Haier DWE-290-TG User Manual

User's manual

XPB90-99GS

Twin-tub Washing Machine

Please read this manual carefully before using.

Retain it for reference
please check if the power receptacle is earthed

reliably before usage to guarantee your safety

The manufacturer is not responsible for any
risks occurred owing to disobey these
stipulations.

Contents

Before using

Names of the parts.............the 2nd cover

Safety precautions ...............................1

Installation and adjustment ..................3

Introduction of the major functions .......5

Using process

Preparation before washing ................6

The musts in washing .........................7

Usage of the detergent .......................8

Washing sequence ..............................9

Disposal after washing .......................13

Trouble-shooting*

Answers to question.....................15

Packing list ......................................16

Specification*

Circuit diagram...........the back cover

Before Using

Names of the parts

Before Using

Honourable users,
Thank you for choosing our products.
Our products integrate high-tech, precision, frontier science .To facilitate using it, please read this manual
carefully and operate this machine according to it.

Water-filling entrance

Water inlet selector handle

Buzzer

Wash selector

Wash timer

Control panel

Cascade outlet

filter frame

Lint filter

Inner tube

Pulsator

Drain hose

Base frame

Outer cover of the spin tub

Inner cover of the spin tub

Spin timer

Spin tub frame

Spin tub

Cabinet

Power cord

Accessories

Water inlet hose
(one piece)

Gland
(one piece)

Meaning and description of the symbols

Contents marked with that symbol

Warning sign

Forbidding sign

are related to the safety of the
product and the personal safety
of the users. Please operate in
strict conformity to the contents,
otherwise it may cause damage
of the machine or injure the
personal safety of the user.

Contents marked with that symbol
are actions forbidden to perform.
Performing of those actions may
result in damage of the machine
or injure the personal safety of
the user.

Safety precautions

Before Using

Before Using

Be sure to use three-phase receptacle.
Earth the earthing terminal of the
receptacle reliably.

Earth

If the power cord is bad, to avoid risk it is required to replace it by the technicians
of our special shop or the after-sale service department. Keep the pin of the power
plug clean.

In case the washing machine is installed
on ground with carpet , do not block the
ventilation hole with carpet.

Be sure to pull the plug off when there's
power failure, or the machine is being
moved, cleaned or when it is idle.

Do not use water hotter than 50 C .

Ventilation hole at
the bottom of the
washing machine

Do not put the machine at damp place
like the bathroom . Never wash it with
water.

Do not share one receptacle with other
electric appliances. Do not use it in
case that the power plug is damaged
or the inserting into the receptacle is
loose.

Do not wash water-proof laundries such
as the raincoat, bicycle shelter etc. To
avoid abnormal vibration during spinning.

Safety precautions

Before Using

Before Using

Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.

Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.

Do not decompose, repair or alter the
machine by yourself.

Do not wash laundries with volatile
materials (such as thinner, petrol etc.).

l

Petro

Thinner

Handicapped or children without care
shall not use the machine.

To prevent your laundries and washing
machine from damage , be sure to take
out of the foreign materials from your
pocket , such as coins, buttons, sand
or hair pins etc.

Keep the machine away from direct
sunlight and heat source like the
heater.

Before washing, please check if the
water tap is open, and if the water inlet
pipe is connected properly.

It is suggested to use low-foaming
washing powder

Before Using

Installation and adjustment

Before Using

Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.

Usage of the drain hose

The drainage shall be smooth with the drain hose.

1.The height of the drain hose shall
be less than 10cm. or the drainage
will not be smooth enough and cause
incomplete drainage.

3.If the drain hose is too long, cut
it at mid point. To make smooth
drainage, cut the front end of
the hose slantingly.

2.Do not step on or press the drain hose.

4.IF extra drain hose is needed,
please make separate purchase.
The inner diameter of the extra
hose shall be not less than
30mm, and the length shall
be not exceed 1.5m.

Install the water inlet hose; Select the water level

Insert the water inlet hose into the water-filling
entrance on the control panel directly. (pull it
out to dismantle it)

Select water level according to the
quantity of the laundries.

Attention:
In water filling, do not exceed
the"Max" water level. Otherwise
the water may overflow out of the
washing machine.

Water inlet hose

Water level
adjusting lever

Maximum

(about 83L)

Medium

(about 68L)

Minimum

(about 49L)

Max

Med

Min

Water-filling
entrance

How to change the direction of the drain hose

Figure 1 indicates the ex factory installation
position of the drain hose.

Soft item

Extend the drain hose from the side of spin tub

Put soft items on the ground. Lean the machine
down gently with the front surface facing the
ground. Take off the drain hose from the cabinet.
Dismantle the drain hose fixing clamp and take
the hose out of the fixing groove.
(See to Figure 2).

Drain hose fixing clamp

Before Using

Before Using

Back

Front

Figure 1

Soft item

Embed the drain hose into the groove along the side
of the spin tub in the order of (1)~(3), heading for the
side of the spin tub. (See to Figure 3).

Extend to the
spin tub side

Embed the drain hose into the groove with
hands. Take care not to damage the drain
hose in fastening the fixing clamp.

Extend the drain hose from the rear side

Dismantle the drain hose fixing clamp.
Take out the drain hose from the fixing groove.
Extend it from the rear side as per the direction
of the arrow. (When the drain hose is extended
from the rear side, it can be hung on the point
for drain hose at the two sides of the cabinet.)
(See to Figure 4).

Figure 2

Embed into the
groove in turn

Figure 3

Figure 4

Using process

Introduction of the major function

The machine has good comprehensive performance, and nice appearance.

For the design on mute ,It adopts complete enclosed base frame and low-noise

motor, and thus reduces the working noise significantly. We can guarantee that the

purchase of this machine will bring you a clean world without disturbing your quiet life.

Using process

Cascade washing

The cascade washing it adopts can enhance

the strength of the water current, and dissolve

the detergent quickly and completely. At the

same time it can produce flushing effect, and

improve the washing effect.

Foam-removing spinning during high-efficiency rinsing

Use the foam-removing spinning to

remove the extra detergent liquid. It

can both shorten the washing time

and save the water consumption.

Spin

Remove most of
the foam extra
detergent liquid.

Fill water for
about 1 minutes

Remove the detergent
liquid remained

Foam-removing
spinning

Spin for about
1~2 minutes

The effect is best when the
laundries quantity is below
80% of the rated value.

Preparation before washing

Preparation before washing

1.Connect the water inlet hose.

2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.

3.Put down the drain hose .

4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.

Using process

Using process

Pay attention to followings before washing the laundries

Confirm if
there's special
requirement for
the laundries.

Clear the pocket.
Take out the
coins , sand,
hairpins etc.

Fasten the
buttons and
zippers.

The quantity of
the laundries
shall not exceed
the rated value.
The big laundries
like the jeans
shall be put in
loosely.

When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
discretion,please
put the laundries
with buttons into
other laundries.

The musts in washing

The capacity of washing and spinning of
the machine refer to the largest weight of
the standard laundries under dry condition
that can be washed or spinned in one time.
Laundries quantity in one washing cycle
shall be lower than the rated capacity.
The largest capacity of this machine is

9.0 kg.
The thickness ,size , type of the cloth will

influence the actual washing capacity. It
is suitable to put in reasonable amount of
laundries and the laundries can be turned
round in washing for one time washing.

Do not select " Max " water level for
laundries less than 4.0kg, so as to avoid
splashing of water.

Reference weight of the laundries

Using process

Using process

cotton,about 900g

Pajamas

Shirt

cotton,about

300g

Working suit up,down

Blanket

Undershirt

cotton,about 180g

cotton,about 1120g

Underpants

cotton,about 70g

Jeans about 800g

Blending coat

about 800g

Jacket

cotton,about

800g

Single bed sheet

cotton,about 600g

Socking

blending,about 50g

Using process

Usage of the detergent

Using process

How to use the whitener

Fill water to decided level. Dilute the whitener with container. Pour it slowly into the
washing tub.
Avoid using whitener on laundries with color or pattern as they are prone to lose color.

The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and quantity of the whitener.

For powder whitener, please dissolve it before using.

How to use the washing powder

Direct dissolved in the machine:

1.Fill small quantity of water.

2.Add the powder . Run for 30 seconds to
dissolve it completely.

