Horizon Fitness AFG T6, AFG T4 User Manual

ELITE SERIES

AFG

TREADMILL U S E R ’ S GUIDE

FOR MODELS :

T4_T6_Rev.1.7.indd 1 10/19/06 9:21:47 AM

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

CONGRATULATIONS and THANK YOU for your purchase of this Elite Series AFG treadmill!

Whether your goal is to win races or simply enjoy a fuller, healthier lifestyle, an Elite Series treadmill can help you attain it – adding club-quality performance to your at-home workouts, with the ergonomics and innovative features you need to get stronger and healthier, faster. Because we're committed to designing fitness equipment from the inside out, we use only the highest quality components. It's a commitment we back with one of the strongest frame-to-motor warranty packages in the industry.

You want exercise equipment that offers the most comfort, the best reliability and the highest quality in its class.

The Elite Series AFG delivers.

IN TRODUCTION

Important Precautions

Assembly

Before You Begin

Treadmill Operation

Conditioning Guidelines

Troubleshooting & Maintenance

Limited Warranty

CONTACT INFORMATION

Back Panel

TA B L E OF CO N T E NT S

T4_T6_Rev.1.7.indd 2-3 10/19/06 9:21:48 AM

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

This product is for use on a nominal 110-volt circuit and has a grounding plug that looks like the illustration to the right. This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit and observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one circuit. It is recommended that the treadmill be used with a 20 amp circuit for optimal performance.

IM PORTA NT SA FE TY IN STRUCTIONS

WARNING

3- Pole Grounded Out let

GROUNDED TREADMILL POWER CORD

OPERATION

To reduce the risk of damaging important components on your treadmill, it is strongly recommended that your treadmill is plugged into a dedicated 20 amp circuit, without the use of an additional extension cord and/or power strip. Failure to comply may void the warranty.

IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets.

It is essential that your treadmill is used only indoors, in a climate controlled room. If your treadmill has been exposed to colder temperatures or high moisture climates, it is strongly recommended that the treadmill is warmed up to room temperature before first time use. Failure to do so may cause premature electronic failure.

SAVE THESE INSTRUCTIONS

Read all instructions before using this treadmill. When using an electrical product, basic precautions should always be followed, including the following: Read all instructions before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions. If you have any questions after reading this manual, contact Sears at the number listed on the back cover of this manual.

Connect this exercise product to a properly grounded outlet only. See grounding instructions.

GROUNDING INSTRUCTIONS

This product must be grounded. If a treadmill should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

WARNING

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INjURY TO PERSONS:

WARNING

Never use the treadmill before securing the safety tether clip to your clothing.

If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop exercising immediately and consult your physician before continuing.

Do not wear clothes that might catch on any part of the treadmill.

Always wear athletic shoes while using this equipment.

Do not jump on the treadmill. Unplug treadmill before moving or cleaning

it. To clean, wipe surfaces down with soap and slightly damp cloth only; never use solvents. (See MAINTENANCE)

At no time should more than one person be on treadmill while in operation.

The treadmill should not be used by persons weighing more than 350 (T4) / 400 (T6) pounds. Failure to comply will void the warranty.

The treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting. Failure to comply will void the warranty.

Do not use treadmill in any location that is not temperature controlled, such as but not limited to garages, porches, pool rooms, bathrooms, car ports or outdoors. Failure to comply may void the warranty.

•

An appliance should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or taking off parts.

Close supervision is necessary when this appliance (or treadmill) is used by, on, or near children, invalids, or disabled persons.

Use this appliance (or treadmill) only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

Never operate this appliance (or treadmill) if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance (or treadmill) to a service center for examination and repair.

Do not carry this appliance (or treadmill) by supply cord or use cord as a handle.

Keep the cord away from heated surfaces.

Never operate the appliance (or treadmill) with the air openings blocked. Keep the air openings free of lint, hair, and the like.

Never drop or insert any object into any opening.

Do not use outdoors.

Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

To disconnect, turn all controls to the off position, then remove plug from outlet.

Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.

•

When using an electrical appliance, basic precautions should always be followed, including the following. Read all instructions before using this appliance:

SAVE THESE INSTRUCTIONS

At NO time should pets or children under the age of 12 be closer to the treadmill than 10 feet. At NO time should children under the age of 12 use the treadmill. Children over the age of 12 should not use the treadmill without adult supervision.

