Hoover Wet Dry Vac User Manual

Wet/Dry Vac
with Portable Blower and
Exclusive
two tank system
Owner’s Manual
Read these instructions before operating cleaner.
2
Important Safeguards!
When using an electrical appliance, always follow
basic precautions, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
Warning:To reduce the risk of fire, electric shock, or injury:
• Do not expose to rain; store indoors only.
• Connect to a properly grounded outlet only. See “Grounding Instructions”
• Wear eye protection when operating portable blower.
• Close supervision is necessary when any appliance is used by or near children. Do not allow vacuum cleaner to be used as a toy or to run unattended at any time.
• Keep hair, loose clothing, fingers, feet and all parts of body away from openings, or other moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.
• Do not vacuum or use blower near toxic or health endangering materials such as asbestos, pesticides, fertilizers, or anything that is poisonous.
• Do not vacuum explosive dusts or use cleaner or blower in areas that may contain explosive substances such as coal, grain, or any other fine, combustible material.
• Avoid picking up hard, sharp objects with the cleaner. They may damage the cleaner and the filter.
• Do not use without filters in place. Clean filters frequently when picking up very fine materials such as powder.
• Use extra care when cleaning on stairs.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, or anything that may reduce air flow.
• Do not pull or carry by cord, use cord as a handle, close door on cord or pull cord around sharp edges or corners. Do not run appliance over cord.
Keep cord away from heated surfaces.
• Always disconnect cord from electrical outlet before servicing the cleaner.
• Unplug cleaner when not in use. Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. Never handle plug or appliance with wet hands.
• If needed, connect to a suitable extension cord. See “Extension cord instructions”.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left out doors, or dropped into water, take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot).
• Use vacuum cleaner only for its intended use as described in the instructions. Use only attachments recommended by The Hoover Company; others may cause hazards.
Save these instructions!
Index
Assembly ....................................4-5
Cleaner Description.......................5
How to Use
Automatic Wet Shut-Off............6
Extension cord .........................6
Portable blower.........................7
Separate wet/dry tanks..........5-6
Single tank.................................6
If you have a problem ...................9
Important Safeguards ...................2
Maintenance
Authorized Service....................9
Emptying tank ...........................8
Filters .........................................8
Lubrication.................................8
Storage ...........................................7
Record and retain
The HOOVER cleaner you have purchased is designed for both wet and dry pick up and also has a portable blower.
The model and serial number are located on the portable blower. For your personal records, please enter the COMPLETE model and serial
numbers in the spaces provided and retain this information. Model number__________________________________________ Serial number___________________________________________ It is suggested that you attach your sales receipt to this owner’s manual.
Verification of date of purchase may be required for warranty service of your Hoover product.
Thank you for selecting a
HOOVER product.
This cleaner was inspected and
packaged carefully before being
shipped from the factory. If you
should happen to need assistance
during assembly or operation, call
1-800-944-9200 for an automated
referral of authorized service outlet
locations (U.S. only)
or
1-330-499-9499 to speak with a
representative in our
Consumer Response Center.
PLEASE DO NOT RETURN
THIS PRODUCT TO
THE STORE.
®
©1993 The Hoover Company www.hoovercompany.com
3
Grounding Instructions
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor (C) and grounding plug (A). The plug must be plugged into an appropriate outlet (B) that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER-
Improper connection of the equipment-grounding conductor can result in the risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated in sketch (A).
A temporary adapter (D) may be used to connect this plug to a 2­pole receptacle (G) if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (B) can be installed by a qualified electrician. The green colored rigid ear (E), lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. (F).
NOTE: In Canada, the use of a
temporary adapter is not permitted by the Canadian Electrical Code.
Questions or Concerns?
The Hoover Company wants to quickly resolve any concerns about your cleaner or questions regarding its use. Look on the list provided with the product for your local Hoover Factory Service Center or in the Yellow Pages under “Vacuum Cleaners - Household” for the nearest Authorized Hoover Warranty
Service Dealer (Depot) or call:
1-800-944-9200 for an automated
referral of authorized service outlet locations (U.S. only)
OR
1-330-499-9499 to speak with a representative in the Hoover Consumer Response Center.
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE OR SEND IT TO NORTH CANTON FOR SERVICE.
A
B
C
D
E
F
G
4
A
A
A
B
B
B
B
A
Carton contents
Remove parts from tank and identify the following:
A. Outer tank B. Inner tank C. Cleaner lid and portable blower D. Caster supports (4) E. Casters (4) F. Caster support screws (4) G. Reusable cartridge filter -
assembled to cleaner lid
H. Small foam filter - assembled to
inner tank
I. 1 1/4-inch tool set includes:
hose, 2 extension wands, wet/dry nozzle, squeegee insert, utility nozzle, and crevice tool
J. 2 1/2-inch tool set includes:
hose, 2 extension wands, blower nozzle, and utility nozzle.
K. Small float ball L. Small float cage M. Tool rack
1. Assembly
Attach caster supports and casters
Remove cleaner lid and inner tank. Turn outer tank upside down.
Match letters (A or B) on bottom of caster supports with letters on cleaner tank.
Then align square tabs (1) on supports with rails (2) on tank. Slide tabs onto rails until caster support (3) snaps in place.
Insert support screw into hole nearest tank. Tighten screw with a Phillips screwdriver.
Insert caster stem into hole on bottom of caster support. Press firmly until caster snaps into place.
Repeat with remaining casters and screws.
Turn cleaner tank right side up.
Attach small float cage
Turn inner tank upside down.
Place float ball over round opening in bottom of tank.
Snap tabs (A) on float cage into slots (B) on tank.
Once in place, do not remove the float assembly.
NOTE: Do not attempt to remove
the large filter cage or float ball on cleaner lid. They are not removable parts.
Insert inner tank
With inner tank duct toward drain side of outer tank, align tab (C) on inner tank with slot (D) in outer tank; slide inner tank into place.
1-2
1-3
1-1
3
2
1
A
B
C
D
1-4
A
B
C
D
E
F
G
H
I
J
K
L
M
5
Attach cleaner lid
Rotate lid latches (E) outward. With wet/dry selector (F) toward drain side of tank align ribs (G) on front of tank with slots (H) on either side of hose inlets; place lid on tank.
Rotate latches inward to lock lid in place.
Note: For convenience in attaching
and removing the lid, finger holds are provided.
Attach tool rack
Slide the three tabs (I) on tool rack into slots (J) on back of cleaner lid. (To help locate the tool rack, guide lines have been added to tank lid.) Snap tool rack into place.
Attach hose, wands and cleaning tool
Push hose into hose inlet on tank; twist hose to tighten or loosen
connection. (See “How to use”
section for proper inlet selection.)
The wands and tools attach to hose in the same manner.
For convenience, additional tools store on tool rack when not in use.
Press squeegee insert firmly into wet/dry nozzle opening.
Use squeegee for wet pick-up only.
2. How to use
Attach Drain cap
Screw drain cap onto lower, front of tank as shown.
Additional tools and accessories that are not included with your model, are available at additional cost from your local Hoover Factory Service Center, Authorized Hoover Warranty Dealer, by using the enclosed order form or through The Hoover Company online at
www.hoovercompany.com
The assembled cleaner will look like the drawing.
Operate cleaner only at voltage specified on data plate on cleaner lid. This cleaner is intended for household use.
Cleaner Description
1. Portable blower
2. Blower latches
3. Cleaner lid
4. Hose inlets
5. Hose
6. Wet/dry selector
7. Caster supports
8. Casters
9. Tank drain cap
10. Cleaner tank
11. Wand storage holders
12. Wands: 2 1/2-inch wands fit
over 11/4-inch wands.
13. Carrying handles
14. Cleaner lid latches
15. ON/OFF switch
16. Tool storage rack
17. Cord hook: loop cord over
hook for storage.
18. 11/4-inch wands
19. 11/4-inch hose
20. Crevice tool
21. 11/4-inch utility nozzle
22. Wet/dry nozzle
23. Squeegee insert
24. 2 1/2-inch hose
25. 2 1/2-inch wands
26. 2 1/2-inch utility nozzle
27. Blower nozzle
E
E
G
F
H
J
I
1-5
1-6
1-7
2-1
1-8
1-9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6
Extension cord instructions
Use an outdoor, grounding type, SJT extension cord of 16 gauge (up to 35 feet) or 14 gauge (any length). The extension cord must employ a 3-prong grounding type plug and a 3-pole receptacle that accepts the machine plug.
Adapter
(Included with some models)
To use smaller diameter tools with the 21/2-inch diameter hose, attach the adapter (A) to hose. Attach tool to adapter.
Twist adapter and tool to tighten or loosen connection.
Separate wet/dry tanks
This feature allows you to change from wet pick-up to dry pick-up without having to empty the tank or change filters. Dry debris will collect in the inner tank and wet debris will collect in the outer tank.
Wear ear protection if operating cleaner for a prolonged period of time.
Make sure that the small foam and cartridge filters are in place.
Dry pick-up
Disconnect cleaner from electrical outlet.
With hose removed from cleaner, slide wet/dry selector (A) to expose “Dry tank inlet” (B). Selector will snap into place. Insert hose into “Dry tank inlet”.
Attach the desired tool to hose end.
Make sure cleaner lid is locked in place.
Plug power cord into a properly grounded outlet and turn cleaner
ON.
Wet pick-up
Disconnect cleaner from electrical outlet.
With hose removed from cleaner, slide wet/dry selector (A) to expose “Wet tank inlet” (C). Selector will snap into place. Insert hose into “Wet tank inlet”.
Attach desired tool (with squeegee if available) to hose end.
Make sure cleaner lid is locked in place.
Plug power cord into a properly grounded outlet and turn cleaner
ON.
Do not use cleaner as a pump to clean out clogged drains, sinks, or other plumbing fixtures.
If cleaner will not pick up, check filters. They may need to be cleaned or replaced (see “Maintenance” section).
Single tank operation
For picking up very large amounts of debris (either wet or dry), the cleaner may also be operated without the inner tank in place.
Disconnect cleaner from electrical outlet.
Remove inner tank and set aside.
Attach hose to either the wet or dry intake port. Plug power cord into a
properly grounded outlet and turn
cleaner on.
When using single tank for dry pick-up, cartridge filter must be in place.
For best results, when using single tank for wet pick-up, use a HOOVER® foam filter sleeve instead of the cartridge filter. See
“Filters” in the Maintenance section for availability of HOOVER® filters.
Automatic wet shut-off
When either tank is full of liquid, the automatic shut-off mechanism will shut off cleaner pick-up. When this happens, the motor sound will become noticeably higher in pitch. Turn cleaner off and empty tank to continue use.
The automatic shut-off will also engage if the cleaner has been tipped over. To continue use, turn cleaner off, and set it upright. Wait a few seconds to allow the motor to come to a complete stop.
The automatic shut-off will function for both separate wet/dry tank and single tank operation.
2-2
2-4
2-3
A
A
B
A
C
7
Drywall dust
For best results when picking up dry wall dust, slide wet/dry selector (A) to expose “WET/TANK INLET” (B) and make sure no water or moisture is in the tank (outer tank).
Keep inner tank in position. Insert hose into “WET TANK INLET”
and attach desired tool to hose end.
Portable blower
The blower can be used to blow dirt out of areas where it is impossible for suction to reach.
Disconnect cleaner from electrical outlet.
Inside of wand and tools must be free of litter before operating blower.
Removing blower
Rotate blower latches (A) to release blower. Lift blower off lid (B).
NOTE: Do not use blower handle
to lift or carry assembled cleaner while blower is attached to cleaner lid.
Attaching tools to blower
Attach a 2 1/2-inch wand and blower nozzle.
Plug cord into a properly grounded outlet and turn blower on.
To reposition blower, disconnect blower from electrical outlet. Remove wand;position blower on top of lid and secure latches.
CAUTION: Wear safety goggles
when using blower. Do not blow toward people, animals, or objects that may be damaged by flying debris.
Do not wear loose clothing or jewelry. Secure loose hair with a hat or hair net. Wear substantial footwear and long pants.
Wear ear protection if using the
blower for a prolonged period of time.
Do not use blower in wet or rainy
conditions. Turn blower off before setting
it down.
Storage
Empty tanks (see “Maintenance”
section). Rinse inside of tank
thoroughly with clean water particularly if spills or other liquid substances other than plain water have been picked up. Wipe inside
of tank dry.
Loop cord over cord storage hook, located on tool rack.
Wands store on rear caster supports. The larger diameter wands fit into outer triangle, the smaller diameter wands store inside the larger wands and over small triangular peg.
Tools store on tool rack as shown.
2-6
2-5
2-7
2-8
A
A
B
B
8
After wet pick-up
Unscrew drain cap (A) from bottom of outer tank. Empty contents into a suitable drain.
As the liquid level decreases, it may be necessary to tip cleaner to allow remaining liquid to drain out.
Rinse inside of tank thoroughly with clean water particularly if spills or other substances other than water have been picked up.
Wipe inside of tank dry.
Filters
Do not operate cleaner without filters in place.
Filters are available at your Hoover
Factory Service Center, Authorized Hoover Warranty Dealer (Depot), on the enclosed order form, or by writing to The Hoover Company, North Canton, Ohio, 44720.
To assure that your cleaner operates at peak performance, it is imperative that you use only genuine HOOVER filters distributed by The Hoover Company. HOOVER filters can be identified by these trademarks -
®
Foam filter
Disconnect cleaner from electrical outlet.
To clean, remove foam filter (B) and rinse with clean water. Let filter air dry.
To replace, slide filter completely down over openings on inner tank filter cage (C).
If the cleaner is used as a single tank unit for wet pick-up, it is best to use a HOOVER® foam filter sleeve, available at additional cost, instead of the cartridge filter.
Reusable cartridge filter
Disconnect cleaner from electrical outlet.
After dry pick-up, remove filter (D) and gently tap it against inside of cleaner tank or brush off debris with a soft brush.
After wet pick-up, allow filter to dry and gently brush with a soft brush.
Check filter thoroughly and replace it if there are any tears or holes in it.
If extremely dirty, the cartridge filter can also be rinsed occasionally with tap water.
NOTE: Vigorous scrubbing or
frequent rinsing may shorten the life of the cartridge filter.
To replace, slide cartridge filter over filter cage (E) until it will not go on any further.
Lubrication
The motor is equipped with bearings which contain sufficient lubrication for the life of the motor. The addition of lubricant could cause damage.
Do not add lubricant to motor bearings.
3-1
3-2
3-3
3. Maintenance
Emptying tanks
After dry pick-up
Disconnect cleaner from electrical outlet.
Release lid latches and remove cleaner lid from tank.
To avoid back strain, do not lift a full tank. First, scoop out enough debris to make tank easier to lift.
Empty contents into a suitable receptacle.
Rinse inside of tank with clean water and wipe dry.
Note: If not very full, the inner tank
may be easier to empty if it is removed from the outer tank.
When emptying the inner tank, do
not grab onto filter cage.
A
C
E
D
B
9
Problem: Loss of air suction
• Possible Cause
Possible Solution
• Obstruction in hose, wand or tool.
Clear obstruction.
• Clogged cartridge or foam filter.
Clean filter as described in “Maintenance” section.
• Hole/split in hose.
Inspect and replace hose.
• Automatic shut-off engaged.
See “Automatic wet shut-off” section
Service
To obtain approved HOOVER service and genuine HOOVER parts,
locate the nearest Hoover Factory
Service Center or Authorized Hoover Warranty Service Dealer (Depot) by:
• checking the Yellow Pages under “Vacuum Cleaners ­Household” OR -
• checking the list of Factory Service Centers provided with this cleaner OR -
• calling 1-800-944-9200 for an automated referral of authorized service outlet locations (U. S. only) OR -
• checking the Service section of
The Hoover Company online at
www.hoovercompany.com
Do not send your cleaner to The
Hoover Company in North Canton for service, this will only result in delay.
If further assistance is needed, contact The Hoover Company Consumer Response Center, North Canton, Ohio 44720 Phone: 330-499-9499.
In Canada, contact Hoover Canada,
Burlington, Ontario L7R 4A8, Phone: 1-800-263-6376.
Always identify your cleaner by the
complete model number when
requesting information or ordering parts. (The model number appears on the portable blower.)
If you have a problem
If a minor problem occurs, it usually can be solved quite easily when the cause is found by using the checklist below.
Problem: Cleaner won’t run
• Possible Cause
Possible Solution
• Not firmly plugged in.
Plug cleaner in firmly
• No voltage in wall plug.
Check fuse or breaker.
• Blown fuse/tripped breaker.
Replace fuse/reset breaker.
HOOVER and are registered trademarks
THE HOOVER COMPANY, NORTH CANTON, OHIO 44720
3-98 S6760 Litho USA 56514-020
®
®
®
HOOVER et sont des marques déposées
THE HOOVER COMPANY, NORTH CANTON, OHIO 44720
HOOVER y son marcas registradas
THE HOOVER COMPANY, NORTH CANTON, OHIO
Loading...