Honeywell HZ-860, HZ-850 User Manual

IMPORTANT SAFETY
INSTRUCTIONS

WARNING –

THESE OPERATING AND SAFETY
INSTRUCTIONS BEFORE USING
THIS HEATER. IF YOU DO NOT
UNDERSTAND THESE INSTRUCTIONS
OR PRODUCT LABELS PLEASE CALL
OUR CUSTOMER REPRESENTATIVES
AT [phone] FOR ASSISTANCE
BEFORE USING THIS PRODUCT.

Warning – Failure to follow any of these
safety instructions could result in fire, injury
or death.

YOUR RESPONSIBILITIES

Electrical appliances may expose people to
hazards that can cause severe injury as well
as death. The use of electrical products may
create hazards that include, but are not limited
to, injury, fire, electrical shock and electrical
system damage. These instructions are
intended to provide you with the information
you need to use the product and to avoid such
hazards.

When using electrical appliances, basic
precautions should always be followed
to reduce risk of fire, electric shock, and
injury to persons including the following:

READ AND SAVE

The Honeywell trademark is used by Kaz USA, Inc. under license from Honeywell International Inc.

Honeywell International Inc. makes no representation or warranties with respect to this product

THERMAWAVE
CERAMIC HEATER

Model HZ-850 Series
Model HZ-860 Series

1. Warning – Read all instructions before
using this heater.

2. Warning

use. To avoid burns, do not let bare
skin touch hot surfaces. If provided, use
handles when moving this heater. Keep
combustible materials, such as furniture,
pillows, bedding, papers, clothes, and
curtains at least 3 feet (0.9 m) from the
front of the heater and keep them away
from the sides and rear.

3. Warning – Extreme caution is necessary
when any heater is used by or near
children or invalids, and whenever the
heater is left operating and unattended.

4. Warning – Always unplug heater when
not in use.

5. Warning – Do not operate any heater
with a damaged cord or plug or after the
heater malfunctions, has been dropped or
damaged in any manner. Discard heater or
return heater to manufacturer

6. Warning – For residential use only.

7. Warning – Do not use outdoors.

8. Warning – This heater is not intended

for use in bathrooms, laundry areas and
similar indoor locations. Never locate
heater where it may fall into a bathtub or
other water container.

9. Warning – Do not run cord under
carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Do not
route cord under furniture or appliances.
Arrange cord away from traffic area and
where it will not be tripped over.

– This heater is hot when in

1

10. CAUTION – THIS APPLIANCE HAS A

POLARIZED PLUG (ONE BLADE IS WIDER
THAN THE OTHER). TO REDUCE THE RISK
OF SHOCK, THIS PLUG IS INTENDED TO
FIT ONLY ONE WAY IN A POLARIZED
OUTLET. IF THE PLUG DOES NOT FIT
SECURELY IN THE OUTLET, REVERSE
THE PLUG. IF IT STILL DOES NOT FIT,
CONTACT A QUALIFIED ELECTRICIAN. DO
NOT ATTEMPT TO DEFEAT THIS SAFETY
FEATURE.

11. Warning – This heater draws 12.5 amps

during operation. To prevent overloading
a circuit, do not plug the heater into a
circuit that already has other appliances
working.

12. Warning – It is normal for the plug to

feel warm to the touch; however, a loose
fit between the AC outlet (receptacle)
and plug may cause overheating and
distortion of the plug. contact a qualified
electrician to replace loose or worn outlet.

13. Warning – To disconnect the heater,

first turn off the product, then grip the
plug body and pull it from the wall outlet.
Never pull by the cord.

14. Warning – Do not insert or allow foreign

objects to enter any ventilation or exhaust
opening as this may cause an electric
shock or fire, or damage the heater.

15. Warning – To prevent a possible fire, do

not block air intakes or exhaust in any
manner. Do not use on soft surfaces, like
a bed, or where openings may become
blocked.

16. Warning – A heater has hot and arcing

or sparking parts inside. Do not use it in
areas where gasoline, paint or flammable
liquids are used or stored.

17. Warning – Use this heater only as

described in this manual. Any other use
not recommended by the manufacturer
may cause fire, electric shock, or injury to
persons.

18. Warning – Always plug heater directly

into a wall outlet/receptacle. Never use
with an extension cord or relocatable
power tap (outlet/power strip).

19. Warning – Never tamper with this

product or attempt to fix it. Any tampering
with, or modification of this product can
result in serious injury, death, or fire. Risk
of electric shock. Do not open. No user
serviceable parts inside.

20. Warning – Do not remove product

labels that contain warnings or safety
instruction.

21. Caution – The output of this heater may

vary and its temperature may become
intense enough to burn exposed skin. Use
of this heater is not recommended for
persons with reduced sensitivity to heat
or an inability to react to avoid burns.

22. Caution – Before cleaning or storage,

or when not in use, turn the product’s
controls to the OFF position and unplug
the heater from the electrical outlet and
allow to cool.

23. Caution – Place the heater on a firm,

level, open surface free from obstructions
and at least 3 feet (0.9 m) away from any
combustible materials. DO NOT use on
an unstable surface such as bedding or
deep carpeting. Be sure the heater is not
in a position where it may be tripped over
by small children or pets. The heater’s
rubber feet will hold it firmly in position.

24. Caution – If your home has aluminum

wiring have a licensed electrician check
your receptacle’s connections. When
using a 1500 watt heater, aluminum wire
connections can cause a safety issue.

25.

SAVE THESE

INSTRUCTIONS

2

ABOUT CERAMIC TECHNOLOGY

Ceramic heaters generate heat by passing electricity through heating wires embedded in ceramic plates.
This type of heating technology provides fast, even heating.

The ThermaWave Ceramic Heater has an organic industrial design that maximizes heat output. It is
designed with fan power to improve convection in order to provide both all around or directional heating
comfort to you and your room.

ASSEMBLY

This heater requires simple, no tool assembly.

Unpack Main Body and Mounting Base (Fig. 1).

Place Mounting Base on a firm surface (upright in any direction). Place ThermaWave Main Body on
Mounting Base so Mounting Tabs are aligned with Base Slots. Press Main Body onto the Base until Tabs
snaps secure into the Slots (Fig. 2).

Fig. 1

Fig. 2

SET-UP

Place the heater on a firm, level, open surface free from obstructions and at least 3 feet (0.9m) away from
any wall or combustible material.

DO NOT use on an unstable surface such as bedding or deep carpeting.

BE SURE THE HEATER IS NOT IN A POSITION WHERE IT MAY BE TRIPPED OVER BY CHILDREN OR
PETS.

For best result, place heater on the floor to create warming room convection and allow heater to run for
5-10 minutes to reach maximum heat output.

MOVING THE HEATER

Turn off the heater.
Allow it to cool for ten (10) minutes.
Unplug heater and move. This heater is equipped with a Cool Touch Handle for your convenience.

3