Hanna Instruments HI 149-01 Instruction Manual
Instruction Manual
HI 149-00 • HI 149-01
Remote Probe Thermometer
www.hannainst.com
Foodcare
ACCESSORIES
PROBE EPW: probe with
sharp tip for penetration
PROBE ELW: probe for general use and liquids
PROBE ECW: probe for air
and gas
PROBE EMW: surface
probe
90mm
3.5"
195mm
7.7"
90mm
3.5"
235mm
9.3"
90mm
3.5"
240mm
9.4"
90mm
3.5"
270mm
10.6"
SUGGESTIONS FOR USERS
Before using this product, make sure that it is entirely suitable for the environment in which it is
used. Operation of this instrument in residential area could cause unacceptable interferences to
radio and TV equipments, requiring the operator to take all necessary steps to correct interferences.
Any variation introduced by the user to the supplied equipment may degrade the instrument's EMC
performance. To avoid electrical shock, do not use this instrument when voltages at the measurement
surface exceed 24 Vac or 60 Vdc. To avoid damages or burns, do not perform any measurement in
microwave ovens.
WARRANTY
These meters are warranted for two years against defects in workmanship and materials when
used for their intended purpose and maintained according to instructions. The probes are warranted for a period of six months. This warranty is limited to repair or replacement free of
charge. Damages due to accident, misuse, tampering or lack of prescribed maintenance are not
covered. If service is required, contact the dealer from whom you purchased the instrument. If
under warranty, report the model number, date of purchase, serial number and the nature of the
failure. If the repair is not covered by the warranty, you will be notified of the charges incurred. If
the instrument is to be returned to Hanna Instruments, first obtain a Returned Goods Authorization Number from the Customer Service department and then send it with shipment costs prepaid.
When shipping any instrument, make sure it is properly packaged for complete protection.
IST149R2 06/05
HI 149 is a portable K-type thermocouple thermometer for
routine checks in the food industry.
Thanks to the user-replaceable probe, HI 149 can be
used in a wide range of applications.
You have a choice of four probes, specifically manufactured to measure the temperature of liquids, air, surface,
solids and semi-solids.
Two models are available for measurement in degrees
Celsius (HI 149-00) and Fahrenheit (HI 149-01).
OPERATION
• Connect one of the four probes (see
accessories) by opening the rear
cover and inserting the 3-pin connector.
• To switch the HI 149 on, open the
front cover as indicated in the picture, and slide the ON/OFF switch
to the “ON” position.
• The temperature will be displayed
in either °C or °F, depending on
model.
SLIDE
DOWN
°c
ON
OFF
°c
Foodcare
020
Foodcare
BATTERY REPLACEMENT
When the HI149 can not be
switched on or the display fades,
pull out the rear cover, remove
the battery cover and replace all
three batteries, while paying attention to their polarity.
Batteries should only be replaced in a safe area and
using the battery type specified in this instruction manual.
REAR
COVER
PULL
FROM
TOP
BATTERIES
BATTERY
HOUSING
BATTERY
COVER
REAR
COVER
SPECIFICATIONS
HI 149-00 (°C) HI 149-01 (°F)
Range -40 to 300°C -40 to 572°F
Resolution 1°C 1°F
Accuracy ±2°C ±4°F
Typical EMC Dev. ±2°C ±4°F
Probe Interchangeable, stainless steel,
with 1 m (3.3’) cable
Battery Type 3 x 1.5V
Battery Life Approx. 700 hours of continuous use
Environment 0 to 50°C (32 to 122°F); RH max 95%
Dimensions 106 x 68 x 21 mm (4.2x2.7x0.8”)
Weight 80 g (2.8 oz.)
BACK
POCKET
CLIP
TEMPERATURE
PROBE
HOLDERS
TEMPERATURE
PROBE
CABLE
REAR
COVER
FRONT
COVER
FRONT
LIQUID
CRYSTAL
DISPLAY
°c
020
Foodcare
REAR
COVER
REAR
COVER
PULL
FROM
TOP
3-PIN
PROBE
CONNECTOR
• To change the probe, open the rear cover of the unit
and release the probe connector prior to inserting the
new probe.
• When not in use, switch the HI 149 off.
• Variations in readings or fading display can indicate
weak batteries.
Loading...