Honda Civic Hatchback (2023) Navigation Manual

Navigation Manual

2023 CIVIC

The information and specifications included in this publication were in effect at the time of approval for printing. Honda Motor Co., Ltd., reserves the right,

NOTICE

WARNING

however, to discontinue or change specifications or design at any time without notice and without incurring any obligation.

Accessories Precautions

The GPS antenna is located in the dashboard. Metallic front or side window tinting can seriously degrade or obstruct GPS reception.

Signal noise from devices such as radar detectors, vehicle tracking devices, remote starters, and additional amplifiers can disrupt the navigation system. If you install any such item, install it away from the navigation display and antenna.

Important Safety Information

Using the navigation system while driving can take your attention away from the road, causing a crash in which you could be seriously injured or killed.

Only operate system controls when the conditions permit you to safely do so.

Avoid focusing on the screen or manually operating the system controls while driving.

Certain on-screen controls are disabled when driving, however most of the voice commands continue to function. Pull to the side of the road if you need to devote more attention and time to look at the screen or access additional menus.

Route guidance may conflict with street closures, road construction, detours, and out-of-date map data.

The system itself may also have limitations. Verify route information by carefully observing roads, signs, and signals. Always use your own judgment and obey traffic laws.

System Limitations

Upon removing this vehicle’s navigation display, please reuse, recycle, or dispose of as hazardous waste.

Clean the screen with a soft, damp cloth. You may use a mild cleaner intended for use on navigation screens.

P. 102

2 System Setup P. 17

Start-up 18 Voice Control System 19 Personal Information 20 Display Mode Settings 27 Guidance Volume Settings 29 Main Menu 30 Map Options 31 Route Options 38 Guidance Options 43 Tutorial 49 Manage Places 50 Map Update 56 Settings 57 Data Reset 60

Quick Reference Guide

System Setup

P. 2

P. 17

2 Navigation P. 61

Entering a Destination 62 Calculating the Route 78 Driving to Your Destination 81 Map Operation 85 Changing Your Route 89 Changing Your Destination 92

2 Troubleshooting P. 95

Troubleshooting 96

2 Reference Information P. 101

System Limitations 102 Customer Assistance 104 Legal Information 106

2 Voice Commands P. 111

Voice Commands 112 List of Categories 114

Navigation

Troubleshooting

Reference Information

Voice Commands

Index

P. 61

P. 95

P. 101

P. 111

P. 115

Quick Reference Guide

Store home address

(P20)

home address.

Track route

(P81)

Follow your route in real-time with voice guidance.

Store contacts

(P23)

Store locations to use as the destination.

Enter destination

(P62)

Select your destination using several methods.

Select route

(P79)

Set route preferences and select one of the available routes.

Avoid certain areas

(P51)

Set streets and areas to detour around.

Add waypoints

(P90)

Add “pit stops” along your route.

Traffic Information*

(P87)

View and avoid congestion and traffic incidents.

*: Available only in certain areas.

Overview—Functions at a Glance

Navigation

You can select any place/landmark as a destination by using the touchscreen. The navigation system gives you turn-by-turn driving directions to your destination.

Quick Reference Guide

HOME Screen

(Home)

Display the HOME screen.

(Back) Go back to the previous screen. VOL (Volume) Increase or decrease the audio volume.

Navigation

Display the navigation feature that was used the last time. At start-up, the map screen is displayed.

Display Mode ()

Adjust screen brightness or turn off the screen.

The system displays various functions from the HOME screen. Press the button at any time to return to the main HOME screen.

Quick Reference Guide

Touchscreen Operation

You can operate the system using your finger on the touchscreen. The touchscreen can be operated if you are wearing thin gloves, but it may be more difficult for the system to respond.

Tap

Touch the screen lightly with your finger to select an option on the screen.

Long Tap

Touch and hold the screen with your fingertip until you release your finger from the screen to scroll map toward your fingertip.

Swipe

Lightly sweep your finger side to side or up and down to scroll a list or map.

You can change the touchscreen sensitivity setting.

2 Refer to the Owner’s Manual.

Flick

Flick with your finger to scroll the map according to the movement of your finger.

Quick Reference Guide

Zoom In Zoom Out

Twice

Slide

Move your finger slowly across the screen to scroll the map.

Zoom In/Out

Open or close your fingers on the screen in a pinching motion to zoom in or out of the map.

Alternately, you can touch the screen twice with one finger to zoom in, or once with two fingers to zoom out.

Quick Reference Guide

How to Enter Information

On input search screens, the suggested search terms are displayed. Select to display a list of possible entries.

You can remove all entered characters when you press and hold the search bar then select .

You can enter information (e.g., city names, street names, numbers, and symbols) when prompted on the input screen.

Using Voice Commands

When you see in this manual, voice commands are available for that feature.

The system recognizes certain commands. Available navigation voice commands (P112)

 Press the button, and say the letter, number, or symbol (e.g.,

say “1”).

On list screens:

 Say the number of the list item (e.g., say “Three” to select

item 3).

 Say “Back” to return to the previous screen.

 Say “Cancel” to end the voice command function.

 Say “Next” for next page.

 Say “Previous” for previous page.

Using the Touchscreen

Select a character or icon on the screen to select it.

 Select to remove the last entered character.

 Select to display upper/lower case characters.

 Select to enter a space character.

 Select to display other types of characters.

 Select to change the keypad language.

 Select to entered character.

Quick Reference Guide

213th t

Map orientation icon (P85)

Map scale

(P85)

Current location icon

Select to return to the current location.

Searching specific category

(P62)

Current vehicle position Streets Main menu

(P30)

Traffic information

(P87)

Landmark icons

Traffic icons

Day Mode Night Mode

Map Screen Legend

The color of the map is different depending on the selected Map Theme.

Day or Night Mode

The screen switches to Day or Night mode automatically.

(P34)

Quick Reference Guide

During Route Guidance

Next guidance indicator

Select to hear voice guidance.

Next street name

Lane guidance

Destination

Cancel route

Calculated route

Current street name Mute voice guidance

Select again to switch the voice guidance to on.

Distance to destination (waypoint)

Distance of the actual route

Arrival time (waypoint)

Next turn-by-turn instructionsNext turn-by-turn detail

Remaining distance

Next driving maneuver is ap

proaching.

During route guidance, route information is displayed on the map screen. You can see the detailed information on the turn information screen.

Map Screen

Optional Information

(P82, 83)

Turn-by-Turn Directions

The next guidance point appears on the Driver Information Interface.

Quick Reference Guide

Navigation—Home Addresses and Going Home

The “Home” feature automatically routes you to your home address from any location simply by selecting Go Home. You can store one home address. (P20) The order of the steps may change depending on the map data loaded on your system.

Storing Your Home Address

a Select Navigation. b Select .

c Select Go Home and then select Yes.

d Select Name and then enter a name.

e Select Address Search and then select

desired search method.

f Enter your home address. g Select Save when a desired location is

displayed.

h Select Phone No. and then enter a

phone number.

i Select Save.

Going Home

a Select Navigation. b Select .

c Select Go Home.

Alternatively, you can say “Navigation” and then “Go Home” from any screen.

Quick Reference Guide

Navigation—Entering a Destination

Enter your destination using one of several methods, then follow route guidance on the map to your destination. The order of the steps may change depending on the map data loaded on your system.

a Select Navigation. b Select .

c Enter the keyword or address. d Select .

e Select an address from the list.

f Select Go.

Route guidance to the destination begins.

