Hikvision DS-2XC6122FWD-IS-2.8mm, DS-2XC6122FWD-IS-4mm, DS-2XC6122FWD-IS-6mm, DS-2XC6142FWD-IS-4mm, DS-2XC6142FWD-IS-6mm Quick Start Guide

Download

UD04286B

0504051070109

Anti-Corrosion Network Dome Camera

Quick Start Guide

Network Dome Camera·Quick Start Guide

Quick Start Guide

Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).

This user manual (hereinafter referred to be “the Manual”) cannot

be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of

Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual.

About this Manual

This Manual is applicable to XC61 Series Network Camera.

The Manual includes instructions for using and managing the

product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without

notice, due to firmware updates or other reasons. Please find the latest version in the company website (http://overseas.hikvision.com/en/).

Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement

and other Hikvision’s trademarks and logos are the

properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.

Network Dome Camera·Quick Start Guide

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,

AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND

NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL

HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR

INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF

THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL

NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET

SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS

PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.

Network Dome Camera·Quick Start Guide

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help

FCC Conditions

Network Dome Camera·Quick Start Guide

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied

accessories too are marked with "CE" and comply

standards listed under the EMC Directive 2014/30/EU, the RoHS

Directive 2011/65/EU.

upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:

www.recyclethis.info

which may include lettering to indicate cadmium (Cd), lead (Pb), or

mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info

therefore with the applicable harmonized European

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper

recycling, return this product to your local supplier

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union.

See the product documentation for specific battery information. The battery is marked with this symbol,

Network Dome Camera·Quick Start Guide

Warnings Follow these

safeguards to prevent serious injury or death.

Cautions Follow these precautions to prevent potential injury or material

damage.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.

The precaution measure is divided into “Warnings” and “Cautions”

Warnings: Serious injury or death may occur if any of the warnings

are neglected.

Cautions: Injury or equipment damage may occur if any of the

cautions are neglected.

Warnings

● Proper configuration of all passwords and other security

settings is the responsibility of the installer and/or end-user.

Network Dome Camera·Quick Start Guide

● In the use of the product, you must be in strict compliance with

the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.

● Input voltage should meet both the SELV (Safety Extra Low

Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.

● Do not connect several devices to one power adapter as

adapter overload may cause over-heating or a fire hazard.

● Please make sure that the plug is firmly connected to the power

socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed.

● If smoke, odor or noise rise from the device, turn off the power

at once and unplug the power cable, and then please contact the service center.

Cautions

● Make sure the power supply voltage is correct before using the

camera.

● Do not drop the camera or subject it to physical shock.

● Do not touch sensor modules with fingers. If cleaning is

necessary, use clean cloth with a bit of ethanol and wipe it

gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt.

● Do not aim the camera at the sun or extra bright places.

Blooming or smearing may occur otherwise (which is not a

Network Dome Camera·Quick Start Guide

malfunction), and affect the endurance of sensor at the same time.

● The sensor may be burned out by a laser beam, so when any

laser equipment is in using, make sure that the surface of

sensor will not be exposed to the laser beam.

● Do not place the camera in extremely hot, cold (the operating

temperature shall be-30°C to +60°C , or -40°C to +60°C if the

camera model has an “H” in its suffix), dusty or damp locations,

and do not expose it to high electromagnetic radiation.

● To avoid heat accumulation, good ventilation is required for

operating environment.

● Keep the camera away from liquid while in use.

● While in delivery, the camera shall be packed in its original

packing, or packing of the same texture.

● Regular part replacement: a few parts (e.g. electrolytic

capacitor) of the equipment shall be replaced regularly according to their average enduring time. The average time varies because of differences between operating environment

and using history, so regular checking is recommended for all the users. Please contact with your dealer for more details.

● Improper use or replacement of the battery may result in

hazard of explosion. Replace with the same or equivalent type

only. Dispose of used batteries according to the instructions provided by the battery manufacturer.

● If the product does not work properly, please contact your

dealer or the nearest service center. Never attempt to

disassemble the camera yourself. (We shall not assume any

Network Dome Camera·Quick Start Guide

responsibility for problems caused by unauthorized repair or maintenance.)

0504051070109

Network Dome Camera·Quick Start Guide

Table of Contents

1 Appearance Description ............................................................... 10

2 Installation .................................................................................... 12

Install Memory Card ...................................................... 13

Ceiling Mounting ........................................................... 14

Wall Mounting .............................................................. 18

3 Setting the Network Camera over the LAN .................................. 21

Wiring ........................................................................... 21

Activating the Camera ................................................... 22

Activation via Web Browser ................................ 22

Activation via SADP Software ............................. 23

Modifying the IP Address .............................................. 25

4 Accessing via Web Browser .......................................................... 28

5 Operating via Hik-Connect App .................................................... 30

5.1 Enable Hik-Connect Service on Camera ......................... 30

Enable Hik-Connect Service via SADP Software .. 30

Enable Hik-Connect Service via Web Browser .... 31

5.2 Hik-Connect Setup ........................................................ 33

5.3 Adding Camera to Hik-Connect ..................................... 33

5.4 Initializing the Memory Card ......................................... 35

Network Dome Camera·Quick Start Guide

1 Appearance Description

The overview of the anti-corrosion dome camera is shown below:

Overview

Network Dome Camera·Quick Start Guide

No.

Description

No.

Description

Front cover

Photoresistor

Lens 4 IR lights

Dome drive

Reset button

Memory card slot

Power supply (DC 12V)

RJ45 network interface

Alarm input and output interface

Side outlet

Description

Note:

RESET operation with reset button: press and hold the reset button for at least 10 s when camera is powering on. Then release the button.

Network Dome Camera·Quick Start Guide

2 Installation

Before you start:

● Make sure the device in the package is in good condition and all

the assembly parts are included.

● The standard power supply is 12V DC, please make sure your

power supply matches with your camera.

● Make sure all the related equipment is power-off during the

installation.

● Check the specification of the products for the installation

environment.

● Make sure that the wall is strong enough to withstand four

times the weight of the camera and the bracket.

For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection:

● Dust or grease on the dome cover will cause IR reflection.

Please do not remove the dome cover film until the installation

is finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol.

● Make sure that there is no reflective surface too close to the

camera lens. The IR light from the camera may reflect back into

the lens causing reflection.

● The foam ring around the lens must be seated flush against the

inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring

and the dome cover are attached seamlessly.

Network Dome Camera·Quick Start Guide

Front Cover

Allen Wrench

Memory Card

Slot

Install Memory Card

Steps:

1. Unscrew the front cover with supplied Allen wrench to expose the

memory card slot.

Unscrew Front Cover

2. Insert the memory card into the memory card slot.

Network Dome Camera·Quick Start Guide

Memory

Card

Insert Memory Card

3. (Optional) If you need to unmount the memory card, push to get it

ejected.

Ceiling Mounting

Steps:

1. Paste the drill template to the desired mounting place.

Network Dome Camera·Quick Start Guide

FRONT

Drill Template

Hole A: Rout cables through the ceiling

Hole B: Side outlet

Hole 1: Fix the mounting base

Please use Φ 5.5mm drill to

install expansion screws

Code: 102010928

Drill Template

2. Drill three screw holes according to Hole 1 on the drill template

and plan cable routing.

Note:

If you choose to route cable through ceiling, drill a cable hole

according to Hole A.

3. Range the drill template, the supplied shock-absorbing pad, and

the camera base in the shown order. Secure them with three expansion screws.

Note:

Connect the cables before installing the camera base, if you

choose to route cables through ceiling.

Network Dome Camera·Quick Start Guide

Drill Template

Shock-Absorbing

Pad

Camera Base

Install Camera

4. Adjust surveillance angle. See Figure 2-5.

1). Stick the supplied plastic ring in the dome drive.

2). Connect the cables and power on the camera to view live

view image.

3). Hole and move the plastic ring to adjust the panning, tilting

and rotating position to desired place.

4). Remove the plastic ring after finishing adjustment.

Network Dome Camera·Quick Start Guide

Plastic Ring

Tilt: 0° to 75°

Rotate: 0° to 360°

Pan: -30° to +30°

Adjust Surveillance Angle

5. Install the front cover back to the camera.

Install Front Cover

Network Dome Camera·Quick Start Guide

Wall Mounting

Before You Start:

Wall mounting bracket is not included in package. You need to prepare one in advance if you adopt this mounting type. The shown

bracket below is only for demonstration.

Wall Mounting Bracket

Steps:

1. Paste the drill template of the wall mounting bracket to desired

mounting place.

Drill Template of Wall Mounting Bracket

Network Dome Camera·Quick Start Guide

Expansion Bolts

Wall

Wall Mounting

Bracket

Shock-Absorbing

Pad

Camera

Cable

2. Drill 4 screw holes according to Hole 1 on the template.

3. Insert supplied expansion bolts. Unscrew the nuts and gaskets.

Insert Expansion Bolts

4. Range the wall mounting bracket, the supplied shock-absorbing

pad, and the camera in the shown order. Route the cable and

secure them with three screws.

