HIKVISION DS-K2801, DS-K2802, DS-K2804 User Manual

DS-K2800 Series Access Controller

User Manual

Access Controller·User Manual

User Manual

Product Name

Serials

Access

Controller

DS-K2801 Serials Access Controller

DS-K2802 Serials Access Controller

DS-K2804 Serials Access Controller

It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product.

About this Manual

This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision

Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be

reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.

Trademarks

and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

Support

Should you have any questions, please do not hesitate to contact your local dealer.

Access Controller·User Manual

Regulatory Information FCC Information

Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected. —Consult the dealer or an experienced radio/TV technician for help.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the R&TTE Directive 1999/5/EC, the EMC Directive 2014/30/EU, the LVD

Directive 2014/35/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated

collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Access Controller·User Manual

iii

Preventive and Cautionary Tips

Before connecting and operating your device, please be advised of the following tips:

• Ensure unit is installed in a well-ventilated, dust-free environment.

• Keep all liquids away from the device.

• Ensure environmental conditions meet factory specifications.

• Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of

dropping it may cause damage to the sensitive electronics within the unit.

• Use the device in conjunction with an UPS if possible.

• Power down the unit before connecting and disconnecting accessories and peripherals.

• A factory recommended HDD should be used for this device.

Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the manufacturer.

Access Controller·User Manual

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions:

Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage.

Warnings

 All the electronic operation should be strictly compliance with the electrical safety regulations,

fire prevention regulations and other related regulations in your local region.

 Please use the power adapter, which is provided by normal company. The power consumption

cannot be less than the required value.

 Do not connect several devices to one power adapter as adapter overload may cause over-heat

or fire hazard.

 Please make sure that the power has been disconnected before you wire, install or dismantle

the device.

 When the product is installed on wall or ceiling, the device shall be firmly fixed.  If smoke, odors or noise rise from the device, turn off the power at once and unplug the power

cable, and then please contact the service center.

 If the product does not work properly, please contact your dealer or the nearest service center.

Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)

Cautions

 Do not drop the device or subject it to physical shock, and do not expose it to high

electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).

 Do not place the device in extremely hot (refer to the specification of the device for the detailed

operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The appropriate operation temperature is 0℃ to +45℃, and the storage temperature should be -10℃ to +55℃.

 The device cover for indoor use shall be kept from rain and moisture.  Exposing the equipment to direct sun light, low ventilation or heat source such as heater or

radiator is forbidden (ignorance can cause fire danger).

 Do not aim the device at the sun or extra bright places. A blooming or smear may occur

otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.

 Please use the provided glove when open up the device cover, avoid direct contact with the

device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.

 Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do

not use alkaline detergents.

Warnings Follow these safeguards to prevent serious injury or death.

Cautions Follow these precautions to prevent potential injury or material damage.

Access Controller·User Manual

 Please keep all wrappers after unpack them for future use. In case of any failure occurred, you

need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs.

 Improper use or replacement of the battery may result in hazard of explosion. Replace with the

same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.

Access Controller·User Manual

Table of Contents

Chapter 1 Product Description ................................................................................................. 1

1.1 Overview .............................................................................................................................. 1

1.2 Main Features ...................................................................................................................... 1

Chapter 2 Component Description ........................................................................................... 2

Chapter 3 Terminal Connection ................................................................................................ 3

3.1 DS-K2801 Terminal Description ............................................................................................ 3

3.2 DS-K2802Terminal Description............................................................................................. 5

3.3 DS-K2804 Terminal Description ............................................................................................ 7

Chapter 4 External Device Wiring .......................................................................................... 10

4.1 Card Reader Wiring ............................................................................................................ 10

4.1.1 Wiegand Card Reader Wiring ........................................................................................ 10

4.1.2 DS-K1800 Series Card Reader Wiring ............................................................................. 10

4.2 DS-K2801 External Terminals ............................................................................................. 10

4.2.1 Installation of Cathode Lock ........................................................................................... 11

4.2.2 Installation of Anode Lock .............................................................................................. 11

4.3 Connecting the External Alarm Device .............................................................................. 12

