Honeywell 7580G-5USBX-0 User Manual

Genesis 7580g

Presentation Area Imager

User’s Guide

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selection and use of software and/or hardware to achieve intended results.

This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII.

 2010-2014 Honeywell International Inc. All rights reserved. Web Address: www.honeywellaidc.com Microsoft® Windows®, Windows NT®, Windows 2000, Windows ME, Windows XP, and the Windows logo are trademarks or

registered trademarks of Microsoft Corporation. Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies

and are the property of their respective owners.

Product Agency Compliance

USA

FCC Part 15 Subpart B Class B

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio or television technician for help. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions.

The user may find the following booklet helpful: “Something About Interference.” This is available at FCC local regional offices. Honeywell is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Honeywell. The correction is the responsibility of the user.

Use only shielded data cables with this system. This unit has been tested with cables less than 3 meters. Cables greater than 3 meters may not meet class B performance.

Caution: Any changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC authorization to operate this equipment.

UL Statement

UL listed: UL60950-1, 2nd Edition.

Canada

Industry Canada ICES-003

This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Conformité à la règlementation canadienne

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada. Son fonctionnement est assujetti aux conditions suivantes :

1. Cet appareil ne doit pas causer de brouillage préjudiciable.

2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le brouillage pouvant causer un fonctionnement indésirable.

C-UL Statement

C-UL listed: CSA C22.2 No.60950-1-07, 2nd Edition.

Europe

The CE marking indicates compliance to 2004/108/EC EMC Directive with Standards EN55022 CLASS B, EN55024, EN61000-3-2, EN61000-3-3 and 2011/65/EU RoHS directive. In addition, complies to 2006/95/EC Low Voltage Directive, when shipped with recommended power supply. European contact:

Hand Held Products Europe B.V. Nijverheidsweg 9-13 5627 BT Eindhoven The Netherlands

Honeywell International Inc. shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.

Honeywell Scanning & Mobility Product Environmental Information

Refer to www.honeywellaidc.com/environmental for the RoHS / REACH / WEEE information.

Australia/NZ

C-Tick Statement

Conforms to AS/NZS 3548 EMC requirement

Taiwan

If the following label is attached to your product, the product meets Taiwan agency approval:

BSMI Standard: CNS13438, CNS14336-1 依據標準 : CNS13438, CNS14336-1

International

LED Safety Statement

LEDs have been tested and classified as “EXEMPT RISK GROUP” to the standard: IEC 62471:2006.

CB Scheme

Certified to CB Scheme IEC 60950-1, Second Edition.

Patents

For patent information, please refer to www.hsmpats.com.

Warning

To reduce the possibility of heat-related injuries, avoid touching sections of the scanner that feel warm.

Required Safety Labels

Compliance Label location

Part Number, Serial Number and Revision Information location

Illumination output

Chapter 1 - Getting Started

About This Manual ...............................................................................................................1-1

Unpacking Your Device .......................................................................................................1-1

Connecting the Device.........................................................................................................1-1

Connecting with USB .....................................................................................................1-1

Connecting with Keyboard Wedge.................................................................................1-1

Connecting with RS232 Serial Port................................................................................1-2

Connecting with RS485..................................................................................................1-3

Connecting with EAS .....................................................................................................1-3

Reading Techniques ............................................................................................................1-5

Menu Bar Code Security Settings........................................................................................1-5

Setting Custom Defaults ......................................................................................................1-6

Resetting the Custom Defaults ............................................................................................1-6

Chapter 2 - Programming the Interface

Introduction ..........................................................................................................................2-1

Programming the Interface - Plug and Play .........................................................................2-1

Keyboard Wedge .................................................................................................................2-1

Laptop Direct Connect .........................................................................................................2-1

RS232 Serial Port ................................................................................................................2-1

RS485 ..................................................................................................................................2-2

RS485 Packet Mode ......................................................................................................2-2

USB IBM SurePos ...............................................................................................................2-3

USB PC or Macintosh Keyboard..........................................................................................2-3

USB HID ..............................................................................................................................2-4

USB Serial ...........................................................................................................................2-4

CTS/RTS Emulation.......................................................................................................2-4

ACK/NAK Mode .............................................................................................................2-4

Remote MasterMind™ for USB ...........................................................................................2-4

Verifone Gilbarco

Honeywell Bioptic Aux Port Configuration ...........................................................................2-5

Datalogic™ Magellan

NCR Bioptic Aux Port Configuration ....................................................................................2-6

Wincor Nixdorf Terminal Default Settings ............................................................................2-6

Wincor Nixdorf Beetle™ Terminal Default Settings .............................................................2-6

Keyboard Country Layout ....................................................................................................2-7

Keyboard Style...................................................................................................................2-14

Keyboard Conversion ........................................................................................................2-15

Control Character Output...................................................................................................2-16

Keyboard Modifiers ............................................................................................................2-16

Ruby Terminal Default Settings...........................................................................2-5

Terminal Default Settings ....................................................................................2-5

Aux Port Configuration....................................................................2-6

RS232 Modifiers ................................................................................................................2-18

RS232 Baud Rate........................................................................................................ 2-18

RS232 Word Length: Data Bits, Stop Bits, and Parity.................................................2-19

RS232 Receiver Time-Out...........................................................................................2-20

RS232 Handshaking....................................................................................................2-20

RS232 Timeout............................................................................................................ 2-20

XON/XOFF ..................................................................................................................2-21

ACK/NAK.....................................................................................................................2-21

Scanner to Bioptic Communication ................................................................................... 2-21

Scanner-Bioptic Packet Mode .....................................................................................2-21

Scanner-Bioptic ACK/NAK Mode.................................................................................2-22

Scanner-Bioptic ACK/NAK Timeout.............................................................................2-22

Chapter 3 - Input/Output Settings

Power Up Beeper ................................................................................................................ 3-1

Beep on BEL Character.......................................................................................................3-1

Trigger Click ........................................................................................................................3-1

Good Read and Error Indicators..........................................................................................3-2

Beeper – Good Read.....................................................................................................3-2

Beeper Volume – Good Read........................................................................................3-2

Beeper Pitch – Good Read............................................................................................ 3-2

Beeper Pitch – Error ......................................................................................................3-3

Beeper Duration – Good Read ......................................................................................3-3

LED – Good Read .........................................................................................................3-3

Number of Beeps – Good Read ....................................................................................3-4

Number of Beeps – Error............................................................................................... 3-4

Good Read Delay ..........................................................................................................3-4

User-Specified Good Read Delay..................................................................................3-4

Manual Trigger Modes.........................................................................................................3-5

LED Illumination - Manual Trigger .................................................................................3-5

Serial Trigger Mode.............................................................................................................3-5

Read Time-Out ..............................................................................................................3-6

Presentation Mode ..............................................................................................................3-6

LED Illumination - Presentation Mode ...........................................................................3-6

Presentation LED Behavior after Decode......................................................................3-7

Presentation Sensitivity .................................................................................................3-7

Presentation Centering.................................................................................................. 3-7

CodeGate

Streaming Presentation™ Mode .........................................................................................3-9

Mobile Phone Read Mode.................................................................................................3-10

Hands Free Time-Out........................................................................................................3-10

Reread Delay.....................................................................................................................3-10

User-Specified Reread Delay ............................................................................................3-11

Illumination Lights..............................................................................................................3-11

Aimer Delay .......................................................................................................................3-11

User-Specified Aimer Delay.........................................................................................3-12

Aimer Mode ....................................................................................................................... 3-12

Presentation Aimer Mode ..................................................................................................3-12

..........................................................................................................................3-9

Enhanced Object Detection...............................................................................................3-12

Centering...........................................................................................................................3-13

Preferred Symbology.........................................................................................................3-14

High Priority Symbology ..............................................................................................3-15

Low Priority Symbology ...............................................................................................3-15

Preferred Symbology Time-out.................................................................................... 3-15

Preferred Symbology Default.......................................................................................3-15

Output Sequence Overview...............................................................................................3-15

Require Output Sequence ...........................................................................................3-15

Output Sequence Editor ..............................................................................................3-16

To Add an Output Sequence .......................................................................................3-16

Other Programming Selections....................................................................................3-16

Output Sequence Editor ..............................................................................................3-17

Partial Sequence .........................................................................................................3-17

Require Output Sequence ...........................................................................................3-18

Multiple Symbols ...............................................................................................................3-18

No Read ............................................................................................................................3-19

Video Reverse ...................................................................................................................3-19

Working Orientation...........................................................................................................3-20

Chapter 4 - Data Editing

Prefix/Suffix Overview .........................................................................................................4-1

