Haier HHN1230DBBB, HHN1230DBWW, HHV2230DBBB, HHV2230DBWW, HHV2230SBSS User Manual

User Manual Model

1000/2000 Series

Guide de l’Utilisateur

1000/2000 Series

Manual del Usuario Modelo

1000/2000 Series

Range Hood

Extractor de Aire

Hotte de Cuisinière

English

1

SAFETY PRECAUTIONS

WARNING!
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have
questions, contact our customer service department for assistance.
Our Toll-Free number is 1-877-337-3639.

2. Before servicing or cleaning unit, switch power off at service panel and

lock the service disconnection means to prevent power from being switched
on accidentally. When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag, to the service
panel.

3. Installation work and electrical wiring must be done by a qualified person(s)

in accordance with all applicable codes and standards, including fire-rated
construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases

through the flue (chimney) of fuel burning equipment to prevent backdrafting.
Follow the heating equipment manufacturer’s guideline and safety standards
such as those published by the National Fire Protection Association (NFPA),
and the American Society of Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring

and other hidden utilities.

6. To reduce the risk of fire or electric shock, do not use this range hood with an

additional speed control device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings. Boilovers cause smoking
and greasy spillovers that may ignite. Heat oils slowly on low or medium
settings.

2. Always turn hood ON when cooking at high heat or when cooking flaming

foods.

3. Clean ventilating fans frequently. Grease should not be allowed to accumulate

on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the size of the

surface element.

English

2

Thank you for using our Haier product.
This easy-to-use manual will guide you
in getting the best performance from
your Haier Range Hood.

Remember to record the model and
serial number. They are on a label in
the range hood.

Model number

Serial number

Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then
turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not
go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN — You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam

explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already know how

to operate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

*Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION!

Important – Observe all governing codes and ordinances.

1. For general ventilation use only. Do not use this appliance to exhaust
hazardous or explosive materials and vapors.

2. To reduce the risk of fire, use only metal ductwork.

3. To avoid damage to motor or other components, keep drywall spray,
construction dust, etc. off the power unit.

4. Please read specification label on product for further information and
requirements.

SAVE THESE INSTRUCTIONS

for Future Use

English

3

Accessories

Range Hood Accessories Provided:

1 Range Hood

1 7” Round Duct Plate*

1 Damper/Duct Connector*

4 Damper Screws*

4 Washers

4 Range Hood Wood Screws

2 Wire Connectors

1 Charcoal Filter (not included with 1000 series models)

1 Aluminum Filter

1 User Manual

* Included with 2000 series models that allow for ducted installations.

Not included with 1000 series.

Check to make sure that all parts and accessories are present and in good

contact our customer service department for assistance.

Our Toll-Free number is 1-877-337-3639.

Table Of Contents

PAGE

Safety Precautions....................................................................................1-2

Accessories ...............................................................................................3

Installation Preparation ...............................................................................4

Preparing Hood Location ............................................................................4

Preparing Hood...................................................................................... 5-7

Preparing Electrical Connections..................................................................8

Installing Hood .......................................................................................... 9

Operating the Range Hood....................................................................10-11

Use and Care..........................................................................................12

Troubleshooting .......................................................................................13

Warranty Information ...............................................................................14

English

4

Installation Preparation

To install this range hood, you will need the following tools and materials:

Note: This procedure will require 2 people for easier installation.

Tools Needed for Installation

t Drill
t 1/8” Drill bit for drilling pilot holes
t 1-1/4” Wood bit for drilling electrical wiring access hole
t Phillips head screwdriver
t Flat-head screwdriver
t Pliers
t Pencil, ruler and level for marking range hood location
t Hand saw or jig saw for cutting the wall or cabinet openings
t Hi-Temp duct tape
t Electrical tape
t Connector Clamp
t Electrical Conduit

Preparing Hood Location

1. If you have a 2000 series model, you must determine whether hood will
discharge vertically (3¼” x 10” or 7” Round), horizontally (3¼” x 10” only) or
non-ducted. For vertical or horizontal discharge, run ductwork between the hood
location and a roof cap or wall cap. For best results, use a minimum number of
transitions and elbows. 1000 series models can only be installed as non-ducted.

2. Use diagram, below, for proper placement of ductwork and electrical cutout in
cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole.