V5832A V5833A
V5832A/5833A,C
SMALL LINEAR VALVES PN16
FOR MODULATING AND ON/OFF-CONTROL
SPECIFICATION DATA
FEATURES
• Small size allows installation where space is limited
• Long stroke results in a high quality characteristic
• Soft seat provides low leakage rate and high
rangeability
• Reduced k
hydronic balancing
• Range of fittings available for different connections
(soldered, threaded)
• Adjustment cap for manual operation
• Flat surfaces on body to fit installation tools
• Flat sealing connections in standard sizes
• Valve inserts changeable without draining by using
insert replacement tool WV 108
• 40 mm distance between ports A/AB and the bypass
(V5833C, only)
values in the bypass to facilitate
VS
V5833C
GENERAL
These small linear valves are used in combination with small
electric linear valve actuators and thermoelectric actuators
for the control of hot and/or chilled water for fan coil units and
small reheaters/recoolers in electric/electronic temperature
control systems.
SPECIFICATIONS
Models Two-way V5832A
Three-way V5833A
Three-way with bypass V5833C
Operation Two-way stem up to open,
port A to B; Three-way stem up
to close, port A to AB
Nominal pressure rating PN16
Capacity index (k
Leakage rate ≤0.02% of k
Valve body
Material Brass
Size DN15 (1/2“), DN20 (3/4“)
Trim
Stem Stainless steel
Plug Brass
Suitable medium Water, with max. 50% glycol
Controlled water
temperature 2...120 °C
) see tables on page 2 and 3
VS
VS
® U.S. Registered Trademark EN0B-0308GE51 R1002
Copyright © 2002 Honeywell Inc. • All rights reserved
V5832A/V5833A,C SMALL LINEAR VALVES PN16
A
Modulating valves
Rangeability
Two-way valves 100:1
Three-way valves 100:1 for controlled port
Flow characteristic Equal percentage port A-AB,
linear for bypass port B-AB
Stroke 6.5 mm
On/Off valves
Stroke 2.5 mm
Dimensions see Fig. 4 on page 5
FLOW CAPACITIES AND CLOSE OFF PRESSURE RATINGS
TWO-WAY VALVES
Valve Close-Off Pressure (kPa) with Actuators
DN k
15 0.16 V5832A1004 1600 600 15 V5832A1012 1600 600 15 V5832A1020 1600 600 15 V5832A1038 1600 600 15 V5832A1046 1200 180 15 V5832A1053 1200 180 20 V5832A1061 400 50* -
20 V5832A1079 400 50* 15 V5832A4008** 1200 180 180
20 2.50 V5832A4016** 400 50* 50*
*Up to 1000kPa system pressure. **For on/off control, stroke 2.5mm.
VS
Order number
M6410C,L/M7410C,E
(180 N)
M4450/M8450
(90 N)
Z100/M7410A
(90 N)
THREE-WAY VALVES
Valve Close-Off Pressure (kPa) with Actuators
k
DN
15
15 0.40 0.25 V5833A1011 800 500 15 0.63 0.40 V5833A1029 800 500 15 1.00 0.63 V5833A1037 250 150 15 1.60 1.00 V5833A1045 250 150 20 2.50 1.60 V5833A1052 100 50 20 2.50 1.60 V5833A3009 240 - 20 4.00 2.50 V5833A1060 100 50 20 4.00 2.50 V5833A3017 240 - 15 1.60 1.60 V5833A4007* 250 150 150
20 2.50 2.50 V5833A4015* 100 50 50
*For on/off control, stroke 2.5mm.
VS
A-AB B-AB
0.25
k
VS M6410C,L/M7410C,E M4450/M8450 Z100/M7410
0.16 V5833A1003 800 500 -
Order Number
(180 N) (90 N) (90 N)
EN0B-0308GE51 R1002 2
V5832A/V5833A,C SMALL LINEAR VALVES PN16
A
THREE-WAY VALVES WITH BYPASS
Valve Close-Off Pressure (kPa) with Actuators
DN
k
VS
A-AB B-AB
k
VS M6410C,L/M7410C,E M4450/M8450 Z100/M7410
Order Number
(180 N) (90 N) (90 N)
15 0.25 0.16 V5833C1066 800 500 15 0.40 0.25 V5833C1009 800 500 15 0.63 0.40 V5833C1017 800 500 15 1.00 0.63 V5833C1025 250 150 15 1.60 1.00 V5833C1033 250 150 20 2.50 1.60 V5833C1041 100 50 20 2.50 1.60 V5833C1140 240 - 20 4.00 2.50 V5833C1058 100 50 20 4.00 2.50 V5833C1152 240 - 15 1.60 1.60 V5833C4003* 250 150 150
20 2.50 2.50 V5833C4011* 100 50 50
*For on/off control, stroke 2.5mm.
OPERATION
A built-in return spring in the two-way valve produces an
opening force. In the three-way valve and the three-way valve
with bypass, the spring produces a closing force on the A to
AB ports.
The valves are supplied with a screwed-on adjustment cap
for manual operation and for protection of the stem. This
allows the stem to be set up for filling or initial heating/cooling
during the building construction phase without the use of a
controller or actuator.
The small electric valve actuators as well as the
thermoelectric actuators provide automatic control over the
opening and closing movement of the valve stem.
TYPICAL OPERATION
All types of valves should be mounted in the return flow. If the
∆p-values exceed 60 kPa, attention should be paid to the
development of noise.