Secure Camera to Wall Mounting Bracket

Network Dome Camera·Quick Start Guide

Nuts Gaskets

5. Hang the bracket to the bolts. Fix the wall mounting bracket to

wall with gaskets and nuts.

Fix Wall Mounting Bracket to Wall

6. Unscrew the front cover to mount memory card, and adjust

surveillance angle. Refer to Section 2.1 Install Memory Card, and Step 4 in Section 2.2 Ceiling Mounting.

7. Install the front cover back to the camera to finish installation.

Network Dome Camera·Quick Start Guide

Network Cable

Network Camera

Computer

Network Cable

Network Camera Computer

3 Setting the Network Camera over the

LAN

Note:

You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any

network attacks and information leakage, please strengthen your

own protection.

If the product does not work properly, contact your dealer or the nearest service center for help.

Wiring

Connect the camera to network according to the following figures.

Connecting Directly

Connecting via a Switch or a Router

Network Dome Camera·Quick Start Guide

Activating the Camera

You are required to activate the camera first by setting a strong password for it before you can use the camera.

Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP

software and Activation via Web Browser as examples to introduce the camera activation.

Note:

Refer to the User Manual of Network Camera for Activation via Client Software.

Activation via Web Browser

Steps:

1. Power on the camera. Connect the camera to your computer or

the switch/router which your computer connects to.

2. Input the IP address into the address bar of the web browser, and

press Enter to enter the activation interface.

Notes:

 The default IP address of the camera is 192.168.1.64.  The computer and the camera should belong to the same

subnet.

 For the camera enables the DHCP by default, you need to use

the SADP software to search the IP address.

Network Dome Camera·Quick Start Guide

Activation Interface(Web)

3. Create a password and input the password into the password

field.

STRONG PASSWORD RECOMMENDED– W e highly

recommend you create a strong password of your own

choosing (using a minimum of 8 characters, including

upper case letters, lower case letters, numbers, and

special characters) in order to increase the security of

your product. And we recommend you reset your

password regularly, especially in the high security

system, resetting the password monthly or weekly can

better protect your product.

4. Confirm the password.

5. Click OK to save the password and enter the live view interface.

Activation via SADP Software

SADP software is used for detecting the online device, activating the camera, and resetting the password.

Network Dome Camera·Quick Start Guide

Select inactive device.

Input and confirm password.

Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts.

Follow the steps to activate the camera.

Steps:

1. Run the SADP software to search the online devices.

2. Check the device status from the device list, and select the

inactive device.

SADP Interface

Note:

The SADP software supports activating the camera in batch. Refer to the user manual of SADP software for details.

3. Create and input the new password in the password field, and

confirm the password.

Network Dome Camera·Quick Start Guide

STRONG PASSWORD RECOMMENDED– W e highly

recommend you create a strong password of your own

choosing (using a minimum of 8 characters, including

upper case letters, lower case letters, numbers, and

special characters) in order to increase the security of

your product. And we recommend you reset your

password regularly, especially in the high security

system, resetting the password monthly or weekly can

better protect your product.

Note:

You can enable the Hik-Connect service for the device during

activation. Refer to Chapter 5.1 for detailed information.

4. Click Activate to start activation.

You can check whether the activation is completed on the popup window. If activation failed, make sure that the password meets the requirement and try again.

Modifying the IP Address

Purpose:

To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC.

Use the SADP software or client software to search and change the

IP address of the device. We take modifying the IP Address via SADP software as an example to introduce the IP address modification.

For IP address modification via client software, refer to the user manual of client software.

Network Dome Camera·Quick Start Guide

Steps:

1. Run the SADP software.

2. Select an active device.

3. Change the device IP address to the same subnet with your

computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.

Modify the IP Address

Network Dome Camera·Quick Start Guide

Note:

You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information.

4. Input the admin password and click Modify to activate your IP

address modification.

The batch IP address modification is supported by the SADP. Refer to

the user manual of SADP for details.

Network Dome Camera·Quick Start Guide

4 Accessing via Web Browser

System Requirement:

Operating System: Microsoft Windows XP SP1 and above version

CPU: 2.0 GHz or higher

RAM: 1G or higher

Display: 1024×768 resolution or higher

Web Browser: Internet Explorer 8.0 and above version, Apple Safari

5.0.2 and above version, Mozilla Firefox 5.0 and above version and

Google Chrome 18 and above version

Steps:

1. Open the web browser.

2. In the browser address bar, input the IP address of the network

camera, and press the Enter key to enter the login interface.

Note:

 The default IP address is 192.168.1.64. You are recommended

to change the IP address to the same subnet with your

computer.

3. Input the user name and password.

The admin user should configure the device accounts and user/operator permissions properly. Delete the unnecessary accounts and user/operator permissions.

