Horizon Fitness CE9.2 User Manual

CE9.2

ELLIPTICAL OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE DE L’EXERCISEUR ELLIPTIQUE

Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL. Lire le GUIDE D’UTILISATION DE L’EXERCISEUR ELLIPTIQUE avant de se servir du présent MANUEL DU PROPRIÉTAIRE.

3 ENGLISH 32 FRANÇAIS

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

Read this ELLIPTICAL GUIDE before using the OWNER’S MANUAL. When using an electrical product, basic precautions should always be followed, including the following: Read all instructions before using this elliptical. It is the responsibility of the owner to ensure that all users of this elliptical are adequately informed of all warnings and precautions. If you have any questions after reading this guide, contact Customer Tech Support at the number listed on the back panel of the OWNER’S MANUAL.

This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school or institutional setting. Failure to comply will void the warranty.

DANGER

TO REDUCE THE RISK OF ELECTRICAL SHOCK:

Always unplug the elliptical from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or taking off parts.

WARNING

• To reduce the risk of burns, fire, electrical shock or injury to persons:

• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop exercising immediately and consult your physician before continuing.

• When exercising, always maintain a comfortable pace. Do not sprint above 80 RPMs on this machine.

• To maintain balance, it is recommended to keep a grip on the handlebars while exercising, mounting or dismounting the machine.

• Do not turn pedal arms by hand.

• Make sure handlebars are secure before each use.

• Keep the topside of the foot support clean and dry.

• Care should be taken when mounting or dismounting the equipment. Before mounting or dismounting, move the pedal on the mounting or dismounting side to its lowest position and bring the machine to a complete stop.

• Do not wear clothes that might catch on any part of the elliptical.

• Always wear athletic shoes while using this equipment.

• Do not jump on the elliptical.

• At no time should more than one person be on the elliptical while in operation.

• This elliptical should not be used by persons weighing more than the specified user capacity in the OWNER’S MANUAL WARRANTY SECTION. Failure to comply will void the warranty.

• This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school or institutional setting. Failure to comply will void the warranty.

• Do not use elliptical in any location that is not temperature controlled, such as but not limited to garages, porches, pool rooms, bathrooms, car ports or outdoors. Failure to comply will void the warranty.

• To prevent electrical shock, never drop or insert any object into any opening.

• Connect this exercise product to a properly grounded outlet only.

WARNING

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.

• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.

• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

• Use the elliptical only as described in the elliptical guide and owner’s manual.

• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp cloth only; never use solvents. (See MAINTENANCE)

• The elliptical should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or taking off parts.

• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.

• At NO time should pets or children under the age of 13 be closer to the elliptical than 10 feet.

• At NO time should children under the age of 13 use the elliptical.

• Children ove

• Never operate the elliptical if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or immersed in water. Return the elliptical to a service center for examination and repair.

• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.

• To disconnect, turn all controls to the off position, then remove plug from outlet.

• Do not remove the console covers unless instructed by Customer Tech Support. Service should only be done by an authorized service technician

It is essential that your elliptical is used only indoors, in a climate controlled room. If your elliptical has been exposed to colder temperatures or high moisture climates, it is strongly recommended that the elliptical is warmed up to room temperature before first time use. Failure to do so may cause premature electronic failure.

r the age of 13 or disabled persons should not use the elliptical without adult supervision.

GROUNDING INSTRUCTIONS

If your elliptical has power incline with a 3-prong plug, you must follow these grounding instructions.

This product must be grounded. If a elliptical should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.

DANGER

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This product is for use on a nominal 110-120 Volt circuit and has a grounding plug that looks like the plug in the illustration. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.

This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit and observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one circuit. This elliptical should be used with a minimum 15-amp circuit. Note: There are usually multiple outlets on one circuit. This elliptical should be used with a minimum 15-amp circuit.

WARNING

3-POLE

GROUNDED

OUTLET

GROUNDING PIN

Connect this exercise product to a properly grounded outlet only. Never operate product with a damaged cord or plug even if it is working

properly. Never operate any product if it appears damaged, or has been immersed in water. Contact Customer Tech Support for replacement or repair.

ASSEMBLY

WARNING

There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your elliptical’s serial number located on a white barcode sticker on the front stabilizer tube and enter it in the space provided below.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:

SERIAL NUMBER:

MODEL NAME: HORIZON CE9.2 ELLIPTICAL

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

SERIAL NUMBER LOCATION

SPEAKER S

IPOD/ MP3 PLAYE R POCKET

CONSOLE FAN

UPPER HANDLEBAR

WARNING

CONSULT A PHYSICIAN PRIOR TO USING ANY EXERCISE EQUIPMENT. POSSIBILITY OF SERIOUS INJURY IF EQUIPMENT IS USED IMPROPERLY. READ INSTRUCTION MANUAL BEFORE USING. KEEP CHILDREN OFF AND AWAY FROM THIS EQUIPMENT. FOR CONSUMER USE ONLY.

AVERTISSEMENT

CONSULTER UN MÉDECIN AVANT D’UTILISER CET ÉQUIPEMENT. POSSIBILITÉ DE BLESSURES SÉRIEUSES SI L’ÉQUIPEMENT EST UTILISE DE MANIÈRE INCORRECTE. AVANT USAGE, LIRE LE GUIDE D’UTILISATEUR. NE PAS LAISSER CET ÉQUIPEMENT À LA PORTÉE DES ENFANTS. POUR USAGE DOMESTIQUE UNIQUEMENT.

PRECAUCIÓN

CONSULTAR CON UN MEDICO ANTES DE USAR ESTE EQUIPO. POSIBILIDAD DE RESULTAR EN HERIDAS GRAVES SI EL EQUIPO ESTÁ UTILIZADO IMPROPIAMENTE. LEER LA GUÍA DE INSTRUCCIONES ANTES DE USAR.MANTENER NIÑOS PEQUEÑOS ALEJADOS DE LA MÁQUINA.ESTE EQUIPO ES SÓLO PARA EL USO DEL CONSUMIDOR.

PUL SE GRIPS

WATER BOTTLE HOLD ER

TOP CAP

PEDAL ARM

PIVOTING FOOT PAD S

GUIDE RAIL SET

REAR COVER

CAUTION ATTENTION PRECAUCIÓN

KEEP HANDS AND FEET AWAY FROM THIS AREA.

GARDER LES MAINS ET LES

PIEDS LOIN DE CETTE REGION.

MANTENGA LAS MANOS Y LOS

PIES LEJOS DE ESTA AREA.

CONSOLE

TOUCH PAD PANE L

AND DISPLAY W INDOWS

CONSOLE M AST

LOWER HANDLEBAR

POWER CORD SOCKET

STAB ILIZE R TUBE

CRANK

MAIN FRAME

LOWER LINK ARM

TOOLS INCLUDED:

F Screwdriver F 8 mm L-Wrench F 13/15 mm Flat Wrench F 5 mm L-Wrench/Screwdriver F 5 mm L-Wrench

PRE ASSEMBLY

UNPACKING

Unpack the product where you will be using it. Place the elliptical carton on a level flat surface. It is recommended that you place a protective covering on your floor. Never open box when it is on its side.

PARTS INCLUDED:

F 1 Stabilizer Tube F 1 Guide Rail Set F 2 Pedal Arms F 2 Lower Handlebars F 2 Upper Handlebars F 2 Lower Link Arms With Footpads F 1 Top Cap (2 pieces) F 1 Console Mast F 1 Console Mast Boot F 1 Console F 2 Handlebar Caps F 1 Water Bottle Holder F 1 Rear Cover F 1 Audio Adapter Cable F 1 Power Cord F 1 Hardware Kit

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.

NEED HELP?

If you have questions or if

there are any missing parts,

contact Customer Tech

Support. Contact information

is located on the back panel

of this manual.

ASSEMBLY STEP 1

HARDWARE BAG 1 CONTENTS :

STABILIZER TU BE

ARC WASHER S (C)

SPRIN G WASHER S (B)

BOLTS (A)

MAIN FRAME

BOLT (A) 30 mm Qty: 4

SPRIN G WASHER (B) 15 mm Qty: 4

ARC WASHER (C) 17 mm Qty: 4

A Open HARDWARE BAG 1.

B Attach the STABILIZER TUBE to the MAIN

FRAME using 2 BOLTS (A), 2 SPRING WASHERS (B) and 2 ARC WASHERS (C) on

each side.

ASSEMBLY STEP 2

FLAT WASHER (D) 20 mm Qty: 4

NUTS (J)

SPRIN G WASHER S (I)

FLAT WASHERS (H)

HARDWARE BAG 2 CONTENTS

SPRING WASH ER (E) 18 mm Qty: 4

FLAT WASHER (H) 16 mm Qty: 4

BOLTS (F)

SPRIN G WASHER S (E)

FLAT WASHERS (D)

INCLIN E BRACKET

SPRING WASH ER (I) 15 mm Qty: 4

BOLT (F) 20 mm Qty: 4

BOLT (G) 35 mm Qty: 4

NUT (J) Qty: 4

MAIN FRAME

BOLTS (G)

GUID E RAIL SET

A Open HARDWARE BAG 2.

