Hikvision ECT-B12F6, ECT-B12F3, ECT-B12F2 Quick Start Guide

ECT-B12Fx
TurboHD Bullet Camera
ECT-B12Fx Quick Start Guide
Manual Illustrations and Features
Graphics (screen shots, product pictures, etc.) in this document are for illustrative purposes only. Your actual product may differ in appearance. Your product might not support all features discussed in this document.
Hikvision USA Inc., 18639 Railroad St., City of Industry, CA 91748, USA • Hikvision Canada, 4848 rue Levy, Saint Laurent, Quebec, Canada, H4R 2P1
Telephone: +1-909-895-0400 • Toll Free in USA: +1-866-200-6690 • E-Mail: sales.usa@hikvision.com • www.hikvision.com
COPYRIGHT ©2017-2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual.
About this Manual
This manual may contain technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and, if applicable, the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2014/35/EU, the EMC Directive 2014/30/EU.
2012/19/EU (WEEE Directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (Battery Directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation
QSG ECT-B12Fx 031518NA 2
ECT-B12Fx Quick Start Guide
for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”.
Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings Follow these safeguards to
prevent serious injury or death.
Warnings
In the use of the device, you must be in strict compliance with the electrical safety regulations of the nation and region.
Input voltage should meet both the SELV (S
with 12 VDC according to the IEC60950-1 standard. Refer to technical specifications for detailed information.
Do not connect multiple devices to one power adapter to avoid over-heating or a fire hazard caused by overload.
Make sure that the plug is firmly connected to the power socket.
Make sure that the device is firmly fixed if wall mounting or ceiling mounting is adopted.
If smoke, odor or noise rise from the device, turn off the power at once and unplug the power
cord, and then contact the service center.
Never attempt to disassemble the camera by unprofessional personal.
afety Extra Low Voltage) and the Limited Power Source
Cautions Follow these precautions to prevent potential injury or material damage.
Cautions
Do not drop the camera or subject it to physical shock.
Do not place the camera in extremely hot, cold (the operating temperature shall be -40°C to
60°C), dusty or damp locations, and do not expose it to high electromagnetic radiation.
Do not touch senor modules with fingers.
If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently.
QSG ECT-B12Fx 031518NA 3
ECT-B12Fx Quick Start Guide
Do not aim the camera at the sun or extra bright places.
The sensor may be burned out by a laser beam, so when any laser equipment is in using, make
sure that the surface of sensor will not be exposed to the laser beam.
Do not expose the device to high electromagnetic radiation or extremely hot, cold, dusty or damp environment.
To avoid heat accumulation, good ventilation is required for the operating environment.
Keep the camera away from liquid while in use for non-water-proof device.
While in delivery, the camera shall be packed in its original packing, or packing of the same
texture.
Mark Description
Mark Description
DC Voltage
QSG ECT-B12Fx 031518NA 4
ECT-B12Fx Quick Start Guide
Contents
1 Introduction .......................................................................... 6
1.1 Product Features ............................................................... 6
1.2 Overview ........................................................................... 6
1.2.1 Camera Overview..................................................... 6
2 Installation ............................................................................ 7
2.1 Installation of Camera ....................................................... 7
3 Menu Description ................................................................ 10
3.1 FORMAT .......................................................................... 11
3.2 EXPOSURE ....................................................................... 12
3.3 DAY/NIGHT ...................................................................... 12
3.4 VIDEO SETTINGS ............................................................. 15
3.5 FACTORY DEFAULT ........................................................... 16
3.6 EXIT ................................................................................. 17
3.7 SAVE & EXIT ..................................................................... 17
QSG ECT-B12Fx 031518NA 5
ECT-B12Fx Quick Start Guide
1 Introduction
1.1 Product Features
The main features are as follows:
High performance CMOS sensor
IR cut filter with auto switch
OSD menu with configurable parameters
Internal synchronization
SMART IR mode
3-axis adjustment
1.2 Overview
1.2.1 Camera Overview
Figure 1-1 Overview of Camera
QSG ECT-B12Fx 031518NA 6
ECT-B12Fx Quick Start Guide
2 Installation
Before You Start:
Make sure that the device in the package is in good condition
and all the assembly parts are included.
Make sure that all the related equipment is power-off during
the installation.
Check the specification of the products for the installation
environment.
Check whether the power supply is matched with your power
output to avoid the damage.
Make sure the wall is strong enough to withstand three times
the weight of the camera and the bracket.
If the wall is cement, insert expansion bolts before installing the
camera. If the wall is wooden, use self-tapping screws to secure the camera.
If the product does not function properly, contact your dealer
or the nearest service center. Do NOT disassemble the camera for repair or maintenance by yourself.
2.1 Installation of Camera
Before You Start:
Both wall mounting and ceiling mounting are suitable for the camera. Ceiling mounting will be taken as an example in this section. You can take the ceiling mounting steps as a reference when using wall mounting.
QSG ECT-B12Fx 031518NA 7
ECT-B12Fx Quick Start Guide
Steps:
1. Paste the drill template (supplied) where you want to install the
camera.
2. Drill the screw holes and the cable hole (optional) in the ceiling
according to the drill template.
Figure 2-1 Drill Template
Note:
Drill the cable hole if using the ceiling outlet to route the cable.
3. Attach the bracket to the ceiling, and secure the camera with
supplied screws.
QSG ECT-B12Fx 031518NA 8
ECT-B12Fx Quick Start Guide
Figure 2-2 Fix the Camera to the Ceiling
Note:
The supplied screw package contains self-tapping screws and expansion bolts.
For a cement ceiling, expansion bolts are required to fix the camera. For a wooden ceiling, self-tapping screws are required.
4. Route the cables through the cable hole or the side opening.
5. Connect the corresponding power cord and video cable.
6. Power on the camera to check if the image on the monitor is
gotten at an optimum angle. If not, adjust the camera according to the figure below to get an optimum angle.
Figure 2-3 3-axis Adjustment
QSG ECT-B12Fx 031518NA 9
ECT-B12Fx Quick Start Guide
1). Loosen the no. 3 screw to adjust the pan position [0° to 360°]. Tighten the screw after completing the adjustment.
2). Loosen the no. 2 screw to adjust the tilt position [0° to 180°]. Tighten the screw after completing the adjustment.
3). Loosen the no. 1 screw and rotate the camera [0° to 360°]. Tighten the screw after completing the adjustment.
3 Menu Description
Purpose:
Call the menu by clicking the button on the PTZ Control interface, or click Iris+.
Steps:
1. Connect the camera with the TVI DVR, and the monitor, shown as figure 3-1.
Figure 3-1 Connection
2. Power on the analog camera, TVI DVR, and the monitor to view the image on the monitor.
3. Click PTZ Control to enter the PTZ Control interface.
4. Call the camera menu by clicking the button, or click Iris+.
QSG ECT-B12Fx 031518NA 10
ECT-B12Fx Quick Start Guide
Figure 3-2 Main Menu Overview
5. Click the direction arrow to control the camera.
1) Click up/down direction button to select the item.
2) Click Iris + to confirm the selection.
3) Click left/right direction button to adjust the value of the
selected item.
3.1 FORMAT
You can set the format as 2 MP @ 30 fps.
QSG ECT-B12Fx 031518NA 11
ECT-B12Fx Quick Start Guide
3.2 EXPOSURE
Exposure describes the brightness-related parameters, which you can set the EXPOSURE MODE as GLOBAL, BLC, or DWDR.
GLOBAL
GLOBAL refers to the normal exposure mode, which sets
exposure according to the whole image brightness.
BLC (Backlight Compensation)
BLC (Backlight Compensation) compensates light for the front
object to make it clear, but this may cause the over-exposure of the background, where the light is strong.
DWDR (Digital Wide Dynamic Range)
DWDR helps the camera provide clear images even under
backlight circumstances. When both very bright and very dark areas simultaneously exist in the image, DWDR balances the brightness level of the whole image to provide clear images with details.