To Add a Prefix or Suffix:............................................................................................... 4-1

To Clear One or All Prefixes or Suffixes........................................................................ 4-2

To Add a Carriage Return Suffix to All Symbologies..................................................... 4-2

Prefix Selections..................................................................................................................4-2

Suffix Selections..................................................................................................................4-2

Function Code Transmit ...................................................................................................... 4-3

Intercharacter, Interfunction, and Intermessage Delays......................................................4-3

Intercharacter Delay ......................................................................................................4-3

User Specified Intercharacter Delay.............................................................................. 4-3

Interfunction Delay.........................................................................................................4-4

Intermessage Delay....................................................................................................... 4-4

Chapter 5 - Data Formatting

Data Format Editor Introduction .......................................................................................... 5-1

Add a Data Format .............................................................................................................. 5-1

Other Programming Selections......................................................................................5-2

Terminal ID Table................................................................................................................5-3

Data Format Editor Commands...........................................................................................5-3

Move Commands...........................................................................................................5-6

Search Commands........................................................................................................ 5-7

Miscellaneous Commands.............................................................................................5-9

Data Formatter ..................................................................................................................5-11

Data Format Non-Match Error Tone............................................................................ 5-12

Primary/Alternate Data Formats........................................................................................5-12

Single Scan Data Format Change............................................................................... 5-13

iii

Chapter 6 - Symbologies

All Symbologies...................................................................................................................6-1

Message Length Description...............................................................................................6-1

Codabar...............................................................................................................................6-2

Codabar Concatenation................................................................................................. 6-3

Code 39 ............................................................................................................................... 6-4

Code 32 Pharmaceutical (PARAF)................................................................................ 6-5

Full ASCII....................................................................................................................... 6-6

Code 39 Code Page ......................................................................................................6-6

Interleaved 2 of 5.................................................................................................................6-7

NEC 2 of 5........................................................................................................................... 6-8

Code 93 ............................................................................................................................... 6-9

Code 93 Code Page ....................................................................................................6-10

Straight 2 of 5 Industrial (three-bar start/stop)...................................................................6-11

Straight 2 of 5 IATA (two-bar start/stop)............................................................................6-12

Matrix 2 of 5.......................................................................................................................6-13

Code 11 ............................................................................................................................. 6-14

Code 128........................................................................................................................... 6-15

ISBT 128 Concatenation..............................................................................................6-15

Code 128 Code Page ..................................................................................................6-16

GS1-128 ............................................................................................................................ 6-17

Telepen..............................................................................................................................6-18

UPC-A ...............................................................................................................................6-19

UPC-A/EAN-13 with Extended Coupon Code...................................................................6-21

Coupon GS1 DataBar Output............................................................................................6-21

UPC-E0 .............................................................................................................................6-22

UPC-E1 .............................................................................................................................6-24

EAN/JAN-13 ......................................................................................................................6-24

Convert UPC-A to EAN-13 ..........................................................................................6-24

ISBN Translate ............................................................................................................6-26

EAN/JAN-8 ........................................................................................................................ 6-27

MSI .................................................................................................................................... 6-29

GS1 DataBar Omnidirectional ........................................................................................... 6-31

GS1 DataBar Limited.........................................................................................................6-31

GS1 DataBar Expanded....................................................................................................6-32

Trioptic Code ..................................................................................................................... 6-32

Codablock A ......................................................................................................................6-33

Codablock F ...................................................................................................................... 6-34

PDF417 .............................................................................................................................6-35

MacroPDF417 ................................................................................................................... 6-35

MicroPDF417.....................................................................................................................6-36

GS1 Composite Codes......................................................................................................6-36

UPC/EAN Version........................................................................................................6-37

GS1 Emulation ..................................................................................................................6-37

TCIF Linked Code 39 (TLC39) ..........................................................................................6-38

QR Code............................................................................................................................6-38

QR Code Page ............................................................................................................6-39

Data Matrix ........................................................................................................................ 6-40

Data Matrix Code Page ...............................................................................................6-40

MaxiCode ..........................................................................................................................6-41

Aztec Code ........................................................................................................................6-42

Aztec Code Page.........................................................................................................6-42

Chinese Sensible (Han Xin) Code.....................................................................................6-43

Postal Codes - 2D .............................................................................................................6-44

Single 2D Postal Codes:..............................................................................................6-44

Combination 2D Postal Codes:....................................................................................6-45

