Applicable Models
This manual is applicable to DS-3E0310HP series 100 Mbps Long-Range PoE switch.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol |
Description |
|
Provides additional information to emphasize or |
|
supplement important points of the main text. |
|
Indicates a potentially hazardous situation, which if not |
|
avoided, could result in equipment damage, data loss, |
|
performance degradation, or unexpected results. |
|
Indicates a hazard with a high level of risk, which if |
|
not avoided, will result in death or serious injury. |
|
|
•During the installation and utilization of the device, please strictly conform to electrical safety rules in di erent nations and regions.
•Use the attached power adaptor only and not to change the adaptor randomly. Please refer to specification table for specific requirements of power adaptor.
•Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)
•The device must be installed in machine room only, and only maintenance sta or qualified person should access to the device.
•Do not touch the upper cover area of the device that may be overheated.
•Power must be shut down during cable connection, device installation and dismantlement.
•You shall acknowledge that the use of the device with Internet access might be under network security risks, please strengthen protection for your personal information and datasecurity.Ifyoufindthedevicemightbeundernetworksecurityrisks,pleasecontact with us.
•Proper configuration of all passports and other security settings is the responsibility of the installer, and you shall keep user name and passports properly.
•Please keep all original packing materials properly. If the product does not work properly, pack the switch in its original packing materials for shipping. We shall not assume any responsibility for damages caused by improper packing materials during shipping.
•Ensure that your devices powered via the PoE port have their shells protected and
fire-proofed, because the switches are not compliant with the Limited Power Source (LPS) standard.
•This is a class A product and may cause radio interference in which case the user may be required to take adequate measures.
1
Packing List
Switch x 1 |
Power Adapter x 1 Power Cord x 1 Quick Start |
Guide x 1
If any accessories are damaged or lost, keep the package intact and contact your dealer for replacement.
Interfaces
Front Panel
PoE-MAX Indicator |
LINK/ACT |
PoE |
LINK/ACT |
|
PWR |
PoE Ports |
Indicator |
Indicator |
Indicator |
Indicator |
|
|
RJ45 Ports |
Hi-PoE |
PoE |
UPLINK |
Hi-PoE Port
Hi-PoE port is used for other Hi-PoE PTZ cameras connection, and the max. power is 60 W.
PoE Ports
100 Mbps PoE ports are used for other PoE devices connection.
RJ45 Ports
1000 Mbps RJ45 ports are used for devices connection via network cables.
2
Rear Panel
DIP Switch |
Grounding |
Power |
|
Terminal |
Supply |
||
|
|||
|
|
PWR |
|
OFF ON |
|
|
|
Extend |
|
DC 48V |
|
PORT 1-8 |
|
|
DIP Switch
ON: Extend mode, ports 1-8 support network transmission of up to 250 m, and the speed rate of the port is 10 Mbps.
OFF: Standard mode, the network transmission of PoE ports is up to 100 m, and the speed rate of the port is 100 Mbps.
Grounding Terminal
The grounding terminal is used to connect to the ground cable to protect the switch from lightning.
Power Supply
Use the attached power cord to connect the switch to socket.
3
Device Connection
Connect your devices according to your actual networking requirements.
Router
|
|
|
|
|
Dual uplink ports for |
NVR |
|
Monitor |
|
100 Mbps Long-Range PoE Switch |
|
|
|
||||||
|
|
CCTV scenario |
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Up to 250 meters
Camera
Hi-PoE
PTZ (60 W)
4 |
|
5 |
|
|
|