TO REDUCE THE RISK OF ELECTRIC SHOCK:

Always unplug this appliance (or treadmill) from the electrical outlet immediately after using and before cleaning.

DANGER

TO REDUCE THE RISK OF INjURY TO PERSONS:

Stand on the siderails before starting the treadmill. Read Instruction Manual before using. Remove safety key when not in use and store out of reach of chidren.

WARNING

T4_T6_Rev.1.7.indd 4-5 10/19/06 9:21:50 AM

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

AS SEMBLY

IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE!

During the assembly process of the treadmill there are several areas that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. There should be no side-to-side play in the console masts or any forward and back play in the console assembly or handlebars. If there is any play in these areas, the treadmill has not been properly assembled. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

UNPACKING

Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Unpack the unit where it will be used. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

Before proceeding, find your treadmill’s serial number and model name located to the left of the on/off power switch and power cord and enter it in the space provided below.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOxES BELOW:

SERIAL NUMBER :

MODEL NAME:

* Refer to the SERIAL NUMBER and MODEL NAME when calling for service. * Also enter this serial number on your Warranty Card.

TOOLS INCLUDED

PARTS INCLUDED

1 Safety Key 1 Console Assembly 1 Power Cord 4 Hardware Bags 2 Hand Rails 2 Hand Rail Base Covers

2 Console Masts 2 Cup Holders 2 Hand Rail Sleeves

DISPLAY (T6 SHOWN)

WATER BOTTLE HOLDER

GRIP PULSE HANDRAILS

ON/OFF SWITCH CIRCUIT BREAKER

TRANSPORT WHEEL

POWER CORD

CONSOLE

SAFETY KEY PLACEMENT

MOTOR COVER

RUNNING BELT / RUNNING DECK

SIDE RAIL

ROLLER END CAP

CONSOLE MAST

REAR ROLLER

ADJUSTMENT BOLTS

If you have questions or if there are any missing parts, contact Customer Tech Support.

Contact information is located on the back panel of this manual.

For a complete exploded diagram, visit us at www.horizonﬁtness.com

5 mm Allen Wrench

6 mm T-wrench

8 mm T-wrench

Screwdriver

HAND RAIL

HAND RAIL SLEEVE

HAND RAIL BASE COVER

WARNING

T4_T6_Rev.1.7.indd 6-7 10/19/06 9:21:53 AM

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

A Open BLUE HARDWARE BAG.

B Connect the CONSOLE WIRES

from the CONSOLE to those from the top of the MAST.

C Attach CONSOLE to the

CONSOLE MASTS using 1 BOLT (D).

D Repeat on other side.

E Tighten all console bolts.

F Snap each of the CUP HOLDERS

firmly into the CONSOLE.

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before

completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.

PRE-AS S E M B LY

ASSEMBLY S T E P 1

BOLT (A) 15 mm Qty: 6

ARC WASHER (C) 8 mm Diameter Qty: 6

SPRING WASHER (B) 8 mm DIAMETER Qty: 6

PINK HARDWARE BAG CONTENTS :

ASSEMBLY S T E P 2

BOLT (D) 20 mm Qty: 2

BLUE HARDWARE BAG CONTENTS :

BOLT (A)

SPRING WASHER (B)

WASHER (C)

CONSOLE MAST

BASE FRAME

CONSOLE WIRES

BOLT (D)

CONSOLE

SUGGESTED METHOD FOR STARTING BOLT

CONSOLE WIRES

A Open PINK HARDWARE BAG.

B Connect the CONSOLE WIRES

from the BASE FRAME to the bottom of the CONSOLE MAST.

C Attach LEFT CONSOLE MAST

using 3 BOLTS (A), 3 SPRING

WASHERS (B) and 3 ARC WASHERS (C).

D Repeat on other side.

CUP HOLDER

* NOTE: Be careful not to pinch any

wires while assembling the masts.

* NOTE: Be careful not to pinch any

wires while assembling the console.

T4_T6_Rev.1.7.indd 8-9 10/19/06 9:21:57 AM

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

A Open WHITE HARDWARE BAG. B Slide HAND RAIL SLEEVE over

the top of the hand rail.

C Attach top of HAND RAIL to

the console extension using 2

SCREWS (G).

D Attach bottom of HAND RAIL to

the base frame using 1 BOLT (H), 1 SPRING WASHER (I) and 1 WASHER (j).

E Slide HAND RAIL SLEEVE firmly

against console.

F Repeat on other side.

ASSEMBLY S T E P 3

SCREW (G) 15 mm Qty: 4

BOLT (H) 30 mm Qty: 2

WASHER (J) 8 mm DIAMETER Qty: 2

SPRING WASHER (I) 8 mm DIAMETER Qty: 2

WHITE HARDWARE BAG CONTENTS :

HAND RAIL

HAND RAIL SLEEVE

WASHER (J)

BOLT (H)

SPRING WASHER (I)

SCREW (G)

YOU’RE FINISHED!

A Open ORANGE HARDWARE BAG.

B Attach HAND RAIL BASE COVER to

the base frame using 2 SCREWS (K).

C Slide HAND RAIL TRANSITION

PIECE and HANDLEBAR into CONSOLE.

C Repeat on other side.

D Be sure all bolts and screws are

tightened and secured on the treadmill.

ASSEMBLY S T E P 4

SCREW (K) 30 mm Qty: 4

ORANGE HARDWARE BAG CONTENTS :

SCREW (K)

HAND RAIL BASE COVER

HAND RAIL TRANSITION PIECE

T4_T6_Rev.1.7.indd 10-11 10/19/06 9:22:00 AM

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

BE FORE YOU BEGIN

CONGRATULATIONS! on choosing your treadmill. You’ve taken an important step in developing and

sustaining an exercise program! Your treadmill is a tremendously effective tool for achieving your personal fitness goals. Regular use of your treadmill can improve the quality of your life in so many ways.

HERE ARE JUST A FEW OF THE HEALTH BENEFITS OF EXERCISE:

• Weight Loss

• A Healthier Heart

• Improved Muscle Tone

• Increased Daily Energy Levels

The key to reaping these benefits is to develop an exercise habit. Your new treadmill will help you eliminate obstacles that prevent you from exercising. Inclement weather and darkness won't interfere with your workout when you use your treadmill in the comfort of your home. This guide provides you with basic information for using and enjoying your new machine.

LOCATION OF THE TREADMILL

Place the treadmill on a level surface. There should be 6 feet of clearance behind the treadmill, 3 feet on each side and one foot in front for folding and the power cord. Do not place the treadmill in any area that will block any vent or air openings. The treadmill should not be located in a garage, covered patio, near water or outdoors.

DO NOT STAND ON THE BELT

While you are preparing to use the treadmill, do not stand on the belt. Place your feet on the side rails before starting the treadmill. Start walking on the belt only after the belt has begun to move. Never start the treadmill at a fast running speed and attempt to jump on!

SAFETY KEY

Your treadmill will not start unless the safety key is placed in position. Attach the clip end securely to your clothing. This safety key is designed to cut the power to the treadmill if you should fall. Check the operation of the safety key every 2 weeks.

NEVER USE THE TREADMILL WITHOUT SECURING THE SAFETY KEY CLIP TO YOUR CLOTHING. PULL ON THE SAFETY KEY CLIP FIRST TO MAKE SURE IT WILL NOT COME OFF YOUR CLOTHING.

WARNING

3 feet

6 feet

3 feet

1 foot

WARNING

PROPER USAGE

Your treadmill is capable of reaching high speeds. Always start off using a slower speed and adjust the speed in small increments to reach a higher speed level. Never leave the treadmill unattended while it is running. When not in use, remove the safety key, turn the on/off switch to off and unplug the power cord. Make sure to follow the MAINTENANCE schedule in this manual. Keep your body and head facing forward. Do not attempt to turn around or look backwards while the treadmill is running. Stop your workout immediately if you feel pain, faint, dizzy or are short of breath.

Do not operate the treadmill if the power cord or plug is damaged. If the treadmill appears to not be working properly, do not use the treadmill.

MOVING

Your treadmill has a pair of transport wheels built into the frame. To move, firmly grasp the rear of the frame and carefully lift.

Our Treadmills are heavy, use care and additional help if necessary when moving. Failure to follow these instructions could result in injury.

WARNING

T4_T6_Rev.1.7.indd 12-13 10/19/06 9:22:02 AM

+ 16 hidden pages