HED 6612-80
This manual contains sections of Safety
Instructions,Operating Instructions,
Installation Instructions and Troubleshooting
Tips etc. Carefully reading it before using the
dishwasher will help you to use and maintain
the dishwasher properly.
To reviewthesection on TroubleshootingTips
will help you to solve some common problems
by yourself and not need to ask for the help of
professional technicians.
..................1
ControlPanel........................2
DishwasherFeatures................. 2
WashCycleTable.................... 3
WaterSoftener...................... 4
Detergent...........................5
RinseAid......................... 5,6
Loading the Dishwasher Rack . . . . . . . . 6,7
TurningOntheAppliance..............7
FilteringSystem..................... 8
CaringfortheDishwasher.......... 9...
The manufacturer, following a policy of constant
development and up-dating of the product, may
make modifications without giving prior notice.
AboutElectricityconnection . . . . . . . . . . 10
AbouttheUnicouple.................10
WaterConnection...................11
Dimensions........................11
Beforecallingforservice.......... 12,13
Under certain conditions, Hydrogen gas may be produced in a hot-water system that has not been used for
two weeks or more. HYDROGEN GAS IS EXPLOSIVE.
If the hot-water systemhas not been used for such a period, before using the dishwasher turn on all
hot-water faucets and let the water flow from each for several minutes. This willrelease any accumulated
hydrogen gas. As the gas is flammable, do not smoke or use an open flame duringthistime.
This appliance complies with international
safety standards, and is fitted with a plug with
earthconnectiontoensurecompleteearthing
of the product.
Before connecting the appliance to the mains
supply it is important to ensure:
That the supply socket is properly earthed.
That your electricity supply is capable of
meeting the consumption requirements
listed on the rating plate of your appliance.
Ensure that your product is properly earthed. In the
absence of adequate earthing you will notice that when
touching the metal parts of your appliance an
electrical dispersion can be felt, due to the presence of
a radio interference suppressor.
This appliance complies with Directives
89/336/EEC, 73/23/EEC and following changes.
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Do not touch the heating element during or
immediately after use.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic
items not so marked, check the manufactures
recommendations.
Use only detergent and rinse additives designed
for an automatic dishwasher. Never use soap ,
laundry detergent, or hand washing detergent
in your dishwasher. Keep these products out of
children.
Keep child away from detergent and rinse aid, keep
child away from the open door of the dishwasher,
there could still be some detergent left inside.
The door should not be left in the open position
since this could present a tripping hazards.
During installation, the power supply must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
Theapplianceis not intended for use by young
children or infirm persons without supervision.
Dishwasher detergents are strongly alkaline,they
can be extremely dangerous if swallowed.Avoid
contact with skin and eyes and keep children away
from the dishwasher when thedooris open.
Important: when the appliance location is on carpet
floors, attention must be paid so as to ensure that
there is no obstruction to the bottom vents.
Do not operate your dishwasher unless all
enclosure panels are properlyinplace. Open the
door very carefully if the dishwasher is operating,
there is a risk of water squirting out.
Do not place any heavy objects of stand on the door
when it is open. The appliance could tip forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely to
damagethe door seal;
2) Load sharp knives with the handles up to reduce
the risk of cut-type injuries.
When using your dishwasher, you should prevent
plasticitem from contacting with heating element.
If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a
hazard.
Please dispose of packing materials properly.
Use the dishwasher only for its intended function.
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.
Young children should be supervised to ensure that
they do not play with the appliance.
Checkthat the detergent receptable is empty after
completion of the wash cycle.
Cutlery is washed best if it is placed in the basket with
handles downwards.
Warning:
knives and other utensils with sharp points must be
loaded in the basket with their points down or placed in a
horizontal position.
1
To get the best performance from your dishwasher,read all operating instructions before using it for the
first time.
5
6
8
9
34
1
2
11
10
1 Pre-wash light: Blink dur ing pre-w ash.
2 Wash light: wash.blink during
3 Rinselight: b rinse.link dur ing
4 Drying light:b drying.linkduring
5
No Salt Indicator Light: comes on when there is not enough
salt in the softener (Certain model only).
6
Rinse Aid indicator light: comes on when there is not enough
rinse agent (Certain model only).
7 Washing Program Selector: Turn the knob clockwise to
select wash cycles.
7
1
2
3
8
8 ON/OFF Button: To turn ON/OFF the power supply.
NOTE: this model has a "broken remember" function, which
means that power supply broken down dur ing washi ng
will not reset the current washing program. So you can't
cancel a program by cutting off the power. pls see the
section entitled "change a program".
