Honeywell STDW720, STDW820, STDW730, STDW770, STGW840 Professional Installation Manual

Honeywell Process Solutions

SmartLine Wireless Transmitter

Professional Installation Guide

34-SW-25-03

Revision 1

December 2018

Revision 1 SmartLine Wireless Transmitter Professional Installation Guide ii

Notices and Trademarks

Copyright 2018 by Honeywell International Inc.

Revision 1, December 2018

While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied
warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may
be stated in its written agreement with and for its customers.

In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and
specifications in this document are subject to change without notice.

Honeywell, PlantScape, Experion PKS, and TotalPlant are registered trademarks of Honeywell International Inc.
Other brand or product names are trademarks of their respective owners.

Honeywell Process Solutions

1250 W Sam Houston Pkwy S

Houston, TX 77042

Revision 1 SmartLine Wireless Transmitter Professional Installation Guide iii

About This Document

This document outlines professional installation requirements for the SmartLineTM Wireless Pressure
Transmitter

for the Honeywell OneWireless Network. Professional installation is required to comply with
certification

agency and legal requirements. This document must be adhered to for all installations of the Honeywell
SmartLine Wireless Transmitters.
Honeywell does not recommend using devices for critical control where there is a single point of failure

or where single points of failure result in unsafe conditions. OneWireless is targeted at open loop
control, supervisory control, and controls that do not have environmental or safety consequences. As
with any process control solution, the end-user must weigh the risks and benefits to determine if the
products used are the right match for the application based on security, safety, and performance.
Additionally, it is up to the end-user to ensure that the control strategy sheds to a safe operating condition
if any crucial segment of the control solution fails.

Revision Information

Document Name

SmartLine Wireless Transmitter Professional Installation

Guide

Document ID

34-SW-25-03

Revision Number

Publication Date

1st release

Revision 1

December 2018

References

The following list identifies all documents that may be sources of reference for material discussed in this
publication.

Document Title

Doc #

SmartLine Wireless Transmitter User’s manual

34-SW-25-01

OneWireless R310 Release Notes

OWDOC-X252-en-310A

OneWireless R310 Migration Users Guide

OWDOC-X258-en-310

OneWireless R310 Field Device Access Point Users Guide

OWDOC-X256-en-310

OneWireless R310 Wireless Device Manager Users Guide

OWDOC-X254-en-310

OneWireless R300 Experion PKS Integration Guide

OWDOC-X259-en-300

OneWireless R300 Wireless LAN Controller Configuration Guide

OWDOC-X255-en-300

OneWireless R300 Network Planning an Installation Guide

OWDOC-X253-en-300

Telephone and Email Contacts

iv SmartLine Wireless Transmitter Professional Installation Guide Revision 1

Support and contact info

For Europe, Asia Pacific, North and South America contact details, refer to the back page of this
manual or the appropriate Honeywell Support web site:

Honeywell Corporate www.honeywell.com
Honeywell Process Solutions https://www.honeywellprocess.com/*
Training Classes https://www.honeywellprocess.com/en-US/training

Telephone and Email Contacts

Area

Organization

Phone Number

United States and
Canada

Honeywell Inc.

1-800-343-0228 Customer Service
1-800-423-9883 Global Technical Support

Global Email
Support

Honeywell Process Solutions

[e-mail]

Symbol Definitions

Revision 1 SmartLine Wireless Transmitter Professional Installation Guide v

Symbol Definitions

The following table lists those symbols used in this document to denote certain conditions.

Symbol

Definition

ATTENTION: Identifies information that requires special consideration.
TIP: Identifies advice or hints for the user, often in terms of performing a task.

CAUTION

Indicates a situation which, if not avoided, may result in equipment or work (data) on
the system being damaged or lost, or may result in the inability to properly operate
the process.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury. It may also be used to alert against unsafe
practices.

CAUTION symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in the
manual.

WARNING: Indicates a potentially hazardous situation, which, if not avoided, could
result in serious injury or death.

WARNING symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in the
manual.

WARNING, Risk of electrical shock: Potential shock hazard where HAZARDOUS
LIVE voltages greater than 30 Vrms, 42.4 Vpeak, or 60 VDC may be accessible.

ESD HAZARD: Danger of an electro-static discharge to which equipment may be
sensitive. Observe precautions for handling electrostatic sensitive devices.

Protective Earth (PE) terminal: Provided for connection of the protective earth
(green or green/yellow) supply system conductor.

Functional earth terminal: Used for non-safety purposes such as noise immunity
improvement. NOTE: This connection shall be bonded to Protective Earth at the
source of supply in accordance with national local electrical code requirements.

Earth Ground: Functional earth connection. NOTE: This connection shall be
bonded to Protective Earth at the source of supply in accordance with national and
local electrical code requirements.

Chassis Ground: Identifies a connection to the chassis or frame of the equipment
shall be bonded to Protective Earth at the source of supply in accordance with
national and local electrical code requirements.

continued

Symbol Definitions

vi SmartLine Wireless Transmitter Professional Installation Guide Revision 1

Symbol

Description

The Factory Mutual® Approval mark means the equipment has
been rigorously tested and certified to be reliable.

The Canadian Standards mark means the equipment has been
tested and meets applicable standards for safety and/or
performance.

The Ex mark means the equipment complies with the requirements
of the European standards that are harmonized with the 94/9/EC
Directive (ATEX Directive, named after the French "ATmosphere
EXplosible").

