Haier HL37E, HL52E, HL42E, HL47E User Manual

TFT-LCD TV
OWNER S MANUAL'
Please READ this manual carefully before operating your TV, and retain it for future reference.
MODELS:
HL37E HL42E HL47E HL52E
WARNING
RISK ELECTRIC SHOCK DO NOT OPEN
WARNING : To reduce the risk of electric shock do not remove cover or back. No user-serviceable parts inside refer service to qualified service personnel.
Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of th product. Read the following safety instruction before starting the operation.
The User Manual uses the following symbols to ensure a safe operation and prevent any damage to operators or properties:
THIS SYMBOL INDICATES THAT HIGH VOLTAGE IS PRESENT INSIDE. IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT WITH ANY INSIDE PART OF THIS PRODUCT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, use and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However ,there is no guarantee that interference with not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures: *Reorient or relocate the receiving antenna. *Increase the separation between the equipment and receiver. *Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. *Consult the dealer or an experienced radio/TV technician for help. This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may be not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION: To assure continued compliance and possible undesirable interference, the provided ferrite cores must be used when connecting this plasma display to video equipment; and maintain at least 40cm spacing to other peripheral device.
CANADIAN NOTICE: This Class B digital apparatus compiles with Canadian ICES-003.
IMPORTANT SAFETY INSTRUCTIONS
Read all of the instructions before using this appliance. When using this
appliance, always exercise basic safety precautions, including the following:
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer`s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15) WARNING-To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
PORTABLE CART WARNING
(symbol provided by RETAC)
S3126A
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
The mains plug is used as the disconnect device, remain it readily operable during the apparatus normal use.
Owner s Manual 3
SAVE THESE INSTRUCTIONS
Thank you for using our Haier product. This easy-to-use manual will guide you in getting the best use of your product. Remember to record the model and serial number. They are on label in back of the unit.
Model number
serial number
Date of purchase
Staple your receipt to your manual. You will need it to obtain warranty service.
4 TV LCD-TFT
Contents
Introduction
War nin g . . . . . . . ...... ... ... .. . . . . . . . . . . . . . . . . . . . . . . .
Saf ety I nst ruc tio ns . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Introduction
Con tro ls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ... ... ... ..
Connection Options . . . . . . . . . . . . . . . . . . . . . .............
Universal Remote Controller . ............ . . . . . . . . ......
Installation
Acc ess ori es . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... ...... ..
Antenna Connection . . . . . . . . . . ..............................
VCR Connection. . . . . . . . . . . . . . . . . . . . . ............... ..
External A/V Source Setup . . . . .. . . . . ......................
DVD Connection . . . . . ...... . . . . . . . . . . . . . ................
DTV Connection.....................................................
Digital Audio Output . . . . . . . . . . . . . . . . . . . . ..............
PC Connection. . . . . . . . . . . . . . . . . . . . . . . ................
Monitor Out Setup . . . . . . . . . . . . . . . . . . . . ............... .
HDM I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..... ... ... ... ... .
Cable Sample.........................................................
Connecting Headphones . . . . . . . . . . . . . . . . . . . ....... .
Pow er so urc e.. ... ...... ... .. . . . . . . . . . . . . . . . . . . . . . . . . .
Operation
Switching On/Off the TV set . . . . . ... . . . . . . . . . . . ... ...
Choose the Menu Language . . . . ..... .......................
Choose the input Source.........................................
Channel Menu
Automatic Scan. . . . . . . . . . . . . ............................. . .
Man ual S can . . . . ... ... ...... .. . . . . . . . . . . . . . . . . . . . . .. .
Fine Tune................................................................
Edi t Pro gra m.. ... ...... ... . . . . . . . . . . . . . . . . . . . . . . . . . ..
Rename .............. . . . . . . . . . . . . . . . . . . . . . . . . ..........
elect the desired program
S . . . . . ........... ............ . . ..
elect the desired sound
S . . .............. . . . ............ . . ..
Mute .............. . . . ............................................ . . ..
Video Menu
How to select picture modes.....................................
How to customize your own picture status .................
Asp ect R ati o Con tro l . . . . . . . . . . . . . . . . . . . . ... . .. . . ..
Audio Menu
How to select audio modes......................................
How to customize your own audio status ..................