9 Power Light : To come on when the ON/OFF Button is Press d
down.
10 Start / Reset Button: Press this button to start or pause the
selected program. When the program start one of the lights
will blink.
11 Door Handle: Pull it to open the door.
e
4
5
6
14
Upper Basket
Spray Arms
2
3
Lower Basket
Water Softener
5
Detergent Dispenser
6
9
10
7
CupShelf
8
Silverware BasketMain Filter
9
Coarse Filter
2
11
10
Rinse Aid Dispenser
Drain pipe connector
11
Inlet pipe connector
12
12
Intensive
For the heaviest soiled loads,
such as pots,pans,casserole
dishes and dishes that have
been sitting with dried food
on them for a while.
Pre-wash
Pre-wash (45 C)
Wash (70 )°C
Rinse (75 )
Drying
°
°
C
10/30 gr
Economy
(EN 50242)
Delica te
Da ily 60 ’
Rapid
Pre-rinse
For normally soiled loads,
such as , plates,glasses
and lightly soiled pans.
standard daily cycle.
For lightly soiled loads,such
as plates,glasses,bowls and
lightly soiled pans.
Daily wash in only 1 hour.
Suitablefor normal soiled
dishes thatare to be washed
straightaftera meal (max8
plate settings).
A shorter wash for lightly soiled
loads (max 6 plate settings).
To rinse dishes that you
plan to wash later that day.
pots
Pre-wash
°
Wash (50 )
Rinse (70 )
Drying
Pre-wash
Wash (45 )
Rinse (65 )
Drying
Pre-wash
Wash (70 )
Rinse (65 )
Drying
Wash (50 )
Rinse (55 )
Drying
Pre-wash
C
°
C
°
C
°
C
°
C
°
C
°
C
°
C
5/25 gr
5/25 gr
25 gr
20 gr
Draw out the lower and upper basket, load the dishes and
1
push them back. It is recommended that loading the lower
basket first, then the upper one
" Loading the Dishwasher " ).
Pour in the detergent(see the section entitled,
2
"Salt,DetergentandRinseAid").
With a little force to ensure the door is properly closed.
3
NOTE:
perfectly.
Insert the plug into the socket.
4
The power supply is 220-240VAC 50Hz, the specification
ofthesocketis12A250VAC,Makesurethatthewater
supply is turned on to full pressure.
Pressthe ON/OFF button
5
Turn the knob located on the right of the control panel in
6
the clockwise direction until the number or the symbol
for the cycle
Press the button to start the washing.
7
When the washing is over, you can shut off the sw tch by
8
pressing on/off button.
If all the lights begin to glimmer, that indicates the machine is out of order, please turn off the main power and water supply
before calling a service.
A click could be heard when the door is closed
Start/Reset
(see the section entitled
i
Premise
has only been running for a short time. Otherwise, the detergent
may have already been released, and the appliance may have
already drained the wash water. In this case, the detergent
dispensermust be refilled(see the paragraph entitled " Loading
the Detergent " ).
1
2
3
NOTE: If you open the door when washing, the machine
will pause. When you close the door and press the
Start/Reset button, the machine will keep on working after
10 seconds.
The four programlights shows the state of the dishwasher:
a)All program lights off-----------------stand by
b)One of the program lights on-----------pause
c)One of the program lights blinking-------run
: A cycle that is underway can only be modified if it
Please press the Start/Reset button and last more than
three seconds, this will cancel the current programme.
(NOTE: turning off the appliance by pressing the on/off
button can not cancel the current programme, because
this model has a "broken remember" function.)
Turn around the to select the
desired programme.
Press the Start/Reset button to start the washing.
Washing Program Selector
3
If your model have not water softener, you may skip this section.
There are two ways to reduce the hardness: one way is using water softener, the other is using
water
detergent.
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliances is equippedwith a special softener that uses a salt specifically designed to eliminate lime and minerals from the
water.
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should be filled as follows:
Remove the lower basket and then unscrew and remove the cap from the salt
1
container.
If you are filling the container for the first time ,fill 2/3 of its volume with water.
2
3
Place the end of the funnel(supplied) into the hole and introduce about 2kg of
salt .It is normal for a small amount of water to come out of the salt container
4
Carefully screw t he cap back on.
1.
The salt container must be refilled when the salt warning light comes on. Though the salt container is filled
enough, the indicator light may not black out before the salt fully dissolve.