3.3 DAY/NIGHT
COLOR, BW (Black White), and AUTO are selectable for
DAY/NIGHT switch.
COLOR
The image is in color in day mode all the time.
B & W (Black and White)
The image is black and white all the time, and the IR LIGHT turns on in the poor light conditions.
QSG ECT-B12Fx 031518NA 12
ECT-B12Fx Quick Start Guide
You can turn on/off the IR LIGHT and set the value of SMART IR in this menu
DAY/NIGHT
MODE IR LIGHT SMART IR BACK EXIT SAVE & EXIT
B & W ON 2
Figure 3-3 B & W
IR LIGHT
You can turn on/off the IR LIGHT to meet the requirements of different circumstances.
SMART IR
The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure. The SMART IR value can be adjusted from 0 to 3. The higher the value is, the more obvious effects are.
AUTO
Automatically switch Color or BW (Black and White) according to actual scene brightness.
You can turn on/off the IR LIGHT and set the value of SMART IR in this menu.
QSG ECT-B12Fx 031518NA 13
ECT-B12Fx Quick Start Guide
Figure 3-4 AUTO
IR LIGHT
You can turn on/off the IR LIGHT to meet the requirements of different circumstances.
SMART IR
The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure. The SMART IR value can be adjusted from 0 to 3. The higher the value is, the more obvious effects are.
D N Threshold (Day to Night Threshold)
Day to Night Threshold is used to control the sensitivity of
switching the day mode to the night mode. You can set the value from 1 to 9. The larger the value is, the more sensitive the camera is.
N D Threshold (Night to Day Threshold)
Night to Day Threshold is used to control the sensitivity of
switching the night mode to the day mode. You can set the value from 1 to 9. The larger the value is, the more sensitive the camera is.
QSG ECT-B12Fx 031518NA 14
ECT-B12Fx Quick Start Guide
3.4 VIDEO SETTINGS
Move the cursor to VIDEO SETTINGS and click Iris+ to enter the submenu. BRIGHTNESS, CONTRAST, SHARPNESS, SATURATION, DNR, AGC, and MIRROR are adjustable.
Figure 3-5 VIDEO SETTINGS
BRIGHTNESS
Brightness refers to the brightness of the image.
You can set the brightness value from 1 to 9 to darken or brighten the image. The higher the value, the brighter the image.
CONTRAST
This feature enhances the difference in color and light between parts of an image. You can set the CONTRAST value from 1 to 9.
SHARPNESS
Sharpness determines the amount of detail an imaging system can reproduce. You can set the SHARPNESS value from 1 to 9.
QSG ECT-B12Fx 031518NA 15
ECT-B12Fx Quick Start Guide
SATURATION
Adjust this feature to change the saturation of the color. The value ranges from 1 to 9.
DNR (Digital Noise Reduction)
The DNR function can decrease the noise effect, especially when capturing moving images in poor light conditions and delivering more accurate and sharp image. You can set the DNR as HIGH, MEDIUM, or LOW.
AGC
It optimizes the clarity of the image in poor light conditions. The AGC level can be set as High, Medium, or Low. Select OFF to disable the AGC function.
Note:
The noise will be amplified when the AGC is on.
MIRROR
OFF, H, V, and HV are selectable for mirror.
OFF: The mirror function is disabled.
H: The image flips 180° horizontally.
V: The image flips 180° vertically.
HV: The image flips 180° both horizontally and vertically.
3.5 FACTORY DEFAULT
Move the cursor to FACTORY DEFAULT and click Iris+ to reset all the settings to the factory default.
QSG ECT-B12Fx 031518NA 16
ECT-B12Fx Quick Start Guide
3.6 EXIT
Move the cursor to EXIT and click Iris+ to exit the menu without saving.
3.7 SAVE & EXIT
Move the cursor to SAVE & EXIT and click Iris+ to save the settings, and exit the menu.
QSG ECT-B12Fx 031518NA 17
Loading...