The Fibre Channel tape library on tape controller with world wide name “%4”, SCSI

bus %5, SCSI target %6, has a new status of %7.
SNMP Trap: cpqFcTapeLibraryStatusChange - 16009 in CPQFCA.MIB
Symptom: Fibre Channel Tape Library Status Change. This trap indicates that the agent has detected

a change in the status of a Fiber Channel Tape library. The variable cpqFcTapeLibraryStatus indicates
the current tape library status. The variable cpqFcTapeLibraryScsiTarget indicates the SCSI ID of the
tape library.

User Action: If the tape library is failed or is offline, check the tape library front panel and all fibre
channel connections.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcTapeCntlrWWN

• cpqFcTapeLibraryScsiBus

• cpqFcTapeLibraryScsiTarget

• cpqFcTapeLibraryScsiLun

• cpqFcTapeLibraryStatus

Supporting SNMP Trap Description: “Status is now [cpqFcTapeLibraryStatus] for the tape library.”

NT Event ID: 1175 (Hex)0x84350497 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Fibre Channel Tape Library Door Status Change.
Log Message: The Fibre Channel tape library on tape controller with world wide name “%4”, SCSI

bus %5, SCSI target %6, has a new door status of %7.
SNMP Trap: cpqFcTapeLibraryDoorStatusChange - 16010 in CPQFCA.MIB
Symptom: Fibre Channel Tape Library Door Status Change. This trap indicates that the agent has

detected a change in the door status of a Fiber Channel Tape library. The variable

Storage agents 52

cpqFcTapeLibraryDoorStatus indicates the current tape library door status. The variable
cpqFcTapeLibraryScsiTarget indicates the SCSI ID of the tape library.

User Action: If the tape library door is open, close the tape library door.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcTapeCntlrWWN

• cpqFcTapeLibraryScsiBus

• cpqFcTapeLibraryScsiTarget

• cpqFcTapeLibraryScsiLun

• cpqFcTapeLibraryDoorStatus

Supporting SNMP Trap Description: “The door is [cpqFcTapeLibraryDoorStatus] for tape library.”

NT Event ID: 1176 (Hex)0x84350498 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Fibre Channel Tape Drive Status Change.
Log Message: The Fibre Channel tape drive on tape controller with world wide name “%4”, SCSI bus

%5, SCSI target %6, has a new status of %7.
SNMP Trap: cpqFcTapeDriveStatusChange - 16011 in CPQFCA.MIB
Symptom: Fibre Channel Tape Drive Status Change. This trap indicates that the agent has detected a

change in the status of a Fiber Channel Tape Drive. The variable cpqFcTapeDriveStatus indicates the
current tape status. The variable cpqFcTapeDriveScsiTarget indicates the SCSI ID of the tape drive.

User Action: If the tape is failed or is offline, check the tape and all fibre channel connections.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcTapeCntlrWWN

• cpqFcTapeDriveScsiBus

• cpqFcTapeDriveScsiTarget

• cpqFcTapeDriveScsiLun

• cpqFcTapeDriveStatus

Supporting SNMP Trap Description: “Status is now [cpqFcTapeDriveStatus] for a tape drive.”

Event ID: 1177 (Hex)0x84350499 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Fibre Channel Tape Drive Cleaning Required.
Log Message: The Fibre Channel tape drive on tape controller with world wide name “%4”, SCSI bus

%5, SCSI target %6, requires cleaning.
SNMP Trap: cpqFcTapeDriveCleaningRequired - 16012 in CPQFCA.MIB
Symptom: Fibre Channel Tape Drive Cleaning Required trap. The agent has detected a tape drive

that needs to have a cleaning tape inserted and run. This causes the tape drive heads to be cleaned.

Storage agents 53

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcTapeCntlrWWN

• cpqFcTapeDriveScsiBus

• cpqFcTapeDriveScsiTarget

• cpqFcTapeDriveScsiLun

Supporting SNMP Trap Description: “Cleaning is needed for tape drive.”

NT Event ID: 1178 (Hex)0x8435049a (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Fibre Channel Tape Drive Replace Cleaning Tape.
Log Message: The cleaning tape in the Fibre Channel tape drive on tape controller with world wide

name “%4”, SCSI bus %5, SCSI target %6, needs to be replaced.
SNMP Trap: cpqFcTapeDriveCleanTapeReplace - 16013 in CPQFCA.MIB
Symptom: Fibre Channel Tape Drive Cleaning Tape Needs Replacing. The agent has detected that an

autoloader tape unit has a cleaning tape that has been fully used and therefore needs to be replaced
with a new cleaning tape.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcTapeCntlrWWN

• cpqFcTapeDriveScsiBus

• cpqFcTapeDriveScsiTarget

• cpqFcTapeDriveScsiLun

Supporting SNMP Trap Description: “Cleaning tape needs replacing.”

NT Event ID: 1179 (Hex)0x8435049b (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: External Array Controller Active.
Log Message: The external controller in I/O slot %5 of array “%4” has become the active controller.
SNMP Trap: cpqFcaCntlrActive - 16014 in CPQFCA.MIB
Symptom: Fibre Array Controller Active. This trap indicates that the Storage Agent has detected that a

backup array controller in a duplexed pair has switched over to the active role. The variable
cpqFcaCntlrBoxIoSlot indicates the new active controller index.

User Action: Check the partner controller for problems. If this was the result of a user initiated switch­over, no action is required.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

Storage agents 54

• cpqFcaCntlrBoxIoSlot

Supporting SNMP Trap Description: “Controller in I/O slot [cpqFcaCntlrBoxIoSlot] is now active on
chassis [cpqSsChassisName].”

NT Event ID: 1180 (Hex)0x8435049c (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Tape Library Status Change.
Log Message: The tape library in slot %4, SCSI bus %5, SCSI target %6 has a new status of %7.
SNMP Trap: cpqDa2TapeLibraryStatusChange - 3031 in CPQIDA.MIB
Symptom: Tape Library Status Change. This trap indicates that the agent has detected a change in the

status of a tape library. The variable cpqDaTapeLibraryStatus indicates the current tape library status.
The variable cpqDaTapeLibraryScsiTarget indicates the SCSI ID of the tape library.

User Action: If the tape library is failed, check the tape library front panel.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaTapeLibraryCntlrIndex

• cpqDaTapeLibraryScsiBus

• cpqDaTapeLibraryScsiTarget

• cpqDaTapeLibraryScsiLun

• cpqDaTapeLibraryModel

• cpqDaTapeLibraryFWRev

• cpqDaTapeLibrarySerialNumber

• cpqDaTapeLibraryStatus

Supporting SNMP Trap Description: “Status is now [cpqDaTapeLibraryStatus] for the tape library.”

NT Event ID: 1181 (Hex)0x8435049d (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Tape Library Door Status Change.
Log Message: The tape library in slot %4, SCSI bus %5, SCSI target %6 has a new door status of %7.
SNMP Trap: cpqDaTapeLibraryDoorStatusChange - 3021 in CPQIDA.MIB
Symptom: Tape Library Door Status Change. This trap indicates that the agent has detected a change

in the door status of a tape library. The variable cpqDaTapeLibraryDoorStatus indicates the current
tape library door status. The variable cpqDaTapeLibraryScsiTarget indicates the SCSI ID of the tape
library.

User Action: If the tape library door is open, close the tape library door.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaTapeLibraryCntlrIndex

• cpqDaTapeLibraryScsiBus

• cpqDaTapeLibraryScsiTarget

Storage agents 55

• cpqDaTapeLibraryScsiLun

• cpqDaTapeLibraryDoorStatus

Supporting SNMP Trap Description: “The door is [cpqDaTapeLibraryDoorStatus] for tape library.”

NT Event ID: 1182 (Hex)0x8435049e (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Tape Drive Status Change.
Log Message: The tape drive in slot %4, SCSI bus %5, SCSI target %6 has a new status of %7.
SNMP Trap: cpqDa2TapeDriveStatusChange - 3032 in CPQIDA.MIB
Symptom: Tape Drive Status Change. This trap indicates that the agent has detected a change in the

status of a tape drive. The variable cpqDaTapeDrvStatus indicates the current tape status. The variable
cpqDaTapeDrvScsiIdIndex indicates the SCSI ID of the tape drive.

User Action: If the tape is failed, check the tape and all SCSI connections.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaTapeDrvCntlrIndex

• cpqDaTapeDrvBusIndex

• cpqDaTapeDrvScsiIdIndex

• cpqDaTapeDrvLunIndex

• cpqDaTapeDrvName

• cpqDaTapeDrvFwRev

• cpqDaTapeDrvSerialNumber

• cpqDaTapeDrvStatus

Supporting SNMP Trap Description: “Status is now [cpqDaTapeDrvStatus] for a tape drive.”

NT Event ID: 1183 (Hex)0x8435049f (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Tape Drive Cleaning Required.
Log Message: The tape drive in slot %4, SCSI bus %5, SCSI target %6 requires cleaning.
SNMP Trap: cpqDaTapeDriveCleaningRequired - 3023 in CPQIDA.MIB
Symptom: Tape Drive Cleaning Required trap. The agent has detected a tape drive that needs to have

a cleaning tape inserted and run. This causes the tape drive heads to be cleaned.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaTapeDrvCntlrIndex

• cpqDaTapeDrvBusIndex

• cpqDaTapeDrvScsiIdIndex

• cpqDaTapeDrvLunIndex

Supporting SNMP Trap Description: “Cleaning is needed for the tape drive.”

Storage agents 56

NT Event ID: 1184 (Hex)0x843504a0 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Tape Drive Replace Cleaning Tape.
Log Message: The cleaning tape in the tape drive in slot %4, SCSI bus %5, SCSI target %6 needs to

be replaced.
SNMP Trap: cpqDaTapeDriveCleanTapeReplace - 3024 in CPQIDA.MIB
Symptom: Tape Drive Cleaning Tape Needs Replacing. The agent has detected that an autoloader

tape unit has a cleaning tape that has been fully used and therefore needs to be replaced with a new
cleaning tape.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaTapeDrvCntlrIndex

• cpqDaTapeDrvBusIndex

• cpqDaTapeDrvScsiIdIndex

• cpqDaTapeDrvLunIndex

Supporting SNMP Trap Description: “Cleaning tape needs replacing.”

NT Event ID: 1185 (Hex)0x843504a1 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Fibre Channel Controller Status Change.
Log Message: The Fibre Channel Controller in slot %4 has a new status of %5.
SNMP Trap: cpqFca2HostCntlrStatusChange - 16021 in CPQFCA.MIB
Symptom: Fibre Channel Host Controller Status Change. This trap indicates that the agent has

detected a change in the status of a Fibre Channel Host Controller. The variable
cpqFcaHostCntlrStatus indicates the current controller status.

User Action: If the controller status is failed, replace the controller.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcaHostCntlrSlot

• cpqFcaHostCntlrStatus

• cpqFcaHostCntlrModel

• cpqFcaHostCntlrWorldWideName

Supporting SNMP Trap Description: “Host controller in slot [cpqFcaHostCntlrSlot] has a new status of
[cpqFcaHostCntlrStatus].”

NT Event ID: 1186 (Hex)0x843504a2 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: IDE ATA Disk Status Change.
Log Message: The ATA disk drive with model %6 and serial number %7 has a new status of %2.

Storage agents 57

SNMP Trap: cpqIdeAtaDiskStatusChange - 14004 in CPQIDE.MIB
Symptom: ATA Disk Status Change. This trap indicates that the agent has detected a change in the

status of an ATA disk drive. The variable cpqIdeAtaDiskStatus indicates the current disk drive status.
User Action: If the physical drive status is smartError(3) or failed(4), replace the drive.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqIdeAtaDiskControllerIndex

• cpqIdeAtaDiskIndex

• cpqIdeAtaDiskModel

• cpqIdeAtaDiskFwRev

• cpqIdeAtaDiskSerialNumber

• cpqIdeAtaDiskStatus

• cpqIdeAtaDiskChannel

• cpqIdeAtaDiskNumber

Supporting SNMP Trap Description: “Status is now [cpqIdeAtaDiskStatus] for the ATA disk.”

NT Event ID: 1187 (Hex)0x843504a3 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: ATA RAID Logical Drive Status Change.
Log Message: ATA RAID logical drive number %6 on the “%5” in slot %4 has a new status of %2.
SNMP Trap: cpqIdeLogicalDriveStatusChange - 14005 in CPQIDE.MIB
Symptom: IDE Logical Drive Status Change. This trap indicates that the agent has detected a change

in the status of an IDE logical drive. The variable cpqIdeLogicalDriveStatus indicates the current
logical drive status.

User Action: If the logical drive status is failed(5), examine the array for failed drives that need
replacement.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqIdeControllerModel

• cpqIdeControllerSlot

• cpqIdeLogicalDriveControllerIndex

• cpqIdeLogicalDriveIndex

• cpqIdeLogicalDriveStatus

Supporting SNMP Trap Description: “Status is now [cpqIdeLogicalDriveStatus] for the IDE logical
drive.”

NT Event ID: 1188 (Hex)0x843504a4 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Fan Status Change.

Storage agents 58

Log Message: An enclosure attached to port %5 of storage system “%4” has a new fan status of %7.
The enclosure model is “%6”.

SNMP Trap: cpqSsExBackplaneFanStatusChange - 8022 in CPQSTSYS.MIB
Symptom: Storage System Fan Status Change. The agent has detected a change in the fan status of a

storage system. The variable cpqSsBackplaneFanStatus indicates the current fan status.
User Action: If the fan status is degraded or failed, replace any failed fans.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqSsBackplaneIndex

• cpqSsBackplaneVendor

• cpqSsBackplaneModel

• cpqSsBackplaneSerialNumber

• cpqSsBackplaneFanStatus

Supporting SNMP Trap Description: “Storage system fan status changed to
[cpqSsBackplaneFanStatus].”

NT Event ID: 1189 (Hex)0x843504a5 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Temperature Status Change.
Log Message: An enclosure attached to port %5 of storage system “%4” has a new temperature status

of %7. The enclosure model is “%6”.
SNMP Trap: cpqSsExBackplaneTempStatusChange - 8023 in CPQSTSYS.MIB
Symptom: Storage System Temperature Status Change. The agent has detected a change in the status

of the temperature in a storage system. The variable cpqSsBackplaneTempStatus indicates the current
status.

User Action: If the temperature status is degraded or failed, shut down the storage system as soon as
possible. Be sure that the storage system environment is being cooled properly and that no
components are overheated.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqSsBackplaneIndex

• cpqSsBackplaneVendor

• cpqSsBackplaneModel

• cpqSsBackplaneSerialNumber

• cpqSsBackplaneTempStatus

Storage agents 59

Supporting SNMP Trap Description: “Storage system temperature status changed to
[cpqSsBackplaneTempStatus].”

NT Event ID: 1190 (Hex)0x843504a6 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Power Supply Status Change.
Log Message: An enclosure attached to port %5 of storage system “%4” has a new power supply

status of %7. The enclosure model is “%6”.
SNMP Trap: cpqSsExBackplanePowerSupplyStatusChange - 8024 in CPQSTSYS.MIB
Symptom: Storage System Power Supply Status Change. The agent has detected a change in the

power supply status of a storage system. The variable cpqSsBackplaneFtpsStatus indicates the current
status.

User Action: If the power supply status is degraded, restore power or replace the failed power supply.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqSsBackplaneIndex

• cpqSsBackplaneVendor

• cpqSsBackplaneModel

• cpqSsBackplaneSerialNumber

• cpqSsBackplaneFtpsStatus

Supporting SNMP Trap Description: “Storage system power supply status changed to
[cpqSsBackplaneFtpsStatus].”

NT Event ID: 1191 (Hex)0x843504a7 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: SCSI Tape Library Status Change.
Log Message: The tape library with SCSI target %6 connected to SCSI bus %5 of the controller in slot

%4 has a new status of %7.
SNMP Trap: cpqTapeLibraryStatusChange - 5018 in CPQSCSI.MIB
Symptom: Tape Library Status Change. The Storage Agent has detected a change in the status of a

tape library. The current tape library status is indicated in the cpqTapeLibraryState variable.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqTapeLibraryCntlrIndex

• cpqTapeLibraryBusIndex

• cpqTapeLibraryScsiIdIndex

• cpqTapeLibraryLunIndex

• cpqTapeLibraryName

Storage agents 60

• cpqTapeLibraryFwRev

• cpqTapeLibrarySerialNumber

• cpqTapeLibraryState

Supporting SNMP Trap Description: “Status is now [cpqTapeLibraryState].”

NT Event ID: 1192 (Hex)0x843504a8 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: SCSI Tape Drive Status Change.
Log Message: The tape drive with SCSI target %6 connected to SCSI bus %5 of the controller in slot

%4 has a new status of %2.
SNMP Trap: cpqTape5PhyDrvStatusChange - 5019 in CPQSCSI.MIB
Symptom: Tape Drive Status Change. The Storage Agent has detected a change in the status of a

tape drive. The current physical drive status is indicated in the cpqTapePhyDrvStatus variable.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqTapePhyDrvCntlrIndex

• cpqTapePhyDrvBusIndex

• cpqTapePhyDrvScsiIdIndex

• cpqTapePhyDrvLunIndex

• cpqTapePhyDrvName

• cpqTapePhyDrvFwRev

• cpqTapePhyDrvSerialNumber

• cpqTapePhyDrvStatus

Supporting SNMP Trap Description: “Status is now [cpqTapePhyDrvStatus].”

NT Event ID: 1193 (Hex)0x843504a9 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: External Tape Drive Status Change.
Log Message: The tape drive at location “%4”, has a new status of %7.
SNMP Trap: cpqExtTapeDriveStatusChange - 16023 in CPQFCA.MIB
Symptom: External Tape Drive Status Change. This trap indicates that the agent has detected a

change in the status of an External Tape Drive. The variable cpqFcTapeDriveStatus indicates the
current tape status.

User Action: If the tape is failed or is offline, check the tape and all connections.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcTapeDriveCntlrIndex

• cpqFcTapeDriveScsiBus

• cpqFcTapeDriveScsiTarget

• cpqFcTapeDriveScsiLun

Storage agents 61

• cpqFcTapeDriveModel

• cpqFcTapeDriveFWRev

• cpqFcTapeDriveSerialNumber

• cpqFcTapeDriveLocation

• cpqFcTapeDriveStatus

Supporting SNMP Trap Description: “Status is now [cpqFcTapeDriveStatus] for a tape drive.”

NT Event ID: 1194 (Hex)0x843504aa (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: External Tape Drive Cleaning Required.
Log Message: The tape drive at location “%4” requires cleaning.
SNMP Trap: cpqExtTapeDriveCleaningRequired - 16024 in CPQFCA.MIB
Symptom: External Tape Drive Cleaning Required trap. The agent has detected a tape drive that

needs to have a cleaning tape inserted and run. This causes the tape drive heads to be cleaned.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcTapeDriveCntlrIndex

• cpqFcTapeDriveScsiBus

• cpqFcTapeDriveScsiTarget

• cpqFcTapeDriveScsiLun

• cpqFcTapeDriveModel

• cpqFcTapeDriveFWRev

• cpqFcTapeDriveSerialNumber

• cpqFcTapeDriveLocation

Supporting SNMP Trap Description: “Cleaning is needed for tape drive.”

NT Event ID: 1195 (Hex)0x843504ab (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: External Tape Drive Replace Cleaning Tape.
Log Message: The cleaning tape in the tape drive at location “%4” needs to be replaced.
SNMP Trap: cpqExtTapeDriveCleanTapeReplace - 16025 in CPQFCA.MIB
Symptom: External Tape Drive Cleaning Tape Needs Replacing. The agent has detected that an

autoloader tape unit has a cleaning tape that has been fully used and therefore needs to be replaced
with a new cleaning tape.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcTapeDriveCntlrIndex

• cpqFcTapeDriveScsiBus

• cpqFcTapeDriveScsiTarget

• cpqFcTapeDriveScsiLun

Storage agents 62

• cpqFcTapeDriveModel

• cpqFcTapeDriveFWRev

• cpqFcTapeDriveSerialNumber

• cpqFcTapeDriveLocation

Supporting SNMP Trap Description: “Cleaning tape needs replacing.”

NT Event ID: 1196 (Hex)0x843504ac (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Recovery Server Option Status Change.
Log Message: Storage system “%4” has a new RSO status of %5.
SNMP Trap: cpqSsExRecoveryServerStatusChange - 8025 in CPQSTSYS.MIB
Symptom: Storage System Recovery Server Option Status Change. The agent has detected a change

in the recovery server option status of a storage system. The variable cpqSsChassisRsoStatus indicates
the current status.

User Action: If the RSO status is noSecondary(6) or linkDown(7), Be sure that the secondary server is
operational and that all cables are connected properly. If the RSO status is secondaryRunningAuto(8)
or secondaryRunningUser(9), examine the primary server for failed components.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsChassisName

• cpqSsChassisTime

• cpqSsChassisRsoStatus

• cpqSsChassisIndex

Supporting SNMP Trap Description: “Storage system recovery server option status changed to
[cpqSsChassisRsoStatus].”

NT Event ID: 1197 (Hex)0x843504ad (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: External Tape Library Status Change.
Log Message: The tape library at location “%4”, has a new status of %7.
SNMP Trap: cpqExtTapeLibraryStatusChange - 16026 in CPQFCA.MIB
Symptom: External Tape Library Status Change. This trap indicates that the agent has detected a

change in the status of an External Tape library. The variable cpqFcTapeLibraryStatus indicates the
current tape library status.

User Action: If the tape library is failed or is offline, check the tape library front panel and all
connections.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcTapeLibraryCntlrIndex

• cpqFcTapeLibraryScsiBus

Storage agents 63

• cpqFcTapeLibraryScsiTarget

• cpqFcTapeLibraryScsiLun

• cpqFcTapeLibraryModel

• cpqFcTapeLibraryFWRev

• cpqFcTapeLibrarySerialNumber

• cpqFcTapeLibraryLocation

• cpqFcTapeLibraryStatus

Supporting SNMP Trap Description: “Status is now [cpqFcTapeLibraryStatus] for the tape library.”

NT Event ID: 1198 (Hex)0x843504ae (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: External Tape Library Door Status Change.
Log Message: The tape library at location “%4”, has a new door status of %7.
SNMP Trap: cpqExtTapeLibraryDoorStatusChange - 16027 in CPQFCA.MIB
Symptom: External Tape Library Door Status Change. This trap indicates that the agent has detected a

change in the door status of an External Tape library. The variable cpqFcTapeLibraryDoorStatus
indicates the current tape library door status.

User Action: If the tape library door is open, close the tape library door.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcTapeLibraryCntlrIndex

• cpqFcTapeLibraryScsiBus

• cpqFcTapeLibraryScsiTarget

• cpqFcTapeLibraryScsiLun

• cpqFcTapeLibraryModel

• cpqFcTapeLibraryFWRev

• cpqFcTapeLibrarySerialNumber

• cpqFcTapeLibraryLocation

• cpqFcTapeLibraryDoorStatus

Supporting SNMP Trap Description: “The door is [cpqFcTapeLibraryDoorStatus] for tape library.”

NT Event ID: 1199 (Hex)0x843504af (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Controller Status Change.
Log Message: The Drive Array Controller in %7 has a new status of %5.
SNMP Trap: cpqDa6CntlrStatusChange - 3033 in CPQIDA.MIB
Symptom: Controller Status Change. This trap indicates that the agent has detected a change in the

status of a drive array controller. The variable cpqDaCntlrBoardStatus indicates the current controller
status.

Storage agents 64

User Action: If the board status is generalFailure(3), you may need to replace the controller. If the
board status is cableProblem(4), check the cable connections between the controller and the storage
system.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaCntlrIndex

• cpqDaCntlrBoardStatus

• cpqDaCntlrModel

• cpqDaCntlrSerialNumber

• cpqDaCntlrFWRev

• cpqDaAccelTotalMemory

Supporting SNMP Trap Description: “Status is now [cpqDaCntlrBoardStatus].”

Event Identifiers 1200-1294

NT Event ID: 1200 (Hex)0x843504b0 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Logical Drive Status Change.
Log Message: Logical drive number %5 on the array controller in %4 has a new status of %2.
SNMP Trap: cpqDa6LogDrvStatusChange - 3034 in CPQIDA.MIB
Symptom: Logical Drive Status Change. This trap indicates that the agent has detected a change in

the status of a drive array logical drive. The variable cpqDaLogDrvStatus indicates the current logical
drive status.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaLogDrvCntlrIndex

• cpqDaLogDrvIndex

• cpqDaLogDrvStatus

Supporting SNMP Trap Description: “Status is now [cpqDaLogDrvStatus].”

NT Event ID: 1201 (Hex)0x843504b1 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Spare Drive Status Change.
Log Message: The spare drive in %4, port %5, bay %6 has a new status of %2.
SNMP Trap: cpqDa6SpareStatusChange - 3035 in CPQIDA.MIB
Symptom: Spare Drive Status Change. This trap indicates that the agent has detected a change in the

status of a drive array spare drive. The variable cpqDaSpareStatus indicates the current spare drive
status.

Storage agents 65

User Action: If the spare drive status is failed, replace the drive.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaSpareCntlrIndex

• cpqDaSparePhyDrvIndex

• cpqDaSpareStatus

• cpqDaSpareBusNumber

• cpqDaSpareBay

Supporting SNMP Trap Description: “Spare Status is now [cpqDaSpareStatus].”

NT Event ID: 1202 (Hex)0x843504b2 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Physical Drive Status Change.
Log Message: The physical drive in %4, port %5, bay %6 with serial number “%7”, has a new status

of %2.
SNMP Trap: cpqDa6PhyDrvStatusChange - 3036 in CPQIDA.MIB
Symptom: Physical Drive Status Change. This trap indicates that the agent has detected a change in

the status of a drive array physical drive. The variable cpaDaPhyDrvStatus indicates the current
physical drive status.

User Action: If the physical drive status is failed(3) or predictive Failure(4), replace the drive.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaPhyDrvCntlrIndex

• cpqDaPhyDrvIndex

• cpqDaPhyDrvBusNumber

• cpqDaPhyDrvBay

• cpqDaPhyDrvModel

• cpqDaPhyDrvFWRev

• cpqDaPhyDrvSerialNum

• cpqDaPhyDrvFailureCode

• cpqDaPhyDrvStatus

Supporting SNMP Trap Description: “Physical Drive Status is now [cpqDaPhyDrvStatus].”

NT Event ID: 1203 (Hex)0x843504b3 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Physical Drive Threshold Exceeded.
Log Message: The physical drive in %4, port %5, bay %6 with serial number “%7”, has exceeded a

drive threshold.

Storage agents 66

SNMP Trap: cpqDa6PhyDrvThreshPassedTrap - 3037 in CPQIDA.MIB
Symptom: Physical Drive Threshold Passed. This trap indicates that the agent has detected a factory

threshold associated with one of the physical drive objects on a drive array has been exceeded.
User Action: Replace the physical drive.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaPhyDrvCntlrIndex

• cpqDaPhyDrvIndex

• cpqDaPhyDrvBusNumber

• cpqDaPhyDrvBay

• cpqDaPhyDrvModel

• cpqDaPhyDrvFWRev

• cpqDaPhyDrvSerialNum

Supporting SNMP Trap Description: “Factory threshold passed for a physical drive.”

NT Event ID: 1204 (Hex)0x843504b4 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Accelerator Status Change.
Log Message: The array accelerator board attached to the array controller in %4 has a new status of

%2.
SNMP Trap: cpqDa6AccelStatusChange - 3038 in CPQIDA.MIB
Symptom: Accelerator Board Status Change. This trap indicates that the agent has detected a change

in the status of an array accelerator cache board. The current status is represented by the variable
cpqDaAccelStatus.

User Action: If the accelerator board status is permDisabled(5), you may need to replace the
accelerator board.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaCntlrModel

• cpqDaAccelCntlrIndex

• cpqDaAccelSerialNumber

• cpqDaAccelTotalMemory

• cpqDaAccelStatus

• cpqDaAccelErrCode

Supporting SNMP Trap Description: “Status is now [cpqDaAccelStatus].”

NT Event ID: 1205 (Hex)0x843504b5 (cpqstmsg.dll)

Log Severity: Warning (2)

Storage agents 67

Event Title: Drive Array Accelerator Bad Data.
Log Message: The array accelerator board attached to the array controller in %4 is reporting that it

contains bad cached data.
SNMP Trap: cpqDa6AccelBadDataTrap - 3039 in CPQIDA.MIB
Symptom: Accelerator Board Bad Data. This trap indicates that the agent has detected an array

accelerator cache board that has lost battery power. If data was being stored in the accelerator
cache memory when the server lost power, that data has been lost.

User Action: Verify that no data has been lost.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaCntlrModel

• cpqDaAccelCntlrIndex

• cpqDaAccelSerialNumber

• cpqDaAccelTotalMemory

Supporting SNMP Trap Description: “Accelerator lost battery power. Data Loss possible.”

NT Event ID: 1206 (Hex)0x843504b6 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Accelerator Battery Failed.
Log Message: The array accelerator board attached to the array controller in %4 is reporting a

battery failure.
SNMP Trap: cpqDa6AccelBatteryFailed - 3040 in CPQIDA.MIB
Symptom: Accelerator Board Battery Failed. This trap indicates that the agent has detected a battery

failure associated with the array accelerator cache board.
User Action: Replace the Accelerator Cache Board.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaCntlrModel

• cpqDaAccelCntlrIndex

• cpqDaAccelSerialNumber

• cpqDaAccelTotalMemory

Supporting SNMP Trap Description: “Battery status is failed.”

Storage agents 68

NT Event ID: 1207 (Hex)0x843504b7 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Tape Library Status Change.
Log Message: The tape library in %4, SCSI bus %5, SCSI target %6 has a new status of %7.
SNMP Trap: cpqDa6TapeLibraryStatusChange - 3041 in CPQIDA.MIB
Symptom: Tape Library Status Change. This trap indicates that the agent has detected a change in the

status of a tape library. The variable cpqDaTapeLibraryStatus indicates the current tape library status.
The variable cpqDaTapeLibraryScsiTarget indicates the SCSI ID of the tape library.

User Action: If the tape library is failed, check the tape library front panel.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaTapeLibraryCntlrIndex

• cpqDaTapeLibraryScsiBus

• cpqDaTapeLibraryScsiTarget

• cpqDaTapeLibraryScsiLun

• cpqDaTapeLibraryModel

• cpqDaTapeLibraryFWRev

• cpqDaTapeLibrarySerialNumber

• cpqDaTapeLibraryStatus

Supporting SNMP Trap Description: “Status is now [cpqDaTapeLibraryStatus] for the tape library.”

NT Event ID: 1208 (Hex)0x843504b8 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Tape Library Door Status Change.
Log Message: The tape library in %4, SCSI bus %5, SCSI target %6 has a new door status of %7.
SNMP Trap: cpqDa6TapeLibraryDoorStatusChange - 3042 in CPQIDA.MIB
Symptom: Tape Library Door Status Change. This trap indicates that the agent has detected a change

in the door status of a tape library. The variable cpqDaTapeLibraryDoorStatus indicates the current
tape library door status. The variable cpqDaTapeLibraryScsiTarget indicates the SCSI ID of the tape
library.

User Action: If the tape library door is open, close the tape library door.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaTapeLibraryCntlrIndex

• cpqDaTapeLibraryScsiBus

• cpqDaTapeLibraryScsiTarget

• cpqDaTapeLibraryScsiLun

Storage agents 69

• cpqDaTapeLibraryModel

• cpqDaTapeLibraryFWRev

• cpqDaTapeLibrarySerialNumber

• cpqDaTapeLibraryDoorStatus

Supporting SNMP Trap Description: “The door is [cpqDaTapeLibraryDoorStatus] for tape library.”

NT Event ID: 1209 (Hex)0x843504b9 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Tape Drive Status Change.
Log Message: The tape drive in %4, SCSI bus %5, SCSI target %6 has a new status of %7.
SNMP Trap: cpqDa6TapeDriveStatusChange - 3043 in CPQIDA.MIB
Symptom: Tape Drive Status Change. This trap indicates that the agent has detected a change in the

status of a tape drive. The variable cpqDaTapeDrvStatus indicates the current tape status. The variable
cpqDaTapeDrvScsiIdIndex indicates the SCSI ID of the tape drive.

User Action: If the tape is failed, check the tape and all SCSI connections.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaTapeDrvCntlrIndex

• cpqDaTapeDrvBusIndex

• cpqDaTapeDrvScsiIdIndex

• cpqDaTapeDrvLunIndex

• cpqDaTapeDrvName

• cpqDaTapeDrvFwRev

• cpqDaTapeDrvSerialNumber

• cpqDaTapeDrvStatus

Supporting SNMP Trap Description: “Status is now [cpqDaTapeDrvStatus] for a tape drive.”

NT Event ID: 1210 (Hex)0x843504ba (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Tape Drive Cleaning Required.
Log Message: The tape drive in %4, SCSI bus %5, SCSI target %6 requires cleaning.
SNMP Trap: cpqDa6TapeDriveCleaningRequired - 3044 in CPQIDA.MIB
Symptom: Tape Drive Cleaning Required trap. The agent has detected a tape drive that needs to have

a cleaning tape inserted and run. This causes the tape drive heads to be cleaned.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaTapeDrvCntlrIndex

Storage agents 70

• cpqDaTapeDrvBusIndex

• cpqDaTapeDrvScsiIdIndex

• cpqDaTapeDrvLunIndex

• cpqDaTapeDrvName

• cpqDaTapeDrvFwRev

• cpqDaTapeDrvSerialNumber

Supporting SNMP Trap Description: “Cleaning is needed for the tape drive.”

NT Event ID: 1211 (Hex)0x843504bb (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Tape Drive Replace Cleaning Tape.
Log Message: The cleaning tape in the tape drive in %4, SCSI bus %5, SCSI target %6 needs to be

replaced.
SNMP Trap: cpqDa6TapeDriveCleanTapeReplace - 3045 in CPQIDA.MIB
Symptom: Tape Drive Cleaning Tape Needs Replacing. The agent has detected that an autoloader

tape unit has a cleaning tape that has been fully used and therefore needs to be replaced with a new
cleaning tape.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaTapeDrvCntlrIndex

• cpqDaTapeDrvBusIndex

• cpqDaTapeDrvScsiIdIndex

• cpqDaTapeDrvLunIndex

• cpqDaTapeDrvName

• cpqDaTapeDrvFwRev

• cpqDaTapeDrvSerialNumber

Supporting SNMP Trap Description: “Cleaning tape needs replacing.”

NT Event ID: 1212 (Hex)0x843504bc (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Fan Status Change.
Log Message: The %6 %7 storage system connected to SCSI bus %5 of the controller in %4 has a

new status of %2.
SNMP Trap: cpqSs5FanStatusChange - 8026 in CPQSTSYS.MIB
Symptom: Storage System fan status change. The agent has detected a change in the Fan Status of a

storage system. The variable cpqSsBoxFanStatus indicates the current fan status.
User Action: If the fan status is degraded or failed, replace any failed fans.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Storage agents 71

• cpqSsBoxCntlrHwLocation

• cpqSsBoxCntlrIndex

• cpqSsBoxBusIndex

• cpqSsBoxVendor

• cpqSsBoxModel

• cpqSsBoxSerialNumber

• cpqSsBoxFanStatus

Supporting SNMP Trap Description: “Storage System fan status changed to [cpqSsBoxFanStatus].”

NT Event ID: 1213 (Hex)0x843504bd (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Temperature Status Change.
Log Message: The %6 %7 storage system connected to SCSI bus %5 of the controller in %4 has a

new temperature status of %2.
SNMP Trap: cpqSs5TempStatusChange - 8027 in CPQSTSYS.MIB
Symptom: Storage System Temperature Status Change. The agent has detected a change in the

temperature status of a storage system. The variable cpqSsBoxTempStatus indicates the current
temperature status.

User Action: If the temperature status is degraded or failed, shut down the storage system as soon as
possible. Be sure that the storage system environment is being cooled properly and that no
components are overheated.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsBoxCntlrHwLocation

• cpqSsBoxCntlrIndex

• cpqSsBoxBusIndex

• cpqSsBoxVendor

• cpqSsBoxModel

• cpqSsBoxSerialNumber

• cpqSsBoxTempStatus

Supporting SNMP Trap Description: “Storage System temperature status changed to
[cpqSsBoxTempStatus].”

NT Event ID: 1214 (Hex)0x843504be (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Fault Tolerant Power Supply Status Change.
Log Message: The fault tolerant power supply in the %6 %7 storage system connected to SCSI bus %5

of the controller in %4 has a new status of %2.
SNMP Trap: cpqSs5PwrSupplyStatusChange - 8028 in CPQSTSYS.MIB
Symptom: Storage System Fault Tolerant Power Supply Status Change. The agent has detected a

change in the power supply status of a storage system. The variable cpqSsBoxFltTolPwrSupplyStatus
indicates the current power supply status.

Storage agents 72

User Action: If the power supply status is degraded, restore power or replace the failed power supply.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsBoxCntlrHwLocation

• cpqSsBoxCntlrIndex

• cpqSsBoxBusIndex

• cpqSsBoxVendor

• cpqSsBoxModel

• cpqSsBoxSerialNumber

• cpqSsBoxFltTolPwrSupplyStatus

Supporting SNMP Trap Description: “Storage system power supply status changed to
[cpqSsBoxFltTolPwrSupplyStatus].”

NT Event ID: 1215 (Hex)0x843504bf (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Fibre Channel Controller Status Change.
Log Message: The Fibre Channel Controller in %4 has a new status of %5.
SNMP Trap: cpqFca3HostCntlrStatusChange - 16028 in CPQFCA.MIB
Symptom: Fibre Channel Host Controller Status Change. This trap indicates that the agent has

detected a change in the status of a Fibre Channel Host Controller. The variable
cpqFcaHostCntlrStatus indicates the current controller status.

User Action: If the controller status is failed, replace the controller.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqFcaHostCntlrHwLocation

• cpqFcaHostCntlrIndex

• cpqFcaHostCntlrStatus

• cpqFcaHostCntlrModel

• cpqFcaHostCntlrSerialNumber

• cpqFcaHostCntlrWorldWideName

• cpqFcaHostCntlrWorldWidePortName

Supporting SNMP Trap Description: “Host controller has a new status of [cpqFcaHostCntlrStatus].”

NT Event ID: 1216 (Hex)0x843504c0 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Physical Drive Status Change.
Log Message: The physical drive in %4, %5 with serial number “%7”, has a new status of %2.
SNMP Trap: cpqDa7PhyDrvStatusChange - 3046 in CPQIDA.MIB

Storage agents 73

Symptom: Physical Drive Status Change. This trap indicates that the agent has detected a change in
the status of a drive array physical drive. The variable cpqDaPhyDrvStatus indicates the current
physical drive status.

User Action: If the physical drive status is failed (3) or predictiveFailure (4), replace the drive.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaPhyDrvCntlrIndex

• cpqDaPhyDrvIndex

• cpqDaPhyDrvLocationString

• cpqDaPhyDrvType

• cpqDaPhyDrvModel

• cpqDaPhyDrvFWRev

• cpqDaPhyDrvSerialNum

• cpqDaPhyDrvFailureCode

• cpqDaPhyDrvStatus

• cpqDaPhyDrvBusNumber

Supporting SNMP Trap Description: “Physical Drive Status is now [cpqDaPhyDrvStatus].”

NT Event ID: 1217 (Hex)0x843504c1 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Drive Array Spare Drive Status Change.
Log Message: The spare drive in %4, %5 has a new status of %2.
SNMP Trap: cpqDa7SpareStatusChange - 3047 in CPQIDA.MIB
Symptom: Spare Drive Status Change. This trap indicates that the agent has detected a change in the

status of a drive array spare drive. The variable cpqDaSpareStatus indicates the current spare drive
status.

User Action: If the spare drive status is failed, replace the drive.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqDaCntlrHwLocation

• cpqDaSpareCntlrIndex

• cpqDaSparePhyDrvIndex

• cpqDaSpareStatus

• cpqDaSpareLocationString

• cpqDaSpareDrvBusNumber

Supporting SNMP Trap Description: “Spare Status is now [cpqDaSpareStatus].”

Storage agents 74

NT Event ID: 1218 (Hex)0x843504c2 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Fan Status Change.
Log Message: The %6 %7 storage system connected to %5 of the controller in%4 has a new status of

%2.
SNMP Trap: cpqSs6FanStatusChange - 8029 in CPQSTSYS.MIB
Symptom: Storage System Fan Status Change. The agent has detected a change in the fan status of a

storage system. The variable cpqSsBoxFanStatus indicates the current fan status.
User Action: If the fan status is degraded or failed, replace any failed fans.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsBoxCntlrHwLocation

• cpqSsBoxCntlrIndex

• cpqSsBoxBusIndex

• cpqSsBoxVendor

• cpqSsBoxModel

• cpqSsBoxSerialNumber

• cpqSsBoxFanStatus

• cpqSsBoxLocationString

Supporting SNMP Trap Description: “Storage System fan status changed to [cpqSsBoxFanStatus].”

NT Event ID: 1219 (Hex)0x843504c3 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Temperature Status Change.
Log Message: The %6 %7 storage system connected to %5 of the controller in%4 has a new

temperature status of %2.
SNMP Trap: cpqSs6TempStatusChange - 8030 in CPQSTSYS.MIB
Symptom: Storage System Temperature Status Change. The agent has detected a change in the

temperature status of a storage system. The variable cpqSsBoxTempStatus indicates the current
temperature status.

User Action: If the temperature status is degraded or failed, shut down the storage system as soon as
possible. Be sure that the storage system environment is being cooled properly and that no
components are overheated.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsBoxCntlrHwLocation

• cpqSsBoxCntlrIndex

• cpqSsBoxBusIndex

• cpqSsBoxVendor

Storage agents 75

• cpqSsBoxModel

• cpqSsBoxSerialNumber

• cpqSsBoxTempStatus

• cpqSsBoxLocationString

Supporting SNMP Trap Description: “Storage System temperature status changed to
[cpqSsBoxTempStatus].”

NT Event ID: 1220 (Hex)0x843504c4 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: Storage System Fault Tolerant Power Supply Status Change.
Log Message: The fault tolerant power supply in the %6 %7 storage system connected to %5 of the

controller in%4 has a new status of %2.
SNMP Trap: cpqSs6PwrSupplyStatusChange - 8031 in CPQSTSYS.MIB
Symptom: Storage System Fault Tolerant Power Supply Status Change. The agent has detected a

change in the power supply status of a storage system. The variable cpqSsBoxFltTolPwrSupplyStatus
indicates the current power supply status.

User Action: If the power supply status is degraded, restore power or replace the failed power supply.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSsBoxCntlrHwLocation

• cpqSsBoxCntlrIndex

• cpqSsBoxBusIndex

• cpqSsBoxVendor

• cpqSsBoxModel

• cpqSsBoxSerialNumber

• cpqSsBoxFltTolPwrSupplyStatus

• cpqSsBoxLocationString

Supporting SNMP Trap Description: “Storage System power supply status changed to
[cpqSsBoxFltTolPwrSupplyStatus].”

NT Event ID: 1221 (Hex)0x843504c5 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: SAS/SATA Physical Drive Status Change.
Log Message: The physical drive in %4, %5 with serial number “%6”, has a new status of %7.
SNMP Trap: cpqSasPhyDrvStatusChange - 5022 in CPQSCSI.MIB
Symptom: Physical Drive Status Change. The Storage Agent has detected a change in the status of a

SAS or SATA physical drive. The current physical drive status is indicated in the cpqSasPhyDrvStatus
variable.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Storage agents 76

• cpqSasHbaHwLocation

• cpqSasPhyDrvLocationString

• cpqSasPhyDrvHbaIndex

• cpqSasPhyDrvIndex

• cpqSasPhyDrvStatus

• cpqSasPhyDrvType

• cpqSasPhyDrvModel

• cpqSasPhyDrvFWRev

• cpqSasPhyDrvSerialNumber

• cpqSasPhyDrvSasAddress

Supporting SNMP Trap Description: “Status is now [cpqSasPhyDrvStatus].”

NT Event ID: 1222 (Hex)0x843504c6 (cpqstmsg.dll)

Log Severity: Warning (2)
Event Title: SAS/SATA Logical Drive Status Change.
Log Message: Logical drive number %5 on the HBA in %4 has a new status of %6.
SNMP Trap: cpqSasLogDrvStatusChange - 5023 in CPQSCSI.MIB
Symptom: Logical Drive Status Change. The Storage Agent has detected a change in the status of a

SAS or SATA logical drive. The current logical drive status is indicated in the cpqSasLogDrvStatus
variable.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSasHbaHwLocation

• cpqSasLogDrvHbaIndex

• cpqSasLogDrvIndex

• cpqSasLogDrvStatus

• cpqSasLogDrvOsName

Supporting SNMP Trap Description: “Status is now [cpqSasLogDrvStatus].”

Event identifier: cpqstmsg.dll - 1280 (Hex)0x84350500 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to allocate memory. This indicates a low memory condition. Rebooting the

system will correct this error.

Event identifier: cpqstmsg.dll - 1281 (Hex)0x84350501 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read from the registry subkey. This error can be caused by a corrupt registry

or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 1282 (Hex)0x84350502 (Service Event)

Log Severity: Warning (2)
Log Message: Could not write the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Storage agents 77

Event identifier: cpqstmsg.dll - 1283 (Hex)0x84350503 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 1284 (Hex)0x84350504 (Service Event)

Log Severity: Warning (2)
Log Message: Could not write the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 1285 (Hex)0x84350505 (Service Event)

Log Severity: Warning (2)
Log Message: Could not write the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 1294 (Hex)0x8435050e (Service Event)

Log Severity: Warning (2)
Log Message: Unsupported storage system. The ProLiant storage system %1 is unsupported by this

version of the Storage Agents. Upgrade the agents to the latest version.

Event Identifiers 1343-4613

Event identifier: cpqstmsg.dll - 1343 (Hex)0x8435053f (Service Event)

Log Severity: Warning (2)
Log Message: Duplicate SCSI port found in slot %1. The current system ROM may not support this

SCSI controller. You may need to update your system ROM.

Event identifier: cpqstmsg.dll - 1344 (Hex)0x84350540 (Service Event)

Log Severity: Warning (2)
Log Message: A version mismatch has been detected with the SCSI device monitor driver

(CPQSDM.SYS). The current driver version is %1. Cause: You may not have rebooted after a Storage
Agents upgrade. Always reboot the system after installing agents.

Event identifier: cpqstmsg.dll – 1346 (Hex) 0x84350540 (Service Event)

Log Severity: Warning (2)
Log Message: The SCSI controller on port %1 has been omitted. The SCSI Agent could not get the slot

data for the controller.

Event identifier: cpqstmsg.dll - 1792 (Hex)0x84350700 (Service Event)

Log Severity: Warning (2)
Log Message: The SNMP Agent is unable to generate traps due to an error during initialization.

Cause: Check to Be sure that the SNMP service is running. Reinstalling the agents may fix this error.

Event identifier: cpqstmsg.dll - 1795 (Hex)0x84350703 (Service Event)

Log Severity: Warning (2)

Storage agents 78

Log Message: The SNMP Agent is older than other components. The SNMP Agent is older than the
other components of the Storage Agents. Reinstall the entire Storage Agents package to correct this
error.

Event identifier: cpqstmsg.dll - 1796 (Hex)0x84350704 (Service Event)

Log Severity: Warning (2)
Log Message: The %1 Agent is older than other components. The %1 Agent is older than the other

components of the Storage Agents. Reinstall the entire Storage Agents package to correct this error.

Event identifier: cpqstmsg.dll - 1800 (Hex)0x84350708 (Service Event)

Log Severity: Warning (2)
Log Message: Unable to read security configuration information. SNMP sets have been disabled.

Cause: This can be cause by an invalid or missing configuration or by a corrupt registry. Reinstalling
the Storage Agents may correct this problem.

Event identifier: cpqstmsg.dll - 1803 (Hex)0xc435070b (Service Event)

Log Severity: Error (3)
Log Message: Unable to load a required library. This error can be caused by a corrupt or missing

file. Reinstalling the Storage Agents or running the Emergency Repair procedure may correct this
error.

Event identifier: cpqstmsg.dll - 1804 (Hex)0x8435070c (Service Event)

Log Severity: Warning (2)
Log Message: The Storage SNMP Agent was unable to forward an SNMP trap to the Remote Insight

Board trap due to processing error. The data contains the error code.

Event identifier: cpqstmsg.dll - 1806 (Hex)0x8435070e (Service Event)

Log Severity: Warning (2)
Log Message: The Storage Agent service is not running. The SNMP Agent has determined that the

Storage Agent service is not running. Stop the SNMP service and restart the Storage Agents service. If
the error persists, reinstalling the Storage Agents may correct this error.

Event identifier: cpqstmsg.dll - 1807 (Hex)0x4435070f (Service Event)

Log Severity: Information (1)
Log Message: The Storage SNMP Agent has determined the Storage Agents service is running.

Event identifier: cpqstmsg.dll - 1808 (Hex)0x44350710 (Service Event)

Log Severity: Information (1)
Log Message: The agent could not deliver trap %1. The agent was unable to use Asynchronous

Management to deliver a trap. This can be caused by a failure in the Remote Access Service or by a
missing or invalid configuration. Use the HP Insight Management Agents control panel to verify the
Asynchronous Management configuration settings. Use the Network control panel to verify the Remote
Access configuration. If this error persists, reinstalling the Storage Agents or the Remote Access
Service may correct this error. For more information, see the Insight Asynchronous Management
documentation.

Event identifier: cpqstmsg.dll - 3584 (Hex)0x84350e00 (Service Event)

Log Severity: Warning (2)

Storage agents 79

Log Message: The IDE Agent could not allocate memory. The data contains the error code.

Event identifier: cpqstmsg.dll - 3585 (Hex)0x84350e01 (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent could not open the base of the registry. The data contains the error

code.

Event identifier: cpqstmsg.dll - 3586 (Hex)0x84350e02 (Service Event)

Log Severity: Warning (2)
Log Message: “%1”. The data contains the error code.

Event identifier: cpqstmsg.dll - 3587 (Hex)0x84350e03 (Service Event)

Log Severity: Warning (2)
Log Message: “%1”. The data contains the error code.

Event identifier: cpqstmsg.dll - 3588 (Hex)0x84350e04 (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent could not read the registry value “%1”. The data contains the error

code.

Event identifier: cpqstmsg.dll - 3589 (Hex)0x84350e05 (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent found an incorrect type for registry value “%1”. The data contains the

type found.

Event identifier: cpqstmsg.dll - 3590 (Hex)0x84350e06 (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent could not create an event. The data contains the error code.

Event identifier: cpqstmsg.dll - 3591 (Hex)0x84350e07 (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent could not open an event. The data contains the error code.

Event identifier: cpqstmsg.dll - 3592 (Hex)0x84350e08 (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent could not set an event. The data contains the error code.

Event identifier: cpqstmsg.dll - 3593 (Hex)0x84350e09 (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent could not create a mutex. The data contains the error code.

Event identifier: cpqstmsg.dll - 3594 (Hex)0x84350e0a (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent could not open a mutex. The data contains the error code.

Event identifier: cpqstmsg.dll - 3595 (Hex)0x84350e0b (Service Event)

Log Severity: Warning (2)

Storage agents 80

Log Message: The IDE Agent could not create its main thread of execution. The data contains the
error code.

Event identifier: cpqstmsg.dll - 3596 (Hex)0x84350e0c (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent main thread did not terminate properly. The data contains the error

code.

Event identifier: cpqstmsg.dll - 3597 (Hex)0x84350e0d (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent got an unexpected error code while waiting for an event. The data

contains the error code.

Event identifier: cpqstmsg.dll - 3598 (Hex)0x84350e0e (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent got an unexpected error code while waiting for multiple events. The

data contains the error code.

Event identifier: cpqstmsg.dll - 3599 (Hex)0x84350e0f (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent did not respond to a request. The data contains the error code.

Event identifier: cpqstmsg.dll - 3600 (Hex)0x84350e10 (Service Event)

Log Severity: Warning (2)
Log Message: The IDE Agent received an unknown action code from the service. The data contains

the action code.

Event identifier: cpqstmsg.dll - 4097 (Hex)0x84351001 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read from the registry subkey. This error can be caused by a corrupt registry

or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4098 (Hex)0x84351002 (Service Event)

Log Severity: Warning (2)
Log Message: Could not write the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4099 (Hex)0x84351003 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4100 (Hex)0x84351004 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4101 (Hex)0x84351005 (Service Event)

Storage agents 81

Log Severity: Warning (2)
Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4609 (Hex)0x84351201 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry subkey. This error can be caused by a corrupt registry or a

low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4610 (Hex)0x84351202 (Service Event)

Log Severity: Warning (2)
Log Message: Could not write the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4611 (Hex)0x84351203 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4612 (Hex)0x84351204 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4613 (Hex)0x84351205 (Service Event)

Log Severity: Warning (2)
Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt

registry or a low memory condition. Rebooting the server may correct this error.

Server agents 82

Server agents

Event Identifiers 256-774

Event identifier: cpqsvmsg.dll - 256 (Hex)0x84350100 (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service detected an error. The insertion string is: %1. The data

contains the error code.

Event identifier: cpqsvmsg.dll - 257 (Hex)0x84350101 (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not allocate memory. The data contains the error code.

Event identifier: cpqsvmsg.dll - 258 (Hex)0x84350102 (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not register with the Service Control Manager. The

data contains the error code.

Event identifier: cpqsvmsg.dll - 259 (Hex)0x84350103 (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not set the service status with the Service Control

Manager. The data contains the error code.

Event identifier: cpqsvmsg.dll - 260 (Hex)0x84350104 (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not create an event object. The data contains the error

code.

Event identifier: cpqsvmsg.dll - 261 (Hex)0x84350105 (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not open registry key “%1”. The data contains the

error code.

Event identifier: cpqsvmsg.dll - 262 (Hex)0x84350106 (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not start any agents successfully.

Event identifier: cpqsvmsg.dll - 263 (Hex)0x84350107 (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not read the registry value “%1”. The data contains the

error code.

Event identifier: cpqsvmsg.dll - 264 (Hex)0x84350108 (Service Event)

Server agents 83

Log Severity: Warning (2)
Log Message: The Server Agents service could not load the module “%1”. The data contains the error

code.

Event identifier: cpqsvmsg.dll - 265 (Hex)0x84350109 (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not get the control function for module “%1”. The data

contains the error code.