4.4 Door Button Wiring Diagram ............................................................................................. 12

4.5 The Connection of Magnetics Detection ........................................................................... 13

4.6 Connecting Power Supply .................................................................................................. 13

Chapter 5 Settings ................................................................................................................. 14

5.1 Initializing the Hardware .................................................................................................... 14

5.2 Relay Input NO/NC ............................................................................................................. 14

5.2.1 Lock Relay Output .......................................................................................................... 14

5.2.2 Alarm Relay Output Status ............................................................................................. 15

Chapter 6 Activating the Access Control Terminal ................................................................... 17

6.1 Activating via SADP Software ............................................................................................. 17

6.2 Activating via Client Software ............................................................................................ 18

Chapter 7 Client Operation .................................................................................................... 21

7.1 Function Module ................................................................................................................ 21

7.2 User Registration and Login ............................................................................................... 21

7.3 System Configuration ......................................................................................................... 22

7.4 Access Control Management ............................................................................................. 23

7.4.1 Adding Access Control Device ........................................................................................ 24

7.4.2 V iewing Device Status .................................................................................................... 33

Access Controller·User Manual

vii

7.4.3 Editing Basic Information ............................................................................................... 33

7.4.4 Remote Configuration .................................................................................................... 33

7.5 Person and Card Management .......................................................................................... 39

7.5.1 Organization Management ............................................................................................ 39

7.5.2 Person Management ...................................................................................................... 40

7.6 Schedule and Template ...................................................................................................... 48

7.6.1 Week Schedule ............................................................................................................... 49

7.6.2 Holiday Group ................................................................................................................ 50

7.6.3 Template ......................................................................................................................... 51

7.7 Permission Configuration ................................................................................................... 53

7.7.1 Adding Permission .......................................................................................................... 54

7.7.2 Applying Permission ....................................................................................................... 55

7.8 Advanced Functions ........................................................................................................... 55

7.8.1 Access Control Parameters ............................................................................................. 56

7.8.2 Card Reader Authentication ........................................................................................... 58

7.8.3 Open Door with First Card ............................................................................................. 59

7.8.4 Anti-Passing Back ........................................................................................................... 60

7.8.5 Authentication Password ............................................................................................... 62

7.8.6 Custom Wiegand ............................................................................................................ 62

7.9 Searching Access Control Event ......................................................................................... 64

7.10 Access Control Event Configuration ................................................................................... 65

7.10.1 Access Control Event Linkage ..................................................................................... 65

7.10.2 Access Control Alarm Input Linkage ........................................................................... 67

7.10.3 Event Card Linkage ..................................................................................................... 67

7.10.4 Cross-Device Linkage .................................................................................................. 69

7.11 Door Status Management .................................................................................................. 70

7.11.1 Access Control Group Management .......................................................................... 70

7.11.2 Anti-control the Access Control Point (Door) ............................................................. 72

7.11.3 Status Duration Configuration ................................................................................... 73

7.11.4 Real-time Card Swiping Record .................................................................................. 75

7.11.5 Real-time Access Control Alarm ................................................................................. 75

7.12 Arming Control ................................................................................................................... 76

Appendix A Sound Prompt and Indicator .................................................................................. 78

Appendix B Custom Wiegand Rule............................................................................................ 79

Access Controller·User Manual

Chapter 1 Product Description

1.1 Overview

DS-K2800 is a powerful and stable access controller, using the logical architecture design. DS-K2800 is designed with TCP/IP network interface and its signal processed with special encryption and can be run offline. Anti-tampering function is also supported.

1.2 Main Features

 The access controller is equipped with 32-bit high-speed processor  Supports TCP/IP network communication, with self-adaptive network interface. The

communication data is specially encrypted to relieve the concern of privacy leak

 Supports recognition and storage of card number with maximum length of 20  The access controller can store 10 thousand legal cards and 50 thousand card swiping records  Supports first card open-door and first card authorization function, super card and super

password function, online upgrade function and remote control of the doors

 Supports Wiegand interface for accessing card reader. Wiegand interface supports W26/W34

and is seamlessly compatible with third-party card reader with Wiegand interface

 Supports various card types as normal/ disabled/ blacklist/ patrol/ guest/ duress/ super card,

etc.

