Honeywell SiXOCC Quick Installation Manual

SiXOCC

Wireless Occupancy Sensor / Wireless Occupancy Sensor

QUICK INSTALLATION GUIDE

The Honeywell SiXOCC Occupancy Sensor is a wireless device
used with controllers that support Honeywell’s SiX™ series devices.

The SiXOCC combines security motion detection and automation
in one unit. Using automation mode allows the device to signal the
control to turn a light on or off and/or a thermostat to a
pre-programmed temperature.

NOTES: Lights controlled via Z-Wave devices have not been
evaluated by ETL.

GUIDE D'INSTALLATION RAPIDE

The Honeywell SiXOCC Occupancy Sensor is a wireless device used with
controllers that support Honeywell’s SiX™ series devices.

The SiXOCC combines security motion detection and automation in one
unit. Using automation mode allows the device to signal the control to
turn a light on or off and/or a thermostat to a pre-programmed
temperature.

NOTES: Lights controlled via Z-Wave devices have not been
evaluated by ETL.

MOUNTING LOCATIONS / EMPLACEMENTS DE MONTAGE

OPEN / OUVERT

MOUNTING OPTIONS / OPTIONS DE MONTAGE

NOTE: After enrolling and before mounting
permanently, conduct go/no go tests
(see controller’s instructions) to verify
adequate signal strength.

NOTE: Après avoir enrôlé l'unité et avant de
la mettre en place de façon
permanente, effectuez des tests tout
ou rien (voir les instructions du
panneau de commande) pour vérifier
que la puissance du signal est
adéquate. Au besoin, modifiez
l'emplacement ou l'orientation du
dispositif.

ENROLL THE SIXOCC/ ENRÔLEMENT DU DÉTECTEUR

After enrolling, update the SiXOCC firmware (via the Controller)

to ensure the latest version is used. See the Controller’s
instructions.

NOTE: Once enrolled, the device cannot be used with another
system until it is removed from the current controller.

See the controller’s instructions.

Après l'enrôlement, faites la mise à jour du microprogramme du SiXOCC (via le

panneau de commande) afin de vous assure qu'il utilise la plus récente version.
Reportez-vous aux instructions du panneau.

NOTE : Une fois enrôlé, le dispositif ne peut pas être utilisé avec un autre
système avant d'avoir été supprimé du panneau actuel.

Reportez-vous

aux instructions du panneau.

To enroll in Honywell’s Lyric control panel follow the steps below:

WALK TEST / TEST PAR DÉPLACEMENT

NOTE: Before using Test Mode, the device must first be enrolled in

the Controller.

When in walk test the LED shows red for intrusion and green for
occupancy.

NOTE: Avant d'utiliser le mode de test, le dispositif doit d'abord être enrôlé

dans le panneau.

When in walk test the LED shows red for intrusion and green for occupancy.

Ê800-23891ZŠ

800-23891 2/18 Rev A

Honeywell is a registered trademark of Honeywell International Inc. All other trademarks are the properties
of their respective owners. All rights reserved.

Honeywell est une marque déposée de Honeywell International Inc. Toutes les autres marques de

commerce appartiennent à leurs propriétaires respectifs. Tous droits

DETECTION PATTERNS / CHAMPS DE DÉTECTION

LED INDICATORS

GENERAL STATUS PATTERN TIME DURATION OCCASION

No programmed network (Green LED)

100ms ON, 100ms OFF

8 seconds

Powered on, but never connected to a n etwork

Programmed into a network (Green LED) 3s ON / 3s Off Continuously?

Power on, connected to a network (even if already
enrolled into another network)

Selection (Red LED)

ON selected; OFF when cancel

The time of selection

When the user select’s it, command from 5168

Warm Up (Red LED)

1s on, 1s Off

6-45 seconds

Power on or Reset

RED LED

Enter/Exit walk test mode

20ms ON, 20ms OFF

2 seconds

Enter or Exit Walk Test mode

Trouble / Tamper 200ms ON, 4800ms OFF Flash if the error exists Any trouble condition?

