HIKVISION DS-2CZ232P, DS-2CM232N, DS-2CZ232N, DS-2CM232P, DS-2CZ252P Camera User Manual

...

Color Zoom Camera

USER’S MANUAL

Version 2.0.0

Thank you for purchasing our product. If there is any question or request, please do not hes it a te to contact dealer. This manual is applicab le to DS-2CZ232P/N, DS-2CM232P/N, DS-2CZ252P/N, DS-2CM252P/N, DS-2CZ282P,

and DS-CZ292P series color zoom cameras.

This manual may contain several technically incorrect places or printing errors, and the content is subject to change without notice. The updates will be added into the new version of this manual. We will readily improve or update the products or procedures described in the manual.

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.

The precaution measure is divided into “Warnings” and “Cautions”

Warnings: Serious injury or death may cause if any of the warnings is neglected.

Cautions: Injury or equipment damage may caus e if any of the cautions is neglected.

Warnings Follow these safeguards

to prevent serious injury or death.

Cautions

Follow these precautions

to prevent potential injury or

material damage.

Warnings

1. In the use of the product, you must be strict compliance with the electrical safety regulations of the nation and region.

2. Input voltage should meet both the SELV(Safety Extra Low Voltage) and the Limited P ower Source with AC

24V or DC 12V according to the IEC60950－1 standard. Please refer to techn ical specifications for detail

information.

3. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazar d.

4. Please make sure that the plug is firmly connected on the power socket.

5. When the product is mounted on wall or ceiling, the device shall be firmly fixed.

6. If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then

please contact the servi ce center.

7. If the product does not work pro perly, please contact your dealer o r the nearest ser vice center. Never attempt

to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)

Cautions：

1. Make sure the power suppl y voltage is correct before usi ng the camera.

2. Do not drop the camera or subject it to physical shock.

3. Do not touch CCD (Charge Coupled Device) modules with fin gers. If cleaning i s necessary, use clean cloth

with a bit of ethanol and wipe it gently. If the camera will not be used for an extend ed period , please tu rn on

the lens cap to protect the CCD from dirt.

4. Do not aim the camera at the sun or extra bright places. A blooming or smear may occur otherwise (which is

not a malfunction however), and affecting the endurance of CCD at the same time.

5. The CCD may be burned out by a laser beam, so when any laser equipment is on using, make sure that the

surface of CCD will not be exposed to the laser beam.

6. Do not place the camera in extremely hot, cold(the operating temperature shall be－10℃～＋60℃ ), dusty

or damp locations, and do not expose it to high electromagnetism radiation.

7. To avoid heat accumulation, good ventilation is required for operating environment.

8. Keep the camera away from liquid while on using.

9. While on a delivery, the camera shall be packed in its original packing, or packin g of the same texture.

10. Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced

regularly according to their average enduring time. The average ti me varies because of differences b etween

operating environment and using history, so regular checking is recommended for all the users. Please

contact with your dealer for more details.

Table of Contents

C H A P T E R 1 ................................................................................................................................ 1

INTRODUCTION

.................................................................................................................................. 1

1.1

PRODUCT FEATURES ............................................................................................................................. 2

1.2

SIDE PLATE OF THE CAMERA ........................................................................................................... 2

1.3

REAR PLATE OF THE CAMERA ......................................................................................................... 3

1.4

CHIEF INTRODUCTION ABOUT FUNCTION ........................................................................................ 3

C H A P T E R 2

................................................................................................................................ 5

INSTALLATION

.................................................................................................................................... 5

2.1

LENS ............................................................................................................................................... 6

2.2

REAR PLATE DEFINITION ................................................................................................................. 6

2.3

POWER SU PP LY ................................................................................................................................ 6

C H A P T E R 3

................................................................................................................................ 7

MENU DESCRIPTION OF 232 SERIES

................................................................................................... 7

3.1

KEYS INTRODUCTION ...................................................................................................................... 8

3.1.1 Setting buttons

........................................................................................................................ 8

3.1.2 Zoom/Focus Wire Remote Control

.......................................................................................... 8

3.1.3 Alarm in, GND, Alarm output, Alarm output Com

................................................................... 9

3.1.4 Power supply

........................................................................................................................... 9

3.1.5 Interface Definition

.................................................................................................................. 9

3.2

OSD MENU CONFIGURATION ........................................................................................................ 10

3.2.1 Menu Structure

..................................................................................................................... 11

3.2.2 Exposure

................................................................................................................................ 12

3.2.3 Auto Gain Control

.................................................................................................................. 12

3.2.4 White Balance

....................................................................................................................... 12

3.2.5 Auto Focus

............................................................................................................................. 13

3.2.6 Day / Night

............................................................................................................................ 13

3.2.7 Motion Detection

.................................................................................................................. 14

3.2.8 Special Functions

................................................................................................................... 14

3.2.9 Exit

......................................................................................................................................... 16

C H A P T E R 4

.............................................................................................................................. 17

MENU DESCRIPTION OF 252 SERIES

................................................................................................. 17

