HANNA instruments HI 8010 User Manual

Instruction Manual

HI 8010

FUNCTIONAL DESCRIPTION

PRELIMINARY EXAMINATION

Remove the instrument from the packing material and examine it
carefully to make sure that no damage has occurred during ship­ment. If noticeable damage is found, notify your dealer.

HI 8010 comes supplied complete with HI 1230B pH electrode, cali­bration screwdriver, 1 x 9V battery and instructions.

Portable pH Meter

www.hannainst.com

WARRANTY

This meter is warranted for two years against defects in workmanship and materials
when used for their intended purpose and maintained according to instructions. Elec-
trodes are warranted for six months. This warranty is limited to repair or replacement
free of charge. Damage due to accidents, misuse, tampering or lack of prescribed main-

IST8010R1 05/05

tenance are not covered. If service is required, contact the dealer from whom you pur­chased the instrument. If under warranty, report the model number, date of purchase,
serial number and the nature of the problem. If the repair is not covered by the war­ranty, you will be notified of the charges incurred. If the instrument is to be returned to
Hanna Instruments, first obtain a Returned Goods Authorization Number from the Cus­tomer Service department and then send it with shipment costs prepaid. When shipping
any instrument, make sure it is properly packaged for complete protection.

Note: Save all packing material until you are sure that the instru-

ment functions correctly. Any defective items must be returned
in the original packing together with the supplied accessories.

SPECIFICA TIONS

Range 0.00 to 14.00 pH
Resolution 0.01 pH
Accuracy (@20°C/68°F) ±0.01 pH
Typical EMC Deviation ±0.05 pH
Calibration Manual, 2-point through trimmers
Temperature Manual, through trimmer

Compensation from 0 to 100°C (32 to 212°F)
Probe HI 1230B double junction, gel-filled,

pH electrode with BNC connector and 1 m cable (included)
Environment 0 to 50°C (32 to 122°F); RH max 95%
Power Supply 1 x 9V battery

approx. 100 hours of continuous use

Dimensions 185x82x53 mm (7.3x3.2x2.1’’)
Weight 265 g (9.3 oz.)

HI 8010 is in compliance with the directives.

OPERA TIONAL GUIDE

• Slide off the battery compartment cover on the back of the meter
and install the supplied 9V battery, while paying attention to its
polarity.

• Connect the pH electrode to the BNC socket on the top of the
meter and remove the electrode protective cap.

• Immerse the electrode (at least 4 cm/1.5’’) and an accurate
thermometer (eg. ChecktempC) in the sample to be tested, as
close as possible one to the other.

• Turn the rotary knob to the °C position to display the temperature
setting. With the provided screwdriver, adjust the °C trimmer to
read on the LCD the temperature measured by the thermometer.

• Turn the rotary knob to the pH position, shake the electrode
briefly and allow the reading to stabilize. The display will show the
pH value compensated for the manually adjusted temperature.

• After measurements, switch the meter OFF by turning the rotary
knob to the OFF position, disconnect the electrode from the meter
and store it with a few drops of HI 70300 solution in the protective
cap.

Notes:

• Before taking measurements, make sure the meter is calibrated.

• If the electrode has been left dry, soak the tip in HI 70300 storage
solution for at least one hour to reactivate it.

• For a faster response time when
using refillable electrodes,
unscrew the refill hole cap.

• If measurements are taken in different samples successively, it is
recommended to clean the electrode thoroughly to eliminate cross­contamination. After cleaning, rinse the electrode with some of the
sample to be measured.

CALIBRA TION PROCEDURE

For better accuracy , a frequent calibration of the meter is recommended.
Moreover, the instrument should be calibrated:

a) when the pH electrode or the battery is replaced;
b) at least once a month;
c) after testing aggressive chemicals;
d) where extreme accuracy is required.

Preparation

• Pour small quantities of pH 7.01 (HI 7007) and pH 4.01 (HI 7004)
solutions into two clean beakers.

• For accurate calibration use two beakers for each solution: the
first one for rinsing the electrode, the second one for calibration.

• For accurate readings, use pH 7.01 (HI 7007) and pH 4.01
(HI 7004) if samples to be measured are acidic, or pH 7.01
(HI 7007) and pH 10.01 (HI 7010) for alkaline measurements.

• If calibration to NBS standards is required, use pH 6.86 (HI 7006)
instead of pH 7.01 and pH 9.18 (HI 7009) instead of pH 10.01.

Procedure

• Remove the protective cap from the electrode, rinse and immerse
it in pH 7.01 buffer and stir gently. Wait a couple of minutes for the
reading to stabilize.

• Measure the solution temperature with a ChecktempC, e.g. 20°C.

• Set the rotary knob to the °C position to display the manual
temperature setting and adjust the °C trimmer until the LCD shows
the measured temperature.

• Set the rotary knob to the pH position, wait for the reading to
stabilize and with a small screwdriver adjust the pH7 trimmer until
the LCD shows the pH value at the above temperature (see pH
vs. temperature chart on the buffer bottle).

• Rinse and immerse pH electrode and thermometer in pH 4.01 or
pH 10.01 buffer (2nd calibration point); stir gently.

• Wait a couple of minutes, then adjust the pH4/10 trimmer until the
LCD shows the pH value at the noted temperature (see pH vs.
temperature chart on the buffer bottle).

The calibration is now complete and the meter is ready for use.

BA TTERY REPLACEMENT

When the battery becomes weak, the instrument automatically switches
the display off. It is recommended to replace the battery immediately.
Replacement must only take place in a non-hazardous area using an
alkaline 9V battery. Remove the battery cover and replace the old
battery with a new one, while paying attention to its polarity.

Note: After changing the battery, recalibrate the meter.

ACCESSORIES

ChecktempC Electronic thermometer (range: -50 to 150°C)
HI 1230B Plastic-body, double junction, gel-filled, combination pH

electrode with BNC connector and 1 m cable

HI 1332B Plastic-body, double junction, refillable, combination pH

electrode with BNC connector and 1 m cable

HI 70030M Electrode storage solution, 230 ml bottle
HI 7004M pH 4.01 buffer solution, 230 ml bottle
HI 7006M pH 6.86 buffer solution, 230 ml bottle
HI 7007M pH 7.01 buffer solution, 230 ml bottle
HI 7009M pH 9.18 buffer solution, 230 ml bottle
HI 7010M pH 10.01 buffer solution, 230 ml bottle
HI 7061M General cleaning solution, 230 ml bottle
HI 7082 Refilling electrolyte solution for double junction electrodes,

3.5M KCl, 30 ml bottle, 4 pcs