TurboHD
Turret Camera
DS-2CE71D0T-PIRL
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, please contact the dealer.
This manual may contain technical incorrect places or
printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or update
the products or procedures described in the manual.
Regulatory Information FCC Information
Please take attention that changes or modification not
expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
FCC Compliance: This equipment has been tested and
found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
EU Conformity Statement
This product and, if applicable, the supplied
accessories too are marked with “CE” and comply
European standards listed under the Low Voltage Directive
2014/35/EU, the EMC Directive 2014/30/EU, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE Directive): Products marked with this
UM DS-2CE71D0T-PIRL 072718NA
therefore with the applicable harmonized
symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more
Warnings
Follow
these
Cautions
Follow these
damage.
information see: www.recyclethis.info.
2006/66/EC (Battery Directive): This product contains a
battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the
product documentation for specific battery
information. The battery is marked with this
symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated
collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards
requirements.
Warning
This is a class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
Safety Instruction
These instructions are intended to ensure that user can
use the product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and
“Cautions.”
Warnings: Serious injury or death may occur if any of the
warnings are neglected.
Cautions: Injury or equipment damage may occur if any of
the cautions are neglected.
safeguards to prevent
serious injury or death.
precautions to prevent
potential injury or material
Warnings
•
In the use of the device, you must be in strict compliance
with the electrical safety regulations of the nation and
region.
•
Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 12 VDC
according to the IEC60950-1 standard. Refer to technical
specifications for detailed information.
•
Do not connect multiple devices to one power adapter to
avoid over-heating or a fire hazard caused by overload.
•
Make sure that the plug is firmly connected to the power
socket.
•
Make sure that the device is firmly fixed if wall mounting
or ceiling mounting is adopted.
•
If smoke, odor or noise rise from the device, turn off the
power at once and unplug the power cord, and then
contact the service center.
•
Never attempt to disassemble the camera by
unprofessional personal.
Cautions
•
Do not drop the camera or subject it to physical shock.
•
Do not touch senor modules with fingers.
•
Do not place the camera in extremely hot, cold (the
UM DS-2CE71D0T-PIRL 072718NA
operating temperature shall be -40° to 60° C), dusty or
Mark Description
D
C Voltage
damp locations, and do not expose it to high
electromagnetic radiation.
•
If cleaning is necessary, use a clean cloth with a bit of
ethanol, and wipe it gently.
•
Do not aim the camera at the sun or extra bright places.
•
The sensor may be burned out by a laser beam, so if any
laser equipment is in use, make sure that the surface of
the sensor is not exposed to the laser beam.
•
Do not expose the device to high electromagnetic
radiation or extremely hot, cold, dusty, or damp
environment.
•
To avoid heat accumulation, good ventilation is required
for the operating environment.
•
Keep the camera away from liquid while in use for nonwaterproof device.
•
While in delivery, the camera shall be packed in its
original packing or packing of the same texture.
Mark Description
1 Introduction
1.1 Product Features
The main features are as follows:
•
High performance CMOS sensor
•
IR cut filter with auto switch
•
OSD menu with configurable parameters
•
Auto white balance
•
Internal synchronization
•
SMART IR mode
•
Visible alarm
•
PIR detection
•
3-axis adjustment
1.2 Overview
Figure 1, Camera Overview
2 Installation
Before you start:
•
Make sure that the device in the package is in good
condition and all the assembly parts are included.
•
Make sure that all the related equipment is powered off
during the installation.
•
Check the specification of the products for the installation
environment.
•
Check that the power supply matches your required
UM DS-2CE71D0T-PIRL 072718NA
output to avoid damage.
•
Make sure the wall is strong enough to withstand three
times the weight of the camera, and the mount.
•
If the wall is concrete, insert expansion screws before
installing the camera. If the wall is wood, use self-tapping
screw to secure the camera.
•
If the product does not function properly, contact your
dealer or the nearest service center. Do NOT disassemble
the camera for repair or maintenance yourself.
2.1 Ceiling/Wall Mounting without Junction Box
1. Disassemble the camera.
1). Rotate the camera to align the notch to one of the
marks.
2). Pry the mounting base with a flat object (e.g., a
coin) to remove it from the camera body.
2. Paste the drill template (supplied) to where you want to
install the camera.
3. Drill the screw holes and the cable hole (optional) in the
ceiling/wall according to the drill template.
Figure 2, Drill Template
Note:
Drill the cable hole if using the ceiling outlet to route the
cable.
4. Attach the mounting base to the ceiling/wall, and
secure them with supplied screws.
Figure 3, Attach Mounting Base to Ceiling
Note:
The supplied screw package contains self-tapping screws
and expansion bolts.
For concrete wall/ceiling, expansion bolts are required to
fix the camera. For wood wall/ceiling, self-tapping screws
are required.
5. Route the cables through the cable hole or side
opening.
6. Align the camera with the mounting base, and secure
the camera on the mounting base.