SAP Broadcasts Setup............................................
Time Menu
Date /Time setting...................................................
Timer on setting......................................................
Timer off setting......................................................
Sleep Timer setting.................................................
Time zone setting...................................................
Daylight Saving setting...........................................
Function Menu
Closed Captions.....................................................
CC mode...............................................................
NTSC Caption
DTV Caption..........................................................
DTV Caption Style..................................................
OSD Timeout Blue screen OSD transparency
Adjust
Menu
Screen Setup for PC mode......................................
Lock Menu
Parental Control rating and categories......................
Others Functions
Bri ef In fo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ... ... .. . .
Quick program view................................................
Setting up your remote control ................................
USB system .......................................................
Maintenance . . ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Specifications . . . . . . . . . . . . . . . . . . . . . . .. .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .
Warranty . . . . ... ...... ... . . . . . . . . . . . . . . . . . . . .. . . . . . .
........................................................
.........................................................
...........................................................
..................................................
Owner s Manual 5
Controls
-This is a simplified representation of front panel.
-Here shown may be somewhat different from your TV.
Front panel controls
Introduction
POWER
-
CH
1.CH-/+ Program minus and plus, menu options
2.VOL-/+ Volume increase and decrease, menu reset and entry
3.INPUT: all input resouce display and OK confirm:
4..MENU Menu display
5.POWER:Is used to activate the display or return to standby mode
CH+
VOL - VOL+
INPUT
MENU
6 TV LCD-TFT
Connection Options
Left side connetions
Antenna Input
Connect cable or antenna signals to the TV, either directly or through your cable box.
PC VIDEO Input
Connect the monitor output connector from a PC to the jack
S-Video Input
Connect S-Video out from an S-VIDEO device to the S-VIDEO input.
A N T I
N
H D M I2
P C
1
2
Y
C
P
O
b
M P
P
O
r
N E N
L
T
R
S
­V
ID E
O
V I
D E O 1
L
R
HDMI2 connect a signal to HDMI/DVI.
DVD/DTV Input
(Component )
Connect a component video device to these jacks.
VIDEO Input
Connects the
video signal from a video
device.
HDMI1 connect a signal to HDMI/DVI.
DVI/PC Audio Input
Connect the audio out from the external device, used while using a DVI to HDMI connector.
Power Cord Socket
This TV operates on AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power
H D M I1
Earphone jack:
A
P
U
C
D
/D
IO
V
I I N
O P T I
C A L
A C IN
Earphone audio output terminal.
Power Cord Socket
This TV operates on AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power
Remote Controller
- The remote controller cannot be operated unless the batteries are properly loaded.
- When using the remote control, aim it at the remote control sensor on the TV.
Introduction
Function introduction
POWER
Turns your TV or any other programmed
equipment on or off, depending on mode.
TV USB
Press the SELECT button repeatedly to select one of the system modes in which the remote control can be used.
When the desired device is selected, the corresponding LED lights on 5seconds.
FAVORITE
Open the favorite channel list.
AUDIO.LIST
Open the channel list.
CH.LIST
USB
Press to enter USB signal
TV
Press to enter TV signal
CCHH LL II SS TT FF
CC HH LL II SS TT FF
TVTVTV
TVTVTV
EEEDDDOOOMMMVVVTTT EEEDDD
EEEDDDOOOMMMVVVTTT EEEDDD
AAVV.. LL SSTTII
AAVV..LL SSTTII
AAUU DDII OO
AAUU DDIIOO
MMM
MMM
ZOOM
ZOOMZOOM
ZOOM
ZOOMZOOM
OOO
OOO
II SS TTLL
II SS TTLL
HOTKEY
HOTKEY
RETURN
RETURN
Open the audio channellist.
ZOOM( only SUB System)
To enlarge or lessen the picture
HOTKEY
.
Call up the menu
/ Rewind / Fast / backward /Forward
Play
II Pause
( only SUB System)
RETURN
Selects the picture appropriate
for the program`s character.
E
E
M
M
TI
TI
E
E
M
M
TI
TI
CC(closed caption)
P.MODE
Select a closed caption:
CC MUTE, CC ON, CC OFF.
TIME
Shows time.
MENU
Brings up the main menu to the screen.
EXIT
Clears all on-screen displays and
returns toTV viewing from any menu.
Switches the sound on or off
MUTE
ARC
(Aspect Ratio Control)
Changes the aspect ratio.
S.MODE
Selects the sound appropriate for the program's character.
FREEZE
Freezes the currently-viewed picture, but audio continues. Press FREEZE button again to resume the normal picture.
INPUT
show the input source mode.
INFO
When you watch the TV, press the key, the information displays on bottom of the screen.
THUMBSTICK (Up/Down/Left/Right/OK)
Allows you to navigate the on-screen menus and adjust the system settings to your preference.
SLEEP button
Displays the Sleep Timer option.
LIGHT
Press the light button, white LED will be ON, release this key, white LED will be OFF.
SAP
Selects MTS sound: Mono, Stereo, and SAP in Analog mode. Change the audio language in DTV mode.
Increases/decreases the sound level.
Numeric buttons
VOLUME UP/DOWN
press to change the channel.
- button
Press to select additional channels
being broadcast by the same station.
“54-3”, press “54”, then press “-” and “3”.
Note: For DVD function see page 35.
For example, to select channel
(digital and analog)
CHANNEL UP/DOWN
Selects available channels
Q.VIEW
Switch the current channel to the last channel you have viewed.
External Equipment Connections
Accessories
EEEDDDOOOMMMVVVTTT EEEDDD
OOO
MMM
AAVV..LLSSTTII
CCHHLLIISST T FF
AAUUDDIIOO
IISSTTLL
TVTVTV ZOOM
ZOOMZOOM
HOTKEY
RETURN
E
M I T
E M I
T
OWNER S MANUAL'
TFT-LCD TV
Please READ this manual carefully before operating your TV, and retain it for future reference.
Installation
Remote controller
Owner`s manual
Alkaline battery(AAA) 2
Power cable
Antenna Connection
Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an outdoor antenna .In different places, the suitable antenna type and position are different.
Multi-family Dwellings/Apartments (Connect to wall antenna socket)
Wall Antenna Socket
Bronze Wire
RF Coaxial Wire (75 ohm)
VHF Antenna UHF Antenna
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Outdoor Antenna
Turn clockwise to tighten.
Bronze Wire
Be careful not to bend the bronze wire when connecting the antenna.
To improve the picture quality in a poor signal area,
please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV`s, install a 2-
Way Signal Splitter in the connections.
If the antenna is not installed properly, contact your dealer
for assistance.
Owner s Manual 9
External Equipment Connections
NOTE: All cables shown are not included with the TV.
Choose Your Connection
There are several ways to connect your television, depending on the components you want to connect and the quality of the signal you want to achieve. The following are examples of some ways to connect your TV. Choose the connection which is best for you.
VCR connection
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV
Connection Option 1
Set VCR output switch to channel 3 or 4 and then tune the TV to the same channel number.
Installation
Connection Option 2
1. Connect the audio and video cables from the
VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner`s manual.)
3. Select the input source with using the
INPUT button on the remote control, and then press / button to select the source, press the OK button to confirm.
ANT IN
Y2
Pr2Pb2
Y1
L R L R
Pr1Pb1
S-VIDEO
AV OU T L R
VIDEO L R
10 TV LCD-TFT
External Equipment Connections
External A/V Source Setup
How to connect
Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).
How to use
1. Select the input source with using the INPUT button on the remote control.
2. Press the / button to select the desired source.
3. Press the ok button to confirm
4. Operate the corresponding external equipment.
Y2 Y1
Pr2Pb2 Pr1Pb1
Installation
R
L L
R
S-VIDEO
AV OU T L R
VIDEO L R
Camcorder
DVD connection
How to connect
1. Connect the DVD video outputs (Y, Pb/Cb, Pr/Cr) to the Y, Pb, Pr jacks on the TV and connect the DVD audio outputs to the YPbPr Audio IN jacks on the TV, as shown in the figure.
2. If your DVD only has an S-VIDEO output jack, connect this to the S-VIDEO input on the TV. as shown in the figure.
NOTE: If your DVD player does not have component video
output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the INPUT button on the remote control to select YPbPr mode.
3. Press Play button on external equipment for program play.
4. Refer to the DVD player's manual for operating instructions.
Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Y Pb Pr
Video Game Set
Y2
Pr2Pb2
Y1
Pr1Pb1
R
L L
R
S-VIDEO
AV OU T L R
VIDEO L R
Video output ports on DVD player
Y Pb Pr Y B-Y R-Y
Y Cb Cr Y P P
BR
Owner s Manual 11
Installation
External Equipment Connections
DTV connection
- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).
How to connect
Use the TV`s (Y, PB, PR) , PC or HDMI jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the owner`s manual for the digital set-top box.)
2. Use INPUT on the remote control to select YPbPr, PC,or HDMI source.
Y2
Pr2Pb2
PC
Y1
L R L R
Pr1Pb1
S-VIDEO
AV OU T L R
VIDEO L R
HDMI1
PC/DVI AUDIO IN
OPTICAL
Signal
480i
480p
720p
1080i
YPbPr
Yes
Yes
Yes
Yes
HDMI/DVI
Yes
Yes
Yes
Yes
Audio Output
Send the TV`s audio to external audio equipment (stereo system) via the Audio Output (Optical) port.
How to connect
1. Connect one end of an optical cable to the TV Audio (Optical) Output port.
2. Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment. See the external audio equipment instruction manual for operation.
Digital Set-top Box
PC/DVI
OPTICAL
AUDIO IN
AC IN
Note: When connecting with external audio equipments, such as amplifers or speakers, please turn the TV speakers off.
Caution: Do not look into the optical output port. Looking at the laser beam may damage your vision.
12 TV LCD-TFT
Installation
External Equipment Connections
PC connection
How to connect
1. To get the best picture quality, adjust the PC graphics card to 1024
2. Use the TV`s PC or DVI (Digital Visual Interface)Audio IN port for video connections, depending on your PC connector.
If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of eitherPC r DVI IN to
display the PC on the TV.
If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to eithe DVI; (the other mode is
set to Plug and Play automatically by the TV.)
3. Then, make the corresponding audio connection. If using a sound card, adjust the PC sound as required.
How to use
1. Turn on the PC and the TV.
2. Turn on the display by pressing the POWER button on the TV's remote control.
3. Use INPUT on the remote control to select PC or HDMI source.
4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC
mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
NOTES: 1 Use a DVI cable. 2 Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the
screen. 3 The synchronization input form for Horizontal and Vertical frequencies is separate.
x768 .
IN o
r PC or
Resolution
Mode
PC
SPC
XGA
Resolution
Frame frequency (Hz)
640*480 60Hz
800*600 60Hz/75Hz
60Hz
1024*768
75Hz
ANT IN
HDMI2
PC/DVI
PC
HDMI1
AUDIO IN
OPTICAL
Owner s Manual 13
External Equipment Connections
Monitor Out Setup
The TV has a special signal output capability which allows you to hook up a second TV or monitor.
Connect the second TV or monitor to the TV`s AV OUT. See the Operating Manual of the second TV or monitor for further details regarding that device`s input settings.
Notes:
YPbPr, PC, HDMI,DTV input sources cannot be used for Monitor out.
When connecting with external audio equipments, such as amplifers or speakers, please turn the TV speakers off.
Installation
Y2
Pr2Pb2
Y1
L R L R
Pr1Pb1
S-VIDEO
AV OU T L R
VIDEO L R
HDMI
<When the source device(DVD player or Set Top Box) supports HDMI>
How To Connect
1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product).
2. No separated audio connection is necessary.
How To Use
- If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p.
- If the source device does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
- Select HDMI input source in input source option of Select Main source menu.
<When the source device(DVD player or Set Top Box) supports DVI>
How To Connect
1. Connect the source device to HDMI port of this TV with a HDMI-to-DVI cable(not supplied with this product).
2. A separated audio connection is necessary.
3. If the source device has an analog audio output connector, connect the source device audio output to DVI Audio In port located on the left side of HDMI port.
How To Use
- If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p.
- If the source device does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
- Press the INPUT button to select HDMI input source in input source option of Select Main source menu.
14 TV LCD-TFT
Cable sample
Installation
HDMI Cable (not supplied with the product)
HDMI to DVI Cable (not supplied with the product)
Analog Audio Cable (Stereo to RCA type) (not supplied with the product)
Owner s Manual 15
Loading...
+ 35 hidden pages