 Save: Save the selected location to the

Saved Places.

 Routes: Choose one of multiple routes.

 : Display your destination map and

save a place.

Quick Reference Guide

Navigation—Changing Route or Destination

You can alter your route by adding waypoints to visit, or changing your destination during route guidance.

Adding a Waypoint (“Pit Stop”)

You can add waypoints along your route.

(P90)

a Select Navigation. b Select . c Select a search method. d Select the location to add to the

destination list and select Go.

e Select Waypoint.

f If necessary, edit the order of the

destinations and select Save.

Changing Your Destination

There are several methods you can use to specify a new destination during route guidance.

 Selecting an icon on the map (P92)

Select a place/landmark icon or a new area on the map.

 Entering a new destination (P93)

Select and then enter a new destination.

Canceling Your Route

a Select .

Alternatively, you can say “Navigation” and then “Stop route” from any screen.

Quick Reference Guide

Voice Control Operation

Voice Portal Screen

a Press and release the button.

The system prompts you to say a voice command. Press and release the button again to bypass this prompt.

 The system beeps when ready for a

command.

 Press the button or say “Cancel”

to cancel.

b Say “Navigation.”

The Voice Command screen is displayed.

After that, follow the voice prompt and say a voice command.

 The audio system is muted during voice

control mode.

 You can use other voice commands on

the Voice Portal screen.

 Carefully read the usage note for the

voice control. Voice Control System (P19)

 The system recognizes certain

commands. Available navigation commands

(P112)

Voice Command Screen

a After saying “Navigation” from

the Voice Portal screen, the below screen appears.

b Listen for the voice prompt, then say a

voice command.

 You do not need to press the

button again in the Voice Command screen.

 Available voice commands are

highlighted on the screen.

Quick Reference Guide

Troubleshooting

For more Information

(P95)

Why does the vehicle position icon on the map appear slightly off my actual position, especially at intersections?

This is normal. The navigation system is unaware of the width of intersections. Large differences in vehicle position can indicate a temporary loss of the GPS signal.

Why does the “Arrival time” display sometimes increase even though I am getting closer to my destination?

The “Arrival time” is based on the speed limit on each road. Depending on the traffic conditions, the “Arrival time” may be calculated to be earlier or later.

Why does my clock frequently change the time forward and backward by one hour?

The clock setting is automatically updated based on your GPS location. If you are driving near a time zone border, the automatic update likely is the reason.

How do I turn on the navigation system voice guidance?

●

Adjust the volume using the volume knob during the voice guidance.

●

Press the (Home) button. Select General Settings > System > System Volumes.

Turn up volume level of Navigation Guidance if it is low.

How do I specify a destination when an entered city or street could not be found?

Try selecting the destination directly from the map.

How to Use This Manual

Searching the Table of Contents

(P1)

First, find the general chapter related to what you are looking for (e.g., entering a destination from the Saved Places). Then, go to that chapter to view a more specific table of contents.

Searching the Index

(P115)

This more detailed table of contents shows you exactly what information is listed by section and title.

The Index consists of main terms and subentries. The sub-entries help you get to the desired page depending on what you are looking for.

Table of Contents

Chapter Contents

Navigation Screen

Index

Two types of Tables of Contents help you find your desired information.

Menu items displayed on the navigation screen (e.g., Saved Places) can be found individually in the Index.

More Detailed

Contents

* Sample pages and images in this section may differ from the actual ones.

This section explains different methods on how you can easily find information in this manual.

Select the item on the system control panel.

Menu Tree

The menu tree helps guide you

through the system’s menu options.

To get to your desired function, follow

the menu tree in order of the steps

shown.

Select the menu option.

After following the menu tree, step-by-step instructions explain how to achieve the desired result.

Select Saved Places.

Saved PlacesNavigation

This page intentionally left blank.

System Setup

This section describes the start-up procedure and the navigation and setup functions.

Start-up ................................................... 18

Voice Control System ............................. 19

Voice Recognition .................................. 19

Personal Information.............................. 20

Setting Home Location........................... 20

Saved Places........................................... 23

Display Mode Settings ........................... 27

Adjusting Screen Brightness ................... 27

Switching Display Mode......................... 28

Guidance Volume Settings..................... 29

Main Menu .............................................. 30

Map Options ........................................... 31

Traffic Icons ........................................... 32

Traffic Flow............................................ 33

Color Theme .......................................... 34

Points of Interest.....................................34

Breadcrumb Trail.....................................35

Breadcrumb Recording............................36

Delete Breadcrumb Trail ..........................36

Landmark Settings ..................................37

Route Options..........................................38

Route Demo ...........................................39

Route Preferences ...................................40

Traffic Rerouting .....................................41

Route Calculation Method ......................42

Guidance Options ....................................43

Estimated Arrival.....................................44

Predictive Routing ...................................45

Delete Learning History ...........................46

Auto Zoom .............................................46

Maneuver Assist Popup .......................... 47

Voice Guidance Language...................... 47

Maneuver List ........................................ 48

Tutorial .................................................... 49

Manage Places ........................................ 50

Avoidance Areas .................................... 51

Editing Recent Destinations .................... 55

Editing Downloaded Places .................... 55

Map Update ............................................ 56

Settings.................................................... 57

Adjust Vehicle Position ........................... 58

Online Services....................................... 59

About Software License ......................... 59

Data Reset ............................................... 60

Reset Factory Default Settings ................ 60

System Setup

Start-up

1 Start-up

Avoid focusing on the screen and drive safely following the actual traffic restrictions.

When you use the navigation system, the system may close other apps.

When you select Navigation, the system displays the navigation feature that was used the last time. At start-up, the map screen is displayed.

Navigation tutorial is displayed at initial start. You can display the tutorial from the main menu at any time.

2 Tutorial P. 49

The navigation system starts automatically when you set the power mode to ACCESSORY or ON. At start-up, the following confirmation screen is displayed.

1. Select OK.

u The Bluetooth connection

message is displayed if you disconnected a Bluetooth device on the HOME screen.

u If you do not select OK, the

system will automatically select OK after a certain period of time.

u The system will automatically

start up the feature that was used the last time.

2. Select Navigation.

u The map screen or navigation

tutorial screen is displayed. If the navigation tutorial screen is displayed, select Exit.

u When you want to display the

navigation top screen, you press the button.

Limitations for Manual Operation

■

Certain manual functions are disabled or inoperable while the vehicle is in motion. You cannot select a grayed-out option until the vehicle is stopped. Voice commands are still operable while the vehicle is in motion.

System Setup

Voice Control System

1 Voice Control System

When you press the button, the system prompts you to say a voice command. Press and release the

button again to bypass this prompt and give a

command.

1 Voice Recognition

The voice control system can only be used from the driver’s seat because the microphone unit removes noises from the passenger’s side.

Your vehicle has a voice control system that allows hands-free operation of the navigation system functions. The voice control system uses the button on the steering wheel and a microphone near the map lights on the ceiling. For details of the button and microphone position, see the Owner’s Manual.

Voice Recognition

To achieve optimum voice recognition when using the navigation voice control system:

• Make sure the correct screen is displayed for the voice command that you are using. The system recognizes certain commands. Available navigation commands:

2 Navigation Commands P. 112

• Close the windows and moonroof.

• Adjust the dashboard and side vents so air does not blow onto the microphone on the ceiling.

• Speak in a clear, natural speaking voice without pausing between words.

• Reduce any background noise if possible. The system may misinterpret your command if more than one person is speaking at the same time.

System Setup

Personal Information

1 Personal Information

The home location can be overwritten. Select Manage Places and then select Home.

2 Manage Places P. 50

Edit Home: Name: Enter the preferred name. Phone No.: Enter the preferred phone number.

Setting Home Location

H u Navigation u

Use the personal information menu to set your home location.

1. Select Go Home and then select Yes.

2. Select Address then select an option.

u Select Select from Map to set

home location.

u If selecting other than Select

from Map, proceed to steps 3

and 4.

3. Select the home location.

4. Select Save and then select Save.

System Setup

The following options are available:

• Select from Map: Sets your current location as your home location.

• Keyword Search: Sets the home location by entering a keyword or address.

• Category Search: Sets the home location by selecting a category.

• Address Search: Sets the home location by entering the address.

• Search Along Route: Sets the home location by along route.

• Saved Places: Sets the home location by selecting a place stored in the Saved

• Phone Number Search: Sets the home location by phone number.

• Coordinates Search: Sets the home location by entering coordinates.

• Recent: Sets the home location from a recently found location.

• Downloaded Places: Sets the home location by downloaded places.

uuPersonal Information u Setting Home Location

2 Storing Your Home Address P. 9

Places list.

Continued

uuPersonal Information u Setting Home Location

System Setup

Editing Home Location

■

H u Navigation uuManage Places u Home

The following options are available:

• Name: Enters a new name for the location.

• Address: Enters a new location.

• Phone No.: Enters a new phone number.

1. Select an item to edit.

2. Select Save.

System Setup

Saved Places

You can save locations so you can quickly find them and create routes to them.

■

H u Navigation u

uuPersonal Information uSaved Places

Saving a Saved Location

1. Select a search method.

u Find a location that you want to

save.

2 Entering a Destination P. 62

2. Select Save.

3. Select Save.

u If necessary, enter a name and

phone number.

u If desired, select a POI icon.

Continued

uuPersonal Information u Saved Places

System Setup

Saving a Saved Location Manually

■

H u Navigation

1. Select a destination from the map.

2 Map Input P. 77

2. Select Save.

3. Select Save.

u If necessary, enter a name and

phone number.

u If desired, select a POI icon.

System Setup

Editing a Saved Location

1 Editing a Saved Location

You can add a new saved location by selecting .

■

H u Navigation uuManage Places u Saved Places

The following options are available:

• Name: Enters a new name for the location.

• Address: Enters a new location.

• Phone No.: Enters a phone number.

• Icon: Select a preferred icon.

uuPersonal Information uSaved Places

1. Select a saved location you want to edit.

2. Select an option.

3. Select Save to edit.

Continued

uuPersonal Information u Saved Places

System Setup

Deleting a Saved Location

■

H u Navigation uuManage Places u Saved Places

Deleting All Saved Locations

■

H u Navigation uuManage Places u Saved Places

1. Select .

u The selected location

2. Select Save.

Select and then select Yes.

disappears from the list.

System Setup

Display Mode Settings

1 Adjusting Screen Brightness

You can also adjust the display brightness by sliding or swiping on the Brightness bar.

You can change the touchscreen sensitivity setting.

2 Refer to the Owner’s Manual.

You can change the color of the map.

2 Color Theme P. 34

Adjusting Screen Brightness

Set the screen brightness. Select Display Mode ( ) to change the screen brightness.

Select Display Mode on the bottom of the screen.

u The Brightness bar is displayed for

a few seconds.

u Select or to adjust the

brightness.

u Select Display OFF to turn off the

screen. To turn on the screen, press the or button.

uuDisplay Mode SettingsuSwitching Display Mode

System Setup

Switching Display Mode

Illumination control Operation

Display Mode ()Adjusts screen brightness when the user wants to change

Sunlight sensor (see the Owner’s Manual for location)

Dash illumination adjustment dial (see the Owner’s Manual for location)

Headlights (Auto/On/ Off)

the brightness of the display temporarily. Remember: Display Mode ( ) overrides all other display brightness adjustments either set automatically by the sunlight sensor or manually from the System settings screen.

If the sunlight sensor detects daylight and the headlights are turned on, the system automatically overrides the Night display and displays the Day display mode. Remember: If desired, use the Display Mode () to adjust the brightness of the display.

When the headlights are turned on, and you wish to have the Day display mode, adjust the illumination to the full brightness (beeps). Remember: Adjust the dash brightness back to midrange to allow auto switching by sensing the headlights are on or off.

When turned on, the display changes to Night display mode. The previous three controls listed above can “cancel” this function. Remember: Use the Display Mode ( ) to adjust the brightness of the display.

System Setup

Guidance Volume Settings

1 Guidance Volume Settings

You can also adjust the volume by sliding or swiping on the volume bar.

During the voice guidance, you can adjust the guidance volume using the volume knob.

H u General Settings u System u System Volumes

Select or of Navigation Guidance.

System Setup

Main Menu

H u Navigation u

Select an option.

The following options are available:

• Map Options: Sets information to be displayed on the map screen.

2 Map Options P. 31

• Route Options: Sets the route options.

2 Route Options P. 38

• Guidance Options: Sets the preferred route guidance.

2 Guidance Options P. 43

• Tutorial: Displays the navigation tutorial.

2 Tutorial P. 49

• Manage Places: Edits your stored locations and avoidance areas.

2 Manage Places P. 50

• Map Update: Displays the map update options.

2 Map Update P. 56

• Settings: Displays other settings.

2 Settings P. 57 2 Data Reset P. 60

System Setup

H u Navigation uuMap Options

The following options are available:

• Traffic Icons: Sets whether to display a traffic icon on the map.

• Traffic Flow: Sets whether to display a traffic flow on the map.

• Color Theme: Changes the color of the map.

• Points of Interest: Selects the POI icons to display on the map.

• Breadcrumb Trail: Sets whether to display the blue tracking line on the map.

• Breadcrumb Recording: Sets whether to record a tracking line on the all road or

• Delete Breadcrumb Trail: Deletes the tracking line on the map.

• Landmark Settings: Selects whether to display the 3D landmarks on the map.

Map Options

Select an option.

2 Traffic Icons P. 32

2 Traffic Flow P. 33

2 Color Theme P. 34

2 Points of Interest P. 34

2 Breadcrumb Trail P. 35

only off-road.

2 Breadcrumb Recording P. 36

2 Delete Breadcrumb Trail P. 36

2 Landmark Settings P. 37

uuMap Optionsu Traffic Icons

System Setup

Traffic Icons

H u Navigation uuMap Options u Traffic Icons

Sets whether to display a traffic icon on the map.

The following options are available:

• ON (factory default): Displays a traffic icon on the map.

• OFF: Disables the feature.

Select an option.

System Setup

Traffic Flow

H u Navigation uuMap Options u Traffic Flow

uuMap Optionsu Traffic Flow

Sets whether to display a traffic flow on the map.

The following options are available:

• ON (factory default): Displays a traffic flow on the map.

• OFF: Disables the feature.

Select an option.

uuMap Optionsu Color Theme

System Setup

Color Theme

H u Navigation uuMap Options u Color Theme

Changes the color of the map.

The following options are available:

• Auto (factory default): Sets the map color to change according to the lighting.

• Day: Displays the map with day colors.

• Night: Displays the map with night colors.

Select an option.

Points of Interest

H u Navigation uuMap Options u Points of Interest

Selects the POI icons to display on the map.