For radio equipment used in the European Union in accordance
with the R&TTE Directive the CE Mark and the notified body (NB)
identification number is used when the NB is involved in the
conformity assessment procedure. The alert sign must be used
when a restriction on use (output power limit by a country at certain
frequencies) applies to the equipment and must follow the CE
marking.

The ISA100 Wireless Compliant logo indicates the device has
received ISA100.11a conformance certification and is registered
with the Wireless Compliance Institute, assuring device
interoperability.

CRN

Canadian Registration Number

Contents

Symbol Definitions

Revision 1 SmartLine Wireless Transmitter Professional Installation Guide vii

Contents

1. DESIGNATION, SCOPE AND PREFACE ............................................................ 1

1.1 Designation ................................................................................................................................... 1

1.2 Scope ............................................................................................................................................. 2

1.3 Preface .......................................................................................................................................... 2

1.4 Site survey .................................................................................................................................... 2

1.5 Abbreviations & Definitions ........................................................................................................ 3

2. FEDERAL COMMUNICATION COMMISSION (FCC) .......................................... 5

2.1 FCC Compliance Statement ........................................................................................................ 5

2.2 Industry Canada (IC) .................................................................................................................... 5

2.2.1 IC Compliance Statements .................................................................................................................... 5

2.2.2 RF Safety Statement ............................................................................................................................. 5

2.3 FCC and Industry Canada (IC) Identification Numbers ............................................................ 6

2.3.1 ISA100 Radios ....................................................................................................................................... 6

2.4 Intended Country Usage .............................................................................................................. 6

2.4.1 NORTH AMERICA ................................................................................................................................ 6

2.4.2 EUROPEAN UNION .............................................................................................................................. 6

3. SMARTLINE WIRELESS TRANSMITTER GENERAL DESCRIPTION ............... 7

3.1 Intended Used ............................................................................................................................... 7

3.2 SmartLine Wireless Transmitter ................................................................................................. 7

4. PRODUCT SPECIFICATION ................................................................................ 8

4.1 ISA100 Radio, 2.4 GHz ................................................................................................................. 8

4.2 SmartLine Wireless Transmitter User Environment ................................................................. 9

4.3 SmartLine Wireless Instrument Power Specifications ............................................................. 9

4.4 Weight ........................................................................................................................................... 9

4.5 Dimensions ................................................................................................................................. 10

5. CABLES .............................................................................................................. 11

5.1 SmartLine Wireless Transmitter with N Connectors Antenna or Lightning Arrestor

Cables..................................................................................................................................................... 11

5.2 Transmitter connection status .................................................................................................. 11

5.3 Antenna Lightning Arrestors .................................................................................................... 12

Contents

Symbol Definitions

viii SmartLine Wireless Transmitter Professional Installation Guide Revision 1

6. APPROVED ANTENNA TYPES/GAINS ............................................................. 13

6.1 Antenna Details .......................................................................................................................... 13

7. EQUIVALENT ISOTROPICALLY RADIATED POWER (EIRP) .......................... 14

7.1 EIRP LIMITS ................................................................................................................................ 14

8. SETTING TX POWER ......................................................................................... 18

8.1 TX Power Setting ........................................................................................................................ 18

9. AGENCY LABEL INFORMATION ...................................................................... 19

9.1 External FCC/IC Labels .............................................................................................................. 19

9.1.1 External FCC/IC Label ........................................................................................................................ 19

10. RF SAFETY, MAXIMUM PERMISSIBLE EXPOSURE (MPE) STATEMENT ..... 20

10.1 MPE Statement........................................................................................................................ 20

11. AGENCY COMPLIANCE .................................................................................... 21

11.1 Radio and EMC Certifications ............................................................................................... 21

11.1.1 Federal Communication Commission (FCC) ....................................................................................... 21

11.1.2 Industry Canada (IC) ................................................................ ........................................................... 21

11.1.3 European Telecommunications Standards Institute (ETSI) ................................................................. 21

11.2 Product Safety Agency Certifications ....................................................................................... 21

11.2.1 European Union Certification (CE-mark) ............................................................................................. 21

Contents

Tables

Revision 1 SmartLine Wireless Transmitter Professional Installation Guide ix

Tables

Table 1-1 – SmartLine Wireless Transmitter Types .................................................................... 1

Table 1-2 –Table of Abbreviations and Definitions ..................................................................... 3

Table 4-1 Specifications of ISA100 Radio Module in SmartLine Wireless Transmitter................ 8

Table 4-2 User Environment Specifications for SmartLine Wireless Transmitter ........................ 9

Table 5-1 Transmitter to Antenna or Lightning Arrestor Cable Specifications for SmartLine

Wireless with N connectors................................................................................................ 11

Table 6-1 Approved Antenna Types/Gains ............................................................................... 13

Table 7-1 Maximum EIRP Limits for ISA100 Radios ................................................................ 14

Table 7-2 ISA100 Transmit Power Settings for the antennas and cable lengths specified

above ................................................................................................................................ 16

Figures

Figure 3-1 SmartLine Wireless Pressure Transmitter showing 4 dBi Integral Antenna ............... 7

Figure 4-1 Dimensions of a typical SmartLine Wireless Transmitter with the 4 dBi Integral

Antenna Option.................................................................................................................. 10

Figure 6-1 Remote Antennas ................................................................................................... 13