 Supports time synchronization via NTP, manual or automatic method  Supports record storage function when it is offline and insufficient storage space storage alarm

function

 The access controller has watchdog design  Data can be permanently saved after the access controller is powered off.  Supports I/O linkage, and event linkage  Supports alarm of offline event exceeding 90%  Multiple event upload methods: channel, center group, and listening  500 groups of authentication code  Anti-pass-back function.

Access Controller·User Manual

Chapter 2 Component Description

Take DS-K2804 as an example, the component schematic diagram is shown below.

DS-K2800 component descriptions are as follows:

No.

Component Description

DS-K2801

DS-K2802

DS-K2804

Door Lock 1 Indicator

Door Lock 1/2 Indicator

Door Lock 1/2/3/4 Indicator

Power Indicator

Network Indicator

Jumper Cap for Restoring Factory Settings

Working Indicator

Alarm Output Indicator

Alarm Output (NO/NC) Jumper Cap

Access Controller·User Manual

Chapter 3 Terminal Connection

3.1 DS-K2801 Terminal Description

DS-K2801 Terminal descriptions are as follows:

No.

DS-K2801

Power

GND

DC12V Grounding

+12V

DC12V Input

Door

Door Lock Relay Output

COM

BUTTON

Door Button Input

GND

Grounding

Access Controller·User Manual

No.

DS-K2801

SENSOR

Door Magnetic detector

Alarm Output

COM

Alarm Relay Output (Dry Contact)

NO/NC

Alarm Input

GND

Grounding

Event Input

Wiegand Card

Reader 1

Indicator of Card Reader Control Output (Valid Card Output)

ERR

Indicator of Card Reader Control Output (Invalid Card Output)

Card Reader Buzzer Control Output

Wiegand Head Read Data Input Data1

Wiegand Head Read Data Input Data0

B10

PWR

Card Reader Power Output

B11

GND

B12

Wiegand Card

Reader 2

Indicator of Card Reader Control Output (Valid Card Output)

B13

ERR

Indicator of Card Reader Control Output (Invalid Card Output)

B14

Card Reader Buzzer Control Output

B15

Wiegand Head Read Data Input Data1

B16

Wiegand Head Read Data Input Data0

B17

PWR

Card Reader Power Output

B18

GND

Access Controller·User Manual

3.2 DS-K2802Terminal Description

DS-K2802 Terminal descriptions are as follows:

No.

DS-K2802

Alarm Input

IN2

Event Input 2

GND

Grounding

IN1

Event Input 1

Door 2

Door Lock Relay Output (Dry Contact)

COM

BUTTON

Door Button Input

GND

Grounding

SENSOR

Door Magnetic detector

Door 1

Door Lock Relay Output (Dry Contact)

COM

B10

BUTTON

Door Button Input

B11

GND

Grounding

B12

SENSOR

Door Magnetic detector

Power

GND

DC12V Grounding

+12V

DC12V Input

Alarm Output 2

COM2

Alarm Relay Output 2 (Dry Contact)

NO/NC2

Access Controller·User Manual

No.

DS-K2802

Alarm Output 1

COM1

Alarm Relay Output 1 (Dry Contact)

NO/NC1

Wiegand Card

Reader 1

Indicator of Card Reader Control Output (Valid Card Output)

ERR

Indicator of Card Reader Control Output (Invalid Card Output)

Card Reader Buzzer Control Output

Wiegand Head Read Data Input Data1

Wiegand Head Read Data Input Data0

PWR

Card Reader Power Output

GND

Wiegand Card

Reader 2

Indicator of Card Reader Control Output (Valid Card Output)

ERR

Indicator of Card Reader Control Output (Invalid Card Output)

C10

Card Reader Buzzer Control Output

C11

Wiegand Head Read Data Input Data1

C12

Wiegand Head Read Data Input Data0

C13

PWR

Card Reader Power Output

C14

GND

C15

Wiegand Card

Reader 3

Indicator of Card Reader Control Output (Valid Card Output)