4.1

KEYS INTRODUCTION .................................................................................................................... 18

4.1.1 Setting buttons

...................................................................................................................... 18

4.1.2 Zoom/Focus Wire Remote Control

........................................................................................ 18

4.1.3 Alarm in, GND, Alarm output, Alarm output Com

................................................................. 19

4.1.4 Power supply

......................................................................................................................... 19

4.1.5 Interface Definition

................................................................................................................ 19

4.2 OSD MENU CONFIGURATION ........................................................................................................ 20

4.2.1 Menu Structure

..................................................................................................................... 20

4.2.2 Shutter

................................................................................................................................... 22

4.2.3 Auto Gain Control

.................................................................................................................. 22

4.2.4 White Balance

....................................................................................................................... 23

4.2.5 Auto Focus

............................................................................................................................. 23

4.2.6 Day / Night

............................................................................................................................ 24

4.2.7 Motion Detection

.................................................................................................................. 25

4.2.8 Special Fuctions

..................................................................................................................... 25

4.2.9 Exit

......................................................................................................................................... 27

APPENDIX SPECIFICATION

................................................................................................................ 28

ABLE 1 DS-2CZ232P/N .................................................................................................................... 28

ABLE 2 DS-2CM232P/N ................................................................................................................... 29

ABLE 3 DS-2CZ252P/N .................................................................................................................... 30

ABLE 4 DS-2CM252P/N ................................................................................................................... 31

ABLE 5 DS-2CZ282P ........................................................................................................................ 32

ABLE 6 DS-2CZ292P ........................................................................................................................ 33

C H A P T E R 1

Introduction

1.1 Product Features

DS-2CZ232P(DS-2CM232P),DS-2CZ252P（DS-2CM252P）series are high per fo r mance cameras which adopt 1/4" SONY Interline Transfer Super HAD CCD and advanced print circuit board design technology, and possess of high resolution, lower distortion, and lower noise features. They are extremely suitable for surveillance system and image process system. Features:

• Digital signal process camera (DSP), 480TVL;

• DS-2CZ232P and DS-2CM232P series hold 22X optics variable focus and auto focus functions;

• DS-2CZ252P and DS-2CM252P series hold 23X Optics variable focus and auto focus functions;

• DS-2CZ232P and DS-2CM232P series with Iris F1.6, f=3.9-85.8mm;

• DS-2CZ252P and DS-2CM252P series with Iris F1.6, f=3.84-88.4mm;

• Support automatic electron shutter, auto iris/ manual iris, automatic/manual white balance;

• High S/N ra tio, support color black/white auto switch function;

• High color rendition;

• Support back light compensation, automatic electron gain;

• Support motion detec t io n;

•Support RS-485/wire remote control;

• Support OSD menu and parameters configuration;

• Support internal synchronization;

• Support PAL standard;

• DC12V±10% power supply;

1.2 Side Plate of the Camera

Figure 1.1 DS-2CZ232P side plate

Figure 1.2 DS-252P side plate

1.3 Rear Plate of the Camera

Figure 1.3 Rear plate of DS-232P and DS-252P

1.4 Chief Introduction about Function

Motion Detection: In the surveillance area, the appearing motion object will trigger alarm. User can select

suitable sensitivity level with corresponding environment.

Color B/W auto switch: The camera will displ ay color image and become monochrome automatically at night .

AGC: When object being shot look dim, please turn on AGC. It is propitious to enhance brightness. To output

standard video under different illumination, the range of auto gain control must be large enough. When under low illumination, AGC will increase camera’s sensitivity, and output bright and clear video.

S/N ratio: It is the ratio of Signal voltage and noise voltage. The ratio is larger, the effect of noise is less, and the image is more spotless.

OSD (On Scree n Display): The camera supports friend ly menu interface on the screen, and it’s convenient for user selecting expected function.

White Balance: Because the camera cou ld not adjust the colo r temperature accordi ng to the light alteration as the eyes, that will cause color deviation. White balance is the white rendition ability of the camera to adjust the problem according to the environment automatically.

ICR Auto Switch: The filter will filter infrared light during the daytime and change to normal filter at night to ensure a high sensitivity and clear image.

BLC: If there is glaring light in the background of the object being shot, the object will look very dim. In this situation, turning on BLC function will make the object look bright and clear, but the background scene will be overexposure.

BLC OFF BLC ON

C H A P T E R 2

Installation

Before mounting, please make sure that the device in th e package is in go od condition and all the assembl y parts are complete.

2.1 Lens

The lens of the automatic focus ca mera were in stall ed i nsid e of the camera, 23 2 seri es cameras with f=3.9-85.8mm, 252 series cameras with f=3 .84-88.4mm.

2.2 Rear Plate Definition

Fig. 2.1 Rear plate definition of DS-2CZ232P and DS-2C252P

2.3 Power Supply

Before electrify the camera, please check the power supply. The power supply of the camera should be DC12V±10%. Please refer to the specification for the details.

