Hilti SD2500, SD4500 User Manual

SD4500 / SD2500
*285702*
285702
Operating instructions en Mode d’emploi fr Manual de instrucciones es Manual de instruções pt
2
2
3
1
3
1
3
2
4
6
1
2
5
2
7
2
1
2
1
Click
8
1
4
2
3
8
1
4
2
3
1
en
It is essential that the operating instructions are read before the tool is operated for the first time.
Always keep these operating instructions with the tool.
Ensure that the operating instructions are with the tool when it is given to other persons.
SD 4500 / SD 2500 drywall screwdrivers
1. General information
1.1 Safety notices and their meaning
-CAUTION-
Draws attention to a potentially dangerous situation that could lead to minor personal injury or damage to the equipment or other property.
-NOTE-
Draws attention to instructions and other useful infor­mation.
1.2 Pictograms
Contents Page
1. General information 1
2. Description 2
3. Tools and accessories 3
4. Technical data 3
5. Safety rules 4
6. Before use 5
7. Operation 6
8. Care and maintenance 7
9. Disposal 7
10. Manufacturer's warranty – tools 7
Operating controls and parts
1
/4″ chuck (for bit holder, magazine bit)
Adjustable depth gauge (with bit change function)Tool / accessory interface (click connection)Coupling system / gearingMotorBelt hookMotor cooling air intakeLockbutton for sustained operationSupply cordOn / off switch (with electronic speed control)Forward / reverse switchType plateCooling air exit with controlled air flow
These numbers refer to the corresponding illustra­tions. The illustrations can be found on the fold-out cover pages. Keep these pages open while studying the oper­ating instructions. In these operating instructions, the SD 4500 and / or SD 2500 screwdriver is referred to as « the power tool».
Location of identification data on the power tool
The type designation can be found on the rating plate and the serial number on the side of the motor housing. Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department.
Type:
Serial No.:
Warning signs
Obligation signs
Wear eye
protection
Read the operating
instructions before use.
Symbols
General warning
Warning: electricity
Return waste
material for
recycling
2.2 Main applications
Items supplied as standard with the SD 4500
– Power tool – Depth gauge – Belt hook – S-BH 75 M bit holder, S-B PH2 DRY bit – Operating instructions – Cardboard box
Application
Fastening drywall panels to metal profiles (track) 0.88 mm/ 20 ga
Fastening drywall panels to metal profiles (track)2.25 mm/25–16 ga
Fastening metal profiles to metal profiles (max. total thickness
2.5 mm /13–12 ga) Fastening drywall panels to wood
Fastening drywall panels to metal profiles (0.88 mm /20 ga) and wood frames
Fastening chipboard (particle board) to wood frames
Fastening: Wood to wood Wood to chipboard Chipboard to wood Screws up to 140 mm (51⁄2 in) in length
Fastening wood to metal Steel grade: ST 37 up to12 mm (
1
2 in)
Steel grade: ST 52 up to 8 mm (1⁄3 in)
2
en
2. Description
2.1 Use of the power tool as intended
The SD 4500 is a hand-held, corded power tool for pro- fessional use in the drywall installation trade.
The SD 2500 is a hand-held, corded power tool for pro- fessional use in the woodworking and drywall installa­tion trades.
These power tools are used for driving and removing the recommended types of screws in the correspond­ing materials of the specified thickness.
Screw type / diameter in mm
Needle-point drywall screws, type S-DS 01
Drill-point drywall screws, type S-DD 01
Special drywall screws with drill point, type S-DD 02 und S-DD 03
Needle-point drywall screws, type S-DS 03
Needle-point drywall screws, type S-DS 14
Needle-point drywall screws, Typ S-DS 03
Wood screws
Self-drilling wing screws with drill point, type S-WW
SD 4500
X
X
X
X
X
X
X
SD 2500
X
X
X
Items supplied as standard with the SD 2500
– Power tool – Depth gauge – Belt hook – S-BH 75 M bit holder, S-B PH2 DRY bit – Operating instructions – Cardboard box
The SD 4500 and SD 2500 are designed to be used in conjunction with a screw magazine (SMI 55 plus) and tool extension (SME) if desired. The power tools are intended for use on construction sites of all kinds for applications in the drywall installa­tion and woodworking trades. Only the specified screwdriving bits, magazine and accessories should be used with the power tools. The general safety precautions listed in the operating instructions must be observed.
