HIKVISION DS-2CZ232P, DS-2CM232N, DS-2CZ232N, DS-2CM232P, DS-2CZ252P Camera User Manual
...
1
Color Zoom Camera
USER’S MANUAL
Version 2.0.0
2
Thank you for purchasing our product. If there is any question or request, please do not hes it a te to contact dealer.
This manual is applicab le to DS-2CZ232P/N, DS-2CM232P/N, DS-2CZ252P/N, DS-2CM252P/N, DS-2CZ282P,
and DS-CZ292P series color zoom cameras.
This manual may contain several technically incorrect places or printing errors, and the content is subject to
change without notice. The updates will be added into the new version of this manual. We will readily improve or
update the products or procedures described in the manual.
3
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may cause if any of the warnings is neglected.
Cautions: Injury or equipment damage may caus e if any of the cautions is neglected.
Warnings Follow these safeguards
to prevent serious injury or
death.
Cautions
Follow these precautions
to prevent potential injury or
material damage.
Warnings
1. In the use of the product, you must be strict compliance with the electrical safety regulations of the nation and
region.
2. Input voltage should meet both the SELV(Safety Extra Low Voltage) and the Limited P ower Source with AC
24V or DC 12V according to the IEC60950－1 standard. Please refer to techn ical specifications for detail
information.
3. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazar d.
4. Please make sure that the plug is firmly connected on the power socket.
5. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
6. If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then
please contact the servi ce center.
7. If the product does not work pro perly, please contact your dealer o r the nearest ser vice center. Never attempt
to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by
unauthorized repair or maintenance.)
4
Cautions：
1. Make sure the power suppl y voltage is correct before usi ng the camera.
2. Do not drop the camera or subject it to physical shock.
3. Do not touch CCD (Charge Coupled Device) modules with fin gers. If cleaning i s necessary, use clean cloth
with a bit of ethanol and wipe it gently. If the camera will not be used for an extend ed period , please tu rn on
the lens cap to protect the CCD from dirt.
4. Do not aim the camera at the sun or extra bright places. A blooming or smear may occur otherwise (which is
not a malfunction however), and affecting the endurance of CCD at the same time.
5. The CCD may be burned out by a laser beam, so when any laser equipment is on using, make sure that the
surface of CCD will not be exposed to the laser beam.
6. Do not place the camera in extremely hot, cold(the operating temperature shall be－10℃～＋60℃ ), dusty
or damp locations, and do not expose it to high electromagnetism radiation.
7. To avoid heat accumulation, good ventilation is required for operating environment.
8. Keep the camera away from liquid while on using.
9. While on a delivery, the camera shall be packed in its original packing, or packin g of the same texture.
10. Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced
regularly according to their average enduring time. The average ti me varies because of differences b etween
operating environment and using history, so regular checking is recommended for all the users. Please
contact with your dealer for more details.
5
Table of Contents
C H A P T E R 1 ................................................................................................................................ 1
INTRODUCTION
.................................................................................................................................. 1
1.1
PRODUCT FEATURES ............................................................................................................................. 2
1.2
SIDE PLATE OF THE CAMERA ........................................................................................................... 2
1.3
REAR PLATE OF THE CAMERA ......................................................................................................... 3
1.4
CHIEF INTRODUCTION ABOUT FUNCTION ........................................................................................ 3
C H A P T E R 2
................................................................................................................................ 5
INSTALLATION
.................................................................................................................................... 5
2.1
LENS ............................................................................................................................................... 6
2.2
REAR PLATE DEFINITION ................................................................................................................. 6
2.3
POWER SU PP LY ................................................................................................................................ 6
C H A P T E R 3
................................................................................................................................ 7
MENU DESCRIPTION OF 232 SERIES
................................................................................................... 7
3.1
KEYS INTRODUCTION ...................................................................................................................... 8
3.1.1 Setting buttons
........................................................................................................................ 8
3.1.2 Zoom/Focus Wire Remote Control
.......................................................................................... 8
3.1.3 Alarm in, GND, Alarm output, Alarm output Com
................................................................... 9
3.1.4 Power supply
........................................................................................................................... 9
3.1.5 Interface Definition
.................................................................................................................. 9
3.2
OSD MENU CONFIGURATION ........................................................................................................ 10
3.2.1 Menu Structure
..................................................................................................................... 11
3.2.2 Exposure
................................................................................................................................ 12
3.2.3 Auto Gain Control
.................................................................................................................. 12
3.2.4 White Balance
....................................................................................................................... 12
3.2.5 Auto Focus
............................................................................................................................. 13
3.2.6 Day / Night
............................................................................................................................ 13
3.2.7 Motion Detection
.................................................................................................................. 14
3.2.8 Special Functions
................................................................................................................... 14
