EMC levels Hospital Airp or t Residential Area Commercial Light Industry Area Heavy Industry
C O O - - - -
H R R R R O O
L - - - - R R
T R (IT Network)
O = Optional, R= Required
C = EN61800-3 Category C1 (with external RFI-filter in SmartDrive COMPACT)
H = EN61800-3 Category C2 (standard in SmartDrive COMPACT)
L = EN61800-3 Category C3 (standard in Honeywell inverters >160kW)
T =EN61800-3 IT network (e.g. ships) requirements fulfilled, units can be easily converted to T-class from
standard EMC class. Instructions for this can be found from manuals which can be downloaded from
Download Center on Honeywell inverter page http://ecc.emea.honeywell.com/inverter
EN0B-0638GE51 R1009 4
SmartDrive COMPACT VARIABLE FREQUENCY DRIVES
MECHANICAL DIMENSIONS AND MOUNTING
There are two possible ways to mount the SmartDrive Compact onto the wall; either screw or DIN-rail mounting. The mounting
dimensions are also given on the back of the inverter.
Forced air flow cooling is used in all SmartDrive Compact drives. Enough free space shall be left above and below the inverter to
ensure sufficient air circulation and cooling. SmartDrive Compact products can be mounted side by side. You will find the
required dimensions for free space and cooling air in the tables below:
Mechanical size Free space above [mm] Free space below [mm]
MI1 100 50
MI2 100 50
MI3 100 50
Mechanical size Cooling air required [m3/h)
MI1 10
MI2 10
MI3 30
5 EN0B-0638GE51 R1009
SmartDrive COMPACT VARIABLE FREQUENCY DRIVES
CABLING AND FUSES
Use cables with heat resistance of at least +70 °C. The cables and the fuses must be dimensioned according to the following
tables. The fuses function also as cable overload protection. These instructions apply only to cases with one motor and one
cable connection from the inverter to the motor. In any other case, ask the technical support for more information.
Connection Cable type
Mains cable Power cable intended for fixed installation and the specific mains voltage. Shielded cable not required.
Motor cable Power cable equipped with compact low-impedance shield and intended for the specific mains voltage.
Control cable Screened cable equipped with compact low-impedance shield (NKCABLES /Jamak, SAB/ÖZCuY-O or similar).
Push the navigation wheel for 5 seconds to move from remote
control (I/O or Fieldbus) to manual mode and back.
Only the most commonly used parameters visible in basic view to
provide easier navigation. The full view can be seen after P13.1
Parameter conceal is deactivated by changing the value to 0.
Parameter sets can be uploaded and downloaded with this tool.
The SmartDrive Compact does not have to be powered up since
the tool works with a 9V battery.
Compact and robust design with easy installation
Feature Functions Benefit
Compact size
Integrated RFI-filters
Single power rating
Max. ambient temperature
+50 °C
Side by side mounting
with screws or DIN-rail as
standard
Very compact size of the product compared to other similar
products from the market place
The units comply with EN61800-3 category C2 as standard. This
level is the required level for public electricity networks such as
buildings.
Single power suitable for both pump and fan or machine
applications
High maximum ambient operating temperature
SmartDrive Compact can be mounted side by side with no space
between the units either with screws or on DIN-rail as standard.
Dimensions for screw mounting can be found also on the back of
the inverter.
Fully configured inverter for
the application in question
Ready to accept 0-10V
analog speed signal in just
30 seconds
Single button operation to
change the control to manual
(keypad) and back. Useful
function when
commissioning and testing
applications
Easy navigation through the
most common parameters
Parameter copying easily
from 1 inverter to another
without even powering up the
products.
Automatically adjusts switching frequency to adapt to unusual
increase in ambient
Automatically lowers motor speed to adapt to sudden voltage
drop such as power loss
Auto restart function can be configured to make VFD restart
automatically once fault is addressed
Uninterruptible operation
Uninterruptible operation
Uninterruptible operation
VFD and motor control features
Feature Functions Benefit
Improved performance
Flying start
High switching frequency
Inbuilt PI- controller
Ability to get an already spinning fan under speed control
Honeywell SmartDrive COMPACT is capable of providing the
maximum power with high switching frequency.
Capability to make a standalone system with sensor connected
straight to the inverter and inverter doing the complete PIcontrol.
Important in clean room
production to ensure the
standard conditions
Low audible noise from the
motor
Cost saving
OPTIONAL ACCESSORIES
Option Order type code
IP21 enclosure upgrade kit for size MI1
IP21 enclosure upgrade kit for size MI2
IP21 enclosure upgrade kit for size MI3
SmartDrive Compact Parameter download/upload and PC interface tool with
SMARTDRIVE-USBC 3.0m USB-cable for PC connection
SmartDrive Compact Parameter download/upload without cable
SmartDrive 3.0m USB PC connection cable
COMP-IP21-KIT1
COMP-IP21-KIT2
COMP-IP21-KIT3
COMP-LOADER
COMP-LOADER-NC
SMARTDRIVE-USBC
9 EN0B-0638GE51 R1009
SmartDrive COMPACT VARIABLE FREQUENCY DRIVES
Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Rolle, Z.A. La Pièce 16, Switzerland by its Authorized Representative:
Automation and Control Solutions
Honeywell GmbH
Böblinger Strasse 17
71101 Schönaich
Germany
Phone: (49) 7031 63701
Fax: (49) 7031 637493
http://ecc.emea.honeywell.com
Subject to change without notice. Printed in Germany
EN0B-0638GE51 R1009
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.