Item # _____________________________________
Quantity ___________________________________
C.S.I. Section 11400
CLPS86eR
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
STANDARD FEATURES
■ Energy recovery
■ 22 inch power scrapper with 2 HP motor
■ 342 racks per hour
■ Opti-RinSe™ system
■ 30 KW electric booster heater
■ Rapid return conveyor drive mechanism
■ Insulated hinged double doors with door
interlock switches
■ Door seal system
■ Pressure regulating valves
■ 19.5 inch chamber height opening
■ Top mounted micro-processer control module
■ Energy saver mode
■ Dirty water indicator
■ Low temperature alert
■ Conveyor dwell
■ Delime notication
■ Service diagnostics
■ NAFEM Data Protocol compliant
■ Computational uid dynamic designed self-
aligning wash manifolds
■ Stainless steel debossed anti-clogging wash
arms
■ Removable integrated pump intake screen
■ Stainless steel self-draining pumps and impellers
■ Single, sloping scrap screen and deep basket
■ Stainless panels enclose perimeter and bottom
■ Door actuated drain closure
■ Single point electrical connection (does not
include the booster heater)
■ Vent fan control
DISHWASHER
MODEL
❑ CLPS86e – Dishwasher
OPTIONS AT EXTRA COST
❑ Single point electrical connection, to include
electric booster – three phase only
❑ Higher than standard chamber
ACCESSORIES
❑ Stainless steel vent hoods (load end only)
❑ Canopy exhaust power vent kit
❑ Direct drive unloader
❑ Side loader
❑ Blower-dryer
❑ Drain water tempering kit
Specications, Details and Dimensions on Inside and Back.
CLPS86eR DISHWASHER
DIRECTION OF OPERATION
❑ Right to Left
❑ Left to Right
VOLTAG E
❑ 208/60/3 ❑ 240/60/3 ❑ 380/60/3
❑ 480/60/3 ❑ 600/60/3
F40300 – CLPS86eR Dishwasher Page 1 of 12
Shown with optional vent hood at load
CLPS86eR
DISHWASHER
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
THE CLeR WAREWASHER IS STANDARD WITH THESE EFFICIENT FEATURES . . .
Inside and out the CLeR warewashers by Hobart are packed with standard components and design innovations
that make them the biggest value in the dishwasher industry.
The Energy Recovery
System captures
escaping heat and
steam from the
exhaust air and uses
a heat exchanger to
recycle it into energy.
This free energy is
used to preheat the
incoming water supply
before it enters the
booster heater. The
ground temperature
water passes through
The insulated hinged inspection doors provide easy
access in the chamber. Exterior wash pipes and
reduced interior bafes reduce clean-up time.
The Rapid Return drive allows for a wide separation
between the wash and the rinse zone.
a heat exchanger
positioned directly in
line with the machine’s
unload exhaust system
to capture the energy
from the exhaust air and ware leaving the machine to
elevate the temperature of the water to 110° before it
enters the booster heater.
The Hobart exclusive microprocessor control module
offers a choice of many features, such as an exclusive
Energy Saver Mode, Low Temperature Alerts, and
Dirty Water Indicator. It also displays pertinent
machine status and has a Delime Notication. The
controls have built-in Service Diagnostics and are
NAFEM Data Protocol Compliant.
Wash Manifolds. Computational Fluid Dynamic
designed wash manifolds are self-aligning and come
with Hobart’s signature debossed anti-clogging
nozzles for superior result.
Opti-RinSe™. Hobart’s exclusive Opti-RinSe™
signicantly reduces operating cost by reducing rinse
water and the energy required to heat the water.
The unique spray pattern uses large droplets to more
efciently sanitize the ware.
Built-in Pressureless Stainless Steel Booster Heater.
Interwired and interplumbed. Saves on installation and
saves oor space. Simplies operation with just one
switch to power dishmachine and booster.
Page 2 of 12 F40300 – CLPS86eR Dishwasher
CLPS86eR
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
OTHER STANDARD FEATURES . . .
• Thermal Layer Curtains help keep the heat inside
the machine.
• Ball Detent Clutch Conveyor Drive for maximum
protection against conveyor jams
• Integrated Removable Pump Intake Screen to
offer the ultimate guard of keeping debris from
entering the pump.
• Hinged Door Seals and stainless steel labyrinth
seal for drip-free operation
• Door Actuated Drain Closure. Closing the door
automatically actuates drain closure, eliminates
extra manual steps, ensures that closure is in the
correct position.
AVAILABLE OPTIONS AND ACCESSORIES . . .
Flexibility is synonymous with Hobart CLeR dishwash ers. If your operation demands a dishwasher
with a vent hood, an extended hood . . . a power
scrapper, just specify the combination of options that
suit your needs.
Side Loader. Save up to 20 square feet in the
dishroom layout with an optional CLeR Side Loader.
Racks are indexed 90° into the dishwasher automatically – a feature that cuts space and reduces labor
dramatically. Your dishroom team will appreciate this
feature.
OTHER AVAILABLE ACCESSORIES . . .
Blower-dryer, direct drive unloader.
Machine Ratings (Mechanical)
Racks per hour (193⁄4" x 193⁄4") 342
Conveyor Speed - feet per minute 9.5 max.
Dishes per Hour (Average 25 per rack) 8,550
Glasses per Hour (Average 45 per rack) 15,390
Floor Space – Table to Table (Inches) 86
Overall Dimensions – H x W x D (Inches) 799⁄16 x 993⁄4 x 311⁄4
Motor H.P. Power Scrapper 2
Conveyor Drive H.P.
Number of Tanks 3
Tank Capacity – Gallons Power Scrapper 23
Pump Capacity –
Gallons per Minute - Weir Test Combined 435
Heating Equipment –
(For keeping wash/power rinse hot)
Gas Burners (with Natural Gas/LP)
Electric Heating Unit – Size Used Regulated 25 KW (15-10)
Booster Heater / Final Rinse 30 KW
Rinse – Minutes operated during hour of
maximum operation 60
Final Rinse Flow – Gals. per min.
At 15 PSI Flow Pressure 1.89
At 20 PSI Flow Pressure 2.2
Final Rinse Flow – Gals. per hr. – MAXIMUM
At 15 PSI Flow Pressure 114
At 20 PSI Flow Pressure 132
Rinse 20 PSI Flow Pressure
Gal./Rack
Steam Consumption –
Pounds per hr. - MAXIMUM
Approx. 30 lbs. per hr. = 1 boiler H.P. (BHP)
Dishwasher, based on 20 PSI steam and
on customer supplying final rinse water
at 180°F maximum 130
Steam Booster, if used on 20 PSI steam 20 PSI water flowing - 130°F entering
water raised to 180°F min. 63
Exhaust Requirements –
Cubic Feet per minute
Peak Rate of Drain Flow – Gallons per minute.
(Initial rate with full tank) 38
Shipping Weight Crated – Approximate lbs. 1127
DISHWASHER
CLPS86e
Wash 2 – Rinse 2
1
⁄6
Wash 23 – Rinse 22
156,000 BTU per hr.
(2 - 78,000)
Hot Water Sanitizing
.39 - 180°F
Entrance End 200
Discharge End 175
F40300 – CLPS86eR Dishwasher Page 3 of 12
CLPS86eR
DISHWASHER
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 4 of 12 F40300 – CLPS86eR Dishwasher
CLPS86eR
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
DISHWASHER
F40300 – CLPS86eR Dishwasher Page 5 of 12
CLPS86eR
ELECTRIC L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 6 of 12 F40300 – CLPS86eR Dishwasher
CLPS86eR
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
ELECTRIC R-L
F40300 – CLPS86eR Dishwasher Page 7 of 12
CLPS86eR
GAS L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 8 of 12 F40300 – CLPS86eR Dishwasher
CLPS86eR
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
GAS R-L
F40300 – CLPS86eR Dishwasher Page 9 of 12
CLPS86eR
STEAM L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 10 of 12 F40300 – CLPS86eR Dishwasher
CLPS86eR
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
STEAM R-L
F40300 – CLPS86eR Dishwasher Page 11 of 12
CLPS86eR
DISHWASHER
SPECIFICATIONS: Meets requirements of A.S.S.E. Standard No.
1004.
DESIGN: Semi automatic, high temperature double-tank, racktype dishwasher with exible thermal layer curtains at the ends of
chamber and between prewash, wash, rinse and nal rinse zones.
Insulated hinged inspection doors located in front of machine
provide easy access to wash arms, rinse arms, strainer, strainer
basket, and pump intake screen. Length of machine inside tank (at
table connection) 86". Machine designed to clean and sanitize with
hot water 160°F wash, 160° power rinse and 180°F (minimum) nal
rinse. Water hardness recommended to be 3 gr. for best results.
Automatic interlocks shut off pump and conveyor if door is opened
when machine is in operation.
CONSTRUCTION: Tanks, chambers, frame, legs, control box,
doors, and all panels are constructed of stainless steel.
PUMP: Three recirculating stainless steel pumps and impellers
with ceramic seat seals. Easily accessible pump assembly permits
quick inspection. The pumps are self-draining. All piping distributing water to the upper and lower wash arms is stainless steel
tubing.
PUMP MOTOR: Built for Hobart 2 hp grease-packed ball bearings,
splash proof, ventilated with manual, resettable inherent overload
protection. Available in electrical specications of 208-240/60/3,
480/60/3 and 600/60/3. Also available, but not submitted for
UL listing are 200-240/50/3 and 380-415/50/3.
ENERGY RECOVERY COIL: The condensing system using a
tube and n coil constructed of copper and corrosion resistant
aluminum.
CONTROLS: A stainless steel control module with power and
“start/stop” buttons is mounted on top of the machine. Machine
control circuitry will be operated from a 120-volt control circuit
transformer. Electrical components are completely wired with
105°C, 600V thermoplastic insulated wire with stranded conductors routed through UL listed electrical conduit or covered wire
way.
CONVEYOR: Rapid Return drive, designed for more even throughput of racks and allows for an 18.75-inch sepa ration between the
wash and the rinse zone. Racks conveyed automatically through
wash and rinse zones. Ball Detent Clutch drive prevents damage
to machine or racks, should movement of racks be obstructed.
Conveyor speed: 9.5 FPM.
DRIVE MOTOR: Built for Hobart, 1⁄6 horsepower gear motor,
ventilated with manual, resettable inherent overload protection.
Available in electrical specications of 208-240/60/3, 480/60/3
and 600/60/3. Also available, but not submitted for UL Listing are
200-240/50/3 and 380-415/50/3.
POWER SCRAPPER: CLPS86eR power scrapper is equipped
with an upper and lower wash arm with specially shaped nozzles
having large openings and arranged to effectively scrap all
types of tableware. Power scrapper arms and end caps are
easily removable for cleaning without use of tools. Removable
perforated stainless steel strainer pans support a deep perforated
stainless steel basket. Basket and strainer pans (3) can be
removed without lower wash arm removal.
POWER WASH AND RINSE: Wash and rinse tanks are equipped
with upper and lower stainless steel CFD Wash Arms which
effectively direct water jets to all ware surfaces. Both upper and
lower wash arms are self-aligning and have easily removable end
caps for cleaning without use of tools. A removable perforated
stainless steel strainer pan supports a deep perforated stainless
steel basket.
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
FINAL RINSE: Final rinse ow rate: 2.2 gpm, .39 gpr, 132-gph.
Stainless steel upper and lower Auto Position Rinse Arms™ have
single rows of nozzles. Racks entering the rinse zone automatically
trigger rinse. Final rinse water line is equipped with a vacuum
breaker downstream of an electrically operated solenoid valve
in common piping system. Rinse agent dispenser injection ports
provided in nal rinse piping above chamber.
FILL: Fill water line is equipped with vacuum breaker on downstream side of electrically operated solenoid valve in common
piping system, for automatic maintenance of tank level.
DRAIN AND OVERFLOW: Large bell-type automatic overow and
drain valve controlled from inside of machine. Power scrapper
overows to drain. Wash tank drain controlled from inside of the
machine overows to power scrapper through large internally
mounted stainless steel tubing. Drain seals are large diameter
high temperature o-rings. Drain automatically seats by closing
inspection doors. Common drain utilizes a removable large
diameter stainless steel tube sealed by rubber o-rings at each drain
housing. Drain housing can be plumbed from load or unload end of
machine.
STANDARD EQUIPMENT: Energy Recovery, Digital display of
power scrapper, wash and nal rinse temperature. Positive low
water protection for tank heat. Thermal Layered Curtains throughout machine are keyed to ensure proper placement. Drains are
automatically closed when inspection doors are closed. Stainless
steel adjustable feet. Bolted stainless steel enclosure panels
around perimeter and underneath machine. Automatic tank ll.
Door interlock. Auto-timer. Vent fan and booster heater controls.
Single point electrical connection. Low temperature alerts. Service
diagnostics. Dirty water indicator. Delime notication. Conveyor
dwell. Energy Saver Mode. NAFEM Data Protocol compliant.
Pressure regulating valve. Booster heater (30 kw).
WASH TANK HEATING SELECTIONS (must choose one):
ELECTRIC: Two electric Incoloy® sheathed immersion heaters
(15 KW and 10 KW) removable from inside tank. Tank water temperature is controlled by microprocessor controlled thermostat with
positive low-water protection and magnetic contactor. (Disconnect
switches not furnished.) A high limit device mounted on the surface
of the tank additionally protects heating element.
STEAM: One-inch stainless steel steam coil. Tank water
temperature controlled by microprocessor controlled thermostat
with positive low-water protection. Steam supplied to machine
through high temperature steam solenoid valve and line strainer.
GAS: Regulated infrared immersion tube gas burner system.
Microprocessor controlled thermostat and a blower with a pressure
switch control tank water temperature. Positive low water protection is provided. A high limit device mounted on the surface of the
tube additionally protects immersion tube. A solid-state igniter
board controls the gas valve and provides ame ignition. A transformer steps the control circuit voltage down from 120 volts to 24
volts to power the igniter board and gas valve. For natural gas, gas
pressure to burner (customer connection) not to exceed 7" W.C.
For LP gas, gas pressure to burner (customer connection) not to
exceed 11" W.C. If gas pressure is higher than 7" W.C. natural or
11" W.C. LP pressure regulating valve must be supplied (by others)
in the gas line to the dishwasher.
OPTIONAL EQUIPMENT AT EXTRA COST:
Stainless steel vent hoods with vent stack, and locking-type
damper (load end only). Canopy exhaust power vent kit. Higher
than standard chamber. Side loaders and unloaders. 193⁄4" x 193⁄4"
peg, combination and miscel laneous racks. Table limit switch.
Drain water-tempering kit.
As continued product improvement is a policy of Hobart, specications are subject to change without notice.
Page 12 of 12 F40300 – CLPS86eR Dishwasher
F40300 (REV. 10/14) LITHO IN U.S.A. (H-01)
Loading...