3
en
4. Technical data
Tool
Rated power Rated voltage Rated current
Rated frequency Rated no-load running speed Chuck Weight of tool Dimensions
(L×W×H) Max. torque Speed control Forward / reverse
Protection class
Mechanical notch-type clutch Vibration-absorbing grip
SD 4500
740 W 120 V
6.5 A 60 Hz 0–4500 r.p.m.
1
/4DIN 3126 / ISO 1173
1.4 kg (3.1 Ibs) 290 ×75 ×160 / 168 mm
(11.4 ×2.9 ×6.3 / 6.6 in)
9.5 Nm (84 in-lbs) Electronic, by control switch Switch with interlock to prevent changing direction
while the motor is running Electrical protection class II Z (double insulated)
in accordance with UL/CSA60745 Electrical protection class I, grounded
(50 ft cord with Twist Lock Plug)
3. Insert tools and accessories
Belt hook Depth gauge Depth gauge Bit and bit holder
Magazine Extension
SD 4500
X X X X
X X
SD 2500
X X X X
X X
S-DG-D 11 x 50 for 50 mm (2") bit holder S-DG-D 11 x 75 for 75 mm (3") bit holder S-BH 75 M and S-BH 50 M bit holders, PH2, SQ and
TX bits SMI 55 plus SME extension for working on floors and ceilings
SD 2500
740 W 120 V
6.5 A 60 Hz 0–2500 r.p.m.
1
/4DIN 3126 / ISO 1173
1.5 kg (3.3 Ibs) 303 ×75 ×160 / 168 mm
(11.9 ×2.9 ×6.3 / 6.6 in) 19 Nm (168 in-lbs)
4
5.1 General safety rules
-WARNING-! Read all instructions! Failure to follow
all instructions listed below may result in electric shock, fire and / or serious injury. The term “power tool” in all of the warnings listed below refers to your mains oper­ated (corded) power tool or battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS.
5.1.1 Work area safety
a) Keep the work area clean and well lit. Cluttered and
dark areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable liq­uids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c)Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
5.1.2 Electrical safety
a) Power tool plugs must match the outlet. Never mod-
ify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of elec­tric shock.
b) Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges and refrig­erators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep the cord away from heat, oil, sharp edges or mov­ing parts. Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
5.1.3 Personal safety
a) Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use a power tool while you are tired or under the influ­ence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appro­priate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools
with your finger on the switch or plugging in power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jew-
ellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are connected and properly used. Use of these devices
can reduce dust related hazards.
5.1.4 Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
5.1.5 Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
en
5. Safety rules
5
en
6. Before use
-NOTE-
The voltage provided by the electric supply must cor­respond to the information given on the type plate on the power tool.
6.1 Using extension cords
Use only extension cords of a type approved for the
application and with conductors of adequate cross section. Failure to observe this point may cause the tool to loose power and the extension cord may over­heat. Check the extension cord for damage at regular intervals. Replace damaged extension cords.
5.2 Specific safety rules
a) Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with
a “live” wire will make exposed metal parts of the tool “live” and shock the operator.
-WARNING­To reduce the risk of injury, user must read instruction manual.
6.2 Use of a generator or transformer
This tool may be powered by a generator or transformer which fulfils the following conditions:
AC voltage, output power at least 2600 W.
The operating voltage must be within +5 % and –15 %
of the rated voltage at all times.
Frequency range 50–60 Hz; never above 65 Hz.
Automatic voltage regulation with starting boost.
Never operate other tools or appliances from the gen-
erator or transformer at the same time. Switching other tools or appliances on and off may cause under­voltage and / or overvoltage peaks, resulting in dam­age to the power tool.
Recommended minimum conductor cross section and max. extension cord lengths:
Mains voltage
Conductor cross section (mm
2
) 100 V 110–120 V 220–240 V
1.5
– 20 m 50 m
2.0
30 m 30 m
2.5
40 m
100 m
3.3
50 m 50 m
AWG
16
1.23
25 ft 50 ft
AWG
16
1.23
25 ft 50 ft
AWG
14
1.95
75 ft
100 ft
AWG
14
1.95
50 ft 75 ft
AWG
12
3.09
100 ft 150 ft
AWG
12
3.09
100 ft 125 ft
Conductor cross section 15 ft extension cord 50 ft extension cord
6
en
-CAUTION-
Secure the workpiece. Use clamps or a vice to hold the workpiece securely in position. It is then held more safely and both hands remain free for holding and oper­ating the tool.
7.1 Setting forward or reverse rotation
The forward / reverse switch is used to set the direction of rotation of the drive spindle. An interlock prevents operation of the switch while the motor is running. – Push the forward / reverse switch to the left (as seen
when the tool is in use) = forwards.
– Push the forward / reverse switch to the right (as seen
when the tool is in use) = reverse.
7.2 Switching on / off
1. Plug the supply cord into the power outlet.
2. Press the control switch slowly. This allows the user to select any speed between 0 and maximum.
-NOTE-
The drive spindle begins to rotate only when axial pres­sure is applied to the tool.
7.3 Lockbutton for sustained operation
The lockbutton for sustained operating mode allows continuous operation of the tool without need for apply­ing constant pressure to the control switch.
7.3.1 Switching on in sustained operating mode
1. Press the control switch as far as it will go and hold it in this position.
2. Press the lockbutton and then release the control switch.
7.3.2 Switching off after sustained operation
3. Press the control switch. The lockbutton returns to is its original position.
7.4 Interface for insert tools and accessories
1. Unplug the supply cord from the power outlet.
2. The depth gauge can be removed simply by pulling it away from the tool (click connection). The drive spin­dle is then exposed. The drive spindle must be exposed (depth gauge removed) for the following operations:
– Using the tool to remove screws (reverse rotation) – Changing bits – Changing the bit holder – Attaching the SMI 55 Plus magazine – Tightening / redriving existing screws
7. Operation
7.5 Adjusting the depth gauge
-NOTE-
By adjusting the depth gauge, the screw can be driven flush with the surface or left projecting. Each click-stop equals an adjustment of ± 0.25 mm (see illustration).