Two-Way Valves
Direction of flow always from port A to port B
Port B: Outlet
outlet
inlet
+
-
outlet
inlet
+
-
Three-Way Valves
These valves are preferably used as mixing valves, this
means:
Port AB: Total flow outlet
Port A: Controlled flow inlet
Port B: Bypass inlet
inlet
+
AB A
B
-
AB A
B
Fig. 2. Three-way valve operation
Three-Way Valves with Bypass
These valves simplify the installation, which is depending on
the layout of the pipework, as the bypass pipe is part of the
valve. The information for the normal three-way valves is also
valid for this type.
inlet
+
AB A
B
-
AB A
B
inlet
+
-
inlet
+
-
Fig. 1. Two-way valve operation
Fig. 3. Three-way valve with bypass
3 EN0B-0308GE51 R1002
V5832A/V5833A,C SMALL LINEAR VALVES PN16
MOUNTING
When installing the valve care must be taken that the flow
direction is correct (see section "Typical Operation"). The
valve must not be mounted with the stem pointing downward.
The adjustment cap must be removed from the valve only
when the actuator is fitted. The valve should be installed as
stress-free as possible with a tightening torque of 25 to
30 Nm.
The valve is supplied complete with mounting instructions.
The water quality must meet VDI 2035 requirements.
ACCESSORIES
Valves V5832A need two connection sets, valves V5833A three connection sets, and valves V5833C four connection sets.
Connection Pipe Size DN Order Number Connection Set Description
Soldering
External
Thread
*Cannot be purchased from Honeywell
12 mm
15 mm
R3/8"
R1/2"
Dimensions of Connection Sets Order Number
G1/2“
G3/4“
G1/2“
G3/4“
15
20
15
20
a c d
AC-15FS
AC-20FS
AC-15FT
AC-20FT
12 mm
15 mm
R3/8“
R1/2“
Consisting of 1 union nut,
1 solder bush, and 1 gasket
Consisting of 1 union nut,
1 tailpiece, and 1 gasket
AC-15FS
AC-20FS
AC-15FT
AC-20FT
EN0B-0308GE51 R1002 4
DIMENSIONS
A
r
A
r
A
r
A
A
*
Two-way valve
Three-way valve
6.
5
Str
ok
6.
5
Str
ok
e *
V5832A/V5833A,C SMALL LINEAR VALVES PN16
M30x1.5
18
6.5 Stroke*
*
M30x1.5
18
6.5 Stroke*
llow 130mm fo
the actuator and
clearance for
removal
llow 130mm fo
the actuator and
clearance for
removal
a b d
abd
DN15 56 G1/2A 34
DN15 56 G1/2A 34
DN20 66 11/8" x 14 BS 84
DN20 66 G3/4A 33
a b d
ab cd
DN15 56 G1/2
DN15 56 G1/2A 24.5 34
DN20 66 11/8" x 14 BS 84
DN20 66 G3/4A 33 33
33
34
33
c
c
a
a
Three-way valve with bypass
6.
5
Str
ok
*
6.5 Stroke*
M30x1.5
18
llow 130mm fo
the actuator and
clearance for
removal
ab cd
a b c d
DN15 56 G1/2
DN15 56 G1/2A 40 34
DN20 66 11/8" x 14 BS 84 40
DN20 66 G3/4A 40 33
40 34
33
Modulating valves, only (in the case
of on/off valves, the stroke amounts
to 2.5 mm and the closure distance
to 14 mm).
Fig. 4. Dimensions V5832A/V5833A,C in mm
5 EN0B-0308GE51 R1002
V5832A/V5833A,C SMALL LINEAR VALVE PN16
SPARE PARTS
Valve inserts are provided as spare parts for the V5832A and V5833A,C small linear valves. When the tool WV 108 is used,
the valve inserts can be changed without draining the system.
Order Number DN k
VS
V5832A1004 15 0.16 0902812
V5832A1012 15 0.25 0902811
V5832A1020 15 0.40 0902810
V5832A1038 15 0.63 0902809
V5832A1046 15 1.00 0902808
V5832A1053 15 1.60 0902807
V5832A1061 20 2.50 0902814
V5832A1079 20 4.00 0902815
V5832A4008* 15 1.60 0902813
V5832A4016* 20 4.00 0902816
*For on/off control
Order Number DN k
VS
V5833A1003 / V5833C1066 15 0.25 0902821
V5833A1011 / V5833C1009 15 0.40 0902822
V5833A1029 / V5833C1017 15 0.63 0902823
V5833A1037 / V5833C1025 15 1.00 0902824
V5833A1045 / V5833C1033 15 1.60 0902825
V5833A1052 / V5833C1041 20 2.50 0902826
V5833A3009 / V5833C1140 20 2.50 0902818
V5833A1060 / V5833C1058 20 4.00 0902827
V5833A3017 / V5833C1152 20 4.00 0902819
V5833A4007* / V5833C4003* 15 1.60 0902817
V5833A4015* / V5833C4011* 20 2.50 0902820
*For on/off control
Order Number
Valve Insert
Order Number
Valve Insert
The following valve inserts are interchangeable
• Two-way valves: k
• Three-way valves: k
Control Products
Honeywell AG
Hardhofweg
D-74821 Mosbach
Phone: (49) 6261 810
Fax: (49) 6261 81309
http://europe.hbc.honeywell.com
Subject to change without notice. Printed in Germany Manufacturing location certified to
0.16, 0.25, 0.40, and 0.63
VS
k
1.0 and 1.6
VS
k
2.5 and 4.0
VS
0.25, 0.40, 0.63, and 1.0
VS
k
2.5 and 4.0
VS
EN0B-0308GE51 R1002
Loading...