1. Select an option(s).

2. Select Save.

System Setup

Breadcrumb Trail

H u Navigation uuMap Options u Breadcrumb Trail

uuMap Optionsu Breadcrumb Trail

The navigation system can be set to display tracking lines (“breadcrumbs”) on the map screen.

The following options are available:

• ON (factory default): The system displays the tracking line.

• OFF: Disables the feature.

Select an option.

uuMap Optionsu Breadcrumb Recording

System Setup

1 Breadcrumb Recording

Off-road breadcrumbs can be displayed on the screen.

2 Off-Road Breadcrumbs Display P. 84

Breadcrumb Recording

H u Navigation uuMap Options u Breadcrumb Recording

Sets whether to record a tracking line on the all road or only off-road.

The following options are available:

• ON: The system records the tracking line on the all road.

• Only Off-Road (factory default): The system records the tracking line on the only off-road.

• OFF: Disables the feature.

Select an option.

Delete Breadcrumb Trail

H u Navigation uuMap Options u Delete Breadcrumb Trail

Select OK.

System Setup

Landmark Settings

H u Navigation uuMap Options u Landmark Settings

uuMap Optionsu Landmark Settings

Selects whether to display the 3D landmarks on the map.

The following options are available:

• 3D Landmarks:

• Landmark Texture:

Select an option.

– ON (factory default): Displays the 3D landmark on the map. – OFF: Disables the feature.

– ON (factory default): Displays the landmark texture on the map. – OFF: Disables the feature.

System Setup

Route Options

H u Navigation uuRoute Options

Changes the route settings and show the details of the current route.

The following options are available:

• Detour: Calculates a detour route.

2 Taking a Detour P. 89

• Route Overview: Displays the route overview.

2 Route Overview P. 83

• Route Demo: Shows demonstration for current route guidance.

2 Route Demo P. 39

• Route Preferences: Sets roads passed on the route.

2 Route Preferences P. 40

• Destination List: View detailed information about the current destination and waypoints.

2 Editing a Route P. 91

• Traffic Rerouting: Sets whether to use optimized alternate routes.

2 Traffic Rerouting P. 41

• Route Calculation Method: Sets the route calculation method.

2 Route Calculation Method P. 42

System Setup

Route Demo

H u Navigation uuRoute Options u Route Demo (when en route)

uuRoute Optionsu Route Demo

Shows demonstration for current route guidance.

uuRoute OptionsuRoute Preferences

System Setup

Route Preferences

H u Navigation uuRoute Options u Route Preferences

Sets roads passed on the route.

The following options are available:

• Freeways: Sets whether or not to use freeways.

• Toll Roads: Sets whether or not to use toll roads.

• Ferries: Sets whether or not to use ferries.

• Train Ferries: Sets whether or not to use train ferries.

• Unpaved Roads: Sets whether or not to drive on unpaved roads.

• Tunnels: Sets whether or not to pass through tunnels.

1. Select an option(s).

u Checked items are enabled and

unchecked items are disabled.

2. Select Save.

System Setup

Traffic Rerouting

1 Traffic Rerouting

Traffic rerouting can calculate a faster route based on continuously updated traffic information.

H u Navigation uuRoute Options u Traffic Rerouting

uuRoute Optionsu Traffic Rerouting

Sets the automatic re-routing feature.

The following options are available:

• AUTO: Sets the automatic re-routing feature.

• ON (factory default): Sets the automatic re-routing feature with notification popup.

• OFF: Disables the feature.

Select an option(s).

uuRoute OptionsuRoute Calculation Method

System Setup

Route Calculation Method

H u Navigation uuRoute Options u Route Calculation Method

Select an option(s).

The following options are available:

• Fastest (factory default): Calculates routes that are faster to drive but can be longer in distance.

• Shortest: Calculates routes that are shorter in distance but can take more time to drive.

• Suggested: Calculates routes that are suggested by navigation system.

System Setup

Guidance Options

H u Navigation uuGuidance Options

Changes the route guidance settings.

The following options are available:

• Estimated Arrival: Sets the time format for the estimated arrival to a destination

• Predictive Routing: Sets whether to use the predictive route feature.

• Delete Learning History: Deletes the learned route history.

• Auto Zoom: Sets whether the map zooms in automatically according to the

• Maneuver Assist Popup: Sets whether to display the enlarged popup at the

• Voice Guidance Language: Sets the language for voice prompts.

• Maneuver List: Sets whether to display the turn-by-turn instructions on the map.

Select an option.

which is displayed on the guidance screen.

2 Estimated Arrival P. 44

2 Predictive Routing P. 45

2 Delete Learning History P. 46

distance of the next guidance point.

2 Auto Zoom P. 46

intersection is approaching.

2 Maneuver Assist Popup P. 47

2 Voice Guidance Language P. 47

2 Maneuver List P. 48

uuGuidance Optionsu Estimated Arrival

System Setup

Estimated Arrival

H u Navigation uuGuidance Options u Estimated Arrival

Sets the time format for the estimated arrival to a destination which is displayed on the guidance screen.

Select an option.

The following options are available:

• Arrival Time (factory default): Displays the estimated arrival time at a destination.

• Time Remaining: Displays the remaining time to a destination.

System Setup

Predictive Routing

H u Navigation uuGuidance Options u Predictive Routing

uuGuidance OptionsuPredictive Routing

Sets whether to use the predictive routing feature.

The following options are available:

• Enable: Sets the predictive route feature.

• Disable (factory default): Disables the feature.

Select an option.

uuGuidance Optionsu Delete Learning History

System Setup

Delete Learning History

H u Navigation uuGuidance Options u Delete Learning History

Select OK.

Auto Zoom

H u Navigation uuGuidance Options u Auto Zoom

Sets whether the map zooms in automatically according to the distance of the next guidance point.

Select an option.

The following options are available:

• ON (factory default): Sets the map to zoom in automatically according to the distance of the next guidance point.

• OFF: Disables the feature.

System Setup

Maneuver Assist Popup

H u Navigation uuGuidance Options u Maneuver Assist Popup

uuGuidance OptionsuManeuver Assist Popup

Sets whether to display the turn-by-turn popup when approaching the intersection.

The following options are available:

• Surface Street: Sets whether to display the turn-by-turn popup on the surface

• Freeway: Sets whether to display the turn-by-turn popup on the freeway.

Voice Guidance Language

H u Navigation uuGuidance Options u Voice Guidance Language

Sets the language for voice prompts.

1. Select an option(s).

2. Select Save.

street.

Select an option.

uuGuidance Optionsu Maneuver List

System Setup

Maneuver List

H u Navigation uuGuidance Options u Maneuver List

Sets the turn-by-turn instructions.

The following options are available:

• ON: Sets to display the turn-by-turn instructions on the map.

• OFF (factory default): Disables the feature.

Select an option.

System Setup

Tutorial

H u Navigation uuTutorial

Click on a listed feature to learn how to use it.

Select or to switch to the next or previous page.

Select Exit to exit a tutorial.

System Setup

Manage Places

H u Navigation uuManage Places

Edits your stored locations and avoidance areas.

The following options are available:

• Avoidance Areas: Allows you to avoid specific roads or areas.

2 Avoidance Areas P. 51

• Home: Edits home location.

2 Editing Home Location P. 22

• Saved Places: Edits saved places.

2 Editing a Saved Location P. 25 2 Deleting a Saved Location P. 26 2 Deleting All Saved Locations P. 26

• Recent: Edits recent destinations.

2 Editing Recent Destinations P. 55

• Downloaded Places: Edits downloaded places.

2 Editing Downloaded Places P. 55

Select an option.

