Holux GPSmile Pocket PC User Manual

Pocket PC

User’s manual

Safety Instructions for
Holux GPSmile 60

Important safeguards

All safety instructions must be read carefully and must be fully understood,
before attempting to use Holux GPSmile 60. This manual contains the
safety instructions that must be observed in order to avoid potential hazards
that could result in personal injuries or could damage Holux GPSmile 60.
The safety instructions have been classified according to the seriousness of
the risk, as follows:

Signal Word Meaning

! DANGER

! WARNING

! CAUTION

CAUTION

NOTE

Indicates an imminently hazardous situation, which if
not avoided, will result in death or serious injury .

Indicates a potentially hazardous situation, which if
not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation, which if
not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation, which if
not avoided, may result in property damage.

Provides important information.

- 2 -

Introduction

Thank you very much for your purchase of Holux GPSmile 60.

Please be sure to read this manual before using Holux GPSmile 60, and
ensure that you are aware of the correct handling procedures.

• Please be sure to read the “ Important Safety Information” section in this

document to learn about important safety issue

• After reading this document, keep it in a convenient place for future

reference.

Copyright Information

© 2005 All rights reserved. Under the copyright laws, this manual cannot be
reproduced in any form without the prior written permission. No patent
liability is assumed, with respect to the use of the information contained
herein.

Microsoft®, Windows®, ActiveSync®, and PowerPoint® are registered
trademarks, and Windows CE™ is a trademark, of Microsoft Corporation.

The names of other actual companies, products, and brand names
mentioned herein may by trade names, service marks, trademarks, or
registered trademarks of their respective owners.

- 3 -

Important Safety Information

Read this information before using Holux GPSmile 60.
To reduce the risk of bodily injury, electric shock, fire, and damage to

the equipment observe the following precautions.

General Precautions

Avoid hot areas: The product should be placed away from heat sources

such as radiators, heat registers, or other products (including amplifiers) that
produce heat. Please don't put this product in the high-temperature place
and the vehicles in high temperature. The heat not only causes the product
deformed and battery defective but also has the fire and breakdown.

Avoid wet areas: Never use the product in a wet location.
Avoid pushing objects into product: Never push objects of any kind into

cabinet slots or other openings in the product. Slots and openings are

provided for ventilation. These openings must not be blocked or covered.
Mounting Accessories: Do not use the product on an unstable table, cart,

stand, tripod, or bracket. Any mounting of the product should follow the
manufacturer’s instructions, and should use a mounting accessory
recommended by the manufacturer.

Avoid unst able mounting: Do not place the product with an unstable base.
Use product with approved equipment: This product should be used only

with personal computers and options identified as suitable for use with your
equipment.

Avoid abnormal usage/disassembling: Please don't enforce it to be

discharged or overcharged/overdischarged with over current or high-tension
supply. Do not disassemble, repair, remodel, or pressurize this product;
otherwise, it will cause the fire, electric shock, scorch and malfunction.

Adjust the volume: Turn down the volume before using headphones or

other audio devices.

Avoid use for drivers when driving: The driver should not use this product

when driving.

- 4 -

GPS Usage Precautions

Please don’t use this product close to wireless machines; otherwise,
malfunction will be caused.

This product is delicate electronic machine; thus, please do not put it
in the places with strong static and electric waves.

GPS may not be efficiently receivable if using this product under
following condition:

• Tunnel or basement

• Parking lot in the building

• Indoor

• Under the viaduct

• In the gross forest

Safety Precautions for Battery

Warning

To reduce the risk of fire or burns, do not disassemble,
crush, puncture, short external contacts, or dispose of in fire
or water.

Danger of explosion if battery is incorrectly replaced.

Replace only with specified batteries.

Battery may require recycling in accordance with local laws.
Contact your local regulatory authorities for more

information.

Your battery should not be thrown in the trash can.

• Please carefully read these precautions before using Holux GPSmile 60,

and ensure that you are aware of the correct handling procedures.

- 5 -

• The precautions provide essential information for the protection of the

user and others from possible injury and property damage. They also
provide information on the safe handling of this product.

• Please check that you fully understand the definition of the following messages

(signs and graphical symbols) before reading the text, and always follow the
instructions provided.

- 6 -

Supplementary Information: “The product complies with the

requirements of the low Voltage Directive
73/23/EEC and the EMC Directive
89/336/EEC.”

Weitere Informationen: “Das Produkt entspricht den Anforderungen

der Niederspannungsrichtlinie 73/23/EG
und der EMC-Richtlinie 89/336/EG.”

Informations
complérnentaires:

“Ce produit est conforme aux exigences de
la directive sur les basses tensions
73/23/CEE et de la directive EMC
89/336/CEE.”

Información
complementaria:

“El Producto cumple los requistos de baja
tensión de la Directiva 73/23/CEE y la
Directiva EMC 89/336/CEE.”

Ulteriori informazioni: “Il prodotto é conforme ai requisiti della

direttiva sulla bassa tensione 73/23/EG e la
direttiva EMC 89/336/EG.”

Ytterligare information: “Produkten uppfyller kraven enligt

lågspänningsdirektiver 73/23/EEC och
EMC-direktiv 89/336/EEC.”