UM DS-2CE71D0T-PIRL 072718NA
Figure 4, Secure Camera to Mounting Base
7. Connect the corresponding cables such as power cord
and video cable.
8. Power on the camera to check if the image on the
monitor is at an optimum angle. If not, adjust the
camera according to the figure below to get an
optimum angle.
Figure 5, 3-Axis Adjustment
1). Hold the camera body and rotate the enclosure to
adjust the pan position [0° to 360°].
2). Move the camera body up and down to adjust the
tilt position [0° to 75°].
3). Rotate the camera body to adjust the rotation
position [0° to 360°].
2.2 Mounting with Inclined Ceiling Mount
Before you start:
You need to purchase an inclined ceiling mount
separately.
1. Paste the drill template (supplied) where you want to
install the camera.
2. Drill screw holes and the cable hole on the ceiling/wall
according to the supplied drill template.
Figure 6, Drill Template
3. Disassemble the inclined ceiling mount with a
screwdriver.
4. Install the turret camera’s mounting base on the
inclined ceiling mount’s cover with three PM4 screws.
UM DS-2CE71D0T-PIRL 072718NA
Figure 7, Install Turret Camera’s Mounting Base
5. Install the inclined ceiling mount’s body on the
ceiling/wall with four PA4 × 25 screws.
Figure 8, Fix the Inclined Ceiling Mount’s Body
6. Combine the inclined ceiling mount’s cover with its
body with supplied screws.
7. Repeat steps 5 to 8 of Ceiling/Wall Mounting without
Junction Box to complete the installation.
Figure 9, Fix Camera to the Inclined Ceiling Mount
2.3 Ceiling/Wall Mounting with Junction Box
Before you start:
You need to purchase a junction box separately.
1. Paste the drill template on the ceiling/wall.
2. Drill screw holes and the cable hole (optional) in the
ceiling/wall according to the holes of the drill template.
Figure 10, Junction Box Drill Template
UM DS-2CE71D0T-PIRL 072718NA
Note:
Drill a cable hole if using the ceiling outlet to route the
cable.
3. Take apart the junction box, and align the screw holes
of the turret camera’s mounting base with those on the
junction box’s cover.
Figure 11, Install Turret Camera Mounting Base
4. Fix the mounting base on junction box’s cover with
supplied screws.
Figure 12, Install Junction Box on Ceiling/Wall
5. Secure the junction box’s body with supplied screws on
the ceiling/wall.
6. Combine the junction box’s cover with the junction
box’s body.
Figure 13, Fix the Camera to the Junction Box
7. Repeat steps 5 to 8 of Ceiling/Wall Mounting without
Junction Box to install the camera to the junction box.
2.4 Wall Mounting
Before you start:
You need to purchase a wall mount separately.
1. Drill four screw holes in the wall according to the holes
on the mount.
2. Install the mount to the wall by aligning the four screw
holes of the bracket with expansion screws on the wall.
3. Secure the mount with four hex nuts and washers.
UM DS-2CE71D0T-PIRL 072718NA
Figure 14, Install the Bracket
Figure 2-14 Install Mounting Base to Bracket
4. Install the mounting base of the turret camera to the
wall mount, and secure them with supplied screws.
5. Route the cables through the mount.
6. Repeat steps 6 to 8 of Ceiling/Wall Mounting without
Junction Box to complete the installation.
3 Menu Description
Purpose:
Call the menu by clicking the button on the PTZ Control
interface or call preset no.95.
1. Connect the camera to the TVI DVR and the monitor.
Figure 15, Connection
2. Power on the analog camera, TVI DVR, and the monitor
to view the image on the monitor.
3. Click PTZ Control to enter the PTZ Control interface.
4. Call the camera menu by clicking the button or call
preset no. 95.
UM DS-2CE71D0T-PIRL 072718NA
Figure 16, Main Menu Overview
5. Click the direction arrow to control the camera.
1). Click up/down direction button to select the item.
2). Click Iris + to confirm the selection.
3). Click left/right direction button to adjust the value
of the selected item.
3.1 VIDEO FORMAT
You can select the video format as 2 MP @ 25 fps or 2 MP
@ 30 fps.
3.2 LANGUAGE
Supports English and Chinese.
UM DS-2CE71D0T-PIRL 072718NA
3.3 EXPOSURE
EXPOSURE MODE
You can set the EXPOSURE MODE as GLOBAL, BLC, or
DWDR.
•
GLOBAL
Normal exposure mode, which adjusts lighting
distribution, variations, and non-standard processing.
•
BLC (Backlight Compensation)
Compensates light to the object in the front to make it
clear, but may cause overexposure of the background
where the light is strong.
•
DWDR (Digital Wide Dynamic Range)
Helps provide clear images even under backlight
circumstances. WDR balances the brightness level of
the whole image and provides clear images with details.
AGC (Auto Gain Control)
Optimizes image clarity in poor light conditions. The level
can be set as HIGH, MEDIUM, or LOW. Select OFF to
disable the AGC function.
Note:
The noise will be amplified when the AGC is on.