Alarm no Pet Immunity / Pane l programmable

100ms ON, 100ms OFF

3 seconds

Alarm in walk test mode

Alarm with Pet Immunity / Pa nel programmable

3s ON, 3s OFF

3 seconds

Alarm in walk test mode

GREEN LED (INTRUSION)

Off

N/A

N/A

Normal operation when no activity detected

Delete

100ms ON, 100ms OFF

2 seconds

During enrolment

Tamper/Trouble

200ms ON, 1800ms OFF

10 minutes

Tamper triggered or Any trouble condition?

GREEN LED (OCCUPANCY)

Occupancy Alarm

3s ON

3 seconds

Alarm in walk test mode

GREEN LED DURING THE ENROLLMENT

3s ON / 3s OFF

3 seconds

Process is complete and enrollment confirmed

SPECIFICATIONS/SPÈCIFICATIONS

Battery / Pile ...................................................................................................................................... 3-volt lithium; Duracell DL123A, Panasonic CR123A, or HUIDERUI CR123A. /

3 volts’ au lithium; Honeywell 466

Range / Portée : ................................................................................................................................ 40’ x 56’ / 12 m x 17 m

Wall Mounting Height / Hauteur de mo ntage au mur : ............................................... 7’ – 9’ (2.1 m – 2.7 m); Optimal 7’6” (2.3 m).

RF Frequency / Fréquence RF .................................................................................................. 2.4 GHz

Tamper / Interrupteurs antisabot age: .................................................................................. Cover and Wall / Couvercle et mur: – reported separately to controller /

reported separately to controller

Dimensions / Dimensions .......................................................................................................... 4.5 in. diameter / 11.4 cm diamétre, 2.5” deep / 6.3 cm profound

Relative Humidity / Humidité de fonctionnement ......................................................... 95% (Agency Compliance – 93%), Non-condensing /

95% max. (Agence de conformité - 93% max.) sans Condensation

Operating Temperature / Température de fonctionnement : ................................... 32° – 122°F / 0° – 50°C

Weight / Poids: ................................................................................................................................. 3.97 oz / 112.67g (net weight)

BATTERY REPLACEMENT / REMPLACEMENT DE LA PILE

RF EXPOSURE Warning – The antenna(s) used fo r this device must
be installed to provide a separation distance of at least 7.8 inches
(20 cm) from all persons and mus t not be co-located or operating in
conjunction with any other antenna or tr ansmitter except in
accordance with FCC multi-transmitter product procedures.
Mise en Garde Exposition aux Frequences Radio: L'antenne (s)

utilisée pour cet émetteur doit être installée à une distance de
séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.

BATTERY CAUTION:
Risk of fire, explosion and burns.
Do not recharge, disassemble,
heat above 212° F (100° C) or
incinerate. Dispose of used
batteries properly. Keep away
from children.

ATTENTION DE BATTERIE :
Risque d'incendie, d'explosion et
de brûlures. Ne rechargez pas,
démonter, chauffer au-dessus de
212° F (100°C), ou incinérer.
Débarrassez-vous des batteries
utilisées de façon appropriée.
Gardez à partir des enfants.

Approval Listings / Approba tions Homologations

FCC / IC
cETLus Listed
Conforms to UL 639
/ Certified to

ULC-S306-03

Other Standards:
SIA-PIR-01
RoHS

PRODUCT MUST BE TESTED AT LEAST ONCE EACH YEAR /
LE FONCTIONNEMENT DU PRODUIT DOIT ÊTRE VÉRIFIÉ AU

MOINS UNE FOIS PAR ANNÉE

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM
SYSTEM. /’ OUR LES LIMITES DU SYSTÈME D’ALARME AU COMPLET, REPORTEZ-VOUS AU GUIDE D’INSTALLATION DU PANNEAU DE COMMANDE.

FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or
User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Cet appareil est confo rme à la partie 15 des règles de la FCC & de R SS-210 des Industries Canada. Son fonctionnement est
soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit adccepter
toute interférenc e reçue y compris les interférences ca usant une reception indésir able. réservés.

U.S. Warranty / U.S. Garantie:

http://www.security.hon eywell.com/hsc/resources/wa/index.
html

Support / Soutien: https://mywebtech.honeywell.com/ |
Patents / Brevets: www.honeywel l.com/patents

For full details, refer to the installation instructions (document # 800-23973) at https://mywebtech.honeywell.com.