System Setup

Avoidance Areas

Allows you to avoid specific areas and sections of road. You can enable and disable custom avoidances as needed.

uuManage Placesu Avoidance Areas

■

H u Navigation uuManage Places u Avoidance Areas

Adding an Avoid Area

1. Select .

2. Select Name to enter a name.

3. Select Area.

Continued

uuManage Places uAvoidance Areas

System Setup

4. Select an item to search a desired location.

5. Select Next.

6. Drag the map to add a desired

avoid location and then select Avoid.

7. Select Save.

System Setup

■

H u Navigation uuManage Places u Avoidance Areas

The following items are available:

• Name: Enters a new name.

• Area: Searches a new area.

uuManage Placesu Avoidance Areas

Editing an Avoidance Area

1. Select the area to edit from the list.

2. Select an item.

3. Select Save.

Continued

uuManage Places uAvoidance Areas

System Setup

1 Deleting Avoidance Areas

To delete all stored avoidance areas, select and then select Yes.

Deleting Avoidance Areas

■

H u Navigation uuManage Places u Avoidance Areas

1. Select .

u The selected area disappears

from the list.

2. Select Save.

System Setup

Editing Recent Destinations

1 Editing Recent Destinations

To delete all recent destinations, select and then select Yes.

1 Editing Downloaded Places

To delete all downloaded places, select and then select Yes.

H u Navigation uuManage Places u Recent

Editing Downloaded Places

H u Navigation uuManage Places u Downloaded Places

uuManage Places uEditing Recent Destinations

1. Select .

u The selected destination

disappears from the list.

2. Select Save.

1. Select .

u The selected destination

disappears from the list.

2. Select Save.

System Setup

Map Update

1 Map Update

Database Version

You will need this information when ordering a map update.

2 Obtaining a Navigation Update P. 104

H u Navigation uuMap Update

Updates navigation map data via Wi-Fi or USB flash drive.

The following options are available:

• Home Region Update (Wi-Fi): Installs and updates home region map with a Wi-Fi connection.

• Select Region Update (Wi-Fi): Installs and updates desired region map with a Wi-Fi connection.

• Full Map Update (USB): Installs and updates full map with a USB flash drive.

• Export DL Link for Full Map Update (USB): Exports link file for the download portal site to the USB flash drive.

• Database Version: Displays the map database version.

Select an option.

System Setup

Settings

H u Navigation uuSettings

Adjusts current vehicle position, restores all settings, and displays other information.

The following options are available:

• Adjust Vehicle Position: Manually adjusts the current position of the vehicle.

• Reset to Default: Restore all settings to the factory default values.

• Online Services: Displays the online services.

• About Software License: Displays the open source license information.

Select an option.

2 Adjust Vehicle Position P. 58

2 Data Reset P. 60

2 Online Services P. 59

2 About Software License P. 59

uuSettingsu Adjust Vehicle Position

System Setup

1 Adjust Vehicle Position

An apparent position error can occur where buildings, tunnels, and other objects block or reflect GPS signals, forcing the system to use “dead reckoning” to determine your location and direction.

Using this function to adjust vehicle position is not recommended. When the system reacquires a GPS signal, it will automatically place the vehicle in the correct location.

If you continually have to adjust the vehicle position, you may have problems with GPS reception or there may be database errors.

2 System Limitations P. 102

Arrow icons

Adjust Vehicle Position

H u Navigation uuSettings u Adjust Vehicle Position

Manually adjust the current position of the vehicle as displayed on the map screen if the position appears to be incorrect. Make sure the vehicle is in Park.

1. Scroll the map to position the arrowhead at your correct position.

2. Select arrow icons to position the arrowhead in the correct direction the vehicle is facing.

3. Select Done.

System Setup

Online Services

1 Online Services

•

Traffic Information available via Online Services

2 Traffic Information P. 87

•

Updating map data via Wi-Fi

2 Map Update P. 56

•

Searching facilities by phone number

2 More P. 76

For use of Online Services or for checking of all functions consult your dealer.

H u Navigation uuSettings u Online Services

uuSettingsu Online Services

Select an option.

The following options are available:

• Sign Up for Online Service: Sign up for online service.

• Online Service Status: Displays the online service status.

About Software License

H u Navigation uuSettings u About Software License

Displays the open source license information.

System Setup

Data Reset

1 Reset Factory Default Settings

When you want to reset the following options, see the below references:

•

Saved Places

2 Saved Places P. 23

•

Recent

2 Recent P. 74

•

Downloaded Places

2 Editing Downloaded Places P. 55

•

Breadcrumb Trail

2 Off-Road Breadcrumbs Display P. 84

When you transfer the vehicle to a third party, reset all settings to default and delete all personal data.

Reset Factory Default Settings

H u Navigation uuSettings u Reset to Default

You can restore all settings to the factory default values.

1. Select OK.

u A confirmation message

appears on the screen.

2. Select OK.

Navigation

This section describes how to enter a destination, select a route to take, and follow the

route to your destination. It also describes how to change your route or destination.

Entering a Destination ............................62

Saved Places ...........................................74

Recent ....................................................74

Gas Station .............................................75

More ......................................................76

Map Input...............................................77

Calculating the Route ..............................78

Viewing and Selecting the Routes ...........79

Viewing the Destination Information .......80

Driving to Your Destination ...................81

Viewing the Route ..................................81

Map Operation ........................................85

View (Map Orientation)...........................86

Traffic Information ............................. 87

Changing Your Route............................. 89

Stopping the Route ................................ 89

Taking a Detour ..................................... 89

Adding Waypoints ................................. 90

Editing a Route ...................................... 91

Changing Your Destination ................... 92

Selecting a Destination on the Map ........ 92

Entering a New Destination.................... 93

Navigation

Entering a Destination

1 Entering a Destination

The audio system can only provide route guidance from one navigation system at a time. When setting a destination on one system, any active route guidance with the other system is canceled, and the system you are currently using will direct you to your destination.

To use HondaLink®, you must connect your smartphone to the system. For more details about smartphone connection and how to use HondaLink®, see the Owner's Manual.

If you roll the right selector wheel on the steering wheel and select navigation & compass and then press the right selector wheel while on the map screen, the following items are available. Roll and press the right selector wheel to select the items.

•

Go home

•

Saved places

•

Recent

When en route, the following item is available.

•

Cancel route

Right Selector Wheel

H u Navigation u

This section describes how to enter a destination for route guidance.

The following options are available:

• : Sets a destination by voice control system.

2 Using Voice Commands P. 6 2 Voice Control Operation P. 12

• Keyword or Address: Sets a destination by entering a category, name, address, Intersection (Street 1 / Street 2), city name, or state name.

2 Using the Search Bar P. 63

• Nearby/Route/Map: Sets a search method for keyword.

• Go Home: Sets your home address as the destination.

2 Going Home P. 9

• Saved Places: Sets a destination by selecting a place stored in the saved list.

2 Saved Places P. 74

• Recent: Sets a destination by selecting a previous destination.

2 Recent P. 74

• Gas Station: Sets a destination by gas station.

2 Gas Station P. 75

• More: Sets a destination by selecting a category.

2 More P. 76

• Keyword Search: Displays the keyboard.

Select an option.

Navigation

Using the Search Bar

1 Using the Search Bar

Using Voice Command

You can say the names of popular, well-known locations. From the Voice Portal screen, say “Navigation.” Say “Find place,” then say a place name (e.g.,

“Honda”). Say the line number of screen (e.g., “1”). Say “Go” or “Yes” to set the route.