3.4 DAY/NIGHT
COLOR, B&W (Black White), and AUTO are selectable for
DAY/NIGHT switches.
Note:
Under LIGHTING mode, the image is in color all the time,
and there is no DAY/NIGHT settings in the menu.
•
COLOR
The image is colored in day mode all the time.
•
B/W
The image is black and white all the time, and it is best
to turn the IR LIGHT on in poor light conditions.
•
AUTO
You can turn on/off the IR LIGHT and set the SMART IR
value in this menu.
Figure 17, DAY/NIGHT
˗ IR LIGHT
You can turn on/off the infrared to meet the
requirements of different circumstances.
˗ SMART IR
The Smart IR function is used to adjust the light to its
most suitable intensity, and prevent the image from
over exposure. The SMART IR value can be adjusted
from 0 to 3. The greater the value is, the more
obvious effects are.
UM DS-2CE71D0T-PIRL 072718NA
˗ D-N THRESHOLD (Day to Night Threshold))
Controls the sensitivity of switching day mode to
night mode. You can set the value from 1 to 9. The
larger the value, the more sensitive the camera.
˗ N-D THRESHOLD (Night to Day Threshold)
Controls the sensitivity of switching night mode to
day mode. You can set the value from 1 to 9. The
larger the value, the more sensitive the camera.
3.5 VIDEO SETTINGS
Move the cursor to VIDEO SETTINGS and click Iris+ to
enter the submenu. CONTRAST, SHARPNESS, COLOR
GAIN, 3 DNR, and MIRROR are adjustable.
Figure 18, VIDEO SETTINGS
•
IMAGE MODE
Adjusts the image saturation. You can set it as STD
(Standard) or HIGH-SAT (High Saturation).
•
WHITE BALANCE
The white rendition function of the camera, adjusts the
color temperature according to the environment. It can
remove unrealistic color casts in the image. You can set
WB mode as AUTO or MANUAL.
˗ AUTO
White balance adjusts automatically according to the
color temperature of the scene illumination.
˗ MANUAL
You can set the R-GAIN/B-GAIN value from 1 to 255
to adjust the shades of red/blue color of the image.
Figure 19, MWB MODE
•
BRIGHTNESS
Brightness of the image. Set from 1 to 9 to darken or
brighten the image. The greater the value, the brighter
the image.
UM DS-2CE71D0T-PIRL 072718NA
•
CONTRAST
Enhances the difference in color and light between
parts of an image. Set the value from 1 to 9.
•
SHARPNESS
The amount of detail reproduced. Set value from 1 to 9.
•
SATURATION
Adjust to change the color saturation, from 1 to 9.
•
DNR (Digital Noise Reduction)
The DNR function can decrease noise, especially when
capturing moving images in poor light conditions, to
deliver more accurate and sharper images. You can set
the value from 1 to 9.
•
MIRROR
OFF, H, V, and HV are selectable for mirror.
OFF: The mirror function is disabled
H: The image flips 180° horizontally
V: The image flips 180° verticall
HV: The image flips 180° both horizontally and vertically
3.6 FUNCTIONS
WHITE LIGHT
The embedded white light source can work as a visible
alarm.
You can set WHITE LIGHT mode to ALARM or OFF.
When you set WHITE LIGHT to ALARM, you can set the
parameters in the TRIGGER MODE and the ALARM MODE
to meet your needs.
•
TRIGGER MODE
˗ DVR
Set TRIGGER MODE to DVR. In this way, the alarm
signal is sent from the DVR, and the camera works as
the alarm detector. Also, the alarm type supported
only by the DVR can also trigger the visible alarm in
the camera.
˗ CAMERA
Set TRIGGER MODE to CAMERA, the embedded PIR
module sends the alarm signal to the visible alarm in
the camera when the PIR module detects the alarm
source.
•
ALARM
You can set the ALARM MODE as SOLID or FLASHING.
Figure 20, ALARM MODE
˗ SOLID
In this mode, the white light source turns on when
the PIR module receives an alarm signal.
Set TIME SETTING as 5 s, 10 s, 15 s, 30 s, or 60 s, to
have the solid mode stay on for the set time when
the camera receives one alarm signal.
UM DS-2CE71D0T-PIRL 072718NA
Note:
The solid mode will stay for another set time when a
second alarm signal is received, and the rest can be done in
the same way.
˗ FLASHING
Set ALARM MODE to FLASHING to have the white
light source flash when the PIR module receives an
alarm signal.
˗ OFF
Select OFF to disable this function.
PIR LEVEL
Adjust the PIR module sensitivity. The greater the value,
the more sensitive the PIR module.
3.7 FACTORY DEFAULT
Reset all settings to the factory defaults.
3.8 EXIT
Move the cursor to EXIT and click Iris+ to exit the menu.
3.9 SAVE & EXIT
Move the cursor to SAVE & EXIT and click Iris+ to save the
settings and exit the menu.
UM DS-2CE71D0T-PIRL 072718NA
Loading...