Note:

The device IP address gets locked if the admin user performs 7

failed password attempts (5 attempts for the user/operator).

Network Dome Camera·Quick Start Guide

4. Click Login.

5. Install the plug-in before viewing the live video and managing the

camera. Follow the installation prompts to install the plug-in.

Note:

You may have to close the web browser to finish the installation of the plug-in.

Download Plug-in

6. Reopen the web browser after the installation of the plug-in and

repeat steps 2 to 4 to login.

Note:

For detailed instructions of further configuration, please refer to the user manual of network camera.

Network Dome Camera·Quick Start Guide

5 Operating via Hik-Connect App

Purpose:

Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on.

Note:

Hik-Connect service is not supported by certain camera models.

5.1 Enable Hik-Connect Service on Camera

Purpose:

Hik-Connect service should be enabled on your camera before using the service.

You can enable the service through SADP software or web browser.

Enable Hik-Connect Service via SADP Software

Steps:

1. Check the checkbox of Enable Hik-Connect on:

1). "Activate the Device" page during camera activation, refer to

Chapter 3.2.2.

2). Or "Modify Network Parameters" page during modifying IP

address, refer to Chapter 3.3.

2. Create a verification code or change the verification code.

Network Dome Camera·Quick Start Guide

Verification Code Setting (SADP)

Note:

The verification code is required when you add the camera to

Hik-Connect app.

3. Click and read "Terms of Service" and "Privacy Policy".

4. Confirm the settings.

Enable Hik-Connect Service via Web Browser

Before you start:

You need to activate the camera before enabling the service. Refer to

Chapter 3.2.

Network Dome Camera·Quick Start Guide

Steps:

1. Access the camera via web browser. Refer to Chapter 4.

2. Enter platform access configuration interface: Configuration >

Network > Advanced Settings > Platform Access

Platform Access Configuration (Web)

3. Select Platform Access Mode as Hik-Connect.

4. Check the checkbox of Enable.

5. Click and read "Terms of Service" and "Privacy Policy" in pop-up

window.

6. Create a verification code or change the verification code for the

camera.

Note:

The verification code is required when you add the camera to

Hik-Connect app.

7. Save the settings.

Network Dome Camera·Quick Start Guide

5.2 Hik-Connect Setup

Steps:

1. Download and install the Hik-Connect app by searching

“Hik-Connect” in App Store or Google PlayTM.

2. Launch the app and register for a Hik-Connect user account.

3. Log in Hik-Connect app after registration.

5.3 Adding Camera to Hik-Connect

Before you start:

You need to enable the Hik-Connect service on camera before

adding it to your Hik-Connect account. Refer to Chapter 5.1.

Steps:

1. Use a network cable to connect the camera with a router if the

camera does not support Wi-Fi.

Figure 5-3 Connect a Router

Note:

After the camera connects to the network, please wait one minute before any operation on the camera using Hik-Connect app.

2. In the Hik-Connect app, tap “+” on the upper-right corner and

then scan the QR code of the camera to add the camera.

Network Dome Camera·Quick Start Guide

You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package.

Figure 5-4 Scan QR Code

Note:

If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number.

3. Input the verification code of your camera.

Note:

● The required verification code is the code you create or

change when you enabling Hik-Connect service on camera.

● If you forget the verification code, you can check the current

verification code on Platform Access configuration page via web browser.

4. Follow the prompts to set the network connection and add the

camera to your Hik-Connect account.

Note:

For detailed information, refer to the user manual of the Hik-Connect app.

Network Dome Camera·Quick Start Guide

5.4 Initializing the Memory Card

Check the memory card status by tapping on the Storage Status in the Device Settings interface.

If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start

recording any event triggered video in the camera such as motion detection.

Hikvision DS-2XC6122FWD-IS-2.8mm, DS-2XC6122FWD-IS-4mm, DS-2XC6122FWD-IS-6mm, DS-2XC6142FWD-IS-4mm, DS-2XC6142FWD-IS-6mm Quick Start Guide

Specifications and Main Features

Frequently Asked Questions

User Manual

1 Appearance Description

2 Installation

Install Memory Card

Ceiling Mounting

Wall Mounting

Wiring

Activating the Camera

Activation via Web Browser

Activation via SADP Software

Modifying the IP Address

4 Accessing via Web Browser

5 Operating via Hik-Connect App

5.1 Enable Hik-Connect Service on Camera

Enable Hik-Connect Service via SADP Software

Enable Hik-Connect Service via Web Browser

5.2 Hik-Connect Setup

5.3 Adding Camera to Hik-Connect

5.4 Initializing the Memory Card