2 Using Voice Commands P. 6 2 Voice Control Operation P. 12

•

To search for a type of business, enter a category name, such as “gas station.”

•

To search for a business by name, enter all or part of the name.

•

To search for an address near you, enter the street number and street name.

•

To search for an address in another city, enter the street number, street name, city, and state.

•

To search for a city, enter the city and state.

If you want to delete the search history, select Reset to Default.

2 Reset Factory Default Settings P. 60

■

H u Navigation u

You can use the search bar to search for locations by entering a category, name, address, Intersection (Street 1 / Street 2), city name, or state name.

uuEntering a Destinationu

1. Enter a search term.

u The nearest locations by

corresponding to the search word are displayed below the search bar.

u Suggested search terms appear

below the search bar as you type.

2. Select or a nearest location on below the search bar.

u If you select nearest location,

proceed to step 4.

3. Select your destination from the list.

4. Select Go to set the route to your destination.

2 Calculating the Route P. 78

Continued

uuEntering a Destination u

Navigation

1 Changing the Search Area

Near Destination, Near Waypoint and Along Route can be set when the route is active.

Changing the Search Area

■

H u Navigation uuNearby/Route/Map

By default, your system finds locations closest to your current location. You can find a location near another city or location.

Select an option.

The following options are available:

• Current Position: Searches near your current location.

• Near Destination: Searches near your current destination.

• Near Waypoint: Searches near your waypoint, or current destination or current your location.

• Along Route: Searches along your current route.

• Select on Map: Searches around selected location on the map.

Navigation

Finding a Location Using Address

1 Finding a Location Using Address

Using Voice Command

You can say the entire address at once using voice commands. From the Voice Portal screen, say “Navigation.” Say “Enter address” on the voice command screen, then say the entire address. (e.g., “1-2-3-4 Main Street, Los Angeles, California”). Say “Change country” if you want to change the country. The system interprets the address. Say “Yes” or a line number of a screen if the destination list appears (e.g., “1”). Say “Go” or “Yes” to set the route.

2 Using Voice Commands P. 6 2 Voice Control Operation P. 12

■

H u Navigation uuMore uuAddress

The following options are available:

• House Number: Enters the house number to select the street.

2 Selecting a Street by House Number P. 67

• Street Name: Selects your destination street.

2 Selecting a Street P. 68

• City: Selects your destination city.

2 Selecting a City P. 69

• Zip Code (U.S.)/Postal Code (Canada): Enters the zip code or postal code to select the city.

2 Selecting a City by Zip Code or Postal Code P. 70

uuEntering a Destinationu

Select an option.

Continued

uuEntering a Destination u

Navigation

1 Selecting the State or Province

You can search other countries when you select

Select Country.

Selecting the State or Province

■

H u Navigation uuMore uuAddress

1. Select location name icon on the

right upper screen.

2. Select a state or province.

uuEntering a Destinationu

Navigation

Selecting a Street by House Number

■

H u Navigation uuMore uuAddress u House Number

1. Enter the house number and then

select .

2. Enter the name of your destination street and then select .

u Select a city when you are

prompted.

3. Set the route to your destination.

2 Calculating the Route P. 78

Continued

uuEntering a Destination u

Navigation

1 Selecting a Street

When entering the names of major freeways/ highways, you can use the following abbreviations. For interstates, use an “I” (e.g., I-10). For U.S. freeways, use “US” (e.g., US-18). For state freeways, use the two-character state designation (e.g., CA-

101). For county roads, use the appropriate designation (e.g., G-2). For Trans-Canada and Provincial highways, use “Hwy” (HWY-7). For County roads, use “CR” (CR-

32). For Regional Roads, use “RR” (RR-5).

Selecting a Street

■

H u Navigation uuMore uuAddress u Street Name

1. Enter the name of your destination

street and then select .

u If you search a freeway/

highway, the search results will be displayed. Select search result on the list, proceed to steps 3.

2. Enter the house number and then select .

3. Select your destination city from the list.

u Select an address when you are

prompted.

4. Set the route to your destination.

2 Calculating the Route P. 78

Navigation

Selecting a City

1 Selecting a City

Using Voice Command

You can find a city by using voice commands. From the Voice Portal screen, say “Navigation.” Say “Enter address” on the voice command screen, then say a city name. (e.g., “Los Angeles”). Say a line number of a screen (e.g., “1”). Say “Go” or “Yes” to set the route.

2 Using Voice Commands P. 6 2 Voice Control Operation P. 12

If your city is not listed, it may be part of a larger metropolitan area. Try entering the street first.

■

H u Navigation uuMore uuAddress u City

The name of the city where you are currently located is displayed.

uuEntering a Destinationu

1. Enter the name of a different city and then select .

2. Enter the name of your destination street and then select .

3. Enter the house number and then select .

4. Set the route to your destination.

2 Calculating the Route P. 78

Continued

uuEntering a Destination u

Navigation

1 Selecting a City by Zip Code or Postal Code

If your city is not listed, it may be part of a larger metropolitan area. Try entering the street first.

Selecting a City by Zip Code or Postal Code

■

H u Navigation uuMore uuAddress u Zip Code/Postal Code

1. Enter the zip code or postal code

of your destination and then select

2. Enter the name of your destination street and then select .

3. Enter the house number and then select .

4. Set the route to your destination.

2 Calculating the Route P. 78

uuEntering a Destinationu

Navigation

Finding a Location Using Coordinates

■

H u Navigation uuMore uuCoordinates

You can find a location using latitude and longitude coordinates. This can be helpful when geocaching.

1. Select the Latitude Direction to set North or South.

2. Select Latitude DMS and then enter a latitude. Select .

3. Select the Longitude Direction to set East or West.

4. Select Longitude DMS and then enter a longitude. Select .

5. Select Show Map.

6. Select Go to set the route to your

destination.

2 Calculating the Route P. 78

Continued

uuEntering a Destination u

Navigation

Select and hold.

Editing Shortcuts

■

H u Navigation uuMore

■ Customization screen

• To add shortcut icon

Select and hold empty space or shortcut icon.

u The customization screen appears

on the screen.

1. Swipe left to switch the next page.

2. Select .

3. Select Search Method or Place

Category.

4. Select an item.

5. Select Done.

Navigation

• To remove shortcut icon

Select and hold.

Drag and drop.

• To move shortcut icon

uuEntering a Destinationu

1. Select .

2. Select Done.

1. Select and hold an icon.

2. Drag and drop the icon to where

you want it to be.

3. Select Done.

uuEntering a Destination uSaved Places

Navigation

1 Saved Places

You can add, edit, or delete the saved place.

2 Saved Places P. 23

Using Voice Command

You can utilize a saved place by using voice commands. From the Voice Portal screen, say “Navigation.” Say “Saved places” on the voice command screen, then say a saved place (e.g., “Honda”). Say “Go” or “Yes” to set the route.

2 Using Voice Commands P. 6 2 Voice Control Operation P. 12

1 Recent

You can delete the recent destination.

2 Editing Recent Destinations P. 55

Using Voice Command

You can utilize a recent destination by using voice commands. From the Voice Portal screen, say “Navigation.” Say “Recent places” on the voice command screen, then say a line number of a screen (e.g., “1”). Say “Go” or “Yes” to set the route.

2 Using Voice Commands P. 6 2 Voice Control Operation P. 12

Saved Places

H u Navigation uuSaved Places

Select a saved places to use as the destination.

Recent

H u Navigation uuRecent

1. Select your destination from the

list.

2. Select Go to set the route to your destination.

2 Calculating the Route P. 78

Select an address from a list of your 20 most recent destinations to use as the destination. The list is displayed with the most recent destination at the top.

1. Select your destination from the list.

2. Select Go to set the route to your destination.

2 Calculating the Route P. 78

uuEntering a Destinationu Gas Station

Navigation

Gas Station

H u Navigation uuGas Station

Sets any gas stations as your destination.

1. Select your destination from the list.

2. Select Go to set the route to your destination.

2 Calculating the Route P. 78

uuEntering a Destination uMore

Navigation

1 More

Using Voice Command

You can find a place by the name using voice commands. From the Voice Portal screen, say “Navigation.” Say “Find place” on the voice command screen, then say a category (e.g., “Fast Food”). Say a subcategory if the subcategory screen is displayed. Say a line number of a screen (e.g., “1”). Say “Go” or “Yes” to set the route.

2 Using Voice Commands P. 6 2 Voice Control Operation P. 12

Downloaded Places

You can select downloaded places via HondaLink®. Downloaded Places will be grayed out when registered information is absent.

Phone Number

To use this function, it is necessary to turn on the online services.

2 Online Services P. 59

Select the category of a place (e.g., Restaurants, Gas Stations, Shopping) stored in the map database to search for the destination.

Finding a Location by Category

■

H u Navigation uuMore

1. Select a category.

u If you select other than

Categories, proceed to step 3.

2. Select a subcategory.

3. Select a place name from the list.

4. Select Go to set the route to your

destination.

2 Calculating the Route P. 78

Navigation

Map Input

1 Map Input

You can customize the map as you like using , or .

2 Map Operation P. 85

Select to return to the current location.

If you want to display a specific category of places, select and then select a category icon.

1 Selecting a POI

When POIs are too close together on the map, they are shown grouped together in a cluster and the top most POI in a cluster can be selected. You can select other POIs with / .

H u Navigation

Scroll the map to manually select an icon or a location as the destination.

Selecting a POI

■

H u Navigation

uuEntering a Destination uMap Input

1. Select any point on the map, a street, intersection, or category icon.

u Return to the current location

when you press the button.

2. Select Go to set the route to your destination.

2 Calculating the Route P. 78

1. Select a POI icon.

u The destination information

screen is displayed.

2 Viewing the Destination

Information P. 80

2. Select Go to set the route to your

destination.

u The system starts calculating

the route.

2 Calculating the Route P. 78

Navigation

Calculating the Route

This section describes how to calculate your route.

The following options are available:

• Save: Saves the location to the Saved Places list.

2 Saving a Saved Location P. 23 2 Saved Places P. 74

• Routes: Displays different routes.

2 Viewing and Selecting the Routes P. 79

• : Displays detailed location information.

2 Viewing the Destination Information P. 80

• / : Switches to other destination.

Select Go.

u The system calculates and displays

the route line on the map screen.

uuCalculating the RouteuViewing and Selecting the Routes

Navigation

Viewing and Selecting the Routes

View and select different routes to your destination.

1. Select your desired route.

u The estimated arrival time and

travel distance are displayed for each route.

2. Select Go.

u The system calculates and

displays the route line on the map screen.

uuCalculating the Route uViewing the Destination Information

Navigation

Viewing the Destination Information

If necessary, view information about the location you found before setting the route. You can confirm destination name, destination map, and distance. The phone number may also be available for some places.

1. Select a location name or a POI icon on the map.

The following options are available:

• : Makes a call to the displayed phone number. You need to pair your phone to the system to select the option. See the Owner’s Manual for details on paring.

• Go: Sets the route to your destination.

2 Calculating the Route P. 78

• Save: Saves the location to the Saved Places list.

2 Saving a Saved Location P. 23 2 Saved Places P. 74

• Routes: Displays different routes.

2 Viewing and Selecting the Routes P. 79

2. Select .

Navigation

Driving to Your Destination

1 Viewing the Route

When your phone is connected to Bluetooth® HandsFreeLink®, the navigation screen will switch to the incoming call screen when receiving a call.

You can stop your vehicle en route (e.g., to rest, stop for gas, etc.), and then continue on your route.

If you did not complete your route, the navigation restarts when you restart your vehicle.

Next guidance indicator

Viewing the Route

This section describes how to follow the route guidance to your destination.

Map Screen

■

The following options are available:

• Selects the next guidance indicator to replay the voice guidance for the next maneuver.

• : Sets whether to hear a voice guidance on and off.

After calculating the route to your destination, the route is displayed on the map screen.

2 During Route Guidance P. 8

As you drive, the system tracks your position on the map in real time and provides guidance as you approach each guidance point on the route.

Continued

uuDriving to Your Destination u Viewing the Route

Navigation

1 Turn List

Turn-by-Turn Directions

The next guidance point appears on the Driver Information Interface. The Turn-by-Turn directions may not be displayed if the information cannot be received correctly.

Turn List

■

The turn list screen displays turn-by-turn instructions and the distance between turns.

1. Set the Maneuver List to ON.

2 Maneuver List P. 48

2. Select on the map.

Navigation

Turn Information

1 Viewing the Route

Intersection View Screen

The intersection view screen displays a view of the upcoming intersection and which lane you should be driving.

You can also turn off the intersection view screen.

2 Maneuver Assist Popup P. 47

■

The turn information screen displays the turn on the map and the distance remaining before you reach the turn. The lane assist screen may display a view of the upcoming intersection.

Route Overview

■

H u Navigation uuRoute Options u Route Overview (when en

route)

The route overview screen displays the entire route and current vehicle position.

uuDriving to Your Destinationu Viewing the Route

Set the Surface Street in Maneuver Assist Popup to on.

2 Maneuver Assist Popup P. 47

Continued

uuDriving to Your Destination u Viewing the Route

Navigation

1 Off-Road Breadcrumbs Display

You can delete the off-road breadcrumbs.

2 Delete Breadcrumb Trail P. 36 2 Reset Factory Default Settings P. 60

Tracking line

Off-Road Breadcrumbs Display

■

If you set the off-road breadcrumbs to show, a series of lines (breadcrumbs) are displayed to track your movement on a off-road.

2 Breadcrumb Trail P. 35

Navigation

Map Operation

Customize the map, set a destination, and save a place from the map.

1. Select any point on the map.

2. Select an option.

u If you want to set a destination

or save a location in the map,

The following options are available:

• : Zooms in to the map.

• : Zooms out of the map.

• : Returns to the current location.

• : Selects the map orientation.

2 View (Map Orientation) P. 86

scroll the map and select the desired location.

2 Saved Places P. 23 2 Map Input P. 77

uuMap OperationuView (Map Orientation)

Navigation

1 View (Map Orientation)

The red arrow in the symbol always points North.

The bird’s eye view map switches to the Heading-up map while scrolling the map.

The scale of 3D Map is limited. If the screen does not switch to 3D Map, zoom in the map.

View (Map Orientation)

H u Navigation

Select the map orientation.

The following options are available:

• (North-up): Displays the map with North always pointing up.

• (Heading-up): Displays the map so that the direction you are traveling is always pointing up.

• (3D Map): Displays the bird’s eye view map.

Select an option.

Navigation

Traffic Information

1 Traffic Information

Continuously updated traffic information is available in major metropolitan areas across contiguous United States and some cities in Canada.

You can change the traffic information settings.

