Honeywell HZ-519 User Manual

R
E

W

PO

E
OD
M

PROFILE HEATER

HZ-519 Series

DIGITAL LOW

IMPORTANT
SAFEGUARDS

READ AND SAVE THESE
SAFETY INSTRUCTIONS
BEFORE USING THIS HEATER.

When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the
following:

IMPORTANT
INSTRUCTIONS

1. Read all instructions before using this heater.

2. This heater is hot when in use. To avoid burns, do not
let bare skin touch hot surface. If provided, use han­dles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding,
papers, clothes, and curtains at least 3 feet (0.9 m)
from the front of the heate r and keep them away f rom
the sides and rear.

3. Extreme caution is necessary when any heater is
used by or near children or invalids and whenever
the heater is left oper ating and unattended.

4. Always unplug heater when not in use.

5. Do not operate any heater with a damaged cord or
plug or after the heat er malfunctions, has been
dropped or damaged in any manner. Return heater
to authorized service facility for examination, electri­cal or mechanical adjustment, or repair.

6. Do not use outdoors.

7. This heater is not intended for use in bathroom, laun­dry areas and similar moist indoor lo ca tions. Never
locate heater where it may fa ll int o a bat ht ub or ot her
water container.

8. Do not run cord under carpeting. Do not cover cord
with throw rugs, runners, or the like. Arrange cord
away from traffic area where it will not be tripped
over.

9. This heater is for use on 120 volts. The cord has a
grounded plug as shown in

Fig. 1. An adapter is

www.sylvane.com 1-800-934-9194

available at retail (not included) for connecting three­blade grounding-type plugs to two-slot receptacles.
The green grounding lug ext ending from the adapter
must be connected to a permanent gro und such as a
properly grounded ou tlet box. T he adapter s hould not
be used if a three-slot grounded receptacle is avail­able.

10. This heater draws 12.5 amps during operation. To
prevent overloading a circuit, do not plug the heater
into a circuit that already has other appliances work­ing.

11. It is normal for the plug to feel warm to the touch;
however, a loose fit between the AC outlet (recepta­cle) and plug may cause overheat ing and distortion
of the plug. Contact a qualified electrician to replace
loose or worn outlet.

12. To disconnect the heater, first turn controls to the

OFF position, then grip the plug and pull it from the

wall outlet. Never pull by the cord.

13. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or da mage the heater.

14. To prevent a pos sible f ire, d o not bl ock ai r i nta kes or
exhaust in any manner. Do not use on soft surface,
like a bed, where openings may become blocked .

15. A heater has hot and ar cing o r spark ing p arts inside.
Do not use it in the areas where gasoline, paint, or
flammable liquids are used or stor ed.

16. Use this heater only as described in this manual.
Any other use not recommended by the manufac­turer may cause fire, electric shock, or injury to per­sons.

17. Avoid the use of an exte nsion cord because the
extension cord may overh eat and cau se a risk of f ire.
However, if you have to use an extension cord, the
cord shall be No. 14 AWG minimum size and rated
not less than 1875 watts.

18. The output of this heater may vary and its tempera­ture may become intense enough to burn exposed
skin. Use of this heater is not recommended for per­sons with reduced sensitivity to heat or an inability to
react to avoid burns.

19. SAVE THESE

INSTRUCTIONS.

1

IMPORTANT SAFETY INSTRUCTIONS
REGARDING THE PLUG ON YOUR
PRODUCT

•

MODE: SET TEMPERATURE

Set Temperature

Power

Mode

•FIG 1

BASIC CONTROL PANEL OPERATION:

POWER

Continuous Run

Power

Mode

70

Back-Lit

• Press Power once to turn the heater on.

• Press Power again to turn the heater off.

o

F

Back-Lit

• Press Mode until the T emperature icon blinks. The
current room temperature will appear.

• Use the Up or Down arrows to set the desired tem­perature.

• The Temperature icon will stop blinking and the cur­rent room temperature will reappear after the desired
temperature is set.

• The heater will turn-off shortly after the desired tem­perature is reached and the Power light above the
display will blink.

• The heater will turn back on when the room tempera­ture drops approximately 2 degrees below the
desired temperature. The Power light will stop blink­ing and will remain lit.

F/C

MODE: SET TIMER

Timer

F/C

Power

Mode

Back-Lit

• Press Mode until the Timer icon blinks. The Hour
display will appear.

• Use the Up or Down arrows to set an operation time
between 1 and 10 hours.

• The heater will turn-off when time runs out.

F/C

2

www.sylvane.com 1-800-934-9194