Honeywell 1911i User Manual

Granit 1911i

Industrial Wireless Area-Imaging Scanner

Quick Start Guide

Crdlss-GRNT-QS Rev A

8/12

Aller à www.honeywellaidc.com pour le français.
Vai a www.honeywellaidc.com per l'italiano.
Gehe zu www.honeywellaidc.com für Deutsch.
Ir a www.honeywellaidc.com para español.
Para Português, acesse www.honeywellaidc.com.br.

Перейти на русскоязычный сайт www.honeywellaidc.com.

Pro češtinu jdi na www.honeywellaidc.com.
Pre slovenčinu choď na www.honeywellaidc.com

日本語 : www.honeywellaidc.com をご覧ください。
如要到中国 www.honeywellaidc.com（简体）。

查看繁体版请登陆 www.honeywellaidc.com

한글 www.honeywellaidc.com 로 이동합니다 .

Note: Refer to your user’s guide for information about cleaning your

device.

For localized language versions of this document, go to

www.honeywellaidc.com.

Getting Started

Turn off the computer’s power before connecting the base, then
power up the computer once the base is fully connected. When the
base is connected and powered up, put the scanner in the base to
establish a link. The green LED on the base flashes to indicate the
scanner’s battery is charging.

Power Supply Assembly (if included)

Note: The power supply must be ordered separately, if needed.

Connecting the Base
USB:

Keyboard Wedge:

RS232 Serial Port:

Reading Techniques

Standard Product Defaults

The view finder projects an aiming
beam that should be centered over
the bar code, but it can be
positioned in any direction for a
good read.

Hold the scanner over the bar code,
pull the trigger, and center the
aiming beam on the bar code.

The aiming beam is smaller when
the scanner is closer to the code
and larger when it is farther from the
code. Hold the scanner close to
smaller bar codes, and farther away
from large bar codes to get a proper
read.

If the bar code is highly reflective (e.g., laminated), you may need to
tilt the scanner at an angle so the bar code can be scanned.

Note: If the scanner beeps 3 times when scanning a bar code, the

link has not been established. If the scanner beeps once, the
link has been established.

Standard Product Defaults

The following bar code resets all standard product default settings.

USB Serial

USB Serial

USB PC Keyboard

Scan the following code to program the scanner to emulate a regular
RS232-based COM Port. If you are using a Microsoft® Windows®
PC, you will need to download a driver from the Honeywell website

(www.honeywellaidc.com). The driver will use the next available

COM Port number. Apple® Macintosh computers recognize the
scanner as a USB CDC class device and automatically use a class
driver.

Note: No extra configuration (e.g., baud rate) is necessary.

USB PC Keyboard

Scan the following code to program the scanner for a USB PC
Keyboard.

Keyboard Country

Program Keyboard Country

Save

Scan the Program Keyboard Country bar code below, then scan
the numeric bar code(s) from page 2, then the Save bar code to
program the keyboard for your country. As a general rule, the
following characters are not supported by the scanner for countries
other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~.

Country Code Scan Country Code Scan

Belgium 1 Italy 5
Denmark 8 Norway 9
Finland 2 Spain 10
France 3 Switzerland 6
Germany/Austria 4 USA (Default) 0
Great Britain 7

Note: For a complete list of country codes, see the User’s Guide for

your product at our website,

www.honeywellaidc.com.

Locked Link

Locked Link Mode

(Single Scanner)

Override Locked Scanner

Unlink Scanner

If you link a scanner to a base using the Locked Link Mode, other
scanners are blocked from being linked if they are inadvertently
placed into the base. If you do place a different scanner into the
base, it will charge the scanner, but the scanner will not be linked.

To use a different scanner, you need to unlink the original scanner by
scanning the Unlink Scanner bar code.

Override Locked Scanner

If you need to replace a broken or lost scanner that is linked to a
base, scan the Override Locked Scanner bar code with a new
scanner, and place that scanner in the base. The locked link will be
overridden; the broken or lost scanner’s link with the base will be
removed, and the new scanner will be linked.

Unlinking the Scanner

If the base has a scanner linked to it, that scanner must be unlinked
before a new scanner can be linked. Once the previous scanner is
unlinked, it will no longer communicate with the base. Scan the

Unlink Scanner bar code to unlink a scanner.

Trigger

Manual Trigger - Normal

(Default)

Presentation Mode

Streaming Presentation Mode

The following bar codes will allow you to use the scanner in Manual
Trigger - Normal Mode (need to press the trigger to read) or
Presentation mode (the scanner is activated when it “sees” a bar
code).

Streaming Presentation™

When in Streaming Presentation mode, the scanner leaves the scan
illumination on all the time and continuously searches for bar codes.

Suffix

Add CR Suffix

Remove Suffix

Add Tab Suffix

Add Code ID Prefix To All Symbologies

(Temporary)

If you want a carriage return after the bar code, scan the Add CR

Suffix bar code. To add a tab after the bar code, scan the Add Tab
Suffix bar code. Otherwise, scan the Remove Suffix bar code to

remove the suffixes.

Add Code ID Prefix to all Symbologies

Scan the following bar code if you wish to add a Code ID prefix to all
symbologies at once.

Note: For a complete list of Code IDs, see the User’s Guide for your

product at our website,

www.honeywellaidc.com.

Function Code Transmit

Enable

(Default)

Disable

When this selection is enabled and function codes are contained
within the scanned data, the scanner transmits the function code to
the terminal. Charts of these function codes are provided in your
User’s Guide. When the scanner is in keyboard wedge mode, the
scan code is converted to a key code before it is transmitted.

Data Format Editor Instructions

Enter Data Format

Clear All Data Formats

Save

The following are abbreviated instructions for entering a data format.
For complete instructions refer to your User’s Guide, available at our
website,

1. Scan the Enter Data Format symbol.

2. Primary/Alternate Format: scan 0 for Primary Format

3. Terminal Type: scan 099 for any terminal type

4. Code I.D.: scan 99 for any bar code type

5. Length: scan 9999 for any length bar code.

6. Editor commands: use the Programming Chart that follows.

7. Scan Save to save your entries.

www.honeywellaidc.com.

Programming Chart

0

2

1

4

3

5

6

7

A

B

C

D

E

F

9

8

Save

EZConfig-Scanning

To access additional features for the scanner use EZConfig­Scanning, an online configuration software tool, available from our
website at

www.honeywellaidc.com.

Technical Assistance

Contact information for technical support, product service, and repair
can be found at

www.honeywellaidc.com.

Limited Warranty

Refer to www.honeywellaidc.com/warranty_information for your
product’s warranty information.

Patents

For patent information, refer to www.honeywellaidc.com/patents.

User Documentation

For localized versions of this document, and to download the User’s
Guide, go to

www.honeywellaidc.com.

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in
specifications and other information contained in this document without prior
notice, and the reader should in all cases consult HII to determine whether
any such changes have been made. The information in this publication does
not represent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from the
furnishing, performance, or use of this material.

This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated into another language without the prior written
consent of HII.

© 2012 Honeywell International Inc. All rights reserved.

Web Address: www.honeywellaidc.com