Honeywell TH2110DV, TH1110DV, TH2210DV, TH1210DV User Manual

PRO 2000 Series

Programmable Thermostat

Operating Manual

69-2799EFS-03

This manual covers the following models:

TH 2 110DV: For 1 Heat/1 Cool systems TH2210DV: For 2 Heat/1 Cool heat pump systems only

(Pull thermostat from wallplate and turn over to find model number.)

CAUTION: EQUIPMENT DAMAGE HAZ ARD.

To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C).

Need Help?

For assistance with this product please visit http://yourhome.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

Read and save these instructions.

® U.S. Registered Trade mark. Patents pe nding.

1 69-2799EFS—03

Table of contents

About your new thermostat

Thermostat features .............................2

Thermostat is preset, ready to go .......3

Quick reference to controls .................4

Quick reference to display ..................5

Programming & Operation

Set time and day ..................................6

Select system setting ..........................7

Select fan setting .................................8

Using program schedules .............9–10

Adjust program schedule ..................11

Program schedule overrides .......12–13

Compressor protection ......................14

Early Start ...........................................15

Appendices

Battery replacement ............................16

Customer assistance ..........................17

In case of difficulty ........................18–19

Limited warranty ..................................20

This thermostat is ready

to go!

Your new thermostat is preprogrammed and ready to go. See page 9 to check settings.

About your new thermostat

Your new Honeywell thermostat has been designed to give you many years of reliable service and easy-to-use, push-button climate control.

Features

• Backlit display is easy to read

• Displays ambient (measured) temperature at all times

• One-touch access to setpoint temperature

• Preset program settings

• Temporary and permanent override of schedule

• Early start ensures the right temperature at the right time

• Built-in compressor protection

3 69-2799EFS—03

This thermostat is ready to go!

Your new thermostat is pre-programmed and ready to go. All you have to do is set the time and day. Then check the settings below and change if needed:

1. Set time and day (required for proper operation) ............... See page 6

2. Select system setting: Preset to Off .................... To change, see page 7

3. Select fan setting: Preset to Auto ....................... To change, see page 8

4. Program schedules: Preset to energy-saving levels

while you’re at work or asleep........................ To change, see pages 9-11

ONE-TOUCH TEMP CONTROL: You can override the program schedule at any time, and manually adjust the temperature (see pages 12-13).

M34678

Quick reference to controls

Set: Press to set time/

day/schedule. Hold: Press to override

programmed temperature control.

Run: Press to resume program schedule.

Temperature adjustment

69-2799EFS—03 4 5 69-2799EFS—03

Screen Lit for 12 seconds when you press any button.

Fan

Set

Hold

Run

Auto

Cool

Off

Heat

E.M. Heat

Fan Switch (see page 8) On: Fan runs continuously. Auto: Fan runs only when heating

or cooling system is on. System switch (see page 7)

• Cool: Cooling system control.

• Off: All systems off.

• Heat: Heating system control.

• Em Heat: Emergency & Auxiliary Heat control. Compressor is locked out. (Select models only.)

M34803

Quick reference to display screen

Current day/time

(see page 6)

6:30

Set Lo

Batt

Wake

Set Schedule

Temporary

Heat

Setpoint indicator Appears when the setpoint temperature is displayed.

Low battery warning (see page 16)

Current program period Wake/Leave/Return/Sleep (see pages 9–10)

Set Schedule (see pages 9–10)

Temperature The ambient (measured) temperature is normally displayed. To view the setpoint temperature, press the Up or Down button once. The setpoint temperature will appear for five seconds.

System status Cool On: Cooling system is on. Heat On: Heating system is on. Aux On: Auxiliary heat is on.

(Only for heat pumps with this capability [select models only].)

When Heat On or Cool On is flashing, compressor protection is engaged (see page 14).

Set the time and day

Press SET, then adjust time.

Set

Hold

Set Time

6:30

Run

M34811

Press SET, then select current day.

Set

Hold

Run

69-2799EFS—03 6 7 69-2799EFS—03

Set Day

M34812

1. Press the SET button, then press

s or t to set the clock

time.

2. Press the SET button, then press

s or t to select the

day of the week.

3. Press RUN to save & exit.

Note: If the clock flashes, the thermostat will follow your settings for the Monday “Wake” time period until you reset the time and day.

M34678

Select the system setting

Fan

Auto

Cool

Off

Heat

E.M. Heat

Set SYSTEM switch to control the heating or cooling system.

Set

Hold

Run

The SYSTEM switch can be set to control your heating or cooling system, depending on the season.

• Cool: Cooling system control.

• Off: All systems are off.

• Heat: Heating system control.

• Em Heat: Emergency & Auxiliary Heat control. Compressor is locked out. (Select models only.)

CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible

compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C).

Select the fan setting

M34678

Set the FAN switch to Auto or On.

Fan

Set

Hold

Run

Auto

Cool

Off

Heat

E.M. Heat

Set FAN switch to choose whether the fan runs continuously or only as needed.

69-2799EFS—03 8 9 69-2799EFS—03

In “Auto” mode (the most commonly used setting), the fan runs only when the heating or cooling system is on.

If set to “On,” the fan runs continuously.

Save money by setting program schedules

It’s easy to program your system for maximum energy savings. You can program four time periods each day, with different settings for weekdays and weekends.

WAKE

6:00 am

LEAVE

8:00 am

RETURN

6:00 pm

SLEEP

10:00 pm

Set to the time you awaken and the temperature you want during the morning, until you leave for the day.

Set to the time you leave home and the temperature you want while you are away (usually an energy-saving level).

Set to the time you return home and the temperature you want during the evening, until bedtime.