3.2.9 Exit
......................................................................................................................................... 16
C H A P T E R 4
.............................................................................................................................. 17
MENU DESCRIPTION OF 252 SERIES
................................................................................................. 17
4.1
KEYS INTRODUCTION .................................................................................................................... 18
4.1.1 Setting buttons
...................................................................................................................... 18
4.1.2 Zoom/Focus Wire Remote Control
........................................................................................ 18
4.1.3 Alarm in, GND, Alarm output, Alarm output Com
................................................................. 19
4.1.4 Power supply
......................................................................................................................... 19
4.1.5 Interface Definition
................................................................................................................ 19
6
4.2 OSD MENU CONFIGURATION ........................................................................................................ 20
4.2.1 Menu Structure
..................................................................................................................... 20
4.2.2 Shutter
................................................................................................................................... 22
4.2.3 Auto Gain Control
.................................................................................................................. 22
4.2.4 White Balance
....................................................................................................................... 23
4.2.5 Auto Focus
............................................................................................................................. 23
4.2.6 Day / Night
............................................................................................................................ 24
4.2.7 Motion Detection
.................................................................................................................. 25
4.2.8 Special Fuctions
..................................................................................................................... 25
4.2.9 Exit
......................................................................................................................................... 27
APPENDIX SPECIFICATION
................................................................................................................ 28
T
ABLE 1 DS-2CZ232P/N .................................................................................................................... 28
T
ABLE 2 DS-2CM232P/N ................................................................................................................... 29
T
ABLE 3 DS-2CZ252P/N .................................................................................................................... 30
T
ABLE 4 DS-2CM252P/N ................................................................................................................... 31
T
ABLE 5 DS-2CZ282P ........................................................................................................................ 32
T
ABLE 6 DS-2CZ292P ........................................................................................................................ 33
1
C H A P T E R 1
Introduction
2
1.1 Product Features
DS-2CZ232P(DS-2CM232P),DS-2CZ252P（DS-2CM252P）series are high per fo r mance cameras which adopt 1/4"
SONY Interline Transfer Super HAD CCD and advanced print circuit board design technology, and possess of
high resolution, lower distortion, and lower noise features. They are extremely suitable for surveillance system and
image process system.
Features:
• Digital signal process camera (DSP), 480TVL;
• DS-2CZ232P and DS-2CM232P series hold 22X optics variable focus and auto focus functions;
• DS-2CZ252P and DS-2CM252P series hold 23X Optics variable focus and auto focus functions;
• DS-2CZ232P and DS-2CM232P series with Iris F1.6, f=3.9-85.8mm;
• DS-2CZ252P and DS-2CM252P series with Iris F1.6, f=3.84-88.4mm;
• Support automatic electron shutter, auto iris/ manual iris, automatic/manual white balance;
• High S/N ra tio, support color black/white auto switch function;
• High color rendition;
• Support back light compensation, automatic electron gain;
• Support motion detec t io n;
•Support RS-485/wire remote control;
• Support OSD menu and parameters configuration;
• Support internal synchronization;
• Support PAL standard;
• DC12V±10% power supply;
1.2 Side Plate of the Camera
Figure 1.1 DS-2CZ232P side plate
3
Figure 1.2 DS-252P side plate
1.3 Rear Plate of the Camera
Figure 1.3 Rear plate of DS-232P and DS-252P
1.4 Chief Introduction about Function
Motion Detection: In the surveillance area, the appearing motion object will trigger alarm. User can select
suitable sensitivity level with corresponding environment.
Color B/W auto switch: The camera will displ ay color image and become monochrome automatically at night .
AGC: When object being shot look dim, please turn on AGC. It is propitious to enhance brightness. To output
standard video under different illumination, the range of auto gain control must be large enough. When under low
illumination, AGC will increase camera’s sensitivity, and output bright and clear video.
S/N ratio: It is the ratio of Signal voltage and noise voltage. The ratio is larger, the effect of noise is less, and the
image is more spotless.
4
OSD (On Scree n Display): The camera supports friend ly menu interface on the screen, and it’s convenient for
user selecting expected function.
White Balance: Because the camera cou ld not adjust the colo r temperature accordi ng to the light alteration as the
eyes, that will cause color deviation. White balance is the white rendition ability of the camera to adjust the
problem according to the environment automatically.
ICR Auto Switch: The filter will filter infrared light during the daytime and change to normal filter at night to
ensure a high sensitivity and clear image.
BLC: If there is glaring light in the background of the object being shot, the object will look very dim. In this
situation, turning on BLC function will make the object look bright and clear, but the background scene will be
overexposure.
BLC OFF BLC ON
5
C H A P T E R 2
Installation
6
Before mounting, please make sure that the device in th e package is in go od condition and all the assembl y parts
are complete.
2.1 Lens
The lens of the automatic focus ca mera were in stall ed i nsid e of the camera, 23 2 seri es cameras with f=3.9-85.8mm,
252 series cameras with f=3 .84-88.4mm.
2.2 Rear Plate Definition
Fig. 2.1 Rear plate definition of DS-2CZ232P and DS-2C252P
2.3 Power Supply
Before electrify the camera, please check the power supply. The power supply of the camera should be
DC12V±10%. Please refer to the specification for the details.
Loading...