- 7 -

Working Environment

This product was designed to fulfill the EMC (electromagnetic compatibility)
requirements for “residential, commercial and light industry environments.”

The use of this product in working environments other than “residential,
commercial and light industry environments” is not approved.

For example, the following environments are not approved:

• Industrial Environments (environments with a main voltage > 230V~)

• Medical Environments

• Automotive Environments

• Aircraft Environments

Any consequences resulted from the use of this product in working
environments that are not approved are not the responsibility of the
manufacturer.

The consequences of the use of this product in non-approved working
environments may be:

• Interference with other devices or machines in the nearby surrounding

area

• Malfunction of, or data loss from, this product caused by disturbances

generated by other devices or machines in the nearby surrounding area

Therefore, the manufacturer strongly recommends that the electromagnetic
compatibility of this product be suitably tested in all non-approved working
environments before use. In the case of automobiles or aircraft, the
manufacturer or airline respectively should be asked for permission before
use of this product.

Furthermore, for general safety reasons, the use of this product in
environments with explosive atmospheres is not permitted.

- 8 -

CE Compliance

This product and the original options are designed to observe the related
EMC (electromagnetic compatibility) and safety standards. However, the
manufacturer cannot guarantee that this product still observes these EMC
standards if options or cables not produced by the manufacturer are
connected or implemented. In this case, the persons who have connected or
implemented those options or cables have to make sure that the system
(Holux GPSmile 60 plus options or cables) still fulfills the required standards.
To avoid general EMC problems, the following advice should be observed:

• Only CE marked options should be connected or implemented

• Only best shielded cables should be connected

Canadian Notice

This Class B digital apparatu s meets all requirements of the Canadian
Interference-Causing Equipment Regulations.

- 9 -

FCC Notice
“Declaration of Conformity”

This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

• Connect the equipment into an AC outlet socket, on a different circuit

from which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received. Including
interference that may cause undesired operation.

- 10 -

Caring for the Environment by Recycling in the
European Union

This symbol on the product or on its packaging indicates that
this product must not be disposed of with your other household
waste. Instead, it is your responsibility to designated collection
point for the recycling of waste electrical and electronic
equipment. For more information about where you can drop off
your waste equipment for recycling, please contact your local
city office, your household waste disposal service or the shop
where you purchased the product.

- 11 -

Chapter 1: Getting Started..................................................... 14

Welcome.......................................................... 14

Finding Information.......................................... 15

Chapter 2: Basic Skills........................................................... 16

System Overview............................................. 16

Battery Switch.................................................. 18

Using the Navigation Button ............................ 19

Using the Battery ............................................. 19

Charging the Battery........................................ 21

Initial Setup and Touch Screen Correction ...... 23

Inserting a SD Card ......................................... 24

Removing a SD Card....................................... 24

Connecting to a PC ......................................... 25

Today Screen................................................... 26

Using the Programs......................................... 30

Checking System Information.......................... 32

Customizing Settings....................................... 32

Adding or Removing Programs in ROM and

RAM ................................................................ 33

Adding Programs Using ActiveSync................ 33

Adding Programs Directly from the Internet .... 34

Adding Programs to the Start Menu ................ 35

Removing Programs........................................ 35

Setting Passwords........................................... 36

Chapter 3: Microsoft ActiveSync............................................ 37

Changing the Synchronization Schedule ........ 39

Chapter 4: GPS Function....................................................... 37

Enabling the GPS Function ............................. 37

Using GPS Power Control ............................... 40

Using Navigation Control................................. 43

Chapter 5: Additional Information .......................................... 46

Table of Contents

Resetting.......................................................... 47

Clearing Memory ............................................. 48

- 12 -

Specifications....................................................48

- 13 -

Chapter 1: Getting Started

Chapter 1:

Getting Started

Welcome

Congratulations on purchasing Holux GPSmile 60. Due to its size and
capabilities, you can keep your most important business and personal
information up-to-date and close at hand. Microsoft® ActiveSync®
increases the power of Holux GPSmile 60 by allowing you to synchronize
the information on your PC with Holux GPSmile 60.

- 14 -

Chapter 1: Getting Started

Finding Information

This manual describes features, provides program overviews, and
describes how to connect Holux GPSmile 60 to your PC, a network, or the
Internet. For instructions on setting and installing ActiveSync, consult the
documentation that came with ActiveSync.

For information on See this source

Programs on Holux GPSmile 60 The User’s Guide and online help.

Additional programs that can be
installed on Holux GPSmile 60

Connecting to and synchronizing
with a PC

Last-minute update and detailed
technical information

Up-to-date information on Holux
GPSmile 60

To view Help, tap

Holux GPSmile 60 Companion CD.

The Quick Start Card or ActiveSync
Help on your PC. To view Help, open
the Microsoft ActiveSync
application, and then click Help.

The Read Me files, located in the
Microsoft ActiveSync folder on the
PC and on Holux GPSmile 60
Companion CD.

http://www.guidetek.com.tw

and then Help.

- 15 -

Chapter 2: Basic Skills

r

r

Chapter 2:

Basic Skills

This chapter identifies the system components and describes the use and
customization of Holux GPSmile 60.

System Overview

Main Unit (Front View)

Indicator light

Volume U P

Volume D own

Earphone connecto

Rotate button

Hold Switch.

SD Card Slot

Power button

Microphone

Program button 4

Program button 3

Initial Settings of the Program Buttons

• Program button 1 = ezGO(Quick menu)

• Program button 2 = Navigator application launch buttons

• Program button 3 = Calendar / (Zoom in/ Optional)

• Program button 4 = Contacts / (Zoom out / Optional)

Navigation button

Speake
Program button 1

- 16 -

Chapter 2: Basic Skills

NOTE

The zoom in/ zoom out depending on whether your map
support or not.

Main Unit (End View)

ActiveSync Cable Port

Main Unit (Back View)

SD Card

Battery Switch

Battery lock

Battery Pack

Supply Stop

Styl us

Power Button

The power button performs the functions described in the table below.

Power button When the power is off When the power is on

Press and hold. The power turns on. The screen light

alternately turns on/off.

Press it quickly. The power turns on. The power turns off.

- 17 -

Chapter 2: Basic Skills

Battery Switch

The battery switch connects and disconnects the battery power from Holux GPSmile

60. The original factory setting of the switch is set to the right position (the “stop”
side). When using Holux GPSmile 60 for the first time, you need to set the battery
switch to the left position (the “supply” side).

CAUTION

Setting the Battery Lock

1. Use the stylus to slide the battery lock to the up position (the “lock” side)

See “To install the battery“ later in this chapter.

.

Switching the battery switch to the “stop” position at any
time leads to loss of data.

Lock

Battery Lock

Unlock

Battery/Alarm LED Descriptions

Flashing orange

Orange
Green
Yellow

Using the Stylus

When the preset alarm time (set through Calendar or
Tasks) goes off, the indicator starts flashing.

Indicates charging of the battery.
Indicates full charge of the battery.
The ambient temperature is too high or too low and

battery charging will stop.

- 18 -

Chapter 2: Basic Skills

The stylus is used for menu selection or data input on the touch screen of
Holux GPSmile 60.

• Tap—Touch the screen once with the stylus to open items and select

options.

• Drag—Hold the stylus on the screen and drag it across to select text

and images. Drag in a list to select multiple items.

• Tap and Hold—Tap and hold the stylus on an item to see a list of

actions available for that item. On the pop-up menu that appears, tap
the action you want to perform.

CAUTION

When you operate the touch screen of Holux GPSmile 60,

use the supplied stylus. Please use touch panel carefully

and don’t place it on or under the sharp objects.
If the tip of the stylus is damaged, do not use it. If you

operate the touch screen with a damaged stylus or a
ballpoint pen, the touch screen may be damaged.

When the stylus is damaged, please purchase a new one.

Using the Navigation Button

The navigation pad consists of five buttons. You can use them to move
horizontally and vertically on the touch screen for selecting the item you
want.

In a text field, use the navigation pad to move the cursor right or left,
character by character.

NOTE

The cursor movement is different depending on the screen.
When the cursor is at the right or left side of the touch
screen, it may not move.

Using the Scroller

You can move the cursor on the touch screen by moving the Scroller up and
down, as well as launching a program by pressing the Scroller.

NOTE

- 19 -

The cursor movement is different depending on the screen.
When the cursor is at the right or left side of the touch

Chapter 2: Basic Skills

;

screen, it may not move.

Using the Battery

To install the battery:

1. Ensure that the device is turned off.

2. Insert the left side of the battery into the battery slot at on angle, and press down
the right side into the slot until it clicks.

3. Insert the tip of the stylus into the battery lock.

4. Slide the lock to the lock position.

To remove the battery:

1. Insert the tip of the stylus into the battery lock.

2. Slide the lock to the unlock position.

3. Take the battery out of the slot.

CAUTION

You can replace the main battery pack without data loss
because Holux GPSmile 60 has a rechargeable backup
battery. However, the capacity of the backup battery is
limited

therefore, when you replace the main battery pack,

- 20 -

Chapter 2: Basic Skills

install the new one as soon as possible.

Charging the Battery

Charge Holux GPSmile 60 by using the AC adaptor:

Connect one end of AC adaptor (Mini USB

X) into the mini USB Client port

Z and connect the other end Y to an electrical outlet to charge Holux

GPSmile 60.

NOTE

Maintain an ambient temperature from approximately 32°F
to 104°F (0°C to 45°C) while charging the battery.

When the battery is being charged, the battery/alarm LED
is orange; when the battery is fully charged, the
battery/alarm LED changes to green.

- 21 -

Chapter 2: Basic Skills

Charging through Active Sync cable

Please use Active Sync cable when you have to synchronize your device
and your computer while charging your device via miniUSB. When you use
Active Sync cable to establish connection between your device and the PC,
plug the miniUSB connector of the AC Adaptor into miniUSB charger
located at the middle of Active Sync cable to start charging.

Prolonging the Battery Life

• Use Holux GPSmile 60 with the AC adapter during the following high

power consumption conditions:

• In addition:

 Select the short power-off time in the setting menu to shorten the

amount time and Holux GPSmile 60 remains on if it is not used.