C H A P T E R 3

Menu Description of 232 series

The menu functions of the DS-2CZ232P/N will be introduce d in this chapter. The first part is the instruction of keys and menu structure, the second part is to introduce the menu functions of all the items.

3.1 Keys Intro ducti o n

In this section, it will introduce the keys on the rear plate.

3.1.1 Setting buttons

Fig 3.1 The keys of camera

There are two work modes for the setting buttons: Common and Menu modes. Each of them has its own function.

Common mode: T/W button: Tele/ wide zoom operation. N/F button: Manual variable zoom, near/ far. Menu button: Menu mode switch. Pressing MENU key for 2 seconds, it will enter menu setting mode.

Menu mode: T/W button: Move the cursor up/down. N/F button: Move the cursor left/right. Menu button: Select options, and confirm the current value.

3.1.2 Zoom/Focus Wire Remote Control

“ ” RS-485, support PELCO -D protocol.

Default setting requirements:

 Signal transmission speed:2400bit/s  Protocol: PELCO-D  Data bit: 8bit  Stop bit: 1bit  Parity bit: None

3.1.3 Alarm in, GND, Alarm output, Alarm output Com

“ ” When motion detection module detects moving objects, it will trigger alarm signal.

3.1.4 Power supply

“ ” B efo r e connecting power supply adapter to camera, please check the anode and cathode.

3.1.5 Interface Definition

DS-2CZ232P interface definition:

Z “ ”

Zoom (Wire Control Port)

C “ ”

COM (Wire Control Port)

F “ ”

Focus (Wire Control Port)

IN/GND“ ”

Alarm Input/GND

OUT/COM “ ”

Alarm O utput/COM

D+/D- “ ”

485+/-

GND “ ”

Common GND

Fig 3.2 DS-2CZ232P interface definition table

Note: Z/F working voltage is: +3V to +12V, - 3V to -12 V.

Alarm output: Open Collector: Drive load is DC24V 45mA Max.

DS-2CM232P interface definition:

Fig 3.3 DS-2CM232P interface definition table

3.2 OSD Menu Configuration

In this section, it will introduce the menu of DS-2CZ232P. Pressing button for two seconds will enter main menu. The left is Menu items; the right is M enu items value. “…” means this option has a submenu, “---”

means this option cannot be set.

Fig 3.4 Main Menu

Pin number Name Voltage

1 Rx CMOS 5V,series receive pin 2 Tx CMOS 5V,series send pin

3 GND Series GND 4 DC IN 12VDC±10%

5 GND Power supply GND 6 CVBS OUT 1.0V±0.2V Video O ut p ut 7 GND Composite Video GND

8 NC 9 GND

Main Menu CAM ID 001 Shutter Auto AGC -- WB Auto1 AF Auto… D/N Auto… Motion D Close Special … Exit Abort

3.2.1 Menu Structure

1. CAM ID OFF/001~254，Edit camera ID number

2. Exposure Auto：Auto mode, Auto Iris,AGC , AES 1/50 AI…：Auto Iris, AGC, AES (1/50~1/10000) AE…：AES,AGC(Low、High、Close),AI(F1.6～F5.6) Manual…：Shutter, IRIS,AGC can be set by manual.

3. AGC Low/High/Close, if the exposure mode is Auto or AI, AGC will not be set ,it display “---”

4. WB ATW1/ATW2/Auto/Manual…

5. AF Auto…:To enter submenu and set the focus mode, sensitivity and the least focus distance ---

(1cm、50cm、1m) Manual One focus: triggered by button once, then turn to manual mode.

6. Color/ B/W Auto…:Color and B/W auto switch mode Color… B/W…

7. Motion D Close/Open…:To enter submenu and set motion detection sensitivity and areas

8. Special Press Menu button enter special function submenu（CN/EN,BLC,RS-485,POS/NEG, ZSpeed, Definition, Line Control ）

9. Exit Abort/Save/Default

Fig 3.5 Main Menu set

Fig 3.6 Special Menu set

(Special)

1. CN/EN EN

2. BLC Close: Turn off BLC Default…: Default BLC mode User…:user self-definition, the BLC areas position and size can be set

3. RS-485 485 communication parameter,to enter submenu to set RS-485 communication protocols, Baud and RS-485 address

4. POS/NEG ＋/-

5. ZSpeed Zoom speed:1～4 class

6. Define Definition ,1～5 class

7. Back

Fig 3.7 Main Menu structure

3.2.2 Exposure

The iris can control output video signal according to the different intensity of light. (This product is already equipped with iris.) The “F”(F1.6～F5.6) value of the iris can be set by user.

Fig 3.8 Exposure setup

Under AES and Manual mode, Iris can be set from F1.6 to F5.6 in exposure menu. Under AI and Manual mode, shutter can be set from 1/50s to 1/10Ks (8 options).

3.2.3 Auto Gain Control

When enable AGC in the situation of Manual and AES, there are three AGC options: Low, High and Off. When under AI and Manual modes, AGC is not available.