If there are spills of the salt, a soak program could be run to wipe them out.
2.
The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used.
This is intended to optimize andcustomize the level of salt consumption so that the salt consumption could be set proceed as
follows:
Unscrew the cap from the salt container.
1
There is a ring on the container with an arrow on it (see Figure to the side), if
2
necessary, rotate the ring in the anticlockwise direction from the "-" Setting
toward the "+" sign, based on the hardness of the water being used.It is
recommended that adjustments should be made in accordance with the following
schema:
WATER HARDNESS
°fH
0~10 0-5 0-1.0
10~25
25~50 14-28 2.5-5.0
>50
dH
5-14 1.0-2.5
>28 >5.0
mmol/l
Selector
Position
-
/
MED
+
Salt consumption
(gram/cycle)
0
20 60
40 40
60 25
Auto nomy
(cycles/2kgs)
/
Contact your local water board for information on the hardness of your water supply.
4
YOU MAY NOT ADD TOO MUCH DETERGENT TO PREVENT THE FORMATION OF DEPOSITS BECAUSE YOURDISHWASHERS
HAVE SPECIALLY-DESIGNED WATER SOFTENERS.
The dispenser must be refilled before the start of each wash cycle following the instructions provided in the" Wash Cycle
Table".Your dishwashers than conventional dishwashers. Generally, only one tables poon of
detergent is needed for a normal wash load. Also, more heavily soiled items need more detergent. Always add the detergent just
before starting dishwasher,otherwise it could get damp and will not dissolve properly.
IF THE WATER ISN'T TOO HARD, YOU MAY ALSO PREVENT THE FORMATION OF DEPOSITS BY ADDING DETERGENT.
The amount of detergent needed can vary due to differences in water hardness. To determine the water hardness in your area,
contact your local water utility or area water softening company. The harder the water, the more detergent you may need.
Remember, you should adjust the amount of detergent you use by small amounts until you find the correct amount.
uselessdetergentandrinseaid
To remove hard water spots, try the following:
Run di shes through a no rmal wash program.
Remove all metal dishware,such as cutlery, pans, etc.,
from the dishwasher.
Do not add detergent.
Pour two cups of vinegar into a bowl and set the bowl face
up on the lower rack of the dishwasher.
Runthe dishes through a normal washprogram.
If this doesn't work, try the same process with 1 / 4 cup of
citric acid crystals instead of vinegar.
Dishwasher detergent is corrosive! Take care to keep it out
of reach of children.
To open the dispenser, turn the cap to the "open"(left)
arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to
overfill.
Replace the cap by inserting it aligned with "op en" arrow
and turning it to the closed (right) ar row.
Use only detergent specifically made for use in dishwashers.
Keep your detergent fre sh and dry. Don't put powde r detergent
into the dispenser until You're ready to wash dishes.
The rinse aid is releasedduring the final rinse to prevent water
from forming droplets on your dishes that can leave spots and
streaks. It also improves drying by allowing water to "sheet" off
the dishes.
Your dishwashers are des igned to use liquid rinse aids . The
rinse aid dispenser is located inside the door next to the
detergent dispenser. To fill the dispenser,open the cap and
pour the rinse aid into the dispenser until the level indicator
turns completely black. The dispenser holds about 100 ml of
liquid rinse aid.
Be careful not to overfill the dispenser, because this could
cause over sudsing. Wipe away any spills with a damp c loth.
Don't forget to replace the cap before you close the dishwasher
door.
If you have soft water, you may not need rinse aid for it may
cause a white film to develop on your dishes.
A measured amount of rinse aid is released during the final rinse. As with detergent, the amount
of rinse aid needed for your dishes depends on the hardness of the water in your area. Too much
rinse aid can result in lather of foaming and cause cloudiness or steaks on your dishes. If the
water in your area is very soft, you may not need rinse aid. If you do,you can dilute the rinse aid
with an equal amount of water.
The rinse aid dispenser has six settings. Always start with the dispenser set on " 1 ". If spots and
poor drying are problems, increase the amount of rinse aid dispensed by removing the dispenser
lid and rotating the dial to "2". If the dishes still are not drying properly or are spotted, adjust the
dial to the next higher number until your dishes are spot-free. We suggest you to set on "4" .
(If only four settings we suggest you to set on "2".)
5
If there is no rinse aid warning light in the control panel, you can judge the amountof rinse aid by thefollowing means.The
black dot on the rinse aid dispenser indicates the amount of rinse aid in the dispenser.As the rinse aid diminishes, the size of
the black dot decreases. You should never let the rinse aid get below 1 / 4 full.