Set to the time you go to bed and the temperature you want overnight (usually an energy-saving level).

Energy saving settings for maximum cost savings

This thermostat is pre-set to use energy saving program settings. We recommend these settings, since they can reduce your heating/cooling expenses. (See next page to adjust times and temperatures of each time period.)

Cool (Mon-Fri)Heat (Mon-Fri) Heat (Sat-Sun) Cool (Sat-Sun)

Wake

(6:00 am)

Leave

(8:00 am)

Return

(6:00 pm)

Sleep

(10:00 pm)

69-2799EFS—03 10 11 69-2799EFS—03

70 62 70 62

M34813

To adjust program schedules

Press SET 3 times, then adjust time.

6:30

Set

Hold

Run

MO TU WE TH FR

Set

Wake

Set Schedule

Press SET, then set desired temperature.

1. Press SET until Set Schedule is displayed.

2. Press s or t to set your weekday Wake time (Mo-Fr), then press SET.

3. Press s or t to set the temperature for this time period, then press SET.

4. Set time and temperature for the next time period (Leave). Repeat steps 2 and 3 for each weekday time period.

5. Press SET to set weekend time periods (Sa & Su), then press RUN to save & exit.

Note: Make sure the thermostat is set to the system you want to program (Heat or Cool).

M34814

Program schedule override (temporary)

Press to temporarily adjust temperature.

Set

Hold

Run

6:30

Temporary

Set

Wake

Press to cancel temporary setting and resume program schedule.

69-2799EFS—03 12 13 69-2799EFS—03

Press s or t to immediately adjust the temperature. This will temporarily override the temperature setting for the current time period.

“Temporary” will appear on the display and the current program period will flash.

The new temperature will be maintained only until the next programmed time period begins (see page 9).

To cancel the temporary setting at any time, press RUN.

Note: Make sure the thermostat is set to the system you want to control (heat or cool).

Program schedule override (permanent)

Press to permanently adjust temperature.

Set

Hold

Run

6:30

Set

Hold

Press to cancel “Hold” setting and resume program schedule.

M34816

Press HOLD to permanently adjust the temperature. This will override the temperature settings for all time periods.

The “Hold” feature turns off the program schedule and allows you to adjust the thermostat manually, as needed.

Whatever temperature you set will be maintained 24 hours a day, until you manually change it, or press RUN to cancel “Hold” and resume the program schedule.

Note: Make sure the thermostat is set to the system you want to control (heat or cool).

Built-in compressor protection

M34817

This feature helps prevent damage to the com-

6:00

Heat

Wake

Message flashes until safe restart time has elapsed.

69-2799EFS—03 14 15 69-2799EFS—03

pressor in your air conditioning or heat pump system.

Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait 5 minutes before restarting.

During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump model). When the safe wait time has elapsed, the message stops flashing and the compressor turns on.

Early Start

6:00

Heat

Wake

Early Start: This feature allows the heating or

cooling to turn on before the program start time, so the temperature is reached at the time you set. For example: Set the Wake time to 6 am, and the temperature to 70°. The heat will come on before 6 am, so the temperature is 70° by the time you wake at 6. The next time period is displayed when the system is activated before a scheduled time period.

M34817

Battery replacement

M34673

M34679

Pull at bottom to remove thermostat from wallplate.

Turn thermostat over, insert fresh AAA alkaline batteries, then reinstall thermostat.

Set

Hold

Cool

Run

69-2799EFS—03 16 17 69-2799EFS—03

Install two fresh AAA batteries when Lo Batt flashes on the screen. Lo Batt appears for 60 days before the batteries are depleted.

On On

Fan Fan

Auto Auto

Replace batteries once a year, or when you will be

Cool

Off

away for more than a month.

Heat

E.M. Heat

Most settings are stored in non-volatile (permanent) memory. Only the clock and the day must be set after you replace the batteries.

M34673

M34679

Customer assistance

Pull at bottom to remove thermostat from wallplate.

Turn thermostat over to find model number and date code.

For assistance with this product, please visit http://yourhome.honeywell.com.

Or call Honeywell Customer Care toll-free at 1-800-468-1502.

On On

Fan Fan

Auto

Set

Hold

Run

Auto

Set

Cool

To save time, please note your model number and date code

Cool

Off

Heat

E.M. Heat

before calling.

In case of difficulty

If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily.

Display is blank

Heating or cooling system does not respond

69-2799EFS—03 18 19 69-2799EFS—03

• Check circuit breaker and reset if necessary.

• Make sure power switch at heating & cooling system is on.

• Make sure furnace door is closed securely.

• Make sure fresh AAA alkaline batteries are correctly installed (see page 16).

• Set system switch to Heat (see page 7). Make sure the temperature is set higher than the Inside temperature.

• Set system switch to Cool (see page 7). Make sure the temperature is set lower than the Inside temperature.

• Wait 5 minutes for the system to respond.

In case of difficulty

Temperature settings do not change

Make sure heating and cooling temperatures are set to acceptable ranges:

• Heat: 40° to 90°F (4.5° to 32°C).

• Cool: 50° to 99°F (10° to 37°C).

“Cool On” or “Heat On” is flashing

“Heat On” is not displayed

“Cool On” is not displayed

• Compressor protection feature is engaged. Wait 5 minutes for the

system to restart safely, without damage to the compressor (see page 14).

• Set the System switch to Heat, and set the temperature level above the current room temperature (see page 7).

• Set the System switch to Cool, and set the temperature level below the current room temperature (see page 7).

2-year limited warranty

Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of two (2) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).

If the product is defective, (i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or (ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the determination whether the product

should be returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.

Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502.

69-2799EFS—03 20 21 69-2799EFS—03

+ 50 hidden pages