C16

ERR

Indicator of Card Reader Control Output (Invalid Card Output)

C17

Card Reader Buzzer Control Output

C18

Wiegand Head Read Data Input Data1

C19

Wiegand Head Read Data Input Data0

C20

PWR

Card Reader Power Output

C21

GND

C22

Wiegand Card

Reader 4

Indicator of Card Reader Control Output (Valid Card Output)

C23

ERR

Indicator of Card Reader Control Output (Invalid Card Output)

C24

Card Reader Buzzer Control Output

C25

Wiegand Head Read Data Input Data1

C26

Wiegand Head Read Data Input Data0

C27

PWR

Card Reader Power Output

C28

GND

Access Controller·User Manual

3.3 DS-K2804 Terminal Description

DS-K2804 Terminal descriptions are as follows:

No.

DS-K2804

Alarm Input

IN4

Event Input 4

GND

Grounding

IN3

Event Input 3

IN2

Event Input 2

GND

Grounding

IN1

Event Input 1

Door 4

Door Lock Relay Output (Dry Contact)

COM

A10

BUTTON

Door Button Input

A11

GND

Grounding

A12

SENSOR

Door Magnetic detector

A13

Door 3

Door Lock Relay Output (Dry Contact)

A14

COM

A15

A16

BUTTON

Door Button Input

A17

GND

Grounding

A18

SENSOR

Door Magnetic detector

Access Controller·User Manual

No.

DS-K2804

A19

Door 2

Door Lock Relay Output (Dry Contact)

A20

COM

A21

A22

BUTTON

Door Button Input

A23

GND

Grounding

A24

SENSOR

Door Magnetic detector

A25

Door 1

Door Lock Relay Output (Dry Contact)

A26

COM

A27

A28

BUTTON

Door Button Input

A29

GND

Grounding

A30

SENSOR

Door Magnetic detector

Wiegand Card

Reader 1

Indicator of Card Reader Control Output (Valid Card Output)

ERR

Indicator of Card Reader Control Output (Invalid Card Output)

Card Reader Buzzer Control Output

Wiegand Head Read Data Input Data1

Wiegand Head Read Data Input Data0

PWR

Card Reader Power Output

GND

Wiegand Card

Reader 2

Indicator of Card Reader Control Output (Valid Card Output)

ERR

Indicator of Card Reader Control Output (Invalid Card Output)

B10

Card Reader Buzzer Control Output

B11

Wiegand Head Read Data Input Data1

B12

Wiegand Head Read Data Input Data0

B13

PWR

Card Reader Power Output

B14

GND

B15

Wiegand Card

Reader 3

Indicator of Card Reader Control Output (Valid Card Output)

B16

ERR

Indicator of Card Reader Control Output (Invalid Card Output)

B17

Card Reader Buzzer Control Output

B18

Wiegand Head Read Data Input Data1

B19

Wiegand Head Read Data Input Data0

B20

PWR

Card Reader Power Output

B21

GND

B22

Wiegand Card

Reader 4

Indicator of Card Reader Control Output (Valid Card Output)

B23

ERR

Indicator of Card Reader Control Output (Invalid Card Output)

Access Controller·User Manual

No.

DS-K2804

B24

Card Reader Buzzer Control Output

B25

Wiegand Head Read Data Input Data1

B26

Wiegand Head Read Data Input Data0

B27

PWR

Card Reader Power Output

B28

GND

Power

GND

DC12V Grounding

+12V

DC12V Input

Alarm Output 4

COM4

Alarm Relay Output 4 (Dry Contact)

NO/NC4

Alarm Output 3

COM3

Alarm Relay Output 3 (Dry Contact)

NO/NC3

Alarm Output 2

COM2

Alarm Relay Output 2 (Dry Contact)

NO/NC2

Alarm Output 1

COM1

Alarm Relay Output 1 (Dry Contact)

NO/NC1

Notes:

 The Alarm input hardware interface is normally open by default. So only the normally open

signal is allowed. It can be linked to the buzzer of the card reader and access controller, and the alarm relay output and open door relat output.

 For single-door access controller, the Wiegand card reader 1 and 2 respectively correspond to

the entering and exiting card readers of door 1. For two-door access controller, the Wiegand card reader 1 and 2 respectively correspond to the entering and exiting card readers of door 1 , and the Wiegand card reader 3 and 4 respectively correspond to the entering and exiting card readers of door 2. For four-door access controller, the Wiegand card reader 1, 2, 3 and 4 respectively correspond to the entering card readers of door 1, 2, 3, and 4.

Access Controller·User Manual

Chapter 4 External Device Wiring

4.1 Card Reader Wiring

4.1.1 Wiegand Card Reader Wiring

Black

Red

Green

White

Purple

Orange

Brown

Controller

Card Reader

Note: You must connect the OK/ERR/BZ, if using access controller to control the LED and buzzer of

the Wiegand card reader.

4.1.2 DS-K1800 Series Card Reader Wiring

GND

VCC

WG-D0

WG-D1

WG_BEEP

WG_ERR

WG_OK

Controller

Card Reader

LED

4.2 DS-K2801 External Terminals

Access Controller·User Manual

4.2.1 Installation of Cathode Lock

4.2.2 Installation of Anode Lock

Access Controller·User Manual

4.3 Connecting the External Alarm Device

4.4 Door Button Wiring Diagram

Access Controller·User Manual

4.5 The Connection of Magnetics Detection

4.6 Connecting Power Supply

Access Controller·User Manual

Chapter 5 Settings

5.1 Initializing the Hardware

Option 1:

Steps:

1. Remove the jumper cap from the Normal terminal.

2. Disconnect the power and restart the access controller. The controller buzzer buzzes a long

beep.

3. When the beep stopped, plug the jumper cap back to Normal.

4. Disconnect the power and restart the access controller.

Option 2:

Steps:

1. Jump the jumper cap from Normal to Initial.

2. Disconnect the power and restart the access controller. The controller buzzer buzzes a long

beep.

3. When the beep stopped, jump the jumper cap back to Normal.

4. Disconnect the power and restart the access controller.

DS-K2801 Initialization Dial-up

DS-K2802/DS-K2804 Initialization Dial-up

Note: The initializing of the hardware will restore all the parameters to the default setting and all

the device events are wiping out.

5.2 Relay Input NO/NC

5.2.1 Lock Relay Output

Lock Relay Normally Open Status:

Access Controller·User Manual

Lock Relay Normally Closed Status:

5.2.2 Alarm Relay Output Status

Alarm Relay Output Normally Open:

Alarm Relay Output Normally Closed:

Work Flow of Software

For detailed information, please see the user manual of the client software. Refer to the following work flow:

Access Controller·User Manual

Chapter 6 Activating the Access Control

Terminal

Purpose:

You are required to activate the terminal first before using it. Activation via SADP, and Activation via client software are supported. The default values of the control terminal are as follows.

 The default IP address: 192.0.0.64.  The default port No.: 8000.  The default user name: admin.

6.1 Activating via SADP Software

SADP software is used for detecting the online device, activating the device, and resetting the password. Get the SADP software from the supplied disk, and install the SADP according to the prompts. Follow the steps to activate the control panel. Steps:

1. Run the SADP software to search the online devices.

2. Check the device status from the device list, and select an inactive device.

3. Create a password and input the password in the password field, and confirm the password.

STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

4. Click Activate to activate the device.

5. Check the activated device. You can change the device IP address to the same network

Access Controller·User Manual

segment with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.

6. Input the password and click the Modify button to activate your IP address modification.

6.2 Activating via Client Software

The client software is versatile video management software for multiple kinds of devices. Get the client software from the supplied disk, and install the software according to the prompts. Follow the steps to activate the control panel.

Steps:

1. Run the client software and the control panel of the software pops up, as shown in the figure

below.

Access Controller·User Manual

2. Click the Device Management to enter the Device Management interface.

3. Check the device status from the device list, and select an inactive device.

4. Click the Activate button to pop up the Activation interface.

5. In the pop-up window, create a password in the password field, and confirm the password.

+ 61 hidden pages

HIKVISION DS-K2801, DS-K2802, DS-K2804 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual