Horizon Fitness CE8.8 Owner's Manual
CE8.8
ELLIPTICAL OWNER’S MANUAL
MANUEL DU PROPRIÉTAIRE DE L’EXERCISEUR ELLIPTIQUE
MANUAL DEL PROPIETARIO DE LA MÁQUINA ELÍPTICA
Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL.
Lire le GUIDE D’UTILISATION DE L’EXERCISEUR ELLIPTIQUE avant de se servir du présent MANUEL DU PROPRIÉTAIRE.
Lea la GUÍA DE LA MÁQUINA ELÍPTICA antes de usar este MANUAL DEL PROPIETARIO.
HZ14_OM_NA_CE8.8_Rev1_2.indd 1 6/4/14 8:59 AM
2 ENGLISH
30 FRANÇAIS
58 ESPAÑOL
IMPORTANT PRECAUTIONS
SAVE THESE INSTRUCTIONS
Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL. When using an electrical product, basic precautions
should always be followed, including the following: Read all instructions before using this elliptical. It is the responsibility of
the owner to ensure that all users of this elliptical are adequately informed of all warnings and precautions. If you have any
questions after reading this guide, contact Customer Tech Support at the number listed on the back panel.
This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school or institutional
setting. Failure to comply will void the warranty.
32
HZ14_OM_NA_CE8.8_Rev1_2.indd 2-3 6/4/14 8:59 AM
DANGER
WARNING
TO REDUCE THE RISK OF ELECTRICAL SHOCK:
Always unplug the elliptical from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or
taking off parts.
WARNING
• To reduce the risk of burns, fire, electrical shock or injury to persons:
• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop
exercising immediately and consult your physician before continuing.
• When exercising, always maintain a comfortable pace. Do not sprint above 80 RPMs on this machine.
• To maintain balance, it is recommended to keep a grip on the handlebars while exercising, mounting or dismounting
the machine.
• Do not turn pedal arms by hand.
• Make sure handlebars are secure before each use.
• Keep the topside of the foot support clean and dry.
• Care should be taken when mounting or dismounting the equipment. Before mounting or dismounting, move the pedal on
the mounting or dismounting side to its lowest position and bring the machine to a complete stop.
• Do not wear clothes that might catch on any part of the elliptical.
• Always wear athletic shoes while using this equipment.
• Do not jump on the elliptical.
• At no time should more than one person be on the elliptical while in operation.
• This elliptical should not be used by persons weighing more than the specified user capacity in the OWNER’S MANUAL
WARRANTY SECTION. Failure to comply will void the warranty.
• This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school or institutional
setting. Failure to comply will void the warranty.
• Do not use elliptical in any location that is not temperature controlled, such as but not limited to garages, porches, pool
rooms, bathrooms, car ports or outdoors. Failure to comply will void the warranty.
• To prevent electrical shock, never drop or insert any object into any opening.
• Connect this exercise product to a properly grounded outlet only.
TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:
• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.
• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.
• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.
• Use the elliptical only as described in the elliptical guide and owner’s manual.
• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp
cloth only; never use solvents. (See MAINTENANCE)
• The elliptical should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or
taking off parts.
• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
• At NO time should children under the age of 13 or pets be within 10 feet of the machine.
• At NO time should children under the age of 13 use the elliptical.
• Children over the age of 13 or disabled persons should not use the elliptical without adult supervision.
• Never operate the elliptical if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged,
or immersed in water. Contact tech support at the number on the back panel to schedule service.
• To disconnect, turn all controls to the off position, then remove plug from outlet.
• Do not remove the console covers unless instructed by Customer Tech Support. Service should only be done by an
authorized service technician
It is essential that your elliptical is used only indoors, in a climate controlled room. If your elliptical has been exposed
to colder temperatures or high moisture climates, it is strongly recommended that the elliptical is warmed up to room
temperature before first time use. Failure to do so may cause premature electronic failure.