B Attach the GUIDE RAIL SET to the

MAIN FRAME using 4 BOLTS (F), 4 SPRING WASHERS (E) and 4 FLAT WASHERS (D).

C Attach the GUIDE RAIL SET to the

INCLINE BRACKET using 4 BOLTS (G), 4 FLAT WASHERS (H), 4 SPRING WASHERS (I) and 4 NUTS (J).

ASSEMBLY STEP 3

HARDWARE BAG 3 CONTENTS :

NOTE: Be careful not to pinch any wires while attaching the console mast.

CONSOLE MAST

CONSOLE CABLE

PRE-INSTALLED BOLTS

MAIN FRAME

GUID E RAIL

PEDAL ARM WHEE L

CRANK

PEDAL ARM

WAVY WASHER (L)

FLAT WASHER (K)

SPRING WASH ER (B)

BOLT (M)

WAVY WASHER (L)

22.5 mm Qty: 2

BOLT (M) 20 mm Qty: 2

SPRING WASHE R (B) 15 mm Qty: 2

FLAT WASHER (K) 20 mm Qty: 2

A Open HARDWARE BAG 3.

B Carefully pull the CONSOLE CABLE through

the CONSOLE MAST using the twist tie located inside the CONSOLE MAST.

C Gently slide the CONSOLE MAST onto the

MAIN FRAME and attach CONSOLE MAST to MAIN FRAME using PRE-INSTALLED BOLTS.

D Slide WAVY WASHER (L) over CRANK

followed by PEDAL ARM as shown. Rest PEDAL ARM WHEEL on GUIDE RAIL.

E Attach the PEDAL ARM to the CRANK using 1

FLAT WASHER (K), 1 SPRING WASHER (B) and 1 BOLT (M).

F Repeat steps D–E on the opposite side of the

elliptical.

ASSEMBLY STEP 4

HARDWARE BAG 4 CONTENTS :

BOLT (P)

SPRING WASH ER (Q)

FLAT WASHER (R)

PEDAL ARM BRACKET

FLAT WASHERS (N)

WAVY WASHER (O)

LOWER LINK ARM

FLAT WASHER (N) 27 mm Qty: 4

SPRIN G WASHER (Q)

15.4 mm Qty: 2

WAVY WASHER (O) 29 mm Qty: 2

FLAT WASHER (R) 20 mm Qty: 2

BOLT (P) 20 mm Qty: 2

A Open HARDWARE BAG 4.

B Slide 1 FLAT WASHER (N), 1 WAVY

WASHER (O) and another FLAT WASHER (N) onto the LOWER LINK ARM.

C Slide the LOWER LINK ARM into the

PEDAL ARM BRACKET.

D Attach the LOWER LINK ARM to the

PEDAL ARM BRACKET using 1 FLAT WASHER (R), 1 SPRING WASHER (Q)

and 1 BOLT (P).

E Repeat steps B–D on the opposite side of

the elliptical.

ASSEMBLY STEP 5

HARDWARE BAG 5 CONTENTS :

RUBB ER WASHER (S) 26 mm Qty: 2

CONSOLE MAST

LOWER HANDLEBAR

FLAT WASHER (T) 25 mm Qty: 4

RUBB ER WASHER (S)

FLAT WASHERS (T)

FLAT WASHERS (H)

HANDLEBAR

CAP

BOLT (U)

SPRIN G

WASHER (B)

FLAT WASHER (H) 20 mm Qty: 4

SPRIN G WASHER (B) 15 mm Qty: 2

BOLT (U) 20 mm Qty: 2

A Open HARDWARE BAG 5.

B Slide 1 RUBBER WASHER (S) and 1 FLAT

WASHER (T) onto the CONSOLE MAST.

C Slide LOWER HANDLEBAR onto CONSOLE

MAST and attach using 1 FLAT WASHER (T), 1 FLAT WASHER (H), 1 HANDLEBAR CAP, 1 FLAT WASHER (H), 1 SPRING WASHER (B) and 1 BOLT (U).

D Repeat steps B–C on the opposite side of the

elliptical.

ASSEMBLY STEP 6

HARDWARE BAG 6 CONTENTS :

LOWER LINK ARM

TEFLON WASHER S (V)

NUT (Y)

LOWER HANDLEBAR

FLAT WASHE R (W)

SPRING WASHER (B)

BOLT (X)

TEFLON WASHER (V)

28.4 mm Qty: 4

FLAT WASHER (W) 17 mm Qty: 2

SPRING WASH ER (B) 15 mm Qty: 2

BOLT (X) 70 mm Qty: 2

NUT (Y) Qty: 2

A Open HARDWARE BAG 6.

B Align end of LOWER LINK ARM with bracket on

bottom of LOWER HANDLEBAR.

C Place TEFLON WASHERS (V) on both sides of

the LOWER LINK ARM. While holding TEFLON WASHERS (V) slide LOWER LINK ARM into bottom end of LOWER HANDLEBAR.

D Secure the joint with 1 FLAT WASHER (W), 1

SPRING WASHER (B),1 BOLT (X) and secure with 1 NUT (Y).

E Repeat steps B–D on the opposite side of the

elliptical.

ASSEMBLY STEP 7

WATER BOTTLE HOLDER

CONSOLE MAST BOOT

TOP CAP (LEFT & RIG HT)

SCREWS (Z)

REAR CAP

SCREWS (Z)

CONSOLE MAST

SCREWS (AA)

HARDWARE BAG 7 CONTENTS :

SCREW (Z) 15 mm Qty: 5

SCREW (AA) 20 mm Qty: 2

A Open HARDWARE BAG 7.

B Slide RIGHT AND LEFT TOP CAP over

CONSOLE MAST and attach using 3 SCREWS (Z).

C Slide CONSOLE MAST BOOT around

CONSOLE MAST and insert into TOP CAP.

D Slide WATER BOTTLE HOLDER over

CONSOLE MAST and attach using 2 SCREWS (AA).

E Slide REAR CAP over REAR STABILIZER

and attach using 2 SCREWS (Z).

REAR STABILIZE R

ASSEMBLY STEP 8

CONSOLE

CONSOLE CABLES

HARDWARE BAG 8 CONTENTS :

BOLT (BB) 12 mm Qty: 4

CONSOLE MAST

UPPER HAND LEBAR

BOLTS (BB)

PRE-INSTALLED

SET SCREWS

LOWER HANDLEBAR

NOTE: Be careful not to pinch any wires while attaching the console or handlebars.

A Open HARDWARE BAG 8.

B Attach the CONSOLE CABLES to the CONSOLE.

C Carefully tuck the CONSOLE CABLES into the

CONSOLE MAST before attaching the CONSOLE. Attach CONSOLE to CONSOLE MAST using 4 BOLTS (BB).

D Slide UPPER HANDLEBAR onto LOWER

HANDLEBAR making sure handlebars are joined together completely. Secure UPPER HANDLEBAR to LOWER HANDLEBAR using PRE-ATTACHED SET SCREWS.

Make sure upper handlebars are as far down as possible. Handlebars can be damaged If not secured correctly.

E Repeat step D on other side.

YOU ARE FINISHED!

ELLIPTICAL OPERATION

This section explains how to use your elliptical’s console and programming. The BASIC OPERATION section in the ELLIPTICAL GUIDE has instructions for the following:

• LOCATION OF THE ELLIPTICAL

• POWER/GROUNDING INSTRUCTIONS

• FOOT POSITIONING

• MOVING THE ELLIPTICAL

• LEVELING THE ELLIPTICAL

• POWER/MANUAL INCLINE OPERATION

• USING THE HEART RATE FUNCTION

MANUAL WEIGHT

LOSS

MUSCLE

TONER

STRENGTH BUILDER

CONSTANT

WATTS

CABOT

TRAIL

BANFF ASCENT

BANFF

DESCENT

MAX

CARDIO

CUSTOM 1 CUSTOM 2

STAGE 1 STAGE 2 STAGE 3 STAGE 4 STAGE 5 STAGE 6 STAGE 7 STAGE 8 STAGE 9 STAGE 10 STAGE 11

N NQ

L K

100

IN CL IN E Q UI CK K EY S LE VE L QU I CK K EY S

F I T N E S S J O U R N A L S Y S T E M

DISTANCE CALORIES

LEVEL

PERSONAL

BEST

TIME

LAST 5

WORKOUTS

WORKOUT

STATS

HOLD TO RESET

WORKOUT

TOTALS

PACE ELEVATION GAIN INCLINE

(FEET)

CE9.2

D EJ

+ 44 hidden pages