7.5.1 To drive the screw deeper
1. Turn the depth gauge to the right.
7.5.2 To drive the screw less deeply
2. Turn the depth gauge to the left.
7.6 Removing the depth gauge
1. Pull the depth gauge forward, away from the tool.
7.7 Changing insert tools
The chuck for holding insert tools (bit holder, bits etc.) is of the standard (DIN 3126 / ISO 1173)
1
/4″ hex. socket
type. The screwdriving insert tools are held in place by a spring mechanism.
1. Unplug the supply cord from the power outlet.
2. Remove the depth gauge by pulling it forward, away from the tool.
3. The insert tool can then be pulled out and changed (longer bit, bit holder, etc.).
4. Refit the depth gauge to the tool.
7.8 Removing a screw
Remove the depth gauge by pulling it forward, away from the tool. Set the forward / reverse switch to the reverse rotation position. The screw can then be removed.
7.9 Fitting / removing the belt hook
7.9.1 Fitting the belt hook
1. Insert the belt hook mounting lug in the ventilation slot on the tool.
2. Push the belt hook forward (toward the chuck).
3. Secure the belt hook with the retaining screw.
7.9.2 Removing the belt hook
1. Release the belt hook by removing the retaining screw.
2. Slide the belt hook back.
3. Pull the belt hook upwards out of the ventilation slot.
7
en
Unplug the supply cord form the power outlet.
8.1 Care of screwdriving bits and metal parts
Clean off dirt and dust deposits adhering to the surface of the screwdriving bits, chuck or spindle and protect these parts from corrosion by wiping them from time to time with an oil-soaked rag.
8.2 Care of the power tool
The outer casing of the tool is made from impact-resis­tant plastic. Sections of the grip are made from a syn­thetic rubber material. Never operate the power tool when the ventilation slots are blocked. Clean the ventilation slots carefully using a dry brush. Do not permit foreign objects to enter the interior of the power tool. Clean the outside of the power tool at regular intervals using a slightly damp cloth. Do not use a spray, steam pressure cleaning equipment or
8. Care and maintenance
running water for cleaning. This may negatively affect the electrical safety of the power tool. Always keep the grip surfaces of the power tool free from oil and grease. Do not use cleaning agents which contain silicone.
8.3 Maintenance
Check all external parts of the power tool for damage at regular intervals and check that all controls operate fault­lessly. Do not operate the power tool if parts are dam­aged or when the controls do not function faultlessly. If necessary, your power tool should be repaired at a Hilti repair center. Repairs to the electrical section of the power tool may be carried out only by trained electrical specialists.
8.4 Checks after care and maintenance
After carrying out care and maintenance, check the power tool for correct operation (drive and remove a screw).
9. Disposal
Most of the materials from which Hilti power tools are manufactured can be recycled. The materials must be cor­rectly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools for recycling. Please ask your Hilti customer service department or Hilti representative for further information.
10. Manufacturer's warranty – tools
Hilti warrants that the tool supplied is free of defects in material and workmanship. This warranty is valid so long as the tool is operated and handled correctly, cleaned and serviced properly and in accordance with the Hilti Operating Instructions, and the technical sys­tem is maintained. This means that only original Hilti consumables, components and spare parts may be used in the tool.
This warranty provides the free-of-charge repair or replacement of defective parts only over the entire lifes­pan of the tool. Parts requiring repair or replacement as a result of normal wear and tear are not covered by this warranty.
Additional claims are excluded, unless stringent national rules prohibit such exclusion. In particular,
Hilti is not obligated for direct, indirect, incidental or consequential damages, losses or expenses in connection with, or by reason of, the use of, or inabil­ity to use the tool for any purpose. Implied warranties of merchantability or fitness for a particular purpose are specifically excluded.
For repair or replacement, send tool or related parts immediately upon discovery of the defect to the address of the local Hilti marketing organization provided.
This constitutes Hilti's entire obligation with regard to warranty and supersedes all prior or contemporane­ous comments and oral or written agreements con­cerning warranties.
UL listed to US and Canadian safety standards
Homologué UL (conforme aux normes de sécurité américaines et canadiennes)
Producto homologado según normas de seguridad americanas y canadienses
Produto homologado de accordo com as normas de segurança americanas e canadianas
CUS
R
Hilti Corporation
FL-9494 Schaan Tel.: +423 /234 2111 Fax: +423 /234 29 65 www.hilti.com
Hilti = registered trademark of Hilti Corp., Schaan W 3080 0905 10-Pos. 3 1 Printed in China © 2005 Right of technical and programme changes reserved S. E. & O.
285702 / B
Loading...