3.2.4 White Balance

In the “WB” options, user can set the white balance function to ensure it can render normal white in any color

1. AI… Manual shutter 1/50、1/120、1/250、1/500、1/1000、1/2000、1/4000、1/10000

2. AES… Manual Iris F1.6-----------1 /F5.6-----------1

3. Manual... Manual shutter 1/50、1/120、1/250、1/500、1/1000、1/2000、1/4000、1/10000 Manual Iris F1.6-----------1/F5.6----------1

4. Auto

Main Menu CAM ID OFF/001—254 Shutter Auto/AI…/AE…/Manual… AGC Low/High/Close WB ATW1/ATW2/Auto/Manual… AF Auto…/Manual/One Focus Color/B/W Color…/Auto…/B/W… Motion D Open…/Close Special … Exit Default/Abort/Save

temperature. If selecting th e ATW mode, the camera will continue moni toring the color temper ature according to the surrounding light and adjust WB based on the color temperature. Including ATW1, ATW2, Auto, and Manual modes.

Fig 3.9 white balance setup

ATW1: Camera recover color automatically based on TTL algorithm, temperature range is approximate from 2500K to 9300K. ATW2 : C amera recover color automatically based on TTL algorithm, temperature range is approximate from 2000K to 10000K. ATC: Adjust under steady colo r temperature envir onment. After sel ecting ATC, the white balance will take effect to the current scene, and adjust the temperature to 6500K. Manual: Adjust red and blue values to setup whi te balance.

3.2.5 Auto Focus

In the options of AF, user can select the Focus modes including Auto, Manual, One focus. Auto: it can accomplish continuous surveillance without manual adjustment. Manual: User can manual focus. One focus: Press the button to focus once, then it will be the same as manual mode.

Figure 3.10 AF Setup

3.2.6 Day / Night

Optional D/N modes: Auto D/N, Day, Night mode.

Note: The Auto mode requires meeting any of the following conditions:

(a). The exposure mode should be Auto or AI.

Setup User/3200K/6300K RED （+1F）--------|---------Blue (-53 ) -|-----------------Back

AF Setup Mode Normal/Interval Sense High/Mid/Low Near Lim 50cm/1m/1cm Back

WB ATW1/ATW2/Auto/Manual…

(b). If the exposure mode is manual or AE, the AGC should be set as High.

3.2.7 Motion Detection

In Motion Detection, the Motion D functions, sensitivity and motion areas can be set by manual. After the setup, user can detect the motion situation of the intruder.

The motion D has two work modes: When Motion D is Close, if alarm input occurs, the alarm output will directly respond. When Motion D is Open, the camera will auto detect monitoring area, and out put alarm signal.

3.2.8 Special Functions

User can set the CN/EN lan guage, RS-485, BLC, Zoom Speed, Definition, POS/NEG and Line control.

Fig 3.11 Special Function sets

CN/EN Setup:

Move cursor to “CN / EN” through up / down, and press left / right to select CN or EN.

BLC Setup:

The options have User…/Close/Default… Note: This function is only available when “Auto” selected in Exposure. The setup will retain when other options selected in Exposure. When “Default” is selected, the camera will adjust according to the default region. Press “MENU” to see the default back light area, an d press “MENU” again to exit. When select “USER”, user can customize the back light area. When entering adjust status, use up/down/left/right to adjust the back light area position. Press “MENU” once to release, use up/down/l eft/ r ight to change to area adjustment status, press “MENU” for 2 min to exit.

Special F unction CN/EN EN BLC User…/Close/Default… RS-485 … POS/NEG +/- ZSpeed 1/ 2/ 3/ 4 Define 1/ 2/ 3/ 4/ 5 Line Mode1/Mode2

Back

Figure 3.12 BLC

When select “Off”, camera will no t take back light compensatio n.

RS-485

Press MENU button to enter RS485 setup interface:

Figure 3.13 RS-485 Setup Interface

POS/ NEG

Move cursor to “POS / NEG”, and press left / right to select POS or NEG. Selecting “+”, the vid eo will be n o rmal, while selecting “-”, the video will be negative.

Zoom S peed

Move cursor to “Z Speed”, and press left/right to select from “1/2/3/4”. 1 means the slowest speed, and 4 means the fastest speed.

Definition

Move cursor to “Definition”, and press left/right to select High, Middle, 低中, and low to adjust the image definition.

Line Control

Move cursor to “Wire Remote Control”, and press left/right to select “Mode1/Mode2”. Mode1 is: When Vz-Vc=12V, wide-angle direction zooming. When Vz-Vc=-12V, tele direction zooming; Mode 2 is on the opposite.

Right,Up Button

RS485 Protocol PELCO-D Baud 2400 (1200, 2400, 4800, 9600, 19200, 38400, 115200 optional) Address 001 (000 to 254 optional) Back

3.2.9 Exit

Exit option is used for quit setting Menu, and return to normal work mode. Abort: Neglect all modifications, and resume the original setup. Save: Save all modifications. Default: Neglect all modifications, resume the default factory setup.