3.Put it in the laundries. Select suitable
water level.
The instant dissolving of the washing powder:

1.Prepare warm water of 30 C and a container.

2.Add the powder while stirring to fully
dissolve it.

The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.

It is suggested not to use high sudsing
detergent.

Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.

Selection of the quantity of the washing powder list 1

Standard dosage

Laundries
quantity

6.4kg~9.0kg

4.0kg~6.4kg

Below4.0kg

Water level

Water quantity

Maximum (about83L)

Medium (about68L)

Minimum(about49L)

Concentrated washing
powder

About About

About About

About About

75g

61g

43g

Common washing
powder

83g

68g

49g

Selection of the current , water level and washing time list 2

Laundries
quantity

4.8kg~9.0kg

Below4.8kg

Current

Strong

Standard

Water level

Water quantity

Medium (about68L)
~

Maximum(about83L)

Minimum(about49L)

~

Medium (about68L)

Laundries

Knitwear
Cotton,blending,linen
Very dirty and thick
Bed sheet
Silk(thin laundries)
Chemical fiber
Cotton,blending,linen

Washing time
(minutes)

About3~6
About8~10
About10~13
About7~13
About2~4
About3~6
About8~10

Washing sequence

Using process

Using process

Water-filling selector

Wash timer

(To set to below 2 minute,
first set to 5 minute then
turn it back. it can increase
the service life of the timer).

OFF

SILK

WOOL

WASH TIMER

LINEN

Wash selector

(standard current,
strong current)

STANDARD

COTTON

WASH SELECTOR

STRONG

Buzzer

(The buzzer will ring when
the washing finishes)

OFF

MAX

DRAIN

BUZZER

Wash

1.Water-filling selector
Set the water inlet selector at the "WASH" side.
(Figure 1)

2. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
Run washing program for some time to stir and
dissolve the powder completely.

Water-filling entrance

XPB90-99GS

SPIN TIMER

WASH

Spin timer

(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).

OFF

SILK

WOOL

SPIN

Figure 1

Figure 2

3.Put in the laundries. If the water quantity is
insufficient, please add water.

4.Select the current.
Select the strength of the current according to
the laundries. (Figure 3)

5.Select the washing time
Select the washing time according to the laundries.
(Figure 4)

6.After washing, the buzzer will ring. Set the "WASH
SELECTOR" at "DRAIN". (Figure 5).

STRONG

STANDARD

WASH SELECTOR

WASH TIMER

STRONG

STANDARD

WASH SELECTOR

OFF

SILK

WOOL

LINEN

DRAIN

COTTON

DRAIN

Figure 3

Figure 4

Figure 5

Midway spinning

1.

Put the laundries into the spin tub evenly and smoothly.

2.

Spin

(1) Put the gland in properly.

Please put in the gland properly even if the laundries quantity is small.

Using process

Using process

Push

Proper Proper

(2) Close the inner and outer cover of the spin tub.

(3) Spin for 1-2 minutes.

3.

Run the foam-removing spinning.

(1) Open the outer cover of the spin tub.
(2) Set the water-filling selector control
rod at the "SPIN" side. Fill water for
about 1 minute.
If the water quantity filled is too large,
the water may flow out from the wash
tub side. Please twist the water tap to
limit the water filling.
(3) Close the outer cover of the spin tub.
Spin for 1-2 minutes.

Gland

The laundries
are slanting

Push

No gland

Outer cover of
The spin tub

Inner cover of
The spin tub

WASH

SPIN

Rinsing

Using process

Using process

Rinse with stored water

1. Put the laundries into the wash tub. Select suitable current according to
the laundries.

2. Fill water to preset water level.

3. Rinse
Adjust the wash timer to 2-3 minutes to do rinsing.

When the laundries quantity is below 4.0 kg, please use "STANDARD" current.
If you use "STRONG" current, it may splash.
If the water flows out from the overflow holes, it menas that water filling
quantity is too much.

(Repeat the midway spinning and
rinsing with stored water for 2-3 times)

OVERFLOW

If the water flows out of the
overflow holes,that is
overflowing,plaese twist the
water filling,to avoid influencing
the life of the machine

Spinning

Using process

Using process

1. Put the laundries into the spin tub
evenly and smoothly.

2. Press the gland in the tub properly.
Close the inner and outer cover of
the spin tub.

3. Spin
Select suitable spin time according
to the laundries, and do spinning.

During spinning, if there's abnormal
sound, it is generally owing to slanting
placement of the laundries. Please
stop the machine and re-order the
laundries.

In spinning, it will pause the work if you open the outer cover of the spin
tub. Close it to resume the spinning.

Selection of the spin time list 3

Laundries

Bed sheet or
blanket

Underwear
(knitwear)

Swear
(chemical fiber)

Blending thin
laundries

Spin time
(minutes)

About 4~5

About 2~4

About 1~2

Within 1 minute

To do spinning and draining together,
please first do spinning for around 1
minute, then do draining. Otherwise
the spinning will stop owing to too much
water stored in the spin tub.

Using process

Disposal after washing

After using, please clean the lint and foreign materials of the lint filter and lint frame
in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.

Using process

Cleaning the lint filter

The lint filter must be used during washing.
It must be cleaned in time after each using.

1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See to
Figure 1)

Figure 1

2. Clean the lint
Put it in water and clean while it is
still wet.(See to Figure 2)

Figure 2

3. Install the lint filter
After cleaning, insert the bottom
of the lint filter ( marked with
"down side") into the filter frame ,
then push the upper part of the
filter in ( marked with " up side ").
(See to Figure 3)

Cleaning the filter frame

Too much lint on the filter frame will influence
the normal usage of the machine. Please
clean it every two months.

1 Take off the filter frame.
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.

Figure 3

Elastic fixing
claw

Cleaning the filter frame

2. Cleaning the filter frame
Clean the lint around the frame
and flush with tap water.

3. Install the filter frame.
(1).Insert the mounting plate at
the bottom of the frame into
the valve cover.
(2).Hang up the hook at the left
upper side.
(3).Push the upper part in as
indicated in Figure 2.

Hook

Using process

Using process

Disposal of the complete unit

Wipe the complete unit with soft cloth

twisted dry.

Wipe with neutral detergent if too dirty

Do not wash it directly by water

Thinner

Petrol

Alcohol

After washing, dismount the water inlet
hose.
Do not store water in the tub for long
period. Discharge the water immediately
after each using.
Pull off the power plug and hang up the
power cord.
Hang up the drain hose.
Wipe off the water drops on the surface
and inside the tub with clean soft cloth.
Open the cover of the wash tub and the
inner/outer cover of the spin tub for
some time (about one hour), then close
them.

Trouble-shooting Answer to question

(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending
it to repair. If there are real breakdowns, please come to the special maintenance
department or after-sale service department of our company. Do not repair it by yourself.

Phenomena The reason

Is there power failure?

The machine does not act.

The draining does not work

Is the power plug loose?
Is the pulsator twisted by foreign materials?

Is the drain hose put down?
Is the drain hose frozen?
Is the drain hose blocked by foreign material?

There's abnormal sound
during washing

There's abnormal sound
and violent vibration
during spinning

There may be some water
flowing out of the drain
hose in the first use of
the machine.

Are there hair pin, coins or metal items brought
inside the tub?

Is the machine slanting?
Is the gland pressed evenly?
Are the laundries in spin tub too much?

It is the water remained in the factory inspection
of performance.

When the remained water is frozen

Prevent the freezing (be sure to discharge the water completely after using)
After complete draining, set the "WASH SELECTOR" at "STRONG" or "STANDARD".
If it is set at "DRAIN", it will be rather difficult for the frozen water to melt.

When the water is frozen
Pour hot water below 50 into the wash tub
to soak it completely. Then turn the pulsator
with hands gently. Please confirm the drainage
can work normally before next using.

Packing list

User's manual

Water inlet hose

Gland

Twin-tub washing machine

One

One

One

One

Specification

Type

Model

Power source

Water level Water quantity about

Rated washing capacity kg

Rated spinning capacity kg

Rated input power W

Dimension(mm)

Wash pattern

Weight kg

Injection pressure

Twin-tub washing machine

XPB90-99GS

Rated voltage 120V~,Rated frequency 60Hz

High/83L Medium/68L Low/49L

9.0

7.8

Wash 560 Spin 260

L876 W500 H986

New current + cascade

43.5

0.02MPa~0.2MPa