Astherinse aid diminishes, thesize oftheblackdot on therinse
aid level indicator changes, as illustrated below.
Full
3/4full
1/2full
1 / 4 full - Should refill to eliminate spotting
Empty
The upper rack is designed to hold more delicate and lighter dishware such as glasses, coffee and tea cup and saucers, as well
as plates, small bowls and shallow pans(as long as they are not too dirty).
Position the dishes and cookware so that they do not get moved by the spray of water.
The upper rack can be adjusted for height by putting wheels of different height into therails.
3
4
4
4
4
4
4
5
Cups
1
Small serving bowl
2
Large serving bowl
3
4
Glasses
2
1
4
4
4
SILVERWARE BASKET
Gravy ladle Serving spoon
4
7
7
7
SILVERWARE BASKET
6
1
5
Saucers
Dish
6
Dessert dishes
7
We recommend that you place large items which are most difficult to clean into the lower rack: pots, pans, lids,
serving dishes and bowls, as shown in the figure to the right.
It is preferable to place serving dishes and lids on the side of the racks in order to avoid blocking the rotation of the
top spray arm.
Pots, serving bowls, etc, must always be placed top down.
Deep pots should be slanted to allow water to flow out.
The bottom rack feature fold down tine rows so that larger or more pots and pans can be loaded.
Desse rt dishes
7
8
6
Ovalplatter
8
Soup plates
9
Dinner plates
10
Silverware basket
11
Silverware should be placed in the silverware basket with handles at the bottom: If therackhasside baskets,the spoonshould
be loaded individually into the appropriate slots, Especially long utensils should be plac ed in the horizontal position at the
front of the upper rack.
44
4444 444 444
1
11 111 111 111
5
55 555 555 555
33 33336
33 3333
8
2
22 222 222 222
Forks
1
2
Soup spoons
3
Dessert spoons
Teaspoons
4
Do not let any item extend through bottom.
5
Knife
Serving spoon
6
Gravy ladle
7
Serving fork
8
When the working cycle has finished, the buzzer of dishwasher will mooing 8 second ,then stop .
Turn off the appliance using the ON/OFF button, shut off the water supply and open the door of
the dishwasher. Wait a few minutes before unloading the dishwasher to avoid handling the dishes
and utensils while they are still hot and more susceptible to breakage. Theywillalsodrybetter.
A forgotten dish can be added any time before the detergent cup opens.
Open the door a little to stop the washing.
1
After the spray arms stop working ,you can open the door
2
completely.
It is dangerous to open the door when washing,because the hot water may be scaldedtoyou.
Add forgotten dis hes.
3
Close the door, the dishwasher will work after ten second.
4
7
For your convenience, we have placed the drain pump and filtering system within easy reach inside the tub. There are three
components of the filtering system: the main filter, the coarse filter, and the fine filter.
Main filter
1
Food and soil particles trapped by this filter are pulverizedby a special jet on the lower spray
arm and washed down the drain.
Coarsefilter
1
2
3
2
Larger items, such as pieces of bone or glass, that could clog the drain are trapped in the
coarse filter. To remove an item caught in this filter, gently squeeze the tabs on top of this
filter and lift it out.
3
Fine filter
This filter holds soil and food residue in the sump area and prevents it from being
redeposited on the dishes during a cycle.
If your dishwasher is left in an unheated place during the winter, ask a service technician to:
1
Cut off electrical power to the dishwasher. Remove
fuses or trip circuit breaker.
Reconnect the water inlet to the
4
water valve.
pipe
2
Turn off the water supply and disconnect the water
inlet pipe from the water valve.
Drain water from the inlet and water valve.pipe
Uncrew
It is necessary to cl ean the spray arms regularly for hard water chemicals will clogthe spray arm jets and bearings. To removethe
spray arm, screw off the nut to take out the washer on top of the spray arm and remove the arm. Wash the arms in soapy and warm
water and use a soft brush to clean the jets. Replace them after rinsing them thoroughly.
3
(Use a pan to catch the water.)
Filter assembly
For best performance and results, the filter assembly must be cleaned.
The filter efficiently removes food particlesfrom the wash water, allowing it to be
recirculated during the cycle. For this reason, it is a good idea to remove the larger
food particles trapped in the filter after each wash cycle by rinsing the semicircular
filter and cup under running water. To remove the filter assembly, pull on the cup
handle in the upward direction. The entire filter assembly should be cleaned at least
once a month.
