Mfr’s. Ng 236)
Assembly Instructions
§ Parts List
Be sure that the front end of the tongue is lower than the
Assembly
1. Mount the two wheel and tire assemblies on the axle and
secure with two 3/4" washers and two 3/16 x 1-1/2"
cotter pins.
2. Mount the frame assembly to the axle assembly and se
cure with two 5/16 X 4-5/8 L-shaped pins and two quick
pins. Be sure the axle curve is away from the ground.
3. Bolt the tongue to the frame assembly using two
3/8-16 X 2-1/4" capscrews, lockwashers, and hex nuts. washer and hex nut on each side. (Figure 2.)
end that is bolted to the frame.
4. Insert the box pivot assembly into the rear of the frame
assembly and secure with two 1/2 x 1-1/2" pins and two
quick pins.
5. Place the dump body on its tailgate to attach the pivot box
assembly. Place the two 3/S" long bushings, one in
each arm of the pivot box assembly. Insert a3/8-16 x 1"
capscrew with a 3/8" flatwasher through the trailer body
sides and through eachbushing and secure with3/8" lock-
FDR USE WITH ALL RIDING UNITS
Part Nq. 24744-4
Supersedes 24744
6. Place the box catch clevis over the tongue and insert a
3/8-16 X 2-3/4” capscrew through the clevis and tongue
from the side opposite the box catch handle. Place the
box catch spring over the end of the capscrew and secure
with a 3/8" washer and hex, locknut. The box catch
clevis should move freely, do not overtighten. The larger
hook of the box catch spring is then placed over the tongue
and the smaller one against the box catch handle to hold
the catch toward the rear of the dump cart.
7. Place the box guide plate inside the dump box with the
grooved end extending through the slot in the box floor.
Position the box catch plate on the outside with the up
turned end toward the box bottom and secure with two
3/8-16 X 1" capscrew, lockwashers and hex nuts.
Lubrication
The dump cart has two standard sized grease fittings, one
on each wheel, which require occasional lubrication with
general purpose automotive grease. Before lubricating,
wipe each grease fitting to prevent grit and dirt from being
carried into the bearings with the new grease. Lubricate
all pivot points arid the box catch clevis with SAE-10 oil
frequently.
Tires
The tires of the dump capt are inflated for shipping with
pressure in excess of the normal amount. For normal
lawn use deflate the tires until a pressure of 6-8 lbs. P. S. I.
is reached. When carrying heavy loads, or when used with
the vacuum collector, it will be necessary to increase this
pressure, to 14-16 lbs. P. S.I. to prevent damage to tires
or wheels.
Operation
The dump cart is designed to easily haul 1, 000 lbs. of any
type of material and has a 7 cubic ft. capacity struck and
10 cubic ft, heaped. The box can easily be unlatched with
out detaching from the tractor and can be turned completely
upside down by tilting up and back to empty all contents
without shoveling. The tailgate is detachable.
DUMP CART
No* Description Part No.
GATE-end
1
2 FILM-Homelite LM-01744-49
SCREW-cap, 3/8-16 x 1
3
4
BUSHING
5
NUT-hex, 3/8-16
6
WASHER-lock LM-09169-65
7 WASHER-flat, 3/8
8 PIVOT ASSEMBLY-box
PIN-pivot
9
PIN-quick
10
11
AXLE ASSEMBLY
12 WHEEL & TIRE ASSEMBLY
13
14
15
16
Includes:
BEARING
TUBE
TIRE
WHEEL
ALWAYS FURNISH MODEL AND SERIAL NUMBER WHEN ORDERING PARTS.
LM-01020-03
LM-09077-31
LM-81510-76
LM-09169-50
LM-09173-78
LM-01020-24
LM-01020-04
LM-S1610-45
LM-01020-27
LM-01703-20
LM-0I703-18
LM-01530-38
LM-01020-52
LM-01703-19
Qty.
1
1
4
2
6
6
3
1
2
5
1
2
2
2
2
2'
No.
17
18 PIN-cotter, 3/16 X 1-1/2
19 PIN
20
21
22 PIN-inner
23
24
25
26
27
28
29
30 PLATE-box gqide
Description Part No. Qty.
WASHER-Hat, 3/4
FRAME ASSEMBLY
TONGUE ASSEMBLY
SCREW-cap, 3/8-16 x 2-1/4
SPRING-tor Sion
NUT-hex lock, 3/8-16
PLATE-box catch
CLEVIS ASSEMBLY
SCREW-cap, 3/8-16 x 2-3/4
BODY-trailer
Accessory
PAINT-blue, 14 oz. spray can LM-16076-89
LM-09184-32
LM-09184-59
LM-80112-04
LM-01020-35
LM-01020-37
LM-01052-49
LM-09193-62
LM-01020-75
LM-09234-28
LM-01020-40
LM-01020-51
LM-09219-73
LM-01020-02
LM-01020-05
2
2
2
1
1
1
2
1
1
1 .
1
1
1
1
1
I i
PRINTED IN U.S.A.
HOMELITr
к textroni
PORT CHESTER, NEW YORK, U.S.A. 10573
CMVISION
v.„ y
E2375FZ
Loading...