Hilti DAG 230-D, DCG 230-D User Manual
Bedienungsanleitung de
Operating instructions en
Használati utasítás hu
Návod k obsluze cs
Návod na obsluhu sk
Instrukcja obsługi pl
Upute za uporabu hr
Navodila za uporabo sl
Ръководство за обслужване bg
Инструкция по зксплуатации ru
Пайдалану бойынша басшылық kk
Instrucţiuni de utilizare ro
Kulllanma Talimatı tr
zh
cn
DCG 230-D/
DAG 230-D
Printed: 20.11.2013 | Doc-Nr: PUB / 5139548 / 000 / 01
1
Printed: 20.11.2013 | Doc-Nr: PUB / 5139548 / 000 / 01
2
4
3
Printed: 20.11.2013 | Doc-Nr: PUB / 5139548 / 000 / 01
5
6
Printed: 20.11.2013 | Doc-Nr: PUB / 5139548 / 000 / 01
PP
PP
7
8
Printed: 20.11.2013 | Doc-Nr: PUB / 5139548 / 000 / 01
ORIGINAL OPERATING INSTRUCTIONS
DCG 230‑D / DAG 230‑D angle grinder
It is essential that the operating instructions
are read before the power tool is operated for
en
the first time.
Always keep these operating instructions together with the power tool.
Ensure that the operating instructions are
with the power tool when it is given to other
persons.
Contents Page
1 General information 16
2Description 17
3Consumables 19
4 Technical data 20
5 Safety instructions 21
6Beforeuse 25
7 Operation 26
8 Care and maintenance 28
9 Troubleshooting 28
10 Disposal 29
11 Manufacturer’s warranty - tools 29
12 EC declaration of conformity (original) 30
1 General information
1.1 Safety notices and their meaning
DANGER
Draws attention to imminent danger that will lead to
seriousbodilyinjuryorfatality.
WARNING
Draws attention to a potentially dangerous situation that
could lead to serious personal injury or fatality.
CAUTION
Draws attention to a potentially dangerous situation that
could lead to slight personal injury or damage to the
equipment or other property.
NOTE
Draws attention to an instruction or other useful information.
1 These numbers refer to the corresponding illustrations. The illustrations can be found on the fold-out cover
pages. Keep these pages open while studying the operating instructions.
In these operating instructions, the designation “the
power tool” always refers to the DCG 230‑D or
DAG 230‑D angle grinder.
Parts, operating controls and indicators 1
Clamping nut
@
“Kwik-Lock” clamping nut (optional)
;
Cutting disc
=
Clamping flange
%
Keying lug
&
Guard
(
Spindle
)
Adjusting screw
+
Clamping lever
§
Steadying rib
/
Threaded bushing for grip
:
Drive spindle lockbutton
·
Release lever (for pivotable grip)
$
Side handle
£
On / off switch (hold to run)
|
Wrench
¡
1.2 Explanation of the pictograms and other
information
Warning signs
General
warning
Warning:
electricity
16
Obligation signs
Wear eye
protection
Wear a hard
hat
Wear ear
protection
Wear
protective
gloves
Location of identification data on the power tool
The type designation and serial number can be found
on the type identification plate on the machine or tool.
Makeanoteofthisdatainyouroperatinginstructions
and always refer to it when making an enquiry to your
Hilti representative or service department.
Type:
Generation: 01
en
Wear
breathing
protection
Symbols
Serial no.:
Read the
operating
instructions
before use
Hertz Watts Alternating
Revolutions
per minute
Return waste
material for
recycling.
Revolutions
per minute
Volts Amps
current
Diameter Double
Rated speed
insulated
2 Description
2.1 Use of the product as directed
The power tool is designed for cutting and grinding metal and mineral materials without use of water.
Observe the information printed in the operating instructions concerning operation, care and maintenance.
Working with metals: Cutting, grinding.
Working with mineral materials: Cutting, slitting and grinding.
Use only discs (grinding discs, cutting discs, etc.) approved for use at a speed of at least 6500/min., with a thickness
of max. 8 mm and a diameter of max. 230 mm.
Use only synthetic resin-bonded, fiber-reinforced grinding discs or cutting discs approved for use at a permissible
peripheral speed of at least 80 m/sec.
To avoid the risk of injury, use only genuine Hilti accessories and insert tools.
Working on materials hazardous to the health (e.g. asbestos) is not permissible.
Nationally applicable industrial safety regulations must be observed.
Modification of the power tool or tampering with its parts is not permissible.
The power tool may be operated only when connected to a power supply providing a voltage and frequency in
compliance with the information given on its type identification plate.
The working environment may be as follows: construction site, workshop, renovation, conversion or new construction.
17
Loading...