To clean the coarse filter and the fine filter, use a cleaning brush. Then, reassemble
the filter parts as shown in the figures left and reinsert the entire assembly in the
dishwasher, positioning in its seat and pressing downward.
The dishwasher must never be used without the filters. Improper replacement of the
filter may reduce the performancelevel of the appliance and damage dishes and utensils.
Remove the plastic sump cover in the
5
tub the bottom and use a sponge to
soak up water in rubber boot.
Never run the dishwasher without the filters in place.
8
To clean the edge around the door, you should use only a soft warm, damp rag. Toprevent
penetration of water into the door lock and electrical components, do not use a spray cleaner
of any kind.
Also, never use abrasive cleaners or scouring pads on the outer surfaces because they will
scratch the finish. Some papers towels can also scratch or leave marks on thesurface.
Never use a spray cleaner to clean the door panel for it could damage the door lock and electrical components. It is not allowed
to use the abrasiveagent or some paper towel becauseof the risk of scratching or leaving spots on the stainless steel surface.
Something will occasionally move into the filters andthe drain pump. If this occurs, the drain
pumpsemployed in your dishwashersare designedto automatically reverse, ejecting the
item back into the sump area or down the drain. If you have to remove an obstacle from the
drain pump,before you remove the filters, you should turn off the power; Then removethe
small black insert from the sumparea. (You might want to remove any standingwater first).
Scoop out the item that is probably in the sump area and causes the obstruction. Remember
to replace the black insert before you put the filters back in.
After every wash, turn off the water supply to the
appliance and l eave the door slightly ajar so that
moisture and odors are not trapped inside.
Before cleaning or performing maintenance, always
remove the plug from the socket. Do not run risks.
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
Rather, use only a cloth and warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened with water and a little
white vinegar, or a cleaning product made specifically
for dishwashers.
When you go on holiday, it is recommenedthat you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leavethe door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming
within the appliance.
If the appliance must be moved, try to keep it in the vertical
position.If absolutely necessary,it can be positioned on
its back.
One of the factors that cause odors to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
9
Fused electrical supply is required-copper wire only.Time delay fuse or circuit breaker recommended and provide separate
circuitserving only this appliance. Outlet should be placed in adjacent cabinet.
Make sure that the plug on the appliance remains accessible after installation.
After making sure that the voltage and the frequency values for the current in the home
correspond to those on the rating plate and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into an electrical socket which is
earthed properly. If the electrical socket to which the appliance must be connected is not
appropriate for the , replace the socket ,rather than
using a adaptors or the like as they could cause overheating and burns.
The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.
Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below theminimum
consult our Service Department for advice.
If faucet has not threads: attach the faucet adapter to faucet, then tighten every screw
of the adapter. To prevent leaking your should tighten the adapter.
plug (installed by a qualified electrician)
Pull Unicouple and its hoses completely out from storage compartment located at rear of d ishwasher
1
and attach it to the faucet adapter.
Attach the Unicouple connector to the faucet adapter by depressing the collaratthetopoftheconnector.
2
When Unicouple is all the way up onto the adapter, release the collar. It willthensnapIntopositionto
lock the Unicouple in place. The Unicouple s small hose carries water from the faucet to the dishwasher.
Its large hose carries drain water to the sink. Be sure Unicouple is pointingtowardthesinkbowldrain
opening and the sink drain is open for water that will drain from your dishwasher. If your dishwasher
drains into a disposer, operate the disposer until it is completely empty before starting the dishwasher.
Connector of ModelⅠ
A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has one, it is
recommended thet the hose be disconnected and the hole plugged.
Turn off the water.
1
Release the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
2
room, from severe splashing.
3
Release Unicouple from faucet by depressing the collar at the top of the Unicouple connector.
1
Remove the power cord plug from the wall receptacle.
Disconnect Unicouple from faucet adapter.
2
3
Turn water fully on before starting the dishwasher.
'
10
Connect the cold water supply hose to a threaded 3/4(inch) connectorand make sure that it is
fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the water
run to make sure that the water is clear and free of impurities. If this precaution is not taken,
there is a risk that the water inlet can get blocked and damage the appliance.
The water supply to the appliance can also be connected to the house hot waterline
(centralized system, heating system),as long as it does not exceed a temperature of 60 C.
Connector of ModelⅡ
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent
cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to
facilitate proper installation.
