Hilti DAG 100-S, DAG 115-S Operating Instructions Manual
DAG 100-S
ja
Operating instructions en
ko
zh
cn
Printed: 15.11.2013 | Doc-Nr: PUB / 5161758 / 000 / 00
1
Printed: 15.11.2013 | Doc-Nr: PUB / 5161758 / 000 / 00
2
5
4
3
Printed: 15.11.2013 | Doc-Nr: PUB / 5161758 / 000 / 00
ORIGINAL OPERATING INSTRUCTIONS
DAG 100‑S angle grinder
It is essential that the operating instructions
are read before the power tool is operated for
the first time.
Always keep these operating instructions together with the power tool.
Ensure that the operating instructions are
with the power tool when it is given to other
persons.
Contents Page
1 General information 15
2Description 16
3Consumables 18
4 Technical data 18
5 Safety instructions 18
6Beforeuse 22
7 Operation 24
8 Care and maintenance 25
9 Troubleshooting 25
10 Disposal 25
11 Manufacturer’s warranty - tools 26
1 These numbers refer to the corresponding illustrations. The illustrations can be found on the fold-out cover
pages. Keep these pages open while studying the operating instructions.
In these operating instructions, the designation “power
tool” always refers to the DAG 100-S angle grinder.
Operating controls and parts 1
Ventilation slots
@
On / off switch
;
Side handle
=
Spindle lockbutton
%
Spindle
&
Guard
(
Clamping flange
)
Disc
+
Clamping nut
§
Wrench
/
en
1 General information
1.1 Safety notices and their meaning
DANGER
Draws attention to imminent danger that will lead to
seriousbodilyinjuryorfatality.
WARNING
Draws attention to a potentially dangerous situation that
could lead to serious personal injury or fatality.
CAUTION
Draws attention to a potentially dangerous situation that
could lead to slight personal injury or damage to the
equipment or other property.
NOTE
Draws attention to an instruction or other useful information.
1.2 Explanation of the pictograms and other
information
Warning signs
General
warning
Warning:
electricity
Warning: hot
surface
15
Obligation signs
Wear eye
protection.
en
breathing
protection
Symbols
Wear
Wear a hard
hat
Wear ear
protection
Wear
protective
gloves
Location of identification data on the power tool
The type designation, item number, year of manufacture
and technical status can be found on the type identification plate on the machine or tool. The serial no. can
be found on the underside of the motor housing. Make
a note of this data in your operating instructions and
always refer to it when making an enquiry to your Hilti
representative or service department.
Type:
Generation: 02
Serial no.:
Read the
operating
instructions
before use
Watts Hertz Alternating
Revolutions
per minute
Return waste
material for
recycling.
Rated speed Diameter Double
Volts Amps
current
Revolutions
per minute
insulated
2 Description
2.1 Use of the product as directed
The power tool is designed for cutting and grinding metal and mineral materials without use of water.
The working environment may be as follows: construction site, workshop, renovation, conversion or new construction.
The power tool may be operated only when connected to a power supply providing a voltage and frequency in
compliance with the information given on its type identification plate.
Working with metals: Cutting, grinding.
Working with mineral materials: Cutting, slitting and grinding.
Use only discs (abrasive grinding discs, abrasive cutting discs, etc.) that are approved for use at a speed of at least
11000/min, with a maximum thickness of 6.4 mm (grinding discs) or 2.5 mm (cutting discs) and a diameter of max.100
mm.
Use only synthetic resin-bonded, fiber-reinforced grinding discs or cutting discs approved for use at a peripheral
speed of 80 m/sec or diamond cutting discs approved for use at a peripheral speed of 80 m/sec.
The power tool may be used only for dry cutting or grinding.
Cutting or grinding materials containing asbestos is not permissible.
Nationally applicable industrial safety regulations must be observed.
To avoid the risk of injury, use only genuine Hilti accessories and insert tools.
Observe the information printed in the operating instructions concerning operation, care and maintenance.
16
Loading...