Honeywell FocusPRO 5000, FocusPRO 6000 User Manual

INSTALLER SYSTEM TEST

69-2026

INSTALLER SYSTEM TESTS

FocusPRO® 5000 Series

To begin, press and hold the s and t buttons until the

1. display changes.

Presss/t to turn system on/off.

System test System status number number

Done

Press NEXT to advance to next test.

3. Press DONE to terminate system test.

4. Proceed to Installer System Tests on page 8.

FocusPRO® 6000 Series

To begin, press and hold the s and t buttons until the

1. display changes.

Presss/t to turn system on/off.

System test System status number number

Done Next

Press NEXT to advance to next test.

3. Press DONE to terminate system test.

4. Proceed to Installer System Tests on page 8.

Test the system’s heating, emergency heat, cooling, and fan. Available tests vary by thermostat and system type.

System Test

Number

10 Heating system 0 Heat and fan off

20 Emergency

30 Cooling system 0 Compressor and

40 Fan system 0 Off

caution

Table 2. Installer System Test

Test Type System Status Number

heating system

EQUIPMENT DAMAGE HAZARD. Compressor protection is bypassed during testing. To prevent equipment damage, avoid cycling the compressor quickly.

and Description

1 First stage heat

on (Fan turns on if Setup Function 1 is set to 1, 5, 9, or 10 OR setup Function 3 is set to 1)

2 Second stage heat

3 Third stage heat

0 Heat and fan off 1 Heat and fan on 2 Second stage heat

(Aux. heat) turns on

fan off

1 Compressor and

fan on

2 Second stage

compressor on

1 On

FocusPRO® 5000

and 6000 Series

Thermostats

INSTALLER SETUP AND

SYSTEM TEST POCKET GUIDE

6 7 8

INSTALLER SETUP

FocusPRO® 5000 Series

To begin, press and hold the s and FAN buttons until

1. the display changes.

Press s or t to change settings.

Function Setting

Done

Press NEXT to advance to the next function.

3. Press DONE to exit and save settings.

4. Proceed to Installer Setup Functions on page 4.

2 3 4 5

FocusPRO

6000 Series

To begin, press and hold the s and FAN buttons until the display changes.

Press s or t to change settings.

Function Setting

Done Next

Press NEXT to advance to the next function.

3. Press DONE to exit and save settings.

4. Proceed to Installer Setup Functions on page 4.

INSTALLER SETUP FUNCTIONS

Available option and default settings vary by thermostat.

Setup functions Setting & Options

1 System type 0 1 heat / 1 cool Conv.

2 Changeover valve

3 Fan control

5 First stage heat

6 Second stage

7 Auxiliary heat

Table 1. Installer Setup

(O/B terminal)

(heating)

cycle rate

heat/Aux heat cycle rate

cycle rate

(factory default in bold)

1 1 heat / 1 cool heat

pump (no Aux. heat)

2 Heat only (2-wire, 3-wire

zone valves [Series 20], and normally open zone

valves) 3 Heat only with fan 4 Cool only 5 2 heat / 1 cool heat

pump (with Aux. heat) 6 2 heat / 2 cool Conv. 7 2 heat / 1 cool Conv. 8 1 heat / 2 cool Conv. 9 2 heat / 2 cool heat pump

(no Aux. heat) 10 3 heat / 2 cool heat

pump (with Aux. heat)

0 Controls valve in cooling

1 Controls valve in heating

0 Gas/Oil heat (equipment

controls heating fan)

1 Electric furnace (thermo-

stat controls heating fan)

5 Gas or oil furnaces of

less than 90%

efciency

1 Steam or gravity 3 Hot water systems or fur-

naces of 90%+ efciency

9 Electric furnaces

[Other options: 1–12]

5 Gas or oil furnaces of

less than 90% efciency

1 Steam or gravity 3 Hot water systems or fur-

naces of 90%+ efciency

9 Electric furnaces

[Other options: 1–12]

5 Gas or oil furnaces of

less than 90% efciency

1 Steam or gravity 3 Hot water systems or fur-

naces of 90%+ efciency

9 Electric furnaces

[Other options: 1–12]

Setup functions Setting & Options

8 Emergency heat

9 First stage

10 Second stage

12 Manual/Auto

13 Adaptive Intel-

14 Temperature

15 Compressor

16 Schedule format 0 5/2 (weekdays

26 Auxiliary heat

27 Heat temperature

28 Cool temperature

Functions 13 and 16 only available on the 6000 series; function 26 only available on the 5000 series

Table 1. Installer Setup

cycle rate

compressor cycle rate

changeover

ligent Recovery

display

protection

control

range stops

range stop

(factory default in bold)

9 Electric emergency heat

1 Steam or gravity 3 Hot water systems or fur-

naces of 90%+ efciency

5 Gas or oil furnaces of

less than 90% efciency [Other options: 1–12]

3 Recommended

[Other options: 1–6]

3 Recommended

[Other options: 1–6]

0 Manual changeover

(Heat/Cool/Off)

1 Auto changeover (Heat/

Cool/Auto/Off)

2 Auto changeover only

(Auto)

1 On

0 Off

0 Fahrenheit

1 Celsius

5 5-minute compressor

off time

[Other options: 0–4 minutes]

and weekends programmable)

1 5/1/1 (weekdays,

Saturday, and Sunday programmable)

0 Comfort

1 Economy

90 Max. heat temperature

setting is 90°F (32°C)

[Other options: 40–89°F (4.5°C to 32°C)]

50 Min. cool temperature

setting is 50°F (10°C)

[Other options: 51–99°F (10.5°C to 37°C)]

Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers.

Automation and Control Solutions

Honeywell International Inc.

1985 Douglas Drive North

Golden Valley, MN 55422

Honeywell Limited-Honeywell Limitée

35 Dynamic Drive

Toronto, Ontario M1V 4Z9

http://yourhome.honeywell.com