Postal Codes - Linear........................................................................................................6-48

China Post (Hong Kong 2 of 5).................................................................................... 6-48

Korea Post...................................................................................................................6-49

Chapter 7 - EAS Settings

EAS Considerations ............................................................................................................7-1

EAS Deactivation................................................................................................................. 7-1

Checkpoint...........................................................................................................................7-2

EAS Controller Settings................................................................................................. 7-2

EAS Controller..................................................................................................................... 7-2

EAS Mode of Operation.......................................................................................................7-2

EAS Interlocked Duration Timeout ................................................................................ 7-3

Chapter 8 - Imaging Commands

Single-Use Basis ................................................................................................................. 8-1

Command Syntax................................................................................................................8-1

Image Snap - IMGSNP........................................................................................................8-1

IMGSNP Modifiers......................................................................................................... 8-1

Image Ship - IMGSHP .........................................................................................................8-3

IMGSHP Modifiers......................................................................................................... 8-4

Intelligent Signature Capture - IMGBOX ...........................................................................8-10

Signature Capture Optimize ........................................................................................8-10

IMGBOX Modifiers.......................................................................................................8-11

Chapter 9 - Interface Keys

Keyboard Function Relationships........................................................................................9-1

Supported Interface Keys ....................................................................................................9-2

Chapter 10 - Utilities

To Add a Test Code I.D. Prefix to All Symbologies...........................................................10-1

Show Decoder Revision ....................................................................................................10-1

Show Scan Driver Revision ...............................................................................................10-1

Show Software Revision.................................................................................................... 10-1

Show Data Format.............................................................................................................10-1

Test Menu..........................................................................................................................10-2

TotalFreedom ....................................................................................................................10-2

Application Plug-Ins (Apps) ...............................................................................................10-2

EZConfig-Scanning Introduction........................................................................................10-3

Installing EZConfig-Scanning from the Web................................................................ 10-3

Resetting the Factory Defaults .......................................................................................... 10-4

Chapter 11 - Serial Programming Commands

Conventions.......................................................................................................................11-1

Menu Command Syntax....................................................................................................11-1

Query Commands .............................................................................................................11-1

Responses................................................................................................................... 11-2

Trigger Commands............................................................................................................11-3

Resetting the Custom Defaults..........................................................................................11-3

Menu Commands .............................................................................................................. 11-3

Chapter 12 - Product Specifications

Genesis 7580g Scanner Product Specifications ............................................................... 12-1

Depth of Field Charts.........................................................................................................12-2

Typical Performance....................................................................................................12-2

Guaranteed Performance ...........................................................................................12-2

Standard Connector Pinouts .............................................................................................12-3

Keyboard Wedge.........................................................................................................12-3

Serial Output................................................................................................................ 12-3

RS485 Output..............................................................................................................12-3

USB .............................................................................................................................12-4

EAS.............................................................................................................................. 12-4

EAS - USB................................................................................................................... 12-4

EAS - Serial Output .....................................................................................................12-4

Chapter 13 - Maintenance

Repairs ..............................................................................................................................13-1

Maintenance......................................................................................................................13-1

Cleaning the Scanner ..................................................................................................13-1

Cleaning the Window................................................................................................... 13-1

Inspecting Cords and Connectors ...............................................................................13-1

Replacing Cables in Corded Scanners.............................................................................. 13-1

Replacing a Genesis Interface Cable .......................................................................... 13-2

Replacing a Genesis EAS Cable................................................................................. 13-2

Troubleshooting a Corded Scanner...................................................................................13-2

Chapter 14 - Customer Support

Technical Assistance.........................................................................................................14-1

Appendix A - Reference Charts

Symbology Charts ...............................................................................................................A-1

Linear Symbologies .......................................................................................................A-1

2D Symbologies.............................................................................................................A-2

Postal Symbologies .......................................................................................................A-2

ASCII Conversion Chart (Code Page 1252)........................................................................A-3

Lower ASCII Reference Table.............................................................................................A-4

ISO 2022/ISO 646 Character Replacements ......................................................................A-7

Unicode Key Maps ............................................................................................................A-10

Sample Symbols

Programming Chart

vii

viii

USB Connection:

Getting Started

About This Manual

This User’s Guide provides installation and programming instructions for the Genesis 7580g area-imaging scanners. Product specifications, dimensions, warranty, and customer support information are also included.

Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide.

An asterisk (*) next to an option indicates the default setting.

Unpacking Your Device

After you open the shipping carton containing the product, take the following steps:

• Check for damage during shipment. Report damage immediately to the carrier who delivered the carton.

• Make sure the items in the carton match your order.

• Save the shipping container for later storage or shipping.

Connecting the Device

Connecting with USB

A scanner can be connected to the USB port of a computer.

1. Connect the appropriate interface cable to the device first, then to the computer.

2. The scanner beeps.

3. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual.

The unit defaults to a USB PC Keyboard. Refer to page 2-3 for other USB terminal settings. For additional USB programming and technical information, refer to “USB Application Note,” available at www.honey-

wellaidc.com.

Connecting with Keyboard Wedge

A scanner can be connected between the keyboard and PC as a “keyboard wedge,” where the scanner provides data output that is similar to keyboard entries. The following is an example of a keyboard wedge connection:

1. Turn off power and disconnect the keyboard cable from the back of the terminal/computer.

1 - 1

2. Connect the appropriate interface cable to the device and to the terminal/computer.

Keyboard Wedge Connection:

RS232 Serial Port Connection:

Note: The power supply must be ordered separately, if needed.

3. Turn the terminal/computer power back on. The scanner beeps.

4. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. The scanner beeps once.

The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard. A carriage return (CR) suffix is added to bar code data.

Connecting with RS232 Serial Port

1. Turn off power to the terminal/computer.

2. Connect the appropriate interface cable to the scanner.

Note: For the scanner to work properly, you must have the correct cable for your type of terminal/computer.

3. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port.

4. Once the scanner has been fully connected, power up the computer.

This interface programs 115,200 baud, 8 data bits, no parity, and 1 stop bit.

1 - 2

Connecting with RS485

RS485 Connection:

A Genesis scanner can be connected for an IBM POS terminal interface.

1. Connect the appropriate interface cable to the device, then to the computer.

2. Turn the terminal/computer power back on. The scanner beeps.

3. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. The scanner beeps once.

For further RS485 settings, refer to RS485, page 2-2.

Connecting with EAS

A Genesis scanner can be connected to a Checkpoint EAS system. Refer to EAS Settings beginning on page 7-1 for configuration codes and further EAS programming information.

1 - 3

USB Interface with EAS

USB with EAS Connection:

Close-up of EAS Connection:

Checkpoint Wires

1. Connect the appropriate interface and EAS cable to the device, and then to the computer.

2. The scanner beeps.

3. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual.

wellaidc.com.

1 - 4

RS232 Interface with EAS

RS232 with EAS Connection:

Close-up of EAS Connection:

Checkpoint Wires

1. Turn off power to the terminal/computer.

2. Connect the appropriate interface and EAS cable to the device, and then to the computer.

Note: For the scanner to work properly, you must have the correct cable for your type of terminal/computer.

3. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port.

4. Once the scanner has been fully connected, power up the computer.

This interface programs 115,200 baud, 8 data bits, no parity, and 1 stop bit.

Reading Techniques

Present the bar code to the scanner. The LEDs turn up to read the code. If the light level in the room is not high enough, the code may not be read.

Menu Bar Code Security Settings

Honeywell scanners are programmed by scanning menu bar codes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings. Please contact the nearest technical support office (see Technical Assistance on page 14-1) for further information.

1 - 5

Setting Custom Defaults

Set Custom Defaults

Save Custom Defaults

Activate Custom Defaults

You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults bar code below before scanning the menu commands for your custom defaults. If a menu command requires scanning numeric codes from the back cover, then a Save code, that entire sequence will be saved to your custom defaults. When you have entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults bar code.

You may have a series of custom settings and want to correct a single setting. To do so, just scan the new setting to overwrite the old one. For example, if you had previously saved the setting for Beeper Volume at Low to your custom defaults, and decide you want the beeper volume set to High, just scan the Set Custom Defaults bar code, then scan the Beeper Volume High menu code, and then Save Custom Defaults. The rest of the custom defaults will remain, but the beeper volume setting will be updated.

Resetting the Custom Defaults

If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below. This is the recommended default bar code for most users. It resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default settings.

1 - 6

IBM PC AT and Compatibles with

CR suffix

Laptop Direct Connect

with CR suffix

RS232 Interface

Programming the Interface

Introduction

This chapter describes how to program your system for the desired interface.

Programming the Interface - Plug and Play

Plug and Play bar codes provide instant scanner set up for commonly used interfaces.

Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.

Keyboard Wedge

If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard, scan the bar code below. Keyboard wedge is the default interface.

Note: The following bar code also programs a carriage return (CR) suffix.

Laptop Direct Connect

For most laptops, scanning the Laptop Direct Connect bar code allows operation of the scanner in parallel with the integral keyboard. The following Laptop Direct Connect bar code also programs a carriage return (CR) suffix and turns on Emulate External Keyboard (page 2-15).

RS232 Serial Port

The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal. The following RS232 Interface bar code also programs a carriage return (CR) and a line feed (LF) suffix, baud rate, and data format as indicated below. It also

changes the trigger mode to manual.

Option Setting

Baud Rate 115,200 bps Data Format 8 data bits, no parity bit, 1 stop bit

2 - 1

RS485

IBM Port 5B Interface

IBM Port 9B

HHBCR-1 Interface

IBM Port 17 Interface

IBM Port 9B

HHBCR-2 Interface

* Packet Mode Off

Packet Mode On

Scan one of the following “Plug and Play” codes to program the scanner for an IBM POS terminal interface.

Note: After scanning one of these codes, you must power cycle the cash register.

Each bar code above also programs the following suffixes for each symbology:

Symbology Suffix Symbology Suffix

EAN 8 0C Code 39 00 0A 0B EAN 13 16 Interleaved 2 of 5 00 0D 0B UPC A 0D Code 128 * 00 0A 0B UPC E 0A Code 128 ** 00 18 0B

Aztec 00 34 0B PDF417 00 2E 0B Data Matrix 00 32 0B QR 00 33 0B

* Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-1, and IBM 4683 Port 17 Interfaces **Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface

RS485 Packet Mode

The following selection allows you to break up large bar code data into smaller packets on an IBM POS terminal. To break up large bar codes into small packets, scan the Packet Mode On bar code below. Scan the Packet Mode Off bar code if you

want large bar code data to be sent to the host in a single chunk. Default = Packet Mode Off.

2 - 2

RS485 Packet Length

Packet Length

USB IBM SurePos

(USB Handheld Scanner)

Interface

USB IBM SurePos

(USB Tabletop Scanner)

Interface

(

)

USB Keyboard (Mac)

USB Japanese Keyboard (PC)

If you are using Packet mode, you can specify the size of the data “packet” that is sent to the host. Scan the Packet Length bar code, then the packet size (from 20 - 256) from the Programming Chart inside the back cover of this manual, then Save. Default = 40.

USB IBM SurePos

Scan one of the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner) interface.

Note: After scanning one of these codes, you must power cycle the cash register.

Each bar code above also programs the following suffixes for each symbology:

Symbology Suffix Symbology Suffix

EAN 8 0C Code 39 00 0A 0B EAN 13 16 Interleaved 2 of 5 00 0D 0B UPC A 0D Code 128 00 18 0B UPC E 0A Code 39 00 0A 0B

USB PC or Macintosh Keyboard

Scan one of the following codes to program the scanner for USB PC Keyboard or USB Macintosh Keyboard. Scanning these codes also adds a CR suffix.

2 - 3

USB HID

USB HID Bar Code Scanner

USB Serial

CTS/RTS Emulation On

* CTS/RTS Emulation Off

ACK/NAK Mode On

* ACK/NAK Mode Off

ReM Off

Scan the following code to program the scanner for USB HID bar code scanners.

USB Serial

Scan the following code to program the scanner to emulate a regular RS232-based COM Port. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com). The driver will use the next available COM Port number. Apple® Macintosh computers recognize the scanner as a USB CDC class device and automatically use a class driver.

Note: No extra configuration (e.g., baud rate) is necessary.

CTS/RTS Emulation

ACK/NAK Mode

Remote MasterMind™ for USB

When using a USB interface, you may wish to configure your scanner to communicate with Remote MasterMind Scanner Management Software (ReM). Scan the ReM On bar code to communicate with ReM. To disable this capability, scan ReM Off.

Default = ReM On.