C H A P T E R 4

Menu Description of 252 series

The menu functions of the DS-2CZ232P will be introduced in this chapter. The first part is the instruction of keys and menu structure, the second part is to introduce the menu functions of all the items.

4.1 Keys Intro ducti o n

In this section, it will introduce the keys on the rear plate.

4.1.1 Setting buttons

Fig 4.1 The keys of camera

There are two work modes for the setting buttons: Common and Menu modes. Each of them has its own function.

Common mode: T/W button: Tele/ wide zoom operation. N/F button: Manual vari able zoom, near/ far. Menu button: Menu mode switch. Pressing MENU key for 2 seconds, it will enter menu setting mode.

Menu mode: T/W button: Move the cursor up/down. N/F button: Move the cursor left/right. Menu button: Select options, and confirm the current value.

4.1.2 Zoom/Focus Wire Remote Control

“ ” RS-485, support PELCO -D protocol.

Default setting requirements:

 Signal transmission speed:2400bit/s  Protocol: PELCO-D  Data bit: 8bit  Stop bit: 1bit  Parity bit: None

4.1.3 Alarm in, GND, Alarm output, Alarm output Com

“ ” When motion detection module detects moving objects, it will trigger alarm signal.

4.1.4 Power supply

“ ” Before connecting power supply adapter to camera, please check the anode and

cathode.

4.1.5 Interface Definition

DS-2CZ252P interface definition:

Z “

”

Zoom (Wire Control Port)

C “ ”

COM (Wire Control Port)

F “ ”

Focus (Line Control Port)

IN/GND“ ”

Alarm Input/GND

OUT/COM “ ”

Alarm Output/COM

D+/D- “ ”

485+/-

GND “ ”

Common GND

Fig 4.2 DS-2CZ252P interface definition table

Note: Z/F working voltage is: +3V to +12V, -3V to -12V.

Alarm output: Open Collector: Drive load is DC24V 45mA Max.

DS-2CM252P interface definition

Fig 4.3 DS-2CM252P interface definition table

4.2 OSD Menu Configuration

In this section, it will introduce the menu of DS-2CZ252P. Pressing button for two seconds will enter main menu. The left is Menu items; the right is M enu items value. “…” means this option has a submenu, “---”

means this option cannot be set.

Figure 4.4 Main Menu

4.2.1 Menu Structure

1. CAM ID OFF/001~254，Edit camera ID number

2. Shutter Auto：Auto mode, Auto Iris,AGC , AES 1/50 AI…：Auto Iris, AGC, AES (1/50~1/10000) AE…：AES,AGC(Low、High、Close),AI(F1.6～F5.6)

Pin number Name Voltage

1 Rx CMOS 5V,series receive pin 2 Tx CMOS 5V,series send pin

3 GND Series GN D 4 DC IN 12VDC±10%

5 GND Power supply GND 6 CVBS OUT 1.0V±0.2V Video O ut p ut 7 GND Composite Video GND

8 NC 9 GND

Main Menu CAM ID 001 Shutter Auto AGC -- WB Auto1 AF Auto… D/N Auto… Motion D Close Special … Exit Abort

Manual…：Shutter, IRIS, AGC can be set by manual.

3. AGC Low/High/Close, if the exposure mode is Auto or AI, AGC will not be set ,it display “---”

4. WB ATW1/ATW2/Auto/Manual…

5. AF

Auto…:To enter submenu and set the focus mode, sensitivity and the least focus distance

--- (1cm、50cm、1m) Manual One focus: triggered by button once, then turn to manual mode.

6. D/N Auto…: Day and night auto switch mode Day…: Enter sub menu to set saturation Night…: Enter sub menu to set color synchronization

7. Motion D Close/Open…:To enter submenu and set motion detection sensitivity and areas

8. Special Press Menu button enter special function submenu（ CN/EN,BLC,RS-485,POS/NEG, ZSpeed, Definition, Line ）

9. Exit Abort/Save/Default

Fig 4.5 Main menu set

Fig 4.6 Special Menu set

(Special)

1. CN/EN EN

2. BLC Close: Turn off BLC Default…: Default BLC mode User…:user self-definition, the BLC areas position and size can be set

3. RS-485 485 communication parameter to enter submenu to set RS-485 communication protocols, Baud and RS-485 address

4. POS/NEG ＋/-

5. ZSpeed Zoom speed:1～4 class

6. Define Definition ,1～5 class

7. Line Mode1/Mode2

8. Back

Fig 4.7 Main Menu structure

4.2.2 Shutter

The iris can control output video signal according to the different intensity of light. (This product is already equipped with iris.) The “F”(F1.6～F5.6) value of the iris can be set by user.

Fig 4.8 Exposure setup

Under AES and Manual mode, Iris can be set from F1.6 to F5.6 in exposure menu. Under AI and Manual mode, shutter can be set from 1/50s to 1/10Ks (8 options).

4.2.3 Auto Gain Control

When enable AGC in the situation of Manual and AES, there are three AGC options: Low, High and Off.

When under AI and Manual modes, AGC is not available.

