SAFETY INFORMATION
EMERGENCY DOOR OPENING
INSTALLATION GUIDE
SAFETY INFORMATION
1.
The manufacturer reserves the right for any modifications
on the product which might be deemed necessary or
useful without informing about it in this IFU.
2.
Before operating your new washing machine, please read
this instruction carefully, and keep it for future reference. If
you have lost it accidentally, ask customer service for e-
copy or hard copy.
3.
Please make sure the socket is grounded securely, the
water source connection is reliable.
4. This appliance is not to be used by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
This appliance can be used by children aged from 8
5.
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
6.
Children should be supervised to ensure that they do not
play with the appliance.
7.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
8.
The new hose-sets supplied with the appliance are to be
used and that old hose-sets should not be reused.
1
9.
For appliances with ventilation openings in the base, that a
carpet must not obstruct the openings.
10.
Children of less than 3 years should be kept away unless
continuously supervised.
11.
The maximum permissible inlet water pressure, 1 MPa, for
appliances intended to be connected to the water mains.
The minimum permissible inlet water pressure, 0.1 MPa, if
this is necessary for the correct operation of the appliance.
12.
The maximum washing capacity is 7.5/8.5
For private domestic use only.
13.
/9.5/10kg.
14.
2
ensure
2. Remove transport bolts
Important: Transport bolts which are not removed can cause damage to
the appliance.
Screw off all transportation bolts for approx. 30mm with wrench following the
direction of arrow shown (not fully screw it off).
30
Push four transportation bolts on horizontal direction inward and loose
transportation bolt.
3
Pull out transportation bolt together with rubber part and plastic part.
To ensure safety and reduce noise, you should install the transportation bolt
cover supplied with the unit (see the annex accompanying the unit). Lean
and place the transportation bolt into hole and press it following the shown
direction until it clicks.
Adjustment of the feet
3.
The appli
ance must be installed on a solid and level floor surface (if necessry
use a spirit level). If the appliance is to be installed on a wooden floor, distribute
the weight by placing it on a 60x60cm sheet of plywood at least 3cm in
thickness and secure it to the floor. If the floor is uneven, adjust the 4 leveling
feet
as required; do not insert pieces of wood etc. under the feet.
4
4. Install bottom cover
To realize quieter operation, a bottom cover is supplied with the unit (only
applies to some of the Hisense washers). After installing the cover at the
bottom of the washer, the noise level will be greatly reduced. Please ask
for advice from specialists before installing the cover, nevertheless, the
machine can be used without the bottom cover.
Noise-Reduction Bottom Plate Installation Instructions
A:
Stick acoustic wool to the side of bottom cover plate
with the letter of “PUMP”.
Tilt the washer by 30°-40°, when installing the bottom
cover, please face the side with sound insulation
upwards and attach 'PUMP' at the corner of the cover
to the position of the pump in the washer.
PUMP
PUMP
5
B:
Right-angle impression
Before installing the noise-reduction bottom
plate, align and paste the acoustic absorption
wool with and along the right-angle impression
on bottom plate (this procedure is unnecessary
for some of the models without acoustic
absorption wool).
Incline the machine to an angle of 40° and let
the side with right-angle notch face towards
front of the washing machine, as shown in the
figure. Insert the side with oblique-angle notch
Pump
between two foot screws at back of the
washing machine completely in place. Then,
install the bottom plate and ensure that it
contacts with bottom of the washing machine
closely.
Remove surface paper on
double sided tape at four sides
of the bottom plate.
Double sided tape
Press the double sided tape
on four sides manually to
secure the noise-reduction
palte to the machine body
firmly.
5. Connect the water supply inlet hose
If the water inlet hose is not already installed, it must be screwed to the
appliance.The blue marked hose is only for cold water. Depending on the model,
the hot water hose marked with red should also be connected, for models having
dual inlets.
6
Loading...