Harbor Freight Tools 95736 Owner's Manual

Specifications

Overall Assembled
Rack Dimensions

Small Bin Dimensions (32) 6-1/2"L x 4-1/8"W x 3"H

Large Bin Dimensions (15) 9-1/4"L x 6"W x 5”H

Maximum Weight Capacity Overall Parts Rack: 171 Lb.

37"L x 11-1/4"W x 45-1/4"H

Large Bin: 5 Lb. each
Small Bin: 3 Lb. each

IMPORTANT SAFETY INFORMATION

Assembly Precautions

1. Assemble only according to these instructions.
Improper assembly can create hazards.

2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.

3. Keep assembly area clean and well lit.

4. Keep bystanders out of the area during assembly.

5. Do not assemble when tired or when under the
influence of alcohol, drugs or medication.

6. Weight capacity and other product capabilities apply
to properly and completely assembled product only.

7. Stay alert. Watch what you are
doing and use common sense during
assembly and use of this product.

8. During assembly dress properly. Do not wear
loose clothing or jewelry. Contain long hair.

9. Do not overreach. Keep proper
footing and balance at all times.

Page 2 For technical questions, please call 1-800-444-3353. Item 95736

Use Precautions

1. This product is not a toy. Do not allow
children to play with or near this item.

2. Use as intended only.

3. Inspect before every use; do not use
if parts are loose or damaged.

4. Do not exceed listed weight capacity.

5. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

6. Do not force the product. Use the correct product
for your application. The correct product will do
the job better and safer at the rate for which it is
designed. Do not force the product and do not
use it for a purpose for which it is not intended.

7. Locate the Parts Rack out of reach of children
and other untrained persons. The Parts Rack is
designed to hold small parts which can be easily
swallowed by small children. Keep children away.

8. Maintain this product with care.

9. Use only accessories that are recommended by
the manufacturer for your model. Accessories
that may be suitable for one product may become
hazardous when used on another product.

10. Use on a flat, level surface capable of
supporting the Parts Rack and its contents.

11. Load hardware evenly. As much as
possible, distribute the weight of all materials
stored in this Parts Rack evenly.

12. Do not use this Parts Rack as a stepping stool or
ladder. Never sit, stand, or climb on this Parts Rack.

13. Do not overload or over-stack this Parts Rack.
Overloading can damage bins and could possibly
result in tipping and personal injury. Over­stacking can result in tools or other objects
sliding or falling from the Parts Rack and could
result in damaged tools and/or personal injury.

SAVE THESE INSTRUCTIONS.

Page 3For technical questions, please call 1-800-444-3353.Item 95736

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following

pages, refer to Parts List and Assembly Diagram on page 6.

1. Attach ends of Hanging Bars (4) to left Column (2).
Secure with Bolts (5) and Nuts (8). Attach other ends
to right Column. Secure with Bolts (5) and Nuts (8).

(See Figure A.)

Column

(2)

Bolts

(5)

Figure A

2. Attach Hanging Bar Support (7) to center of Hanging
Bars. Secure with Bolts (6). (See Figure B.)

Hanging

Bar (4)

3. Secure one Column Support (3) to each Column
with Bolts (9) and Spring Washers (11).

4. Secure Columns to Bottom Plate (10) with
Bolts (9) and Spring Washers (11).

5. Secure Column Supports to Bottom Plate with Bolts
(9) and Spring Washers (11). (See Figure C.)

Column
Support

(3)

Bolt
(9) and
Spring

Washer

(11)

Figure C

6. Secure Top Cover (1) to Columns with
Bolts (9) and Spring Washers (11).

Bolt
(9) and
Spring

Washer

(11)

Column

(2)

Bottom

Plate

(10)

Hanging Bar

Support (7)

Bolt

(6)

7. Arrange Bins as desired. Slide Bin Lip over
Hanging Bar, making certain Bin is
securely in place. (See Figure D.)

Hanging

Bar

Bin
Lip

Figure B

.

Figure D

8. Set up the Parts Rack in desired location. Make
certain it is on a flat, even and stable surface
capable of supporting rated weight capacity.

9. Fill Bins as desired.

Page 4 For technical questions, please call 1-800-444-3353. Item 95736

Maintenance

Cleaning

1. Clean the Floor Rack with a damp cloth. Do not use abrasives, harsh chemicals
or detergents as these will scratch and damage the Bins and frame.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 5For technical questions, please call 1-800-444-3353.Item 95736

Parts List and Assembly Diagram

Parts List

Part Description Qty

1 Top Cover 1
2 Column 2
3 Column Support 2
4 Hanging Bar 7
5 Bolt (M4x8) 28
6 Bolt (M4x16) 7
7 Hanging Bar Support 1

Part Description Qty

8 Nut (M4) 28

9 Bolt (M4x14) 12
10 Bottom Plate 1
11 Spring Washer 12
12 Small Bin 32
13 Large Bin (not shown) 15

Record Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and

are not available individually as replacement parts.

Page 6 For technical questions, please call 1-800-444-3353. Item 95736

Assembly Diagram

11

1

9

7

6

5

8

2

9

4

11

12

10

9

11

11

9

9

11

3

Page 7For technical questions, please call 1-800-444-3353.Item 95736

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]