In this case, the wash cycle time will be shortened by about 15 minutes and thewash
efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as those
for the connection to the cold water line.
Once the appliance is positioned,adjust the feet (screwing them in or out) to adjust the
height of the dishwasher, making it level. In any case ,the appliance should notbe inclined
mor e than 2 .
Insert the drain hose into a drain pipe with a minimum diameter of 4 cm, or let itrunintothesink,makingsuretoavoidbending
or crimping it. Use the special plastic support that comes with the appliance. The free end of the hose must be at a height
between 40 and 100cm and must not be immersed in water.
If the sink is 34 or higher from the floor, the excesswater in Unicouple hoses
cannot be drained directly into the sink. It will be necessary to drain excess
water from hoses into a bowl or suitable container that is heldoutside and lower
than the sink.
600
600
DIMENSIONS(mm)
850
1155
11
'
Fuse blown, or the
circuit breaker acted
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on
Water pressure is low
Overflow
'
Some audible sounds are
normal
Utensils are not secure
in the baskets or something
small has droppe d into
the basket
Motor hums Dishwasher has not been used regularly. If you do not use it
Improper detergent
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Check that the water supply is connected properly and
the water is turned on.
The system is designed to detect an overflow. When it
does, it shuts off the circulation pump and turns on the
drain pump.
Sound from soft food shredding action and detergent cup
opening.
To ensure everything is secured in the dishwasher.
often, remember to set it to fill and pump out every week,
which will help keep the seal moist.
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
Add 1 gallon of cold water to the tub. Close and latch the
dishwasher, then drain out the water by slowly turning the
Dial until a drain period is reached. Repeat if necessary.
Spilled rinse agent Always wipe up rinse agent
spills immediately.
Detergent with
colorant was used
Rinse agent dispenser
is empty
Improper program
Improper rack loading Make sure that the action of the detergent dispenser and
Extremely hard water
Low inlet
temperature
Overloading the
dishwasher
Improper loading
Old or damp powder
detergent
Empty rinse agent
dispenser
Incorrect dosage of
detergent
Make sure that the detergent is the one without colorant.
Make sure that the rinse agent dispense is filled.
Sel ect stronger program
spray arms are not blocked by large dishware.
To remove spots from glassware:
Take out all metal utensils out of the dishwasher.
Do not add detergent.
Choose the longest cycle.
Start the dishwasher and allow it to run for about
18 to 22 minutes, then it wi ll be in the main was h.
Open the door to pour 2 cups of white vinegar
into the bottom of the dishwasher.
Close the do or and let the dishwasher complete
the cycle. If the vinegar does not work: Repeat
as above, except use 1/4 cup (60 ml)of citric acid
crystals instead of vinegar.
12
Combination of soft
water and too much
detergent
Tea or coffee stains using a solution of 1/2 cup of bleach and 3 cups warm water
Use less detergent if you have soft water and select a
shortest cyc le to wash the glassware and to get them clean.
to remove the stains by hand.
You have to wait for 20 minutes after a cycle to let the heating
elements cool down before cleaning interior; otherwise, burns
will happen.
Iron deposits in wate r
can cause an overall film
Hard water minerals To clean the interior, use a damp sponge with dishwasher
Dial is not in the
'
position
Dishes block detergent
cups
Normal phenomenon
Aluminum utensils have
rubbed against dishes
This is normal A small amount of clean water around the outlet on
Overfill dispenser or rinse
aid spills
Dishwasher isn t level
OFF
'
You have to call a water softener company for a special filter.
detergent and wear rubber gloves. Never use any other cleaner
than dishwasher detergent for the risk of foaming or suds.
Turn the Dial to
OFF position and slide the door latch to the
left.
Re-loading the dishes properly.
There is some steam coming through the vent by the door
latch during drying and water draining.
Use a mild abrasive cleaner to eliminate those marks.
the tub bottom at the back of the tub keeps the water
seal lubricated.
Be careful not to overfill the rinse aid dispenser.
Spilled rinse aid could cause oversudsing and lead
to overflowing. Wipe away any spills with a damp cloth.
Make sure the dishwasher is level.
Longer inlet time.
Longer draining time.
Longer heating time,
but not reaching required temperature
Overfilled.
Failure of temperature sensor
Failure of temperature sensor
13
Faucets is not opened.
The installation position of the drain pipe is too high.
Malfunction of temperature sensor or of heating element.
Too much inlet water. .
Short circuit or break of temperature sensor
Open circuit or break of temperature sensor
Loading...