Event identifier: cpqsvmsg.dll - 266 (Hex)0x8435010a (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not initialize agent “%1”. The data contains the error

code.

Event identifier: cpqsvmsg.dll - 267 (Hex)0x8435010b (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not start agent “%1”. The data contains the error code.

Event identifier: cpqsvmsg.dll - 268 (Hex)0x8435010c (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service detected an invalid state for agent “%1”. The data contains

the state.

Event identifier: cpqsvmsg.dll - 269 (Hex)0x8435010d (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not stop agent “%1”. The data contains the error code.

Event identifier: cpqsvmsg.dll - 270 (Hex)0x8435010e (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not terminate agent “%1”. The data contains the error

code.

Event identifier: cpqsvmsg.dll - 271 (Hex)0x8435010f (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not unload the module “%1”. The data contains the

error code.

Event identifier: cpqsvmsg.dll - 272 (Hex)0x84350110 (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not create the registry key “%1”. The data contains the

error code.

Event identifier: cpqsvmsg.dll - 273 (Hex)0x84350111 (Service Event)

Log Severity: Warning (2)
Log Message: The Server Agents service could not write the registry value “%1”. The data contains

the error code.

Event identifier: cpqsvmsg.dll - 399 (Hex)0xc435018f (Service Event)

Server agents 84

Log Severity: Error (3)
Log Message: The Server Agents service encountered a fatal error. The service is terminating. The

data contains the error code.

Event identifier: cpqsvmsg.dll - 400 (Hex)0x44350190 (Service Event)

Log Severity: Information (1)
Log Message: The Server Agents service version %1 has started.

Event identifier: cpqsvmsg.dll - 401 (Hex)0x44350191 (Service Event)

Log Severity: Information (1)
Log Message: %1

Event identifier: cpqsvmsg.dll - 768 (Hex)0x84350300 (Service Event)

Log Severity: Warning (2)
Log Message: The Remote Alerter Agent detected an invalid data type within an alert definition.

Event identifier: cpqsvmsg.dll - 769 (Hex)0x84350301 (Service Event)

Log Severity: Warning (2)
Log Message: The Remote Alerter Agent detected an error while attempting to log an alert remotely.

The data contains the error code.

Event identifier: cpqsvmsg.dll - 770 (Hex)0x84350302 (Service Event)

Log Severity: Warning (2)
Log Message: The Remote Alerter Agent detected an error while attempting to retrieve data from key

= %1 in the registry. The data contains the error code.

Event identifier: cpqsvmsg.dll - 771 (Hex)0x84350303 (Service Event)

Log Severity: Warning (2)
Log Message: The Remote Alerter Agent was unable to log an event in the event log of the system

named %1. The data contains the error code.

Event identifier: cpqsvmsg.dll - 772 (Hex)0xc4350304 (Service Event)

Log Severity: Error (3)
Log Message: The Remote Alerter Agent detected a null handle on initialization. The data contains the

error code.

Event identifier: cpqsvmsg.dll - 773 (Hex)0xc4350305 (Service Event)

Log Severity: Error (3)
Log Message: The Remote Alerter Agent received an error on WaitForMultipleObjects call. The data

contains the error code.

Event identifier: cpqsvmsg.dll - 774 (Hex)0xc4350306 (Service Event)

Log Severity: Error (3)
Log Message: The Remote Alerter Agent received an error on ResetEvent call. The data contains the

error code.

Server agents 85

Event Identifiers 1024-1092

NT Event ID: 1024 (Hex)0xc4350400 (cpqsvmsg.dll)

Log Severity: Error (3)
Log Message: A cache accelerator parity error indicates a cache module needs to be replaced.
SNMP Trap: cpqHe3CacheAccelParityError - 6046 in CPQHLTH.MIB
Symptom: A cache accelerator parity error indicates that a cache module needs to be replaced. The

error information is reported in the variable cpqHeEventLogErrorDesc.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “Cache Accelerator errors may require a replacement module.”

NT Event ID: 1025 (Hex)0x84350401 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Advanced Memory Protection subsystem has detected a memory fault. The Online

Spare Memory has been activated. Schedule server down time to replace the memory.
SNMP Trap: cpqHeResilientMemOnlineSpareEngaged - 6047 in CPQHLTH.MIB
Symptom: Advanced Memory Protection Online Spare Engaged. The Advanced Memory Protection

subsystem has detected a memory fault. The Online Spare Memory has been activated.
User Action: Schedule server down time to replace the faulty memory.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “The Advanced Memory Protection subsystem has engaged the
online spare memory.”

NT Event ID: 1026 (Hex)0x84350402 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Advanced Memory Protection sub-system has detected a memory fault. The

Mirrored Memory has been activated. Schedule server down time to replace the memory.
SNMP Trap: cpqHeResilientMemMirroredMemoryEngaged - 6051 in CPQHLTH.MIB
Symptom: Advanced Memory Protection Mirrored Memory Engaged. The Advanced Memory

Protection subsystem has detected a memory fault. Mirrored Memory has been activated.
User Action: Replace the faulty memory.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “The Advanced Memory Protection subsystem has engaged the
online spare memory.”

Server agents 86

NT Event ID: 1027 (Hex)0x84350403 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Advanced Memory Protection sub-system has detected a memory fault. Advanced

ECC has been activated. Schedule server down time to replace the memory.
SNMP Trap: cpqHeResilientAdvancedECCMemoryEngaged - 6052 in CPQHLTH.MIB
Symptom: Advanced Memory Protection Advanced ECC Memory Engaged. The Advanced Memory

Protection subsystem has detected a memory fault. Advanced ECC has been activated.
User Action: Replace the faulty memory.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “The Advanced Memory Protection subsystem has engaged the
advanced ECC memory.”

NT Event ID: 1028 (Hex)0x84350404 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Advanced Memory Protection sub-system has detected a memory fault. The XOR

recovery engine has been activated. Schedule server down time to replace the memory.
SNMP Trap: cpqHeResilientMemXorMemoryEngaged - 6053 in CPQHLTH.MIB
Symptom: Advanced Memory Protection XOR Engine Memory Engaged. The Advanced Memory

Protection subsystem has detected a memory fault. The XOR engine has been activated.
User Action: Replace the faulty memory.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “The Advanced Memory Protection subsystem has engaged the
XOR memory.”

NT Event ID: 1029 (Hex)0x44350405 (cpqsvmsg.dll)

Log Severity: Information (1)
Log Message: The Fault Tolerant Power Supply Sub-system has returned to a redundant state.
SNMP Trap: cpqHe3FltTolPowerRedundancyRestored - 6054 in CPQHLTH.MIB
Symptom: The Fault Tolerant Power Supplies have returned to a redundant state for the specified

chassis.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolPowerSupplyChassis

Supporting SNMP Trap Description: “The Power Supplies are now redundant on Chassis
[cpqHeFltTolPowerSupplyChassis].”

Server agents 87

NT Event ID: 1030 (Hex) 0x44350406 (cpqsvmsg.dll)

Log Severity: Information (1)
Log Message: The Fan Sub-system has returned to a redundant state.
SNMP Trap: cpqHe3FltTolFanRedundancyRestored - 6055 in CPQHLTH.MIB
Symptom: The Fault Tolerant Fans have returned to a redundant state for the specified chassis.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolFanChassis

Supporting SNMP Trap Description: “The Fans are now redundant on Chassis
[cpqHeFltTolFanChassis].”

NT Event ID: 1035 (Hex) 0x8435040BL (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: Correctable or Uncorrectable memory error detected. The memory module should be

replaced.
SNMP Trap: cpqHe5CorrMemReplaceMemModule - 6064 in CPQHLTH.MIB
Symptom: Corrected Memory Errors Detected. The errors have been corrected, but the memory

module should be replaced. Value 0 for CPU means memory is not processor-based.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeResMem2BoardNum

• cpqHeResMem2CpuNum

• cpqHeResMem2RiserNum

• cpqHeResMem2ModuleNum

• cpqHeResMem2ModulePartNo

• cpqHeResMem2ModuleSize

• cpqSiServerSystemId

Supporting SNMP Trap Description: “Correctable memory errors require a replacement of the
memory module in slot [cpqHeResMem2BoardNum], socket [cpqHeResMem2ModuleNum], Cpu
[cpqHeResMem2CpuNum] Riser [cpqHeResMem2RiserNum].”

NT Event ID: 1036 (Hex) 0x4435040CL (cpqsvmsg.dll)

Log Severity: Informational (1)
Log Message: A memory board or cartridge has been removed from the system. Please reinsert the

memory board or cartridge.
SNMP Trap: cpqHe5ResMemBoardRemoved - 6065 in CPQHLTH.MIB
Symptom: Memory board or cartridge or riser removed. An Advanced Memory Protection sub-system

board or cartridge or riser has been removed from the system. Value 0 for CPU means memory is not
processor-based.

Server agents 88

User Action: Be sure that the board, cartridge, or riser memory is installed correctly, and then re-install
the memory board, cartridge, or processor.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeResMem2BoardSlotNum

• cpqHeResMem2BoardCpuNum

• cpqHeResMem2BoardRiserNum

Supporting SNMP Trap Description: “Memory Board or Cartridge Removed from Slot
[cpqHeResMem2BoardSlotNum], Cpu [cpqHeResMem2BoardCpuNum], Riser
[cpqHeResMem2BoardRiserNum].”

NT Event ID: 1037 (Hex) 0x4435040DL (cpqsvmsg.dll)

Log Severity: Informational (1)
Log Message: System Information Agent: Health: A memory board or cartridge has been inserted into

the system.
SNMP Trap: cpqHe5ResMemBoardInserted - 6066 in CPQHLTH.MIB
Symptom: Memory board or cartridge or riser inserted. An Advanced Memory Protection sub-system

board, cartridge, or riser has been installed. Value 0 for CPU means memory is not processor-based.
User Action: None.
SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeResMem2BoardSlotNum

• cpqHeResMem2BoardCpuNum

• cpqHeResMem2BoardRiserNum

Supporting SNMP Trap Description: “Memory Board or Cartridge Inserted into Slot
[cpqHeResMem2BoardSlotNum], Cpu[cpqHeResMem2BoardCpuNum],
Riser[cpqHeResMem2BoardRiserNum].”

NT Event ID: 1038 (Hex) 0xC435040EL (cpqsvmsg.dll)

Log Severity: Error (3)
Log Message: A memory board or cartridge bus error has been detected in the memory subsystem.
SNMP Trap: cpqHe5ResMemBoardBusError- 6067 in CPQHLTH.MIB
Symptom: Memory board, cartridge, or riser bus error detected. An Advanced Memory Protection

sub-system board, cartridge, or riser bus error has been detected. Value 0 for CPU means memory is
not processor-based.

User Action: Replace the indicated board or cartridge or Riser.
SNMP Trap Data:

• sysName,

• cpqHoTrapFlags

• cpqHeResMem2BoardSlotNum

• cpqHeResMem2BoardCpuNum

Server agents 89

• cpqHeResMem2BoardRiserNum

Supporting SNMP Trap Description: “Memory Board or Cartridge Inserted into Slot
[cpqHeResMem2BoardSlotNum], Cpu[cpqHeResMem2BoardCpuNum],
Riser[cpqHeResMem2BoardRiserNum].”

