Hoover VL81 VL01001 User Manual

USER MANUAL

IMPORTANT SAFETY REMINDERS

This appliance should only be used for domestic cleaning, as
described in this user guide. Please ensure that this guide is
fully understood before operating the appliance.

GB

cigarette ends or other similar items.

Do not spray with or pick up flammable liquids, cleaning fluids,
aerosols or their vapours.

Do not run over the power cord when using your appliance or
remove the plug by pulling on the power cord.

Do not leave the appliance plugged in. Always switch off and
remove the plug from the socket after use, or before cleaning
the appliance or any maintenance task.

This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.

If the power cord is damaged stop using the appliance
immediately. To avoid a safety hazard, an authorised Hoover
service engineer must replace the power cord.

Keep hands, feet, loose clothing and hair away from rotating
brushes.

Use only attachments, consumables or spares recommended
or supplied by Hoover.

When using cleaning tools ensure that the appliance is kept in
the upright (parked) position. This will avoid possible damage
to the carpet or floor covering. When cleaning stairs, do not
position the appliance above you.

Static electricity: some carpets can cause a small build up
of static electricity. Any static discharge is not hazardous to
health.

Do not use your appliance out of doors or on any wet surface
or for wet pick up.

Do not continue to use your appliance if it appears faulty.

Hoover service: To ensure the continued safe and efficient
operation of this appliance we recommend that any servicing
or repairs are only carried out by an authorised Hoover service
engineer.

Do not stand on or wrap the cord around arms or legs when
using your appliance.

Do not use the appliance to clean animals or people.

When using the cleaning tools, ensure to always steady the
appliance with your other hand. This will ensure that the
appliance does not fall while in use.

WARNING: A thermal cut out switches off the appliance to prevent overheating
if it is used when full or there is a blockage or dirty filters. If this should
happen then switch off, unplug and correct the fault. It will take approximately
45 minutes for the cut out to automatically reset.

The Environment

The symbol on this appliance indicates that this appliance may not
be treated as household waste. Instead it must be handed over to the
applicable collection point for the recycling of electrical and electronic
equipment. Disposal must be carried out in accordance with local
environmental regulations for waste disposal. For more detailed
information about treatment, recovery and recycling of this appliance, please
contact your local city office, your household and waste disposal service or
the shop where you purchased the appliance.

This appliance complies with the European Directives 2006/95/EC,
2004/108/EC and 2011/65/EU.

Do not pick up hard or sharp objects, matches, hot ashes,

- 2 -

- 2 -

HOOVER Limited, Pentrebach, Merthyr Tydfil, Mid Glamorgan, CF48 4TU, UK

GETTING TO KNOW YOUR CLEANER

Effortless

GB

HOSE TO EXTENSION
TUBE CONNECTOR

cleaning
with your
new Hoover

HANDLE

UPPER HANDLE RELEASE

BUTTON

MINI TURBO NOZZLE *

BIN RELEASE BUTTON

CARRY HANDLE

INNER CYCLONES*

DUST BIN

POWER ON/OFF
BUTTON

BRUSH BAR ON/
OFF BUTTON

2-IN-1

TOOL

EXHAUST
FILTER COVER

EXHAUST FILTER

PRE-MOTOR
FILTER

HANDLE TUBE
RELEASE BUTTON

CORD STORAGE
HOOK

EXTENSION HOSE

CORD

CREVICE TOOL

This vacuum cleaner is
supplied with an Energy
Label as required by
European Regulation (EU) 665/2013.

* Certain models only

BRUSH BAR

EXTENSION
HOSE SOCKET

WHEELS

- 3 -

PREPARING YOUR CLEANER

Insert the main handle in the cleaner body
and then adjust handle up/down to the
desired height.

SUPPLY CORD

Do not run over the supply
cord.

Clip the supply cord in the cord
clip at the back of the handle
to avoid accidentally running
the cleaner over the cord and
causing any damage.

GB

Put 2-in-1 tool and crevice tool on
board storage area.

2

1

CLEANER RELEASE

Recline to unlock the cleaner

POWER SWITCH

Plug in your machine and
turn it on.

Twist the handle to manoeuvre under or around
furniture

MINI TURBO BRUSH ASSEMBLY*

Assemble the mini turbo brush holder to the
handle tube of the cleaner,then put the mini turbo
nozzle to the holder.

* Certain models only

BRUSH BAR SWITCH

Press the brush bar on/off
button at the top of the unit.
Brush bar on - carpet
Brush bar off - hard floor

- 4 -

GB

CLEANING TOOLS

Handle

All accessories can t onto the end of the hose, handle and handle tube.Combine accessories depending on use.

Mini Turbo Nozzle*

The Mini turbo nozzle* is ideal for removing pet hairs.
DO NOT touch the rotating brush.

Parquet Nozzle*

The parquet nozzle is ideal for cleaning delicate surfaces.

Connecting Accessory to Hose

Plug in the long stretch hose in

1

the hose socket.

Choose your accessory.

2

Connecting accessory to hose.

3

CLEANING THE STAIRS

It is dangerous to place the cleaner
above you when cleaning stairs.

ALWAYS work with the cleaner
below you. Ensure it is positioned
up against the bottom step.

Connecting accessory to Handle Tube

Remove handle tube. Connect hose to handle tube Connect accessory to the

1

IMPORTANT! When using cleaning tools, the cleaner must be kept in the upright position,

particularly when cleaning stairs. Hold unit while using hose or handle tube.

* Certain models only

2

1

2

3

handle tube.