2 Traffic Icons P. 32

When you set the traffic feature, the system examines traffic conditions and optimizes the route for the shortest time. If a severe traffic delay occurs while you are navigating, the system searches for a faster route. If it finds one, the system will prompt you and you can choose to accept the new route. The system may route you through a traffic delay if a better alternative route does not exist. The delay time is added into your estimated time of arrival automatically.

The following options are available:

• Nearby Traffic: Displays the traffic flow and delays on nearby roads.

2 Viewing Traffic Information on Nearby Roads P. 88

• Traffic Along Route: Displays the traffic flow and delays on along route.

2 Viewing Traffic Information on Along Route P. 88

uuMap OperationuTraffic Information

Select on the map screen.

Continued

uuMap OperationuTraffic Information

Navigation

Viewing Traffic Information on Nearby Roads

■

H u Navigation uuNearby Traffic

View the traffic flow and delays on nearby roads.

Viewing Traffic Information on Along Route

■

H u Navigation uuTraffic Along Route

View the traffic flow and delays on along route.

Navigation

Changing Your Route

1 Stopping the Route

“Stop route”

2 Using Voice Commands P. 6 2 Voice Control Operation P. 12

You can also stop your route from the Destination List.

2 Editing a Route P. 91

1 Taking a Detour

“Detour”

2 Using Voice Commands P. 6 2 Voice Control Operation P. 12

If your current route is the only reasonable option, the system might not calculate a detour.

Stopping the Route

Stop the route guidance and remove the destination and all waypoints.

Select .

Taking a Detour

H u Navigation uuRoute Options u Detour (when en route)

Calculate a new route to avoid something ahead of you. The system creates a new route if possible and attempts to get you back on your original route as quickly as possible.

uuChanging Your RouteuAdding Waypoints

Navigation

1 Adding Waypoints

When you add a waypoint, the system may take some time to update the arrival time.

You can also edit route ordering on the Destination List.

2 Editing a Route P. 91

Adding Waypoints

Add waypoints (pit stops) along the route to your destination.

1. While en route, select a search

2. Select a place. Select Go.

3. Select Waypoint.

4. Select or and then move

5. Select Save.

method to add a new destination or waypoint.

2 Entering a Destination P. 62

u Select New Route to set the

location as your new destination.

2 Entering a New Destination

P. 93

the destination to the desired position.

u The route is automatically

recalculated and displayed on the map screen.

uuChanging Your RouteuEditing a Route

Navigation

Editing a Route

H u Navigation uuRoute Options u Destination List

You can edit destinations on your route.

Reordering Destinations

■

Deleting a Destination

■

1. Select or and then move the destination to the desired position.

2. Select Save.

u The route is automatically

recalculated and displayed on the map screen.

1. Select .

u Selected location will be

disappear on the list.

2. Select Save to delete.

u If you select Cancel, the

disappeared location will remain on the list.

Navigation

Changing Your Destination

Selecting a Destination on the Map

Select a new destination when en route by selecting a location on the map.

1. Select any point on the map, or a street, intersection, or category icon.

2. Select Go.

3. Select an option.

The following options are available:

• New Route: Sets the location as your new destination.

• Waypoint: Sets the location as the first waypoint in the Destination List screen.

2 Adding Waypoints P. 90

uuChanging Your DestinationuEntering a New Destination

Navigation

Entering a New Destination

H u Navigation u

Enter a new destination using the destination menu screen even when you are in route.

1. Select a search method to enter a

The following options are available:

• New Route: Sets the location as your new destination.

• Waypoint: Sets the location as the first waypoint in the Destination List screen.

2 Adding Waypoints P. 90

new destination.

2 Entering a Destination P. 62

2. Select a place and then select Go.

3. Select an option.

This page intentionally left blank.

Troubleshooting

Troubleshooting ..................................... 96

Map, Voice, Entering Destinations.......... 96

Traffic .................................................... 97

Guidance, Routing ................................. 98

Update, Coverage, Map Errors ............... 99

Display, Accessories................................ 99

Miscellaneous Questions ........................ 99

Troubleshooting

Map, Voice, Entering Destinations

Problem Solution

The Startup Confirmation screen is displayed every time I start the car.

The navigation system reboots by itself (returns to the opening screen).

How do I specify a destination when an entered city or street could not be found?

How do I delete saved places? Press the button. Select Navigation > > Manage Places > Saved Places >

I cannot hear the navigation system voice. Press the button. Select General Settings > System > System Volumes.

This is normal. The Startup Confirmation screen reminds you and your guest drivers to always operate the navigation system in a safe manner. The Startup Confirmation screen goes off after a certain period of time, even if you do not select OK.

A reboot can be caused by extreme temperatures or shock from bumpy roads, and does not necessarily indicate a problem. If this happens frequently, please see your dealer.

Try selecting the destination directly from the map.

2 Map Input P. 77

> Save.

Turn up Navigation Guidance, if volume level is low. For more details, see the Owner’s Manual.

uuTroubleshootinguTraffic

Troubleshooting

Traffic

Problem Solution

Traffic information is missing or is not displaying properly. What is wrong?

Verify the following:

●

Traffic information relies on a clear signal. If signal strength is low, traffic data may not be available.

●

Check that the traffic icons are turned on.

2 Traffic Icons P. 32

●

Online services may be off. If so, select Navigation > > Settings > Online Services > Sign Up for Online Service to turn on.

2 Online Services P. 59

●

If the situation persists, see your dealer for assistance.

●

Traffic information is available only in certain areas.

uuTroubleshootinguGuidance, Routing

Troubleshooting

Guidance, Routing

Problem Solution

The navigation system does not route me the same way I would go or the same way as other mapping systems.

The street I’m on is not shown on the map screen. The mapping database is constantly undergoing revision.

The vehicle position icon is not following the road. ●This is normal. The signals received from the GPS satellites are extremely weak

How do I stop the map from rotating as I drive along?

The “Arrival time” display sometimes increases even though I am getting closer to my destination.

My elevation (shown when I display the current position) seems to fluctuate even though my elevation has not changed.

My elevation is missing on the “current position” screen.

The navigation system attempts to generate the optimal route. You can change the route preferences used when calculating a route.

2 Route Calculation Method P. 42

and can easily be interrupted or interfered as your vehicle travels near tall buildings or in tunnels. Check your vehicle surroundings for anything that may be blocking the reception. If this happens frequently and there is no obstruction that is interfering the reception, please see your dealer.

●

Metallic tinting or other aftermarket devices can interfere with GPS reception. Please consult your dealer.

2 GPS P. 102

1. Press the button and then select Navigation.

2. Check that the map orientation is set to (heading-up) or (3D map).

3. Select and to select (north-up) on left side of the map.

The “Arrival time” is based on the speed limit on each road. Depending on the traffic conditions, the “Arrival time” may be calculated to be earlier or later.

This is normal. The elevation can vary ±100 ft (30 m) due to GPS calculation errors.

2 GPS P. 102

The elevation is only displayed if the GPS antenna can receive signals from at least four satellites. Try moving the vehicle into an open area. The elevation is also not displayed if the calculated elevation is zero or below sea level.

Honda Civic Hatchback (2023) Navigation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Contents

Quick Reference Guide

Overview—Functions at a Glance

HOME Screen

Touchscreen Operation

How to Enter Information

Map Screen Legend

During Route Guidance

Navigation—Home Addresses and Going Home

Navigation—Entering a Destination

Navigation—Changing Route or Destination

Voice Control Operation

Troubleshooting

How to Use This Manual

System Setup

Navigation

Troubleshooting