NT Event ID: 1039 (Hex) 0x8435040FL (cpqsvmsg.dll)

Log Severity: Warning (3)
Log Message: The Advanced Memory Protection sub-system has detected a memory fault. The

LockStep recovery engine has been activated. For instruction on replacing the faulty memory, see the
server documentation.

SNMP Trap: cpqHeResilientMemLockStepMemoryEngaged - 6068 in CPQHLTH.MIB
Symptom: Advanced Memory Protection LockStep Engine Memory Engaged. The Advanced Memory

Protection subsystem has detected a memory fault. The LockStep engine has been activated.
User Action: Replace the faulty memory.
Supporting SNMP Trap Data:

• sysName,

• cpqHoTrapFlags

Supporting SNMP Trap Description: “The Advanced Memory Protection subsystem has engaged the
LockStep memory.”

NT Event ID: 1072 (Hex)0x84350430 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The frequency of memory errors is high enough such that tracking of correctable

memory errors has been temporarily disabled.
SNMP Trap: cpqHe3CorrectableMemoryLogDisabled - 6016 in CPQHLTH.MIB
Symptom: Correctable memory error tracking disabled. The frequency of errors is so high that the

error tracking logic has been temporarily disabled. The cpqHeCorrMemLogStatus variable indicated
the current tracking status.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeCorrMemLogStatus

Supporting SNMP Trap Description: “Too many memory errors - tracking now disabled.”

NT Event ID: 1082 (Hex)0xc435043a (cpqsvmsg.dll)

Log Severity: Error (3)
Log Message: A Thermal Temperature Condition has been set to failed. The system will be shut down

due to this thermal condition.
SNMP Trap: cpqHe3ThermalTempFailed - 6017 in CPQHLTH.MIB
Symptom: The temperature status has been set to failed. The system is shut down due to this thermal

condition.
Supporting SNMP Trap Data:

• sysName

Server agents 90

• cpqHoTrapFlags

Supporting SNMP Trap Description: “System will be shut down due to this thermal condition.”

NT Event ID: 1083 (Hex)0x8435043b (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Thermal Temperature Condition has been set to degraded. The system may be shut

down due to this thermal condition depending on the state of the thermal degraded action value '%4'.
SNMP Trap: cpqHe3ThermalTempDegraded - 6018 in CPQHLTH.MIB
Symptom: The temperature status has been set to degraded. The server's temperature is outside of the

normal operating range. The server is shut down if the
cpqHeThermalDegradedAction variable is set to shutdown (3).

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeThermalDegradedAction

Supporting SNMP Trap Description: “Temperature out of range. Shutdown may occur.”

NT Event ID: 1084 (Hex)0x4435043c (cpqsvmsg.dll)

Log Severity: Information (1)
Log Message: The Thermal Temperature Condition has been set to OK. The server's temperature has

returned to its normal operating range.
SNMP Trap: cpqHe3ThermalTempOk - 6019 in CPQHLTH.MIB
Symptom: The temperature status has been set to OK. The server's temperature has returned to the

normal operating range.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “Temperature has returned to normal range.”

NT Event ID: 1085 (Hex)0xc435043d (cpqsvmsg.dll)

Log Severity: Error (3)
Log Message: A System Fan Condition has been set to failed. The system may be shut down due to

this thermal condition.
SNMP Trap: cpqHe3ThermalSystemFanFailed - 6020 in CPQHLTH.MIB
Symptom: The system fan status has been set to failed. A required system fan is not operating

normally. The system is shut down if the cpqHeThermalDegradedAction variable
is set to shutdown (3).

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeThermalDegradedAction

Supporting SNMP Trap Description: “Required fan not operating normally. Shutdown may occur.”

Server agents 91

NT Event ID: 1086 (Hex)0x8435043e (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: A System Fan Condition has been set to degraded. If the system fan is part of a

redundancy group, the system will not be shut down. If the system fan is not part of a redundancy
group, the system may be shut down depending on the state of the thermal degraded action value
'%4'.

SNMP Trap: cpqHe3ThermalSystemFanDegraded - 6021 in CPQHLTH.MIB
Symptom: The system fan status has been set to degraded. An optional system fan is not operating

normally.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “An optional fan is not operating normally.”

NT Event ID: 1087 (Hex)0x4435043f (cpqsvmsg.dll)

Log Severity: Information (1)
Log Message: A System Fan Condition has been set to OK. The server's system fan has resumed

normal operation.
SNMP Trap: cpqHe3ThermalSystemFanOk - 6022 in CPQHLTH.MIB
Symptom: The system fan status has been set to OK. Any previously non-operational system fans have

returned to normal operation.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “System fan has returned to normal operation.”

NT Event ID: 1088 (Hex)0xc4350440 (cpqsvmsg.dll)

Log Severity: Error (3)
Log Message: A Processor Fan Condition has been set to failed. The system will be shut down due to

this condition.
SNMP Trap: cpqHe3ThermalCpuFanFailed - 6023 in CPQHLTH.MIB
Symptom: The CPU fan status has been set to failed. A processor fan is not operating normally. The

server is shut down.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “CPU fan has failed. Server will be shutdown.”

NT Event ID: 1089 (Hex)0x44350441 (cpqsvmsg.dll)

Log Severity: Information (1)
Log Message: A Processor Fan Condition has been set to OK. The server's processor fan has resumed

normal operation.

Server agents 92

SNMP Trap: cpqHe3ThermalCpuFanOk - 6024 in CPQHLTH.MIB
Symptom: The CPU fan status has been set to OK. Any previously non-operational processor fans

have returned to normal operation.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “CPU fan is now OK.”

NT Event ID: 1090 (Hex)0x44350442 (cpqsvmsg.dll)

Log Severity: Information (1)
Log Message: The server is operational again. The server has previously been shut down by the

Automatic Server Recovery (ASR) feature and has just become operational again.
SNMP Trap: cpqHe3AsrConfirmation - 6025 in CPQHLTH.MIB
Symptom: The server is operational again. The server has previously been shut down by the

Automatic Server Recovery (ASR) feature and has just become operational again.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “Server is operational again after ASR shutdown.”

NT Event ID: 1091 (Hex)0x44350443 (cpqsvmsg.dll)

Log Severity: Information (1)
Log Message: The server is operational again. The server has previously been shut down due to a

thermal anomaly and has just become operational again.
SNMP Trap: cpqHe3ThermalConfirmation - 6026 in CPQHLTH.MIB
Symptom: The server is operational again. The server has previously been shut down due to a thermal

anomaly on the server and has just become operational again.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “Server is operational again after thermal shutdown.”

NT Event ID: 1092 (Hex)0x84350444 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: Post Errors were detected. One or more Power-On-Self-Test errors were detected during

server startup.
SNMP Trap: cpqHe3PostError - 6027 in CPQHLTH.MIB
Symptom: One or more POST errors occurred. Power On Self-Test (POST) errors occur during the

server restart process.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Server agents 93

Supporting SNMP Trap Description: “Errors occurred during server restart.”

Event Identifiers 1103-1183

NT Event ID: 1103 (Hex)0x8435044f (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Fault Tolerant Power Sub-system has been set to Degraded. Check power

connections and replace the power supply as needed.
SNMP Trap: cpqHe3FltTolPwrSupplyDegraded - 6028 in CPQHLTH.MIB
Symptom: The fault tolerant power supply sub-system condition has been set to degraded.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “The server power supply status has become degraded.”

NT Event ID: 1108 (Hex)0x84350454 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Remote Insight Board has detected unauthorized login attempts. More than '%4'

login attempts detected.
SNMP Trap: cpqSm2UnauthorizedLoginAttempts - 9003 in CPQSM2.MIB
Symptom: Remote Insight/Integrated Lights-Out Unauthorized Login Attempts. The Remote

Insight/Integrated Lights-Out firmware has detected unauthorized login attempts.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSm2CntlrBadLoginAttemptsThresh

Supporting SNMP Trap Description: “More than [cpqSm2CntlrBadLoginAttemptsThresh] unauthorized
login attempts detected.”

NT Event ID: 1109 (Hex)0xc4350455 (cpqsvmsg.dll)

Log Severity: Error (3)
Log Message: The Remote Insight Board has detected a battery failure.
SNMP Trap: cpqSm2BatteryFailed - 9004 in CPQSM2.MIB
Symptom: Remote Insight Battery Failed. The Remote Insight battery has failed and needs to be

replaced.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “Remote Insight battery failed.”

NT Event ID: 1110 (Hex)0xc4350456 (cpqsvmsg.dll)

Log Severity: Error (3)

Server agents 94

Log Message: The Remote Insight Board has detected self test error '%4'.
SNMP Trap: cpqSm2SelfTestError - 9005 in CPQSM2.MIB
Symptom: Remote Insight/Integrated Lights-Out Self Test Error. The Remote Insight/Integrated Lights-

Out firmware has detected a Remote Insight self test error.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSm2CntlrSelfTestErrors

Supporting SNMP Trap Description: “Remote Insight/Integrated Lights-Out self test error
[cpqSm2CntlrSelfTestErrors].”

NT Event ID: 1111 (Hex)0xc4350457 (cpqsvmsg.dll)

Log Severity: Error (3)
Log Message: The Remote Insight Board has detected a controller interface error.
SNMP Trap: cpqSm2InterfaceError - 9006 in CPQSM2.MIB
Symptom: Remote Insight/Integrated Lights-Out Interface Error. The host OS has detected an error in

the Remote Insight/ Integrated Lights-Out interface. The firmware is not responding.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “Server [sysName], Remote Insight/Integrated Lights-Out
interface error.”

NT Event ID: 1112 (Hex)0x84350458 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Remote Insight Board has detected that the battery is disconnected.
SNMP Trap: cpqSm2BatteryDisconnected - 9007 in CPQSM2.MIB
Symptom: Remote Insight Battery Disconnected. The Remote Insight battery cable has been

disconnected.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “Remote Insight battery disconnected.”

NT Event ID: 1113 (Hex)0x84350459 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Remote Insight Board has detected that the keyboard cable is disconnected.
SNMP Trap: cpqSm2KeyboardCableDisconnected - 9008 in CPQSM2.MIB
Symptom: Keyboard Cable Disconnected. The Remote Insight keyboard cable has been disconnected.
Supporting SNMP Trap Data:

• sysName

Server agents 95

• cpqHoTrapFlags

Supporting SNMP Trap Description: “Remote Insight keyboard cable disconnected.”

NT Event ID: 1114 (Hex)0x8435045a (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: A processor has crossed the threshold of allowable corrected errors. The processor

should be replaced.
SNMP Trap: cpqSeCpuThresholdPassed - 1001 in CPQSTDEQ.MIB
Symptom: This trap is sent when an internal processor error threshold has been passed on a particular

processor, causing it to become degraded. This trap is sent when cpqSeCpuThreshPassed transitions
from false to true.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqSeCpuSlot

• cpqSeCpuSocketNumber

Supporting SNMP Trap Description: “CPU internal corrected errors have passed a set threshold.”