- 5 -

STORING THE CLEANER

Turn the cleaner off and remove the plug. Wind the
power cord around the cord storage hooks.

GB

EMPTYING THE BIN

!

IMPORTANT: Before emptying the bin, make
sure vacuum cleaner has been switched off.

1

To remove the bin from the cleaner press the
bin release button.

Hold the container over

2

the Bin and press the
easy open button.

CLEANING THE PRE MOTOR FILTERS

1

Rotate the upper part of the dust bin to open.

Gently tap both lters to release

3

any excess dust.

2

Take out the pre-motor lter.

Wash both lter and sponge under warm water until

4

the water runs clean. Remove excess water by
shaking and leave to dry for 24 hours. Reassemble

and ret lters to cleaner, only when they are

completely dry.

<40

The bin door will open
and you can empty into a
bin with no dust contact.

Once emptied, gently tap

43

or shake the container to
release any excess dust.

Do not overfill the bin
above the max level line.

!

IMPORTANT! Ensure the pre-motor lter and
exhaust lters are reassembled to the cleaner before use.

CLEANING THE EXHAUST FILTER

The exhaust filter should be washed every month.
Remove the exhaust filter from your cleaner and wash
with lukewarm water.

Remove excess water by shaking and leave to dry for
24 hours. Refit filters only when completely dry.

- 6 -

CHANGING THE BELT OR BRUSHES CLEARING A BLOCKAGE

GB

If your cleaner is not picking up efciently, the belt or brushes (or both) may need replacing, but rst

please make sure you have:

• Emptied the bin

• Cleaned the lters

• Checked for blockages

Turn the cleaner over and remove 2 rear

1 4

rollers and 2 retaining screws.

Remove the brush guard.

2

IMPORTANT: Switch the cleaner off and

remove the plug from the electricity supply
before attempting any maintenance.

Hold the brush assembly and stretch the
belt until the brush can be slotted back
into the cleaner housing.

Rotate the brush to ensure free movement

5

of the belt.

IMPORTANT: Switch the cleaner off and
remove the plug from the electricity supply
before attempting any maintenance.

Check the cleaning
tools and hose for
blockages.

The hose can be
removed at both ends.

Turn the cleaner
over and rotate the
brushes to identify
any obstructions
including hair.

3

Remove brush assembly and check for
wear on the belt.
Loop the new belt around the
motor and brush channel.

NOTE: When the brush was blocked and stopped rotating,switch off and remove the plug from the
electricity supply,then use a pair of scissors to cut through any threads or hairs caught around the
brush. Reassemble the brush and brush guard.

Refit the brush guard with 2 retaining screws

6

and 2 rear rollers..

- 7 -

Check for a blockage in
the hose socket. Use a
flexible rod to remove
any obstruction.

Removing a blockage from
the mini turbo nozzle.
Open the nozzle at each
side,lift cover and remove
the blockage.

*Certain models only

GB

User checklist

If your cleaner is not working properly run through the
following checklist.

1. Is there a working electricity supply to the cleaner?
Check with another electrical product.

2. Is the bin full or choked with fine dust?
To empty the bin, see the User Manual on P6.

3. Is the hose blocked?
To clear a blockage, see the User Manual on P7.

4. Is there a blockage in the cleaner base?
To clear a blockage, see the User Manual on P7.

5. Are the filters blocked?
To clean filters, see the the User Manual on P6.

6. Are the brushes rotating correctly?
To check the brushes, see the User Manual on p7.

7. Has the cleaner overheated?
If so, it will take about 30 minutes to reset.

If there is any doubt call the Hoover Service Office for advice. They may be able
to assist you over the telephone. A service charge will be made if the cleaner is
examined and found to be in working order, has not been assembled in accordance
with these instructions or has been used incorrectly. working order, has not been
assembled in accordance with these instructions or has been used incorrectly.

IMPORTANT INFORMATION

Hoover Service

Should you require service at any time, please contact your local Hoover Service
Office.

Hoover spares and Consumables

Always replace parts with genuine Hoover spares. These are available from your
local Hoover dealer or direct from Hoover. When ordering parts always quote
your model number.

USE ONLY HOOVER SPARES

CONSUMABLES & SPARE PARTS CODE

PRE-MOTOR & EXHAUST FILTER KIT U75 – 35601691

HOSE D155 – 35601690

AGITATOR Y34 – 35601689

BELT V36 – 35601692

PET HAIR REMOVER NOZZLE J44 – 35601064

PARQUET EXTRA NOZZLE G87PC – 35600655

WARNING!

A thermal cut out switches off the cleaner to prevent overheating if it is used when
full or there is a blockage or dirty filters. If this should happen switch off, unplug and
correct the fault.
It will take about 45 minutes for the cut out to automatically reset.

IMPORTANT: Do not run cleaner over the supply cord as this could damage the
supply cord insulation.

Quality

Hoover’s factories have been independently assessed for quality. Our products
are made using a quality system which meets the requirements of ISO 9001

GUARANTEE STATEMENT

The guarantee conditions for this appliance are as defined by our representative in
the country in which it is sold. Details regarding these conditions can be obtained
from the dealer from whom the appliance was purchased. The bill of sale or receipt
must be produced when making any claim under the terms of this guarantee.

Subject to change without notice.

- 8 -

Hoover Limited

Pentrebach

Merthyr Tydl

Mid Glamorgan

CF48 4TU

HOOVER CUSTOMER HELPINE

03444 995 599

PRINTED IN P.R.C.

48017168/01