Honeywell Lyric, SIXSMOKE, SiX User Manual

This wireless heat / smoke

detector is intended for use with Honeywell controls that support SiX™ series devices.

FC: This wireless heat / smoke detector

is intended for use with

Honeywell controls that support SiX™ series devices.

SP: This wireless heat / smoke detector is intended for use with Honeywell controls that support SiX™ series devices.

PA: This wireless heat / smoke detector is intended for use with Honeywell controls that support SiX™ series devices.

Smoke Detector

Open

/ OPEN OPEN / OPEN

NOTE

: Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controller’s instructions,

FC: NOTE

: Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controller’s instructions,

SP: NOTE

: Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controller’s instructions,

PA: NOTE

: Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controller’s instructions.

Enroll / Enroll / Enroll / Enroll

To silenc e the detector:

Press the test switch or disarm the system at the controller. If the alarm condition continues, the detector is only quiet for 5 minutes. When programmed in one-go

all-go mode, the test switch will not silence the detector.

NOTE: After enrolling and before mounting permanently,

conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.

FC: NOTE

: After enrolling and before mounting permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and ori entation as necessary.

SP: NOTE

: After enrolling and before mounting permanently, conduct Go/No Go tests (see contr oller’s instructions) to verify adequate signal strength. Adjust the device location and ori entation as necessary.

PA: NOTE

: After enrolling and before mounting permanently, conduct Go/No Go tests (see contr oller’s instructions) to verify adequate signal strength. Adjust the device location and ori entation as necessary.

Mount / Mount /

Mount / Mount

For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.

NOTE

: All smoke detectors programmed in the panel to operate in one-go-all-go mode will

sound on alarm.

FC: For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.

NOTE

: If programmed in the panel to operate in one-go-all-

go mode, all smoke detectors in the

system will sound on alarm

SP For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.

NOTE

: If programmed in the panel to operate in one-go-all-

go mode, all smoke detectors in the

system will sound on alarm

PA: For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.

NOTE

: If programmed in the panel to operate in one-go-all-go mode,

all smoke detectors in the

system will sound on alarm

*Use UL/ANSI A pproved canned smoke. / Use UL/ANSI Approved ca nned smoke. /

Use UL/ANSI Ap proved can ned smoke. / Use UL/ANSI Approved ca nned smoke.

Test / Test

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

Ê800-15961PŠ

800-15961 11/15 Rev C BETA2

LEDS and 85dB SOUNDER / LEDS and 85dB SOUNDER / LEDS and 85dB SOUNDER

/ LEDS and 85dB SOUNDER

Sounder

Status

Power Up – Enrollment /

Power Up – Enrollment / Power Up – Enrollment /

Power Up – Enrollment

Power Up – Device enrolled /

Power Up – Device enrolled / Power Up – Device enrolled/ Power Up – Device enrolled

Normal mode or Communicating

with the panel/

Normal mode or Communicating with the panel / Normal mode or Communicating with the panel / Normal mode or Communicating

with the panel

Maintenance1 / Maintenance1 /

Maintenance

1 /

Maintenance1

Test Alarm2 / Test Alarm2 /

Test Alarm

/ Test Alarm2

Heat Alarm3 / Heat Alarm3 /

Heat Alarm

/ Heat Alarm3

Smoke Alarm /

Smoke Alarm / Smoke Alarm /

Smoke Alarm

Low Battery / Low Battery /

Low Battery / Low Battery

Tamper Activated /

Tamper Activated / Tamper Activated / Tamper Activated

See Maintenance Section/ See Maintenance Section / See Maintenance Section /See Maintenance Section

Test activated by the test switch or from the panel / Test activated by the test switch or from the panel / Test

activated by the test switch or from the pa nel / Test activated by the test switch or from the pan el

≥ 135° F / 57° C or Temperature rise of ≥15° F ( 8.33° C) within 1 minute / ≥ 135° F (57° C) or Temperature rise of ≥15°

F (8.33° C) within 1 minute / ≥ 135° F(57° C) or Temperature rise of ≥15° F (8.33° C) within 1 minute /

Starts chirping after 7 days, continues until the batteries are repla ced or die / Starts chirping after 7 days, continu es

until the batteries are replaced or die / S tarts chirping after 7 days, continues until th e batteries are replaced or die /

Starts chirping after 7 days, continues u ntil the batteries are replaced or die

BATTERY CAUTIO N: Risk of fire,

explosion and burns. Do n ot recharge, disass emble, heat ab ove 212° F (100° C) or incin erate. Dispose of used batteries properly. Keep away from children.

FC:

BATTERY CAUTIO N

: Risk of fir e, explosion and burns. Do n ot recharge, disass emble, heat ab ove 212° F (100° C) or incin erate. Dispose of used batteries promptly. K eep away from children.

Replace Battery /

Replace Battery / Replace Battery

SP: BATTERY CAUTIO N: Risk of f ire, explosion and burns. Do not recharge, disassemble, heat above

212° F (100° C) or in cinerate. Dispo se of used batt eries promptly. K eep away from children. PA:

BATTERY CAUTION

: Risk of fi re, explosion and burns. Do not recha rge, disassembl e, heat abo ve

212° F (100° C) or incin erate. Dispose of used batter ies promptly. K eep away from children.

Approval Listings:

FCC / IC ETL Listed to UL639 cETL Listed to ULC S306-03

RoHS

Specifications:

Range:

0’- 25’/ 0 – 7.6m; Selec table

RF Frequency

: 2.4GHz

Battery

: 2 x 3V, Lithium; Panasonic CR123A, Duracell DL 123,

Duracell DL 123A, Honeywell 46 6

Tamper

: Wall

Operating Temperature

: 32° – 95° F / 0° – 35° C

Relative Humidity

: 95% max. (Agency Complia nce – 93% max.),

non-condensing

Dimensions

: 3.78” Diameter x 1.14” Th

ick / 96 mm Diameter x 29mm

Thick

Product must be tested at least once each year / Le fonctionnement du produit doit être vérifié au moins une fois par année / El producto debe ser probado al menos una vez al año / O produto deve ser testado pelo menos uma vez por ano

Support / Support / Support / Support

https://mywebtech.honeywell.com/

U.S. warranty / U.S. warranty / U.S. garantie / U.S. garantia

www.honeywell.com/security/hsc/resources/wa

FEDERAL COMMU NICATIONS COMM ISSION & INDUST RY CANADA STAT EMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation

Instructions or User's Manual. Unauthorized changes or modification s could void the user's authority t o operate the equipment.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: ( 1) Cet appareil ne doit pas causer d’interféren ces nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une reception indésirable.

RF Exposure War ning

– The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons an d must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures .

Mise en Garde Exposition aux Frequences Radi o:

L'antenne (s) utilisée pour cet émetteur doit être installée à une

distance de séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

MyWebTech

Warranty

Honeywell Lyric, SIXSMOKE, SiX User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual