HOTPOINT OSHS89EDC 0 (K), OSHS89EDC 0 (MI) User Manual

Please phone us on

08448 24 24 24

to activate your

guarantee

OSHS89EDC 0 (K) OSHS89EDC 0 (MI) OSHS89ED 0 (MI)

English

Operating Instructions

OVEN

Contents

Operating Instructions,1 Warnings,2 Description of the appliance,3 Description of the appliance,4 Installation,5 Electrical Connection,5 Oven structure,7 Start-up and use,8 Cooking modes,9 Precautions and tips,15 Maintenance and care,15 Troubleshooting,17 After Sales Service,19 Guarantee,20

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Warnings

WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.

Keep children away from the appliance during the automatic cleaning cycle as surfaces may become very hot.

Never use steam cleaners or pressure cleaners on the appliance.

WARNING: Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric shock.

! When you place the rack inside, make sure that the stop is directed upwards and in the back of the cavity.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Description of the appliance

121110

123

Overall view

1. POSITION 1

2. POSITION 2

3. POSITION 3

4. POSITION 4

5. POSITION 5

6. DIVIDER “D” POSITION

7. POSITION 6

8. POSITION 7

9. GUIDES for the sliding racks

10. DRIPPING PAN

11. RACK shelf

12. DIVIDER shelf

13. Control panel

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Description of the appliance

121314

1718192021

123

56789

Control panel

1. SELECTOR knob

2. CONTROL PANEL POWER BUTTON

3. DISPLAY

4. THERMOSTAT / TIMER knob

5. START / STOP

6. MINUTE MINDER icon

7. TIMER icon

8. CONTROL PANEL LOCK icon

9. SELECT CAVITY icon

10. LIGHT icon

Display

11. SMALL CAVITY icon

12. CAVITY TEMPERATURE display

13. CONTROL PANEL LOCK indicator

14. TIME display

15. DURATION icon

16. END OF COOKING icon

17. CLOCK icon

18. MINUTE MINDER icon

19. CAVITY PREHEATING / RESIDUAL HEAT indicator

20. MAIN CAVITY icon

21. MODE icons

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Installation

590 mm.

595 mm.

22,5 mm.*

20,5 mm.

550 mm.

570 mm.

20 mm.

575-585 mm.

45 mm.

560 mm.

550 mm.

min.

! Please keep this instruction booklet in a safe place for future reference. If the appliance is sold, given away or moved, please make sure the booklet is

also passed on to the new owners so that they may benet from the advice

contained within it.

Centring and xing

Secure the appliance to the cabinet:

• open the oven door.

• slide out the side gaskets at the top until the 2 xing holes are exposed;

• x the oven to the cabinet using the 2 wood screws.

• reposition the 2 gaskets.

! Please read this instruction manual carefully: it contains important information concerning the safe operation, installation and maintenance of the appliance.

Positioning

! Do not let children play with the packaging material; it should be disposed of in accordance with local separated waste collection standards (see Precautions and tips).

! The appliance must be installed by a qualied professional in accordance

with the instructions provided. Incorrect installation may damage property or cause harm to people or animals.

Built-in appliances

Use an appropriate cabinet to ensure that the appliance operates properly:

• the panels adjacent to the oven must be made of heat-resistant material.

• cabinets with a veneer exterior must be assembled with glues which can

withstand temperatures of up to 100°C.

• to install the oven under the counter (see diagram) or in a kitchen unit,

the cabinet must have the following dimensions:

! All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool.

Electrical Connection

The electrical connection to the mains must be made on the appliance. The power voltage and frequency are as indicated on the rating plate.

! THIS APPLIANCE MUST BE EARTHED.

! The appliance must not come into contact with electrical parts once it has been installed. The indications for consumption given on the data plate have been calculated for this type of installation.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips

of wood, or on a completely at surface with

an opening of at least 45 x 560 mm (see diagrams).

Fitting the power supply cable

1. Open the terminal board by inserting a screwdriver into the side tabs of the cover. Use the screwdriver as a lever by pushing it down to open the cover (see diagram).

2. Install the power supply cable by loosening the cable clamp screw and the three wire contact screws

L-N- . Connect the wires to the corresponding terminals: the Blue wire to the terminal marked (N), the Brown wire to the terminal marked (L) and the Yellow/Green wire to

the terminal marked

3. Secure the cable by fastening the clamp screw.

4. Close the cover of the terminal board.

Electrical Connection:

Voltage Frequency: see data plate Fuse Section: 16A Supply cable: 3x1.5mm

(see diagram).

You can connect your oven to the system means of a terminal board. Refer to above information for the minimal cable sections and the calibration of the

min. 20 mm

FAN ASSISTED

MODE

min. 45 mm

protective elements according to the connection. If the appliance is installed with a junction box, an omnipolar circuit breaker

- with a minimum contact opening of 3mm - should be installed between the appliance and the mains.

560 mm.

45 mm.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Power cable supply connection to the electrical mains:

We recommend you use a power supply cable which is long enough to allow you to take the oven out of its recess in the event of maintenance operations

(only use HAR - H 05 - RRF quality cables tted with a plug conforming to

the regulations in force. The plug must be accessible at all times.

Unplug the appliance before all operations, even when replacing the oven lamp. Using the appliance without correct earthing is highly dangerous.

! After connecting the appliance to the exible cable, tighten all the screws

on the terminal board.

APPLIANCE SPECIFICATIONS

width 43.5 cm

Dimensions*

Volume*

Dimensions**

Volume**

height 41 cm depth 41 cm

74 l

width 45.6 cm height 41 cm

depth 41 cm

77 l

Electrical connections

Energy Label e Ecodesign

voltage: 230-240V~ 50Hz (see data plate) maximum power absorbed 2600-2800 W

Regulation (EU) No 65/2014 to supplement Directive 2010/30/EU Regulation (EU) No 66/2014 to supplement Directive 2009/125/EC Standard EN 60350-1 Standard EN 50564

Declared energy consumption for Forced convection

Class - heating mode:

This appliance conforms to the following European Economic Community directives:

- 2006/95/EC dated 12/12/06 (Low Voltage) and subsequent amendments.

- 2004/108/EC dated 03/05/89 (Electromagnetic Compatibility) and subsequent amendments.

- 93/68/EEC dated 22/07/93 and subsequent amendments.

- 2012/19/EU and subsequent amendments. 1275/2008 Stand-by/off mode

ECO

* Only for models with drawn rails. ** Only for models with wire rails.

+ 14 hidden pages