NT Event ID: 1115 (Hex)0x8435045b (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: A computer cover has been removed since last system start up. Be sure the system

cover is installed properly. This situation may result in improper cooling of the system due to air flow
changes caused by the missing cover.

SNMP Trap: cpqSiHoodRemoved - 2001 in CPQSINFO.MIB
Symptom: The access panel is removed. The access panel status has been set to removed. The access

panel is not installed properly. This situation may result in improper cooling of the system due to air
flow changes caused by the missing access panel.

User Action: Replace the access panel and be sure that it is installed properly. Verify that the system is
working properly.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “Hood is removed from unit.”

NT Event ID: 1116 (Hex)0x8435045c (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Remote Insight Board has detected that the mouse cable is disconnected.
SNMP Trap: cpqSm2MouseCableDisconnected - 9009 in CPQSM2.MIB
Symptom: Mouse Cable Disconnected. The Remote Insight mouse cable has been disconnected.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Server agents 96

Supporting SNMP Trap Description: “Remote Insight mouse cable disconnected.”

NT Event ID: 1117 (Hex)0x8435045d (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Remote Insight Board has detected that the external power cable is disconnected.
SNMP Trap: cpqSm2ExternalPowerCableDisconnected - 9010 in CPQSM2.MIB
Symptom: External Power Cable Disconnected. The Remote Insight external power cable has been

disconnected.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “Remote Insight external power cable disconnected.”

NT Event ID: 1118 (Hex)0x4435045e (cpqsvmsg.dll)

Log Severity: Information (1)
Log Message: The Fault Tolerant Power Supply Sub-system has been returned to the OK state.
SNMP Trap: cpqHe4FltTolPowerSupplyOk - 6048 in CPQHLTH.MIB
Symptom: The fault tolerant power supply condition has been set back to the OK state for the

specified chassis and bay location.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolPowerSupplyChassis

• cpqHeFltTolPowerSupplyBay

• cpqHeFltTolPowerSupplyStatus

• cpqHeFltTolPowerSupplyModel

• cpqHeFltTolPowerSupplySerialNumber

• cpqHeFltTolPowerSupplyAutoRev

• cpqHeFltTolPowerSupplyFirmwareRev

• cpqHeFltTolPowerSupplySparePartNum

• cpqSiServerSystemId

Supporting SNMP Trap Description: “The Power Supply is OK on Chassis
[cpqHeFltTolPowerSupplyChassis], Bay [cpqHeFltTolPowerSupplyBay], Status
[cpqHeFltTolPowerSupplyStatus], Model [cpqHeFltTolPowerSupplyModel], Serial Num
[cpqHeFltTolPowerSupplySerialNumber], Firmware [cpqHeFltTolPowerSupplyFirmwareRev].”

NT Event ID: 1123 (Hex)0x84350463 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: Post Errors were detected. One or more Power-On-Self-Test errors were detected during

server startup.
SNMP Trap: cpqHe3PostError - 6027 in CPQHLTH.MIB
Symptom: One or more POST errors occurred. Power On Self-Test (POST) errors occur during the

server restart process.

Server agents 97

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

Supporting SNMP Trap Description: “Errors occurred during server restart.”

NT Event ID: 1124 (Hex)0x84350464 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Fault Tolerant Power Supply Sub-system is in a degraded state. Restore power or

replace the failed power supply.
SNMP Trap: cpqHe4FltTolPowerSupplyDegraded - 6049 in CPQHLTH.MIB
Symptom: The fault tolerant power supply condition has been set to degraded for the specified chassis

and bay location.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolPowerSupplyChassis

• cpqHeFltTolPowerSupplyBay

• cpqHeFltTolPowerSupplyStatus

• cpqHeFltTolPowerSupplyModel

• cpqHeFltTolPowerSupplySerialNumber

• cpqHeFltTolPowerSupplyAutoRev

• cpqHeFltTolPowerSupplyFirmwareRev

• cpqHeFltTolPowerSupplySparePartNum

• cpqSiServerSystemId

Supporting SNMP Trap Description: “The Power Supply is Degraded on Chassis
[cpqHeFltTolPowerSupplyChassis], Bay [cpqHeFltTolPowerSupplyBay], Status
[cpqHeFltTolPowerSupplyStatus], Model [cpqHeFltTolPowerSupplyModel], Serial Num
[cpqHeFltTolPowerSupplySerialNumber], Firmware [cpqHeFltTolPowerSupplyFirmwareRev].”

NT Event ID: 1125 (Hex)0xc4350465 (cpqsvmsg.dll)

Log Severity: Error (3)
Log Message: The Fault Tolerant Power Supply Sub-system is in a failed state. Restore power or

replace the failed power supply.
SNMP Trap: cpqHe4FltTolPowerSupplyFailed - 6050 in CPQHLTH.MIB
Symptom: The fault tolerant power supply condition has been set to failed for the specified chassis

and bay location.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolPowerSupplyChassis

• cpqHeFltTolPowerSupplyBay

• cpqHeFltTolPowerSupplyStatus

• cpqHeFltTolPowerSupplyModel

Server agents 98

• cpqHeFltTolPowerSupplySerialNumber

• cpqHeFltTolPowerSupplyAutoRev

• cpqHeFltTolPowerSupplyFirmwareRev

• cpqHeFltTolPowerSupplySparePartNum

• cpqSiServerSystemId

Supporting SNMP Trap Description: “The Power Supply is Failed on Chassis
[cpqHeFltTolPowerSupplyChassis], Bay [cpqHeFltTolPowerSupplyBay], Status
[cpqHeFltTolPowerSupplyStatus], Model [cpqHeFltTolPowerSupplyModel], Serial Num
[cpqHeFltTolPowerSupplySerialNumber], Firmware [cpqHeFltTolPowerSupplyFirmwareRev].”

NT Event ID: 1126 (Hex)0x84350466 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Fault Tolerant Power Supply Sub-system has lost redundancy. Restore power or

replace any failed or missing power supplies.
SNMP Trap: cpqHe3FltTolPowerRedundancyLost - 6032 in CPQHLTH.MIB
Symptom: The Fault Tolerant Power Supplies have lost redundancy for the specified chassis.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolPowerSupplyChassis

Supporting SNMP Trap Description: “The Power Supplies are no longer redundant on Chassis
[cpqHeFltTolPowerSupplyChassis].”

NT Event ID: 1127 (Hex)0x44350467 (cpqsvmsg.dll)

Log Severity: Information (1)
Log Message: Fault Tolerant Power Supply Inserted. A hot-plug fault tolerant power supply has been

inserted into the system.
SNMP Trap: cpqHe3FltTolPowerSupplyInserted - 6033 in CPQHLTH.MIB
Symptom: A Fault Tolerant Power Supply has been inserted into the specified chassis and bay

location.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolPowerSupplyChassis

• cpqHeFltTolPowerSupplyBay

Supporting SNMP Trap Description: “The Power Supply Inserted on Chassis
[cpqHeFltTolPowerSupplyChassis], Bay [cpqHeFltTolPowerSupplyBay].”

NT Event ID: 1128 (Hex)0x84350468 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: Fault Tolerant Power Supply Removed. A hot-plug fault tolerant power supply has been

removed from the system.
SNMP Trap: cpqHe3FltTolPowerSupplyRemoved - 6034 in CPQHLTH.MIB

Server agents 99

Symptom: A Fault Tolerant Power Supply has been removed from the specified chassis and bay
location.

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolPowerSupplyChassis

• cpqHeFltTolPowerSupplyBay

Supporting SNMP Trap Description: “The Power Supply Removed on Chassis
[cpqHeFltTolPowerSupplyChassis], Bay [cpqHeFltTolPowerSupplyBay].”

NT Event ID: 1129 (Hex)0x84350469 (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Fan Sub-system is in a degraded state. Replace the fan.
SNMP Trap: cpqHe3FltTolFanDegraded - 6035 in CPQHLTH.MIB
Symptom: The Fault Tolerant Fan condition has been set to degraded for the specified chassis and

fan.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolFanChassis

• cpqHeFltTolFanIndex

Supporting SNMP Trap Description: “The Fan Degraded on Chassis [cpqHeFltTolFanChassis], Fan
[cpqHeFltTolFanIndex].”

NT Event ID: 1130 (Hex)0xc435046a (cpqsvmsg.dll)

Log Severity: Error (3)
Log Message: The Fan Sub-system is in a failed state. Replace the fan.
SNMP Trap: cpqHe3FltTolFanFailed - 6036 in CPQHLTH.MIB
Symptom: The Fault Tolerant Fan condition has been set to failed for the specified chassis and fan.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolFanChassis

• cpqHeFltTolFanIndex

Supporting SNMP Trap Description: “The Fan Failed on Chassis [cpqHeFltTolFanChassis], Fan
[cpqHeFltTolFanIndex].”

NT Event ID: 1131 (Hex)0x8435046b (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: The Fan Sub-system has lost redundancy. Replace any failed or missing fans.
SNMP Trap: cpqHe3FltTolFanRedundancyLost - 6037 in CPQHLTH.MIB
Symptom: The Fault Tolerant Fans have lost redundancy for the specified chassis.

Server agents 100

Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolFanChassis

Supporting SNMP Trap Description: “The Fans are no longer redundant on Chassis
[cpqHeFltTolFanChassis].”

NT Event ID: 1132 (Hex)0x4435046c (cpqsvmsg.dll)

Log Severity: Information (1)
Log Message: Fan Inserted. A hot-plug fan has been inserted into the system.
SNMP Trap: cpqHe3FltTolFanInserted - 6038 in CPQHLTH.MIB
Symptom: A Fault Tolerant Fan has been inserted into the specified chassis and fan location.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolFanChassis

• cpqHeFltTolFanIndex

Supporting SNMP Trap Description: “The Fan Inserted on Chassis [cpqHeFltTolFanChassis], Fan
[cpqHeFltTolFanIndex].”

NT Event ID: 1133 (Hex)0x8435046d (cpqsvmsg.dll)

Log Severity: Warning (2)
Log Message: Fan Removed. A hot-plug fan has been removed from the system.
SNMP Trap: cpqHe3FltTolFanRemoved - 6039 in CPQHLTH.MIB
Symptom: A Fault Tolerant Fan has been removed from the specified chassis and fan location.
Supporting SNMP Trap Data:

• sysName

• cpqHoTrapFlags

• cpqHeFltTolFanChassis

• cpqHeFltTolFanIndex

Supporting SNMP Trap Description: “The Fan Removed on Chassis [cpqHeFltTolFanChassis], Fan
[cpqHeFltTolFanIndex].”

NT Event ID: 1134 (Hex)0xc435046e (cpqsvmsg.dll)

Log Severity: Error (3)
Log Message: A Temperature Sensor Condition has been set to failed. The system will be shut down

due to this overheat condition.
SNMP Trap: cpqHe3TemperatureFailed - 6040 in CPQHLTH.MIB
Symptom: The temperature status has been set to failed in the specified chassis and location. The

system is shut down due to this condition.
Supporting SNMP Trap Data:

• sysName