Hikvision EPI-5225l-AE User Manual

Network Speed Dome Camera

EPI-5225l-AE

Quick Start Guide

Manual Illustrations and Features

Graphics (screen shots, product pictures, etc.) in this document are for illustrative
purposes only. Your actual product may differ in appearance. Your product might not
support all features discussed in this document.

Hikvision USA Inc., 18639 Railroad St., City of Industry, CA 91748, USA • Hikvision
Canada, 4848 rue Levy, Saint Laurent, Quebec, Canada, H4R 2P1

Telephone: [phone] • Toll Free in USA: [phone] • E-Mail:

[e-mail] • www.hikvision.com

COPYRIGHT ©2017-2018 Hangzhou Hikvision Digital Technology Co., Ltd.

ALL RIGHTS RESERVED.

Any and all information, including, among others, wordings, pictures, graphs are the
properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries
(hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be
“the Manual”) cannot be reproduced, changed, translated, or distributed, partially or
wholly, by any means, without the prior written permission of Hikvision. Unless
otherwise stipulated, Hikvision does not make any warranties, guarantees or
representations, express or implied, regarding to the Manual.

About this Manual

This Manual is applicable to the EPI-5225I-AE Network Speed Dome.

The Manual includes instructions for using and managing the product. Pictures, charts,
images and all other information hereinafter are for description and explanation only.
The information contained in the Manual is subject to change, without notice, due to
firmware updates or other reasons. Please find the latest version in the company Web
site (http://overseas.hikvision.com/en/).

Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement

and other Hikvision trademarks and logos are the properties of Hikvision
in various jurisdictions. Other trademarks and logos mentioned below are the properties
of their respective owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED,
WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS,” WITH ALL
FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,
FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN
NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE
LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION
WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.

QSG EPI-5225I-AE 030518NA 2

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE
WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR
ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM
CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY
RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN
YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR
USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW,
THE LATER PREVAILS.

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.

FCC Compliance: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may
cause undesired operation

EU Conformity Statement

This product and, if applicable, the supplied accessories too are marked
with “CE” and comply therefore with the applicable harmonized European
standards listed under the EMC Directive 2014/30/EU, the RoHS Directive
2011/65/EU.

2012/19/EU (WEEE Directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.

For more information see: www.recyclethis.info.

QSG EPI-5225I-AE 030518NA 3

2006/66/EC (Battery Directive): This product contains a battery that cannot
be disposed of as unsorted municipal waste in the European Union. See the
product documentation for specific battery information. The battery is

marked with this symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier
or to a designated collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Warning:

This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.

The precaution measure is divided into Warnings and Cautions:

Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.

Warnings Follow

these safeguards to
prevent serious
injury or death.

Cautions Follow these
precautions to prevent
potential injury or
material damage.

Warnings

 In the use of the product, you must be in strict compliance with the electrical safety

regulations of the nation and region.

 Refer to technical specifications for detailed information.
 Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited

Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Refer to
technical specifications for detailed information.

 Do not connect several devices to one power adapter as adapter overload may cause

over-heating or a fire hazard.

 Make sure that the plug is firmly connected to the power socket.

 Make sure that the power has been disconnected before you wire, install or dismantle

the speed dome.

 When the product is mounted on wall or ceiling, the device shall be firmly fixed.

QSG EPI-5225I-AE 030518NA 4

 If smoke, odor or noise rise from the device, turn off the power at once and unplug

the power cable, and then contact the service center.

 If the product does not work properly, contact your dealer or the nearest service

center. Never attempt to disassemble the speed dome yourself. (We shall not assume
any responsibility for problems caused by unauthorized repair or maintenance.)

Cautions

 If the speed dome fails to synchronize local time with that of the network, you need

to set up speed dome time manually. Visit the speed dome (via web browser or client
software) and enter system settings interface for time settings.

 Make sure the power supply voltage is correct before using the speed dome.

 Do not drop the speed dome or subject it to physical shock, and do not expose it to

high electromagnetism radiation. Avoid installation on vibrations surface or places
subject to shock (ignorance can cause device damage).

 Do not touch senor modules with fingers. If cleaning is necessary, use clean cloth with

a bit of ethanol and wipe it gently. If the speed dome will not be used for an extended
period, replace the lens cap to protect the sensor from dirt.

 Do not aim the speed dome at the sun or extra bright places. Blooming or smearing

may occur otherwise (which is not a malfunction), and affect the endurance of sensor
at the same time.

 The sensor may be burned out by a laser beam, so when any laser equipment is in

using, make sure that the surface of sensor will not be exposed to the laser beam.

 Do not place the speed dome in extremely hot, cold, dusty or damp locations, and do

not expose it to high electromagnetic radiation.

 To avoid heat accumulation, good ventilation is required for operating environment.
 Keep the speed dome away from liquid while in use.
 While in delivery, the speed dome shall be packed in its original packing, or packing of

the same texture.

 Improper use or replacement of the battery may result in hazard of explosion. Replace

with the same or equivalent type only. Dispose of used batteries according to the
instructions provided by the battery manufacturer.

QSG EPI-5225I-AE 030518NA 5

Table of Contents

1 Overview ...................................................................................................... 7

1.1 Speed Dome Overview .............................................................................................7

1.1.1 Overview of the EPI-5225I-AE (IR) Speed Dome .................................................7

1.2 Cable Interfaces ........................................................................................................7

2 Installation ................................................................................................... 8

2.1 EPI-5225I-AE (IR) Speed Dome Installation ...............................................................9

3 Speed Dome LAN Configuration ................................................................. 10

3.1 Wiring .....................................................................................................................10

3.2 Activating the Speed Dome ....................................................................................10

3.2.1 Activation via Web Browser .............................................................................11

3.2.2 Activation via SADP ..........................................................................................11

3.3 Modifying the IP Address ........................................................................................13

4 Accessing via Web Browser ........................................................................ 14

5 Hik-Connect................................................................................................ 15

5.1 Enable Hik-Connect for Use with Cameras .............................................................15

5.2 Enable Hik-Connect Service via SADP Software ......................................................15

5.2.1 Enable Hik-Connect via a Web Browser ...........................................................16

5.3 Add Camera to Hik-Connect ................................................................................... 17

5.4 Initialize the Memory Card .....................................................................................18

QSG EPI-5225I-AE 030518NA 6