1、AI… Manual shutter 1/50、1/120、1/250、1/500、1/1000、1/2000、1/4000、

1/10000

2、AES… Manual Iris F1.6-----------1 /F5.6-----------1 3、Manual... Manual shutter 1/50、1/120、1/250、1/500、1/1000、1/2000、1/4000、1/10000

Manual Iris F1.6-----------1/F5.6----------1

4、Auto

Main Menu CAM ID OFF/001—254 Shutter Auto/AI…/AE…/Manual… AGC Low/High/Close WB ATW1/ATW2/Auto/Manual… AF Auto…/Manual/One Focus D/N Day…/Auto…/Night… Motion D Open…/Close Special … Exit Default/Abort/Save

4.2.4 White Balance

In the white balance options, user can set the white balance function to ensure it can render normal white in any color temperature. If selecting the ATW mode, the camera will continue monitoring the color temperature according to the surrounding light and adjust WB based on the color temperature. Including ATW1, ATW2, Auto, and Manual modes.

Fig 4.9 white balance setup

ATW1: Camera recover color automatically based on TTL algorithm, temperature range is approximate from 2500K to 9300K. ATW2: Camera recover color automatically based on TTL algorithm, temperature range is approximate from 2000K to 10000K. ATC: Adjust under steady colo r temperature enviro nment. After select ing ATC, the white balance will take effect to the current scene, and adjust the temperature to 6500K. Manual: Adjust red and blue values to setup whi te balance.

Figure 4.10 MWB setup

4.2.5 Auto Focus

Figure 4.11 Auto Focus Setup

Setup User/3200K/6300K RED （+1F）--------|---------- Blue (-53 ) -|-----------------Back

AF Mode Normal/Interval Sense High/Mid/Low Near Lim 50cm/1m/1cm Back

WB ATW1/ATW2/Auto/Manual…

4.2.6 Day / Night

Optional day to night modes: Auto day switch to night, day mode, night mode. Auto day switch to night: Camera will switch between color and B/W according to the environment illumination. Under low illumination condition, IR filter will move away and switch to B/W mode to improve the sensitivity. Day Mode: IR filter will move into, the image back to normal status. Night Mode: IR filter will move away, the image will change to black and white status to improve sensitivity.

Figure 4.12 Night setup

Burst: Off: Do not output chroma signal and black and white composite video signal On: Output chroma signal.

Fig 4.13 Day setup

Chroma: Adjust chroma parameters, has low/mid/high options.

Figure 4.14 Auto D/N setup

Value: The threshold for day mode change to night mode. C/BW: The delay time for color change to black and white mode. BW/C: The delay time for black and white mode change to color mode.

Night Setup Burst Off/On Back

Day Setup Chroma High/Mid/Low Back

Auto D/N Value (2)------l----C/BW 2s/3s/5s/10s/15s/20s/25s/30s BW/C 2s/3s/5s/10s/15s/20s/25s/30s Back

4.2.7 Motion Detection

In Motion Detection, the Motion D functions, sensitivity and motion areas can be set by manual. After the setup, user can detect the motion situation of the intruder.

4.2.8 Special Fuctions

User can set the CN/EN lan guage, RS-485, BLC, ZoomSpeed, Definition ,POS/NEG, Line by manual.

Figure 4.15 Special Function sets

CN/EN Setup:

Move cursor to “CN / EN” through up / down, and press left / right to select CN or EN.

BLC Setup:

The options have User…/Clos e/Default… Note: This function is only available when “Auto” selected in Exposure. The setup will retain when other options selected in Exposure. When “Default” is selected, the camera will adjust according to the default region. Press “MENU” to see the default back light area, an d press “MENU” again to exit. When select “USER”, user can customize the back light area. When entering adjust status, use up/down/left/right to adjust the back light area position. Press “MENU” once to release, use up/down/left/right to change to area adjustment status, press “MENU” for 2 min to exit.

Special Function CN/EN EN BLC User…/Close/Default… RS-485 … POS/NEG +/ZSpeed 1/ 2/ 3/ 4 Define 1/ 2/ 3/ 4/ 5 Line Mode1 Back

Figure 4.16 BLC

When select “Off”, camera will no t take back light compensatio n.

RS-485

Press MENU button to enter RS485 setup interface:

Figure 4.17 RS-485 Setup Interface

POS/ NEG

Move cursor to “POS / NEG”, and press left / right to select POS or NEG. Selecting “+”, the video will be normal, while selecting “-”, the video will be negative.

Zoom S peed

Move cursor to “Z Speed”, and press left/right to select from “1/2/3/4”. 1 means the slowest speed, and 4 means the fastest speed.

Definition

Move cursor to “Definition”, and press left/right to select from 5 levels to adjust the image definition.

Line Control

Right Up Button

RS485 Protocol PELCO-D Baud 2400 （1200、2400、4800、9600、19200、38400、115200 optional） Address 001 （000---254 optio na l） Back

4.2.9 Exit

Exit option is used for quit setting Menu, and return to normal work mode.

