Honeywell 7300 User Manual
Place Bar Code Here
62-2020-03
Wireless Communication Card for
TB7200/7300/7600 Series
Communicating Thermostats
INSTALLATION INSTRUCTIONS
APPLICATION
The Honeywell wireless communication card (TB-VWG-APP-1014)
and related WirelessStatNetwork.jar driver file are designed for use
with WEBs-AX controllers to integrate Honeywell TB7200, TB7300,
and TB7600 Series wireless thermostats into a WEBs-AX building
control system. This card allows the integrator to work in the familiar
Workbench tool set using any of the TB7200, TB7300, and TB7600
Series wireless thermostats.
The wireless communication card and TB7200, TB7300, and
TB7600 Series thermostats use ZigBee
wireless thermostats are ideal for retrofit applications where the
addition of communicating field bus wiring in the building space is
difficult or cost prohibitive.
This document covers the mounting of the wireless communication
card in a WEBs-AX controller.
BEFORE YOU BEGIN
Included in the wireless card package you should find the following items:
• The wireless communication card
• A local antenna
A #2 phillips screwdriver is required for installation.
To add the Honeywell wireless thermostat network to a WEBs system, you need two .jar files for the WEBStation-AX.
You can download these files from the Honeywell Buildings Forum at buildingsforum.honeywell.com.
.Jar Files Needed:
• Wireless Thermostat Network Driver: WirelessTstat.jar, version 4.0.4.8 or greater.
• Wireless Thermostat Device and Point Configuration: Wireless TstatDevices.jar, version 4.0.4.8 or greater.
®
wireless mesh. The
More Information
We recommend downloading the Honeywell Wireless Installation and Integration Reference Guide for the TB7200,
TB7300, and TB7600 Series Thermostats (Form No. 63-4522) from http://customer.honeywell.com before you begin
installation.
WIRELESS COMMUNICATION CARD FOR TB7200/7300/7600 SERIES COMMUNICATING THERMOSTATS
CAUTION
Fig. 1. Removing battery and bracket assembly
Fig. 2. Antenna location
INSTALLATION
Erratic System Operation Hazard.
Failure to follow proper wiring practices can introduce disruptive electrical interference (noise). Keep wiring at
least one foot away from large inductive loads such as motors line starters, lighting ballasts, and large power
distribution panels.
Shielded cable is required in installations where these guidelines cannot be met.
Ground shield only to grounded controller case.
IMPORTANT
All wiring must comply with local electrical codes and ordinances or as specified on installation wiring diagrams.
• Power to the WEBs-AX controller must be OFF when installing or removing the wireless communication card or
damage will occur! Also, be careful to plug the wireless communication card into its connector properly (pins
aligned).
• Only one the wireless communication card can be installed in a WEBs-AX controller. Always install the card in option
slot 1 in WEB-2xx and WEB-6xx models. Option slot 1 or 2 can be used on WEB-7xx models.
Mounting the wireless communication card on a WEBs-AX controller
1. Remove power from the controller.
2. Remove the controller cover. To do this, press in the four tabs on both ends of the unit, and lift the cover off.
NOTE: If other expansion accessory modules are
plugged into the controller, you may need to
slide them away from the unit to get to the cover
tabs.
3. Remove the battery and bracket assembly by taking out
the four screws. (Fig. 1)
4. Unplug the battery from the connector on the controller.
5. Remove screws and battery assembly.
6. Remove the front blanking end plate for option slot 1
(Com1) on WEB-2xx and WEB-6xx controllers and
option slot 1 or 2 (Com3 or Com4 in the WEBStation-AX)
on WEB-7xx controllers.
7. Carefully insert the pins of the wireless communication
card into the appropriate socket. The mounting holes on
the option board should line up with the standoffs on the
base board. If they do not, the connector is not properly
aligned. Press until the option card is completely seated.
8. Plug the battery cable back into the battery connector on
the controller
9. Set the battery and bracket assembly back over the
option card slots, with the mounting holes aligned with
the standoffs.
10. Re-fasten screws through battery bracket the four holding screws through. DO NOT over tighten.
11. Replace the controller cover.
12. Install the antenna. (Fig. 2)
BATTERY
ASSEMBLY
(INCLUDES
CABLE AND
BRACKET)
BLANKING
END PLATE
SCREWS (4)
OPTION
SLOT 1
AREA
UNPLUG
BATTERY HERE
OPTION
SLOT 2
AREA
WEB/
CP-201/
600/
700
M32538
62-2020—03 2
Loading...