WARNING
This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
54
HZ14_OM_NA_CE8.8_Rev1_2.indd 4-5 6/4/14 8:59 AM
ASSEMBLY
WARNING
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To
prevent damage to the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your elliptical’s serial number located on a white barcode
sticker on the front stabilizer tube and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:
SERIAL NUMBER:
SERIAL NUMBER LOCATION
EP
MODEL NAME: HORIZON CE8.8 ELLIPTICAL
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
76
HZ14_OM_NA_CE8.8_Rev1_2.indd 6-7 6/4/14 8:59 AM
CONSOLE FAN
SPEAKERS
UPPER HANDLEBAR
WATER BOTTLE HOLDER
TOP CAP
MANUAL INCLINE LEVER
PEDAL ARM
PIVOTING FOOT PADS
GUIDE RAIL SET
REAR COVER
MUSIC PLAYER / READING RACK
CONSOLE
PULSE GRIPS
CONSOLE MAST
LOWER HANDLEBAR
CRANK
POWER CORD SOCKET
STABILIZER TUBE
MAIN FRAME
LOWER LINK ARM
TOOLS REQUIRED:
F L-Wrench
F Flat Wrench
F L-Wrench/Screwdriver
F Screwdriver (not included)
PARTS INCLUDED:
F 1 Main Frame
F 1 Stabilizer Tube
F 1 Guide Rail Set
F 1 Manual Incline Lever
F 1 Console Mast
F 2 Pedal Arms
F 2 Lower Handlebars
F 2 Upper Handlebars
F 2 Handlebar Caps
F 2 Lower Link Arms With Footpads
F 1 Front Top Cap Piece
F 1 Rear Top Cap Piece
F 1 Console Mast Boot
F 1 Console
F 1 Rear Cover
F 1 Audio Adapter Cable
F 1 Power Cord
F 1 Hardware Kit
PRE ASSEMBLY
UNPACKING
Unpack the product where you will be using it. Place the elliptical carton on a level
flat surface. It is recommended that you place a protective covering on your floor.
Never open box when it is on its side.
NOTE: It is recommended that two people work together for ease and efficiency
while assembling an elliptical.
IMPORTANT NOTES
During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded. It is recommended you complete the full assembly of your
unit before completely tightening any ONE bolt. Several parts have been prelubricated to aid in assembly and usage. Please do not wipe this off. If you
have difficulty, a light application of lithium bike grease is recommended.
NEED HELP?
If you have questions or if there are any missing parts, contact Customer Tech
Support. Contact information is located on the back panel of this manual.
98
HZ14_OM_NA_CE8.8_Rev1_2.indd 8-9 6/4/14 8:59 AM
ASSEMBLY STEP 1
A
BC2
1
3
4
EBF
D
ASSEMBLY STEP 2
HARDWARE FOR STEP 1
PART TYPE QTY
A BUTTON HEAD BOLT 4
B SPRING WASHER 4
C ARC WASHER 4
A Open HARDWARE FOR STEP 1.
B Attach the STABILIZER TUBE (1) to the
MAIN FRAME (2) using 2 BOLTS (A),
2 SPRING WASHERS (B) and 2 ARC
WASHERS (C) on each side.
HARDWARE FOR STEP 2
PART TYPE QTY
D BUTTON HEAD BOLT 4
E FL AT WASHER 4
B SPRING WASHER 4
F NUT 4
A Open HARDWARE FOR STEP 2.
B Attach MANUAL INCLINE LIFT LEVER
(3) to GUIDE RAIL SET (4) using 4 BOLTS
(D), 4 FLAT WASHERS (E), 4 SPRING
WASHERS (B) and 4 NUTS (F).
1110
HZ14_OM_NA_CE8.8_Rev1_2.indd 10-11 6/4/14 8:59 AM
ASSEMBLY STEP 3
432
HIG
2
7
5
9
K
L
B
86J
ASSEMBLY STEP 4
HARDWARE FOR STEP 3
PART TYPE QTY
G SOCKET CAP BOLT 4
H SPRING WASHER 4
I FLAT WASHE R 4
A Open HARDWARE FOR STEP 3.
B Align GUIDE RAIL SET (4) with MAIN
FRAME (2) as shown.
C Lift up on the MANUAL INCLINE LIFT
LEVER (3) and place it in one of the holes
inside the MAIN FRAME (2).
D Attach the GUIDE RAIL SET (4) to the
MAIN FRAME (2) using 4 BOLTS (G),
4 SPRING WASHERS (H) and 4 FLAT
WASHERS (I).
NOTE: Be
careful not
to pinch any
wires while
attaching the
console mast.
HARDWARE FOR STEP 4
PART TYPE QTY
J WAVY WASHER 2
K FL AT WASHER 2
B SPRING WASHER 2
L BUTTON HEAD BOLT 2
A Open HARDWARE FOR STEP 4.
B Carefully pull the CONSOLE CABLE (5)
through the CONSOLE MAST (6) using
the twist tie located inside the CONSOLE
MAST (6).
C Attach CONSOLE MAST (6) to MAIN
FRAME (2) using PRE-INSTALLED
BOLTS AND WASHERS (7).
D Slide WAVY WASHER (J) over CRANK
(8) followed by PEDAL ARM (9) as shown.
Rest pedal arm wheel on guide rail.
E Attach the PEDAL ARM (9) to the CRANK
(8) using 1 FLAT WASHER (K), 1 SPRING
WASHER (B) and 1 BOLT (L).
F Repeat steps D–E on the opposite side of
the elliptical.
1312
HZ14_OM_NA_CE8.8_Rev1_2.indd 12-13 6/4/14 8:59 AM
ASSEMBLY STEP 5
1011MNM
KBL
O
M
P
B
6
12
13
L
ASSEMBLY STEP 6
HARDWARE FOR STEP 5
PART TYPE QTY
M F L AT WAS HER 4
N WAVY WASHER 2
K FL AT WASHER 2
B SPRING WASHER 2
L BUTTON HEAD BOLT 2
A Open HARDWARE FOR STEP 5.
B Slide 1 FLAT WASHER (M), 1 WAVY
WASHER (N) and another FLAT
WASHER (M) onto the LOWER LINK
ARM (10).
C Slide the LOWER LINK ARM (10) into the
PEDAL ARM BRACKET (11).
D Attach the LOWER LINK ARM (10)
to the PEDAL ARM BRACKET (11)
using 1 FLAT WASHER (K), 1 SPRING
WASHER (B) and 1 BOLT (L).
E Repeat steps B–D on the opposite side of
the elliptical.
HARDWARE FOR STEP 6
PART TYPE QTY
O RUBBER WASHER 2
M F L AT WAS HER 2
P FL AT WASHER 4
B SPRING WASHER 2
L BUTTON HEAD BOLT 2
A Open HARDWARE FOR STEP 6.
B Slide 1 RUBBER WASHER (O) and 1 FLAT
WASHER (M) onto the CONSOLE MAST (6).
C Slide LOWER HANDLEBAR (12) onto
CONSOLE MAST (6) and attach using 1 FLAT
WASHER (P), 1 HANDLEBAR CAP (13),
1 FLAT WASHER (P), 1 SPRING WASHER (B)
and 1 BOLT (L).
D Repeat steps B–C on the other side.
1514
HZ14_OM_NA_CE8.8_Rev1_2.indd 14-15 6/4/14 8:59 AM
ASSEMBLY STEP 7
10
K
B
12
Q
F
14
R
16
6
15
4
17
ASSEMBLY STEP 8
HARDWARE FOR STEP 7
PART TYPE QTY
Q BO LT 2
B SPRING WASHER 2
K FL AT WASHER 2
F NUT 2
A Open HARDWARE BAG 7.
B Slide LOWER LINK ARM (12) into bottom end
of LOWER HANDLEBAR (10).
C Secure the joint with 1 BOLT (Q), 1 SPRING
WASHER (B),1 FLAT WASHER (K) and 1
NUT (F).
D Repeat steps B–C on the opposite side of
the elliptical.
HARDWARE FOR STEP 8
PART TYPE QTY
R SCREW 3
A Open HARDWARE BAG 8.
B Slide FRONT TOP CAP PIECE (14)
and REAR TOP CAP TPIECE (15) over
CONSOLE MAST (6) and snap into place.
C Insert CONSOLE MAST BOOT (16) over
TOP CAP (14) and snap into place.
D Slide REAR CAP (17) over GUIDE RAIL
(4) and attach using 3 SCREWS (R).
1716
HZ14_OM_NA_CE8.8_Rev1_2.indd 16-17 6/4/14 8:59 AM
ASSEMBLY STEP 9
18
6
19
5
21
22
12
NOTE: All hardware for this step is pre-installed.
A Remove 4 PRE-INSTALLED BOLTS (18) from the
CONSOLE (19).
B Attach the CONSOLE CABLES (5) to the
CONSOLE (19).
C Carefully tuck the CONSOLE CABLES (5) into the
CONSOLE MAST (6) before attaching the CONSOLE.
Attach CONSOLE (19) to CONSOLE MAST (6) using
4 PRE-INSTALLED BOLTS (18).
NOTE: Do not to pinch any wires while attaching the console.
ELLIPTICAL OPERATION
This section explains how to use your elliptical’s console and programming.
The BASIC OPERATION section in the ELLIPTICAL GUIDE has instructions for the following:
• LOCATION OF THE ELLIPTICAL
• POWER/GROUNDING INSTRUCTIONS
• FOOT POSITIONING
• MOVING THE ELLIPTICAL
• LEVELING THE ELLIPTICAL
D Slide the UPPER HANDLEBAR (21) onto the LOWER
HANDLEBAR (12) making sure handlebars are joined
together completely. Secure the UPPER HANDLEBAR
(21) to the LOWER HANDLEBAR (12) using PREATTACHED SET SCREWS (22).
NOTE: Make sure upper handlebars are as far down as
possible. Handlebars can be damaged If not secured correctly.
E Repeat STEP D on other side.
• POWER/MANUAL INCLINE OPERATION
• USING THE HEART RATE FUNCTION
ASSEMBLY COMPLETE!
1918
HZ14_OM_NA_CE8.8_Rev1_2.indd 18-19 6/4/14 8:59 AM
I I
A
B
J
F E
K
H
M
D
C
J
L
G
ON
CONSOLE OPERATION
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) LCD DISPLAY WINDOW: time, distance, calories, watts, RPM, incline, speed, resistance level, heart rate, fan
B) PROGRAMMING KEYS: Used to cycle through programs and user set up
C) ENTER / CHANGE DISPLAY: used to confirm selection or change display feedback during workout.
D) ENERGY SAVER LIGHT: indicates if machine is in Energy Saver mode.
E) PROGRAM KEYS: press to select workout.
F) AUDIO IN JACK: plug your media player into the console using the included audio adaptor cable.
G) VOLUME: used to adjust volume up or down.
H) FAN KEY: personal workout fan.
I) QUICK KEYS: used to reach desired resistance quickly.
J) LEVEL KEYS: used to adjust resistance level.
K) GO / PAUSE: used to start workout, pause workout, and restart after pause.
L) STOP / HOLD TO RESET: used to stop machine and also will reset machine when held down.
M) READING RACK: holds reading material.
N) FAN: personal workout fan
O) SPEAKERS: plays music through speakers when connected to your media player
2120
HZ14_OM_NA_CE8.8_Rev1_2.indd 20-21 6/4/14 8:59 AM
*MANUAL INCLINE OPERATION
The CE8.8 has an adjustable incline feature to
add variety to your workouts. To adjust the incline
up or down, stand on the side of the elliptical
and place your hand firmly on the top of the
shroud. With your other hand, grab the MANUAL
INCLINE LIFT LEVER handle, pulling back and
guiding it up or down. Ensure the pin is engaged
in the slot at the preferred incline level.
For program setup, input the incline level (0, 25,
50, 75, or 100) in when prompted.
GETTING STARTED
1) Check to make sure no objects are nearby that will hinder the
movement of the elliptical.
2) Plug in the power cord to power the elliptical ON.
3) Select User 1, User 2, or Guest using and press ENTER.
4) Set User Weight using and press ENTER.
5) You have the following options to start your workout:
FINISHING YOUR WORKOUT
When your workout is complete, the console
will display “workout complete” and beep. Your
workout information will stay displayed on the
console for 30 seconds and then reset.
DISPLAY WINDOW
• TIME: Shown as minutes : seconds. View the time remaining or the time elapsed in your workout.
• DISTANCE: Shown as miles. Indicates distance traveled or distance remaining during your workout.
• CALORIES: Total calories burned or remaining for your workout.
• RPM: Rotations Per Minute
• WATTS: Displays current user power output
• SPEED: Shown as MPH. Indicates how fast the foot pads is moving.
• INCLINE: Shown as percent. Is only lit up at 0, 25, 50, 75 and 100 for setting up programs.*
• LEVEL: Shows the current level of resistance
• HEART RATE: Shown as BPM (beats per minute). Used to monitor your heart rate (displayed when
contact is made with both pulse grips).
• FAN: Indicates fan setting (low, medium, high).
• TRACK: Follows progress around a simulated track. Segments light up with every 12.5 meters
completed. One lap around the track is 400 meters (approximately 1/4 mile).
A) QUICK START UP
Simply press GO to begin working out.
Time, distance and calories will all count up from zero.
The resistance level will default to level 1.
B) SELECT A PROGRAM
1) Press desired PROGRAM BUTTON to select workout and
press ENTER.
2) Set goal level using and press ENTER.
3) Set resistance using and press ENTER.
4) Set incline using and press ENTER.
(See previous page for manual incline operation)
5) Press GO to begin workout.
NOTE: You can adjust the resistance level during your workout.
TO RESET THE CONSOLE
Hold STOP key for 3 seconds.
TO CLEAR CURRENT SELECTION
To clear the current program selection or screen,
hold the stop button for 3 seconds.
2322
HZ14_OM_NA_CE8.8_Rev1_2.indd 22-23 6/4/14 8:59 AM
PROGRAM INFORMATION
MANUAL: Adjust your resistance level manually during your workout.
USING YOUR MEDIA PLAYER
1) Connect the included AUDIO ADAPTOR CABLE to the AUDIO IN JACK on the left of the console and the
headphone jack on your media player.
2) Use your media player buttons to adjust song settings.
STEPS: Promotes healthy activity with 10 step-based workouts calculated counting revolutions as a step.
Choose from 1000, 2000, 3000, 4000, 5000, 6000, 7000, 8000, 9000, and 10,000 step workouts. User sets
starting resistance and inputs the incline level that the manual incline lever is set to (0, 25, 50, 75, or 100).
CALORIES: Set goals for burning calories with six workouts. Choose from 100, 200, 300, 400, 500, and 600
calorie burn workouts. User sets starting resistance and inputs the incline level that the manual incline lever is
set to (0, 25, 50, 75, or 100). Calories burned are calculated using weight input by user with the resistance and
incline of workout.
DISTANCE: Push yourself and go further during your workout with 10 distance workouts. Choose from 1 mile, 2
miles, 5k, 5 miles, 10k, 8 miles, 15k, 10 miles, 20k, and half marathon goals. User sets starting resistance and
inputs the incline level that the manual incline lever is set to (0, 25, 50, 75, or 100).
CLIMB: Ascend world landmarks with six workouts based on vertical distance. User sets starting resistance and
inputs the incline level that the manual incline lever is set to (0, 25, 50, 75, or 100).
• Hollywood Sign – 1708 ft vertical distance
• Empire State Building – 1250 ft vertical distance
• Gateway Arch – 630 ft vertical distance
• Space Needle – 605 ft vertical distance
• Diamond Head Crater – 570 ft vertical distance
• Washington Monument – 555 ft vertical distance
3) Remove the AUDIO ADAPTOR CABLE when not in use.
ENERGY SAVER (STANDBY MODE)
This machine has a special feature called Energy Saver™ mode. This mode is NOT automatically activated.
When Energy Saver mode is activated, the display will automatically enter standby mode (Energy Saver mode) after
15 minutes of inactivity. This feature saves energy by disabling most power to the machine until a key is pressed on
the console. This feature can be turned on or off in the engineering menu.
To enter the engineering menu, press and hold the LEVEL key and LEVEL key for 3-5 seconds. Use the
keys and ENTER key to navigate to P5 under ENG2. Press ENTER to select Energy Saver mode, use keys to
select ENRGY SVE ON or OFF. Press and hold STOP for 3-5 seconds to exit ENG2. Press and hold STOP again for
3-5 seconds to exit the engineering menu.
2524
HZ14_OM_NA_CE8.8_Rev1_2.indd 24-25 6/4/14 8:59 AM
LIMITED HOME-USE WARRANTY
2726
HZ14_OM_NA_CE8.8_Rev1_2.indd 26-27 6/4/14 8:59 AM
Loading...