2 - 4

Verifone® Ruby Terminal Default Settings

ReM On

Verifone Ruby Settings

Gilbarco Settings

Honeywell Bioptic Settings

Scan the following Plug and Play code to program the scanner for a Verifone Ruby terminal. This bar code sets the baud rate to 1200 bps and the data format to 8 data bits, no parity bit, 1 stop bit. It also adds a line feed (LF) suffix and programs the following prefixes for each symbology:

Symbology Prefix

UPC-A A UPC-E A EAN-8 FF EAN-13 F

Gilbarco® Terminal Default Settings

Scan the following Plug and Play code to program the scanner for a Gilbarco terminal. This bar code sets the baud rate to 2400 bps and the data format to 7 data bits, even parity, 2 stop bits. It also adds a carriage return (CR) suffix and programs the following prefixes for each symbology:

Symbology Prefix

UPC-A A UPC-E E0 EAN-8 FF EAN-13 F

Honeywell Bioptic Aux Port Configuration

Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.

2 - 5

Datalogic™ Magellan® Aux Port Configuration

Datalogic Magellan Settings

NCR Bioptic Settings

Wincor Nixdorf Terminal Settings

Scan the following Plug and Play code to program the scanner for a Datalogic Magellan auxiliary port configuration. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit.

NCR Bioptic Aux Port Configuration

Scan the following Plug and Play code to program the scanner for an NCR bioptic scanner auxiliary port configuration. The following prefixes are programmed for each symbology:

Symbology Prefix Symbology Prefix

UPC-A A Interleaved 2 of 5 b UPC-E E0 Code 128 f

GS1 DataBar Omnidirecitonal

EAN-8 FF GS1 DataBar

Expanded EAN-13 F Codabar N Code 39 a Code 32

Pharmaceutical

(PARAF)

Wincor Nixdorf Terminal Default Settings

Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf terminal. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit.

Wincor Nixdorf Beetle™ Terminal Default Settings

Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf Beetle terminal. The following prefixes are programmed for each symbology:

Symbology Prefix Symbology Prefix

Code 128 K EAN-13 A Code 93 L GS1-128 P Codabar N Interleaved 2 of 5 I UPC-A A0 Plessey O UPC-E C Straight 2 of 5 IATA H EAN-8 B All other bar codes M

2 - 6

Keyboard Country Layout

Wincor Nixdorf Beetle Settings

* United States

Albania

Azeri (Cyrillic)

Azeri (Latin)

Belarus

Belgium

Bosnia

Brazil

Brazil (MS)

Scan the appropriate country code below to program the keyboard layout for your country or language. As a general rule, the following characters are supported, but need special care for countries other than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

Keyboard Countries

2 - 7

Keyboard Countries (Continued)

Bulgaria (Cyrillic)

Bulgaria (Latin)

Canada (French legacy)

Canada (French)

Canada (Multilingual)

Croatia

Czech

Czech (Programmers)

Czech (QWERTY)

Czech (QWERTZ)

Denmark

2 - 8

Keyboard Countries (Continued)

Dutch (Netherlands)

Estonia

Faroese

Finland

France

Gaelic

Germany

Greek

Greek (220 Latin)

Greek (220)

Greek (319 Latin)

2 - 9

Keyboard Countries (Continued)

Greek (319)

Greek (Latin)

Greek (MS)

Greek (Polytonic)

Hebrew

Hungarian (101 key)

Hungary

Iceland

Irish

Italian (142)

Italy

2 - 10

+ 172 hidden pages

Honeywell 7580G-5USBX-0 User Manual

Table of Contents

Getting Started

About This Manual

Unpacking Your Device

Connecting the Device

Connecting with USB

Connecting with Keyboard Wedge

Connecting with RS232 Serial Port

Connecting with RS485

Connecting with EAS

Reading Techniques

Menu Bar Code Security Settings

Setting Custom Defaults

Resetting the Custom Defaults

Laptop Direct Connect

Programming the Interface

Introduction

Programming the Interface - Plug and Play

Keyboard Wedge

RS232 Serial Port

RS485

RS485 Packet Mode

USB IBM SurePos

USB PC or Macintosh Keyboard

USB HID

USB Serial

CTS/RTS Emulation

ACK/NAK Mode

Remote MasterMind™ for USB

Verifone® Ruby Terminal Default Settings

Gilbarco® Terminal Default Settings

Honeywell Bioptic Aux Port Configuration

Datalogic™ Magellan® Aux Port Configuration

NCR Bioptic Aux Port Configuration

Wincor Nixdorf Terminal Default Settings

Wincor Nixdorf Beetle™ Terminal Default Settings

Keyboard Country Layout