How it Works
Hikvision
Loading...
ECI-B14F2
User Manual
21 pgs1.52 Mb0
Table of contents
Loading...

Hikvision ECI-B14F4, ECI-B14F2, ECI-B14F6 User Manual

ECI-B14F2 • ECI-B14F4 • ECI-B14F6
Network Bullet Camera
Quick Start Guide
Manual Illustrations and Features
Graphics (screen shots, product pictures, etc.) in this document are for illustrative purposes only. Your actual product may differ in appearance. Your product might not support all features discussed in this document.
Hikvision USA Inc., 18639 Railroad St., City of Industry, CA 91748, USA • Hikvision Canada, 4848 rue Levy, Saint Laurent, Quebec, Canada, H4R 2P1
Telephone: +1-909-895-0400 • Toll Free in USA: +1-866-200-6690 • E-Mail:
sales.usa@hikvision.com • www.hikvision.com
COPYRIGHT ©2017-2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual.
About this Manual
This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
QSG VE ECI-B14Fx 060118NA 2
which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and, if applicable, the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the Low Voltage
Directive 2014/35/EU, the EMC Directive 2014/30/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your
local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific
battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
QSG VE ECI-B14Fx 060118NA 3
Warnings
Cautions Follow
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”.
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Follow these safeguards to prevent serious injury or death.
these precautions to prevent potential injury or material damage.
Warnings
In the use of the device, you must be in strict compliance with the
electrical safety regulations of the nation and region.
Input voltage should meet both the SELV (Safety Extra Low Voltage) and
the Limited Power Source with 12 VDC according to the IEC60950-1 standard. Refer to technical specifications for detailed information.
The output current of the power adapter must be no more than 6A.
Do not connect multiple devices to one power adapter to avoid
over-heating or a fire hazard caused by overload.
Make sure that the plug is firmly connected to the power socket.
Make sure that the device is firmly fixed if wall mounting or ceiling
mounting is adopted.
If smoke, odor or noise rise from the device, turn off the power at once
and unplug the power cord, and then contact the service center.
Never attempt to disassemble the camera by unprofessional personal.
QSG VE ECI-B14Fx 060118NA 4
Mark
Description
DC Voltage
Cautions
Do not drop the camera or subject it to physical shock.
Do not place the camera in extremely hot, cold (the operating
temperature shall be -40° to 60° C), dusty or damp locations, and do not expose it to high electromagnetic radiation.
Do not touch senor modules with fingers.
If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it
gentl y.
Do not aim the camera at the sun or extra bright places.
The sensor may be burned out by a laser beam, so when any laser
equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam.
Do not expose the device to high electromagnetic radiation or extremely
hot, cold, dusty or damp environment.
To avoid heat accumulation, good ventilation is required for the operating
environment.
Keep the camera away from liquid while in use for non-water-proof
device.
While in delivery, the camera shall be packed in its original packing, or
packing of the same texture.
Mark Description
QSG VE ECI-B14Fx 060118NA 5
Contents
1 Appearance Description ......................................................................... 7
2 Installation ............................................................................................. 7
2.1 Ceiling/Wall Mounting .................................................................... 8
2.2 Ceiling/Wall Mounting with Junction Box .................................... 10
2.3 Waterproof Jacket Installation...................................................... 12
3 Set the Network Camera over the LAN .................................................. 13
3.1 Wiring ........................................................................................... 13
3.2 Activate the Camera ..................................................................... 14
3.2.1 Activation via Web Browser ............................................... 14
3.2.2 Activation via SADP Software ............................................ 15
3.3 Modify the IP Address .................................................................. 16
3.4 Access via Web Browser ............................................................... 17
3.5 Operate via Hik-Connect App ....................................................... 18
3.5.3 Enable Hik-Connect for Use with Cameras ........................ 18
3.5.4 Enable Hik-Connect Service via SADP Software ................ 18
3.5.5 Enable Hik-Connect via a Web Browser ............................ 19
3.5.6 Add Camera to Hik-Connect .............................................. 20
QSG VE ECI-B14Fx 060118NA 6
D
C
1
2
V
I
N
5
6
1
2
4
3
No.
Description
1
Lens
2
Front Cover
3
Back Cover
4
Fix Ring
5
Power Cord
6
Network Cable

1 Appearance Description

This network bullet camera appearance is shown as the figures below.
Network Bullet Camera Overview
NOTE:
For power over Ethernet (PoE), the power is passed along with data on Ethernet cabling. A switch that supports the PoE function is required.

2 Installation

Before You Start:
Make sure the device in the package is in good condition and all the
assembly parts are included.
The standard power supply is 12 VDC, make sure your power supply
matches your camera.
Make sure all related equipment is powered off during the installation.
Check the product specification for the installation environment.
Make sure that the wall is strong enough to withstand four times the
weight of the camera and the bracket.
Make sure that there are no reflective surfaces too close to the camera
lens. The IR light from the camera may reflect back into the lens causing reflection.
QSG VE ECI-B14Fx 060118NA 7
Loading...
+ 14 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use