 Turn off the screen light.

 Set the screen brightness to the power saving mode and shorten

the light turn-off time.

 Use Holux GPSmile 60 with an ambient temperature between

59°F and 77°F (15°C and 25°C). This temperature range is the
most effective for the battery.

 When you use Holux GPSmile 60 in high or low temperature

environments, the operable time is shortened due to the
decrease of the battery capacity.

• The removable battery has a limited life. Repeated

charging/discharging of the battery gradually decreases the operable
time. When the operable time has been diminished, it is time to replace
the removable battery with a new one.

 Do not leave Holux GPSmile 60 in a place of high or low temperature. It

may shorten the battery life.

CAUTION

If you have not used Holux GPSmile 60 for several days, its
battery charge level reading may be inaccurate. Fully
recharge the battery before using.

- 22 -

Chapter 2: Basic Skills

Protecting Data from Low Battery Charge Levels

If the battery charge level becomes extremely low or the battery becomes
flat, the memory data stored in Holux GPSmile 60 could be lost.

When the low battery status icon or alarm message appears, immediately
connect the AC adapter with Holux GPSmile 60 to charge the battery.

• The removable battery gradually discharges even if Holux GPSmile 60

is not being used. When Holux GPSmile 60 is left idle for a long time, the
removable battery may change to will become flat.

• It is recommended to save Holux GPSmile 60’s memory data to your PC

or storage card.

• The manufacturer is not responsible for the data change or clearance

due to battery discharge.

Initial Setup and Touch Screen Correction

When using Holux GPSmile 60 for the first time, follow the initial setup
procedures below, after the battery has been charged. When you slide the
battery switch to the “supply” position
60 powers on automatically and the Welcome screen appears. Tap the
screen to start the following setup.

and install the battery, Holux GPSmile

1. Complete the touch screen correction.

When the align screen appears, tap the center of the cross target with
the stylus. The next target position changes upon tapping the target.
Five taps completes the positioning correction. The screen then
changes to the stylus screen.

NOTE

2. Follow the on-screen instructions describing how to use the stylus, and

then tap Next.

NOTE

3. Follow the pop-up menu instructions.

If an object touches the screen during correction, the
correction is cancelled. Repeat the correction procedure.

For more information on stylus operation, see “Using the
Stylus” earlier in this chapter.

- 23 -

 Read the on-screen explanation and then follow the instructions.

Display the pop-up menu, and then cut and paste the data
according to the screen instructions.

 After you finish the paste operation, tap Next.

4. Set the time zone.

 When tapping the ▼ mark, the city and the time zone list appears.

Tap the desired city and time zone.

 When the setup is completed, tap Next.

5. Complete the initial setup.

 When the complete screen appears, the initial setup is

completed.

 After tapping the screen, you can use Holux GPSmile 60.

NOTE

When you tap the complete screen, the Today screen
appears.

Inserting a SD Card

Chapter 2: Basic Skills

1. Remove the dummy card from the SD card slot.

2. Insert the card with its metal contact surface facing the top of Holux
GPSmile 60.

3. Press down the card until it clicks in place.

- 24 -

Chapter 2: Basic Skills

Removing a SD Card

1. Lightly press down the card until a click is heard. The card pops out
slightly from the slot.

2. Pull out the card straight.

Connecting to a PC

Before connecting Holux GPSmile 60 to a PC, check the following:

• ActiveSync has been installed on your PC. (For more information, see

Chapter 3.)

• ActiveSync ports: the position of the ActiveSync port on your PC may

differ according to the PC type.

Connect Holux GPSmile 60 directly to your PC using the supplied
ActiveSync cable:

1. Connect the serial connector of the mini USB cable to the ActiveSync
Client port of Holux GPSmile 60.

2.

Connect the USB connector of the ActiveSync cable to the ActiveSync port of
your PC.

- 25 -

Chapter 2: Basic Skills

PDA Mounting Holder and Stand

1) Align the slots with the notches (A) and attach the stand to the holder (B)
as shown.

2) Ensure that slots and notches are placed in the proper position and fully
locked.

(A) (B)

- 26 -

Chapter 2: Basic Skills

(B)

3) Attach the Compal Mounting suction cup to the window (A) and press the

suction cup clip in the direction of the arrow to fasten it to the surface (B).

Warning! Do not unfasten the stand with the PDA still in the holder, you may
drop the

PDA and damage it.

Notes:

¾ Make sure that the glass surface is clean.

¾ To unfasten the stand, pull the suction cup clip out.

4) Carefully press down the tab (A) and pull down the holder out (B) as

shown.

(A)

- 27 -

A

5) Place the PDA phone inside the holder as shown.

Chapter 2: Basic Skills

B

6) Push the holder back into place.

- 28 -

Chapter 2: Basic Skills

Today Screen

When you turn on Holux GPSmile 60 for the first time each day (or after 4
hours of inactivity), the Today screen displays. You can also display it by
tapping
important information of the day.

The following are some of the status icons you may see.

Status Icon Meaning

and then Today. On the Today screen, you can see at a glance

NOTE

Turn all sounds on.

Turn all sounds off.

Main battery is charging.

Main battery is low.

Main battery is very low.

Main battery is full.

Connection is active.

Connection is inactive.

Notification that one or more e-mail messages were
received.

Notification that one or more instant messages were
received.

If more notification icons need to be displayed than there is
room to display them, the Notification icon
Tap the icon to view all notification icons.

displays.

- 29 -

Chapter 2: Basic Skills

Using the Programs

You can switch from one program to another by selecting it from the
menu. (You can customize which programs you see on the menu. For
information, see “Customizing Settings” later in this chapter.) To access
some programs, tap

You can also switch to certain programs by pressing the program button
assigned to those programs. Holux GPSmile 60 has program buttons
located on the front of the device. The icons on the buttons identify the
programs they activate.

NOTE

Some programs have abbreviated labels for check boxes
and drop-down menus. To see the full spelling of an
abbreviated label, tap and hold the stylus on the label. Drag
the stylus off the label so that the command is not carried
out.

> Programs, and then the program name.

- 30 -

Chapter 2: Basic Skills

The following table contains a partial list of programs that are included.
(Look for additional programs in Holux GPSmile 60 Companion CD.)

Icon Program Description

ActiveSync Synchronize information between Holux

Calendar Keep track of your appointments and

Contacts Keep track of your friends and

Pocket Internet
Explorer

Messaging Send and receive email messages.

Windows Media Play Play digital audio and video files.

Notes Create handwritten or typed notes,

Tasks Keep track of your tasks.

Pocket Excel Create new workbooks or view and edit

Pocket Word Create new documents or view and edit

MSN Messenger Send and receive instant messages with

GPSmile 60 and PC.

create meeting requests.

colleagues.

Browse Web and WAP sites and
download new programs and files from
the Internet.

drawings and recordings.

Excel workbooks created on your PC.

Word documents created on your PC.

your MSN Messenger contacts.

- 31 -

Chapter 2: Basic Skills

Checking System Information

The system information program displays the system information such as
CPU clock, CPU stepping, OS version, PIC version, and UUID. The

information is displayed in the Identity, Memory, Driver and System items.

To check system information, tap

> Settings > System > SysInfo.

Tools Menu

The Tools menu displays the system information and allows the text to be
exported.

• Export exports all system information parameters to a text (*.txt) file.

Customizing Settings

You can customize Holux GPSmile 60 by adjusting the settings and
installing additional software.

Adjust the settings to suit the way you work. To see available options, tap

> Settings > Personal or System tab located at the bottom of the screen.

You might want to adjust the following:

• Clock & Alarms to change the time or to set the alarms

• Menus to customize what appears on the menu, and to enable a

pop-up menu from New

• Owner Information to enter your contact information

- 32 -

Chapter 2: Basic Skills

• Password to limit access to Holux GPSmile 60

• Power to maximize the battery life

• Today to customize the look and the information that is displayed on

the Today screen

• Screen to change the display mode to Landscape or to align the screen

Adding or Removing Programs in ROM and
RAM

Programs added to Holux GPSmile 60 at the factory are stored in read-only
memory (ROM). You cannot remove this software, and ROM contents are
never lost. ROM programs can be updated using special installation
programs with a *.xip extension. All other programs and data files added to
Holux GPSmile 60 after the factory installation are stored in random access
memory (RAM).

You can install programs created for Holux GPSmile 60; the most popular
place to find Holux GPSmile 60 software is on Holux GPSmile 60 Web site
(http://www.microsoft.com/mobile/pocketpc). Before you install any
programs for the first time, be sure that Holux GPSmile 60 has enough
memory.

Adding Programs Using ActiveSync

Install the appropriate software for Holux GPSmile 60 on your PC before
installing it on Holux GPSmile 60.

1. Determine Holux GPSmile 60 processor type so that you know which
version of the software to install.

Tap
make a note of the information in Processor.

2. Download the program to your PC (or insert the CD or disk that contains
the program into your PC). You may see a single *.xip, *.exe, or *.zip file,
a Setup.exe file, or several versions of files for different device types
and processors. Be sure to select the program designed for Holux
GPSmile 60 and its processor type.

- 33 -

> Settings. On the System tab, tap About. In the Version tab,

Chapter 2: Basic Skills

3. Read any installation instructions, Read Me files, or documentation that
comes with the program.

Many programs provide special installation instructions.

4. Connect Holux GPSmile 60 to your PC.

5. Double-click the *.exe file.

 If the file is an installer, the installation wizard begins. Follow the

directions on the screen. Once the software has been installed
on your PC, the installer automatically transfers the software to
Holux GPSmile 60.

 If the file is not an installer, an error message displays stating that

the program is valid but it is designed for a different type of PC.
Transfer this file to Holux GPSmile 60. If you cannot find any
installation instructions for the program in the Read Me file or
documentation, use ActiveSync Explorer to copy the program file
to the Program Files folder on Holux GPSmile 60. For more
information on copying files using ActiveSync, see ActiveSync
Help.

 If the application is not for Windows Mobile 2003 Second Edition,

a message displays stating that the program is designed for a
previous version. In this case, the program you have installed
may not display properly.

6. Once the installation is complete, tap

> Programs, and then the

program icon.

Adding Programs Directly from the Internet

1. Determine Holux GPSmile 60 processor type so that you know which
version of the software to install.

Tap

make a note of the information in Processor.

2. Download the program to Holux GPSmile 60 straight from the Internet
using Pocket Internet Explorer. You may see a single *.xip, *.exe, or
*.zip file, a Setup.exe file, or several versions of files for different device
types and processors. Be sure to select the program designed for Holux
GPSmile 60 processor type.

> Settings. On the System tab, tap About. In the Version tab,

- 34 -

Chapter 2: Basic Skills

3. Read any installation instructions, Read Me files, or documentation that
comes with the program. Many programs provide special installation
instructions.

4. Tap the file, such as a *.xip or *.exe file. The installation wizard begins.
Follow the directions on the screen.

If the application you have installed is not for Windows Mobile 2003
Second Edition, the program may not display properly.

Adding Programs to the Start Menu

Tap > Settings > Menus > the Start Menu tab, and then the check box

for the program. If you do not see the program listed, you can either use File
Explorer on Holux GPSmile 60 to move the program to the Start Menu folder,
or use ActiveSync on your PC to create a shortcut to the program and place
the shortcut in the Start Menu folder.

• Using File Explorer on Holux GPSmile 60—Tap > Programs >

File Explorer, and locate the program (tap the folder list, labeled My
Documents by default, and then Local Dev ice to see a list of all folders

on Holux GPSmile 60). Tap and hold the program, and tap Cut on the
pop-up menu. Open the Start Menu folder located in the Windows
folder, tap and hold a blank area of the window, and tap Paste on the

pop-up menu. The program appears on the menu. For more information
on using File Explorer, refer to Holux GPSmile 60 user’s guide.

• Using ActiveSync on your PC—Use the Explorer in ActiveSync to

explore your device files and locate the program. Right-click the

program, and then click Create Shortcut. Move the shortcut to the Start

Menu folder in the Windows folder. The shortcut now appears on the
menu. For more information, see ActiveSync Help on your PC.

Removing Programs

Tap > Settings. On the System tab, tap Remove Programs.

If the program does not appear in the list of installed programs, use File
Explorer on Holux GPSmile 60 to locate the program, tap and hold the

program, and then tap Delete on the pop-up menu.

- 35 -

Setting Passwords

You can password-protect your data and settings.

Chapter 2: Basic Skills

1. Tap

2. Select the type of password you would like to use.

3. Enter a password and tap OK.

4. Tap Yes on the confirmation screen. The password is saved and the
screen returns to the Personal tab screen.

If you tap Yes on the confirmation screen to return to the Personal tab

screen, you must enter the password each time you use Holux GPSmile

60.

If you forget the password, you must initialize Holux GPSmile 60 (for
more information, see “Clearing Memory” on page 48). Please note that
when the initialization is performed, data or settings stored in Holux
GPSmile 60 are all deleted.

> Settings. On the Personal tab, tap Password.

- 36 -

Chapter 3: Microsoft ActiveSync

Chapter 3:

Microsof t ActiveSync

Using ActiveSync, you can synchronize information between Holux
GPSmile 60 and your PC or server. Synchronization compares the data on
Holux GPSmile 60 with the data residing on your PC and updates both with
the most recent information. For example:

• Keep Pocket Outlook data up-to-date by synchronizing Holux GPSmile

60 with Microsoft Outlook data on your PC.

• Synchronize Microsoft Word and Microsoft Excel files between Holux

GPSmile 60 and your PC.

Your files are automatically converted to the correct format.

CAUTION

ActiveSync does not automatically synchronize all types of
information. Use ActiveSync options to turn
synchronization on and off for specific information types.

With ActiveSync, you can also:

• Change synchronization settings and synchronization schedule.

• Copy files between Holux GPSmile 60 and PC.

• Back up and restore Holux GPSmile 60 information.

• Add and remove programs on Holux GPSmile 60.

Before synchronizing, confirm that ActiveSync version 3.7.1 or later is
installed on your PC. You can install ActiveSync 3.7.1 from Holux GPSmile
60 Companion CD.

After the installation is complete, the ActiveSync Setup Wizard helps you
connect and synchronize information between Holux GPSmile 60 and your
PC, and customize your synchronization settings. Your first synchronization
process begins when you finish using the wizard.

- 37 -

Chapter 3: Microsoft ActiveSync

After your first synchronization, take a look at Calendar, Contacts, and Tasks
on Holux GPSmile 60. The information you stored in Microsoft Outlook on
your PC has been copied to Holux GPSmile 60, and you did not have to type
a word. Disconnect Holux GPSmile 60 from your PC and you are ready to
go!

- 38 -

Chapter 3: Microsoft ActiveSync

Once you have set up ActiveSync and completed the first synchronization
process, you can initiate synchronization from Holux GPSmile 60. To switch
to ActiveSync, tap

> Programs > ActiveSync.

For information about using ActiveSync on your PC, start ActiveSync on
your PC and then see ActiveSync Help.

For more information about ActiveSync on Holux GPSmile 60, switch to
ActiveSync, tap

> Help.

View connection status.

Tap to connect and

synchronize.

Tap to synchronize

via IR or change

synchronization settings.

Tap to stop
synchronization.

Changing the Synchronization Schedule

Using ActiveSync, you can schedule the synchronization of Holux GPSmile
60 on two separate schedules.

• Use the peak times schedule to synchronize during working hours or

other times you experience higher mail volumes.

• Use the off-peak schedule to synchronize during times when you

experience lower mail volumes.

- 39 -

Chapter 3: Microsoft ActiveSync

In ActiveSync on Holux GPSmile 60, tap Tools > Options > the Mobile
Schedule tab.

1. To synchronize periodically during peak times, select the frequency of

synchronization in the Peak times list.

2. To synchronize periodically during off-peak times, select the frequency

of synchronization in the Off-peak times list.

3. To set the days and hours for peak times, tap Peak Times.

- 40 -

Chapter 4: GPS Function

Chapter 4:

GPS Function

Holux GPSmile 60 is also a global positioning system (GPS) device. It is a
very convenient tool for navigation on the road.

Note:

Please set your GPS before getting on the road. No setting while driving.
The actual procedures will depend on the map source which the end users

1. There are two ways to install Map AP. One way is to have Map AP start
installation automatically after cold boot. The second way is to install from CD.

2. After installation, if Program button 2 (refer to p17) is programmed to start Map
AP, press down Program button 2 will start Map AP. On the other hand, if the
programming was not done, press down Program button 2 will open “Welcome to
GPS world!” screen.

3. If Program button 2 (refer to p17) is not programmed to start Map AP, please
select

2 and select the Map AP to be programmed. Finally click OK button to complete the
programming. After programming is done, press down Program button 2 will start
Map AP.

>Settings> Personal > Buttons > Program buttons, then select button

- 41 -

Chapter 4: GPS Function

4. To close Map AP, just use the close method of Map AP

Start Map AP is not going to start GPS Power. Close Map AP will not close GPS
Power either. User has to start/close GPS independently from Map AP.

Methods for starting/closing GPS Power

1. Click GPS icon located at the lower right corner of Today screen to start/close
GPS Power.

2.

GPS Power On GPS Power Off

3. Select > Settings > System > GPS Power Control, press down Power button

to start/close GPS Power.

4.

- 42 -

Chapter 4: GPS Function

Zoom in and Zoom out

When turn on map program, the program will automatically enter the main

screen. Then the buttons of Zoom-in and Zoom-out can work to the map.

z Zoom-in button :

Press Zoom-in button will enlarge the map display.

z Zoom-out button :

Press Zoom-out button will diminish the map display.

NOTE

The zoom in/ zoom out depending on whether your map
support or not.

Using GPS Power Control

To view GPS power control, tap > Setings > System > GPS

power control.

GPS Power Control is used to configure the GPS settings.

Below are the main screen and setting items of GPS Power Control.

- 43 -

Chapter 4: GPS Function

• POWER

This item indicates that GPS is enabled (the button appears highlighted)
or disabled.

• Reset GPS

When the positioning fails within 10 minutes at the same spot with a
clear view of the sky, pressing this button returns to the normal status.

NOTE

Execution parameters are used to add parameters for the

selected map program. It is not absolutely required to set
parameters.

Set Environment Profile:

Environment Profile can let you quickly adjust Screen light, Speaker/
Microphone and Headphone to fit in with different weather condition and
usage environment.

For example:

1. Tap Profile on Today

2. Normal chose, Tap Setting

- 44 -

Chapter 4: GPS Function

3. Adjust Screen light, Speaker/ Microphone, Headphone and Name by

your requirement.

- 45 -

Chapter 5: Additional Information

Chapter 5:

Additional Information

Troubleshooting

Check the following table for the possible cause of the problem and how to
correct it.

Symptom Cause Correction

is pressed, the power
does not turn on.

cut off.

The touch screen was
tapped, but the correct
action was not performed.

The operation is slow in
response.

The battery
power is
exhausted.

The main battery
is not installed.

The battery
power is
exhausted.

Automatic
suspend is
active.

The touch screen
adjustment is
incorrect.

Insufficient
memory

Some
malfunction

Charge the battery. Even if the power button

Install the main battery.

Charge the battery. The power was suddenly

Tap

System > Power to change

the power shutdown time.

Tap > Settings >

System > Screen > Align
Screen to adjust the touch

screen.

Secure the free memory.
Quit the application if it is
not in use.

Reset the device. If no
action is observed after
resetting the device,
initialize the device.
(However, the data will be
deleted.)

> Settings >

- 46 -

Chapter 5: Additional Information

Symptom Cause Correction

The screen was tapped,
but there is no response.
The operation button
does not work, either.

The screen is dark. The screen light

The screen is hard to see. The brightness

Cannot connect to your
PC.

ActiveSync does not
function when Holux
GPSmile 60 is connected
to your PC with a USB
cable.

Cannot access the
Internet.

Some
malfunction

is off.

setting is
incorrect.

— See ActiveSync Help.

The USB driver
on your PC may
not be
compatible.

The
communication
settings are
incorrect.

Reset the device. If no
action is observed after
resetting the device,
initialize the device.
(However, the data will be
deleted.)

Press and hold the power
button until the screen light
is turned on.

Tap > Settings >
System > Screen light to

adjust the screen
brightness for better sight.

Re-select the USB driver.

Carry out correct settings.

Resetting

Resetting is equivalent to restarting a PC. Reset Holux GPSmile 60 when a
button or tapping the screen does not respond. When Holux GPSmile 60 is
reset, all data that was not stored during operation is deleted.

NOTE

When the power is on, use the stylus to press and hold the reset switch, and
then release it.

- 47 -

If the functionality cannot be restored even if the reset
switch is pressed, initialize Holux GPSmile 60. See
“Clearing Memory” on page 44.

Chapter 5: Additional Information

Clearing Memory

When you initialize Holux GPSmile 60, it returns to the status when it was
purchased.

CAUTION

1. Turn off Holux GPSmile 60.

2. Press and hold the power buttons,

button 4(p17),

back side of Holux GPSmile 60.

3. Release the Power buttons.

4. When a screen appears, release the reset switch. When the initialization
is complete, the Welcome screen appears.

5. Follow the on-screen instructions to set up the device.

When you initialize Holux GPSmile 60, all data stored in the
memory is deleted. Holux GPSmile 60’s initially installed
programs are not deleted.

Before the initialization, remove the SD card.

Program button 3 (p17) and Program

meanwhile, use the stylus to press the reset switch on the

Specifications

Item Description

External dimensions
(L x W x H)

Weight
Operating conditions

Approximately
(121 x 71.8 x 17~22 mm)

Approx. 160 +/- 5g

- 48 -

Item Description

Temperature
Relative humidity

Storage conditions

Temperature
Relative humidity

Battery type

Processor
Memory
Flash ROM
Display

Interfaces

DC-IN
Headphone
Microphone
Speaker
USB Client port
SD card slot

Chapter 5: Additional Information

32°F ~ 104°F (0°C ~ 40°C)

10% ~ 85%

-4°F ~ 140°F (-20°C ~ 60°C)

10% ~ 85%

1320mAh, removable, rechargeable
Lithium-Ion battery

Intel® bulverde PXA270 312/416 MHz

64 MB

64 MB

3.5” diagonal, TFT color LCD screen, 240 x
320 pixels, up to 64K colors,0.244 mm dot
pitch,6 LED Backlight.

5V/1A

3.5 mm, stereo, mini-plug compatible

Built-in, highly sensitive microphone

Built-in, 0.5W mono speaker

USB Client compliant with USB v1.1

SD memory card, SD I/O card or Multimedia
card
The security function of the SD memory card is
disabled. Data encrypted by the SD memory
card security function compatible equipment is
not usable.

- 49 -

Chapter 5: Additional Information

Infrared port

Based on IrDA ver. 1.3
Maximum data transmission speed: 115 kbps

Audio

AC 97 codec
Mono record
Stereo playback, 8.0 KHz, 11.025 KHz, 22.05
KHz, and 44.1 KHz sample rate
Full duplex for simultaneous record and
playback
On-board microphone
On-board speaker
Stereo earphone/microphone jack
Software volume control

Hardware (volume button) & Software volume
control.

GPS Receiver

Receiver

GPS signal: L1, C/A code
Channel: 12 channels
Tracking sensitivity: -152dBm

Acquisition time

< T ypical >

Hot start: 8 sec
Warm start: 38 sec
Cold start: 42 sec
Update: 1 sec

Accuracy position

25M (95%) CEP (without WAAS or DGPS)
1~5M (95%) CEP (with WAAS or DGPS)

Protocol support

NMEA 0183 (GGA, GLL, GSA, RMC, VTG)
Baud rate 4,800 bps
COM 2 1.5896(2(p14() )]TJET32.64 521.209 334.2 0.48 refBT/TT6 1 Tf10.02 0 0 10.02 38172 286.8487 Tm-0.0019 Tc-1.0025Twpimumaxidio )Tj/TT2 1 Tf11.8503 0.006 TD-0.0001 Tc0 WGS- 36w( )TjET32183 297.169 334.2 8001 refBT/TT6 1 Tf10.02 0 0 10.02 38157 286.8487 Tm-0.0003 Tc-0.0021 TD)-(y)1(ra6(a)namiclumed posistion )]TJ/TT2 1 Tf11.9222 0.006 TD-0.0006 Tc-0.0018(Altitudpdat8,-0 M6w( ]TJ0 -1.1437 TD0.0002 Tc-0.0026 TV)56 2 e.5(n)-locitivi51.0ithM/s( spe)cjack )]TJ0 -1.1557 TD-0.0007 Tc-0.0017 Tw[eleaudosi: 4G m[(Maxith4() )]TJET32168 297.169 334.2 8001 refBT/TT6 1 Tf10.02 0 0 10.02 31CEP884.3687 TD0.000400024 Tw[(Ac)-3ss(Ac)-ories(Ac)-.1(r )]TJ/TT2 1 Tf12.1138 0.006 Tc-0.0003 Tc-11.002 Tw[44.)3.6(1(yluHot cc), battery(CO9yb)4.-a)6.ot cce Syncot ccc

- 50 -