Abort: Neglect all modifications, and resume the original setup.

Save: Save all modifications.

Appendix Specification

Table 1 DS-2CZ232P/N

Parameter Model DS-2CZ232P/N

Image Sensor 1/4 inch SONY Interline Transfer Super HAD CCD Signal System PAL/NTSC

Effective Pixels

PAL: 752 (H) × 582 (V)

NTSC: 768 (H) × 494 (V) Synchronization Internal Synchronization Horizontal Resolution 480 TVL Video Output 1Vp-p Composite Output (75Ω/BNC) S/N Ratio More than 50dB Day & Night (Electronic) Auto / Color / B&W Min. Illumination 0.1Lux @ F1.6 Lens 22X Optical Zoom

F1.6, f=3.9 ~ 85.8mm

Min. Working Distance: 10-1000mm(Wide-Tele) Menu Camera ID On / Off (001-254, fixed position)

Language English, Chinese Iris Auto / Manual Electronic Shutter 1/50(1/ 60) s to 1/ 1 00 , 0 00s

Auto Gain Low / High / Off Auto Focus Auto / Manual / Once Auto White Balance ATW1 / ATW2 /Auto / Manual( Pre-set 3200K, Pre -set 5600K, R / G

Gain Correction)

Motion Detection On / Off (Zone, Sensitivity) Special Function BLC, POS/NEG, Zoom Speed (4 levels), Definition

Communication Interface

RS-485, PELCO-D, Baud Rate, Address, PTZ Control

Power Supply 12VDC, ±10% Working Temperature -10℃ ~ 60℃ Power Consumption 4.5W Dimension (mm)

64 × 61 × 112.5

(2.53” × 2.42” × 4.46”)

Weight

375g

(0.82lbs)

Table 2 DS-2CM232P/N

Parameter Model DS-2CM232P/N

Image Sensor 1/4 inch SONY Interline Transfer Super HAD CCD Signal System PAL/NTSC

Effective Pixels

PAL: 752 (H) × 582 (V)

Lens

22X Optical Zoom

F1.6, f=3.9 ~ 85.8mm

Min. Working Distance:10-1000mm(Wide-Tele)

Camera ID On / Off (001-254, fixed position) Language English, Chinese Iris Auto / Manual

Electronic Shutter 1/50(1/ 60) s to 1/ 1 00 , 0 00s

Auto Gain Low / High / Off Auto Focus Auto / Manual / Once Day & Night (Electronic)

Auto / Color / B&W

Auto White Balance

ATW1 / ATW2 /Auto / Manual( Pre-set 3200K, Pre -set 5600K, R / G

Gain Correction)

Motion Detection On / Off (Zone, sensitivity)

Special Function BLC, POS/NEG, Zoom speed(4 levels), Definition

Communication Interface

HIKVISION protocol, compatible of SONY VISCA protocol

Power Supply 9-12V DC Working Temperature -10℃ ~ 60℃ Power Consumption 4W Max Dimension (mm) 50 × 55.6 × 86 Weight 235g

Table 3 DS-2CZ252P/N

Parameter Model DS-2CZ252P/N

Image Sensor 1/4 inch SONY Interline Transfer Super HAD CCD Signal System PAL/NTSC Effective Pixels PAL: 752 (H) × 582 (V)

NTSC: 768 (H) × 494 (V) Synchronization Internal Synchronization Horizontal Resolution Color: 480 TVL

B / W: 520 TVL Video Output 1Vp-p Composite Output (75Ω/BNC) S/N Ratio More than 50dB Day & Night IR Cut Filter Auto Switch Min. Illumination Color: 0.2Lux @ F1.6

B / W: 0.02Lux @ F1.6 Lens 23X Optical Zoom

F1.6, f=3.84 ~ 88.4mm

Min. Working Distance:10-1200mm(Wide-Tele) Menu Camera ID On / Off (001-254, fixed position)

Language English, Chinese Iris Auto / Manual Electronic Shutter 1/50 (1/60s) to 1/100,000s

Auto Gain Low / High / Off Auto Focus Auto / Manual / Once Auto White Balance ATW1 / ATW2 /Auto / Manual( Pre-set 3200K, Pre -set 5600K, R / G

Gain Correction)

Motion Detection On / Off (Zone, Sensitivity) Special Function BLC, POS/NEG, Zoom Speed (4 levels), Definition

Communication Interface

RS-485, PELCO-D, Baud Rate, Address, PTZ Control (Optional Mode)

Power Supply 12VDC, ±10% Working Temperature -10℃ ~ 60℃ Power Consumption 4.5W Dimension (mm)

68.7 × 66.1 × 125 (2.7” × 2.6” × 4.9”)

Weight 550g (1.21lbs)

Table 4 DS-2CM252P/N

Parameter Model DS-2CM252P/N

Image Sensor 1/4 inch SONY Interline Transfer Super HAD CCD Signal System PAL/NTSC Effective Pixels PAL: 752 (H) × 582 (V)

NTSC: 768 (H) × 494 (V) Synchronization Internal Synchronization Horizontal Resolution Color: 480 TVL

B / W: 520 TVL Video Output 1Vp-p Composite Output (75Ω/BNC) S/N Ratio More than 50dB Day & Night IR Cut Filter Auto Switch Min. Illumination Color: 0.2Lux @ F1.6

B / W: 0.02Lux @ F1.6 Lens 23X Optical Zoom

F1.6, f=3.84 ~ 88.4mm

Min. Working Distance:10-1200mm(Wide-Tele) Menu Camera ID On / Off (001-254, fixed position)

Language English, Chinese Iris Auto / Manual Electronic Shutter 1/50(1/ 60) s to 1/ 1 00 , 0 00s

Auto Gain Low / High / Off Auto Focus Auto / Manual / Once Auto White Balance ATW1 / ATW2 /Auto / Manual( Pre-set 3200K, Pre -set 5600K, R / G

Gain Correction)

Motion Detection On / Off (Zone, Sensitivity) Special Function BLC, POS/NEG, Zoom Speed (4 levels), Definition

Communication Interface

HIKVISION protocol, compatible of SONY VISCA protocol

Power Supply 12VDC, ±10% Working Temperature -10℃ ~ 60℃ Power Consumption 4W MAX Dimension (mm)

61.2 × 50 × 88.3

Weight 370g

Table 5 DS-2CZ282P

Parameter Model DS-2CZ282P

Image Sensor 1/4"SONY Interline Transfer Super HAD CCD Signal System PAL Effective Pixels 752(H)×582(V) Synchronous Internal Synchronization

Horizontal Resolution

Day:540TVL

Night:600TVL Privacy 16 areas (area/position adjustable) Video Output 1.0Vp-p Composite Output(75Ω/BNC) S/N Ratio More than 52dB Day & Night IR Cut Filter Auto Switch

Min. Illumination

Day: 0.2Lux @ F1.4, 0.008Lux @ F1.4 (sensitivity×256)

Night: 0.02Lux @ F1.4, 0.0008Lux @ F1.4 (sensitivity×256)

Lens

Total Zoom 480X,Optical Zoom:30X, Digital Zoom:16X

F1.4, f=3.5 - 105mm

Min. Working Distance:10-1500mm(Wide-Tele)

Camera ID On/ Off (OSD, 001-254, on the top right corner) Language Chinese /English Iris Auto/Manual Electronic Shutter 1/50S-1/10,000S Auto Gain Low/High/Close Auto Focus Auto/Manual/One focus Day/Night Auto/Day/Night

Auto White Balance ATW1/ATW2/AC/Manual(3200K,6300K,R/G gain adjust)

Motion Detection OFF/ON（area, sensitivity）

Special Function

Optical Zoom, BLC,Y-Value, C-Value, POS/NEG, ZSp eed (4 Class),

Definition, Mirror, Digital Noise Reduction

Communication Interface RS-485,PELCO-P/D, Baud, Address, PTZ Control

Power Supply DC12V±10% Working Temper ature -10℃--60℃ Power Consumption 4.5W MAX Dimension (mm) 124×66×68.5 Weight 450g

Table 6 DS-2CZ292P

Parameter Model DS-2CZ292P

Image Sensor 1/4"SONY Interline Transfer Super HAD CCD Signal System PAL Effective Pixels 752(H)×582(V) Synchronous Internal Synchronization

Horizontal Resolution

Day:540TVL

Night:600TVL Privacy 16 areas(area/position adjustable) Video Output 1.0Vp-p Composite Output(75Ω/BNC) S/N Ratio More than 52dB Day & Night IR Cut Filter Auto Switch

Min. Illumination

Day:0.2Lux @ F1.6,0.008Lux @ F1.6(sensitivity×256)

Night :0.02Lux @ F1.6,0.0008Lux @ F1.6 (sensitivity×256)

Lens

Total Zoom:576X,Optical Zoom:36X, Digital Zoom:16X

F1.6, f=3.4 - 122.4mm

Min. Working Distance: 10-1500mm(Wide-Tele)

Camera ID On/Off (OSD, 001-254, on the top right corner) Language Chinese /English Iris Auto/Manual Electronic Shutter 1/50S-1/10,000S Auto Gain Low/High/Close Auto Focus Auto/Manual/One focus Day/Night Auto/Day/Night

Auto White Balance ATW1/ATW2/AC/Manual(3200K,6300K,R/G gain adjust)

Motion Detection OFF/ON(area, sensitivity)

Special Function

Optical Zoom, BLC,Y-Value, C-Value, POS/NEG, ZSp eed(4 Class),

Definition, Mirror, Digital Noise Reduction

Communication Interface RS-485,PELCO-D, Baud, Address, PTZ Control

Power Supply DC12V±10% Working Temperature -10℃--60℃ Power Consumption 4.5W MAX Dimension (mm) 124×66×68.5 Weight 450g

HIKVISION DS-2CZ232P, DS-2CM232N, DS-2CZ232N, DS-2CM232P, DS-2CZ252P Camera User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual