Haier 42HP25SAT, 42HP25BAT, 42EP25SAT, 50HP25BAT, 42EP25BAT User Manual
PLASMA TV
OWNER S MANUAL'
MODEL :42EP25BAT
S
42EP25SAT
42HP25BAT
42HP25SAT
50HP25BAT
Please READ this manual carefully before
operating your TV, and retain it for future
reference.
WARNING
RISK ELECTRIC SHOOK
DO NOT OPEN
WARNING : To reduce the risk of electric shock do not remove cover or back.
No user-serviceable parts inside refer service to qualified service personnel.
Safety of operators has been taken into consideration at the design and manufacture
phase, but inappropriate operation may cause electric shock or fire. To prevent the product
from being damaged, the following rules should be observed for the installation, use and
maintenance of th product. Read the following safety instruction before starting the operation.
The User Manual uses the following symbols to ensure a safe operation and prevent
any damage to operators or properties:
THIS SYMBOL INDICATES THAT HIGH VOLTAGE IS PRESENT
INSIDE. IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT
WITH ANY INSIDE PART OF THIS PRODUCT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, use and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However ,there is no
guarantee that interference with not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encourage to try to correct the interference by one or
more of the following measures:
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
*Consult the dealer or an experienced radio/TV technician for help.
This device compiles with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may be not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC CAUTION:
To assure continued compliance and possible undesirable interference, the provided ferrite
cores must be used when connecting this plasma display to video equipment; and maintain
at least 40cm spacing to other peripheral device.
CANADIAN NOTICE:
This Class B digital apparatus compiles with Canadian ICES-003.
2 PLASMA TV
IMPORTANT SAFETY INSTRUCTIONS
Read all of the instructions before using this appliance. When using this
appliance, always exercise basic safety precautions, including the following:
1)Save these Instructions ---the safety and operating instructions should be
retained for future reference.
2)All warning on the appliance and in the operating instructions should be followed.
3)Cleaning --- Unplug from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use only dry cloth for cleaning.
4)Attachments ---do not use attachments not recommended by the manufacturer
as they may cause hazards.
5)Water and moisture -- do not place this product near water, for example, near a
bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a
swimming pool.
6)Accessories ---do not place this unit on an unstable cart, stand, tripod, bracket,
or table. Use only with a cart, stand, tripod, bracket, or table recommend by the
manufacture, or sold with the unit.
7)Ventilation ---Slots and openings in the cabinets and the back or bottom are
provided for ventilation. These openings must not be blocked. In a built in
installation such a bookcase or rack do not install product unless proper ventilation
is provided.
8)Power Source ---this TV should be operated only from the type of power source
indicated on the rating label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company.
9)Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet. To prevent electric shock, ensure
the grounding pin on the AC cord power plug is securely connected.
10)Power cord protection ---Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against them. Pay
particular attention to cords or plugs, convenience receptacle, and the point where
they exit from the appliance.
11)Lighting precaution ---for added protection for this product during a lighting
storm or when it is left unattended for long period of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage to the
product due to lighting and power line surges.
12)Never push objects of any kind into this product through openings as they may
touch dangerous voltage point or short out parts that could result in a fire or electric
shock. Avoid spilling liquid of any kind on the product.
13)Servicing ---do not attempt to service the product by yourself, as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to authorized service personnel.
14)Unplug this unit from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power supply cord or plug is damaged or frayed.
Owner s Manual 3
b.If liquid has been spilled, or objects have been fallen into the unit.
c.If the unit has been exposed to rain or water.
d.If the unit does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions, as
improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the unit to its normal
operation.
e.If the unit has been dropped or damaged in any way.
f.When the unit exhibits a distinct change in performance; this indicates a need
for service.
15)Heat --- The product should be situated away heat source such as radiators, heat
registers, stoves, or other products (Including amplifiers) that product heat.
16)Overloading ---Do not overload wall outlets and extension cord as this can result
in a risk of fire or electric shock.
SAVE THESE INSTRUCTIONS
Thank you for using our Haier product. This easy-to-use manual will guide you in
getting the best use of your product. Remember to record the model and serial
number. They are on label in back of the unit.
Model number
serial number
Date of purchase
Staple your receipt to your manual. You will need it to obtain warranty service.
4 PLASMA TV
Contents
Introduction
War nin g . . . . . . . ...... ... ... .. . . . . . . . . . . . . . . . . . . . . . . .
Saf ety I nst ruc tio ns . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Introduction
Con tro ls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ... ... ... ..
Connection Options . . . . . . . . . . . . . . . . . . . . . .............
Universal Remote Controller . ............ . . . . . . . . ......
Installation
Acc ess ori es . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... ...... ..
Install the speaker..................................................
Install the stand.....................................................
Antenna Connection . . . . . . . . . . ..............................
VCR Connection. . . . . . . . . . . . . . . . . . . . ................. ..
External A/V Source Setup . . . . .. . . . . ......................
DVD Connection . . . . . ...... . . . . . . . . . . . . . ................
DTV Connection.....................................................
Digital Audio Output . . . . . . . . . . . . . . . . . . . . ..............
PC Connection. . . . . . . . . . . . . . . . . . . . . . . ................
Monitor Out Setup . . . . . . . . . . . . . . . . . . . . ............... .
HDM I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..... ... ... ... ... .
Cable sample.........................................................
Connecting Headphones . . . . . . . . . . . . . . . . . . . ....... .
Pow er so urc e.. ... ...... ... .. . . . . . . . . . . . . . . . . . . . . . . . . .
Operation
Switching On/Off the TV set . . . . . ... . . . . . . . . . . . ... ...
Choose the Menu Language . . . . ..... .......................
Choose the input source.........................................
Channel Menu
Automatic Scan. . . . . . . . . . . . . ............................. . .
Man ual S can . . . . ... ... ...... .. . . . . . . . . . . . . . . . . . . . . .. .
Fine tune................................................................
Edi t Pro gra m.. ... ...... ... . . . . . . . . . . . . . . . . . . . . . . . . . ..
elect the desired program
S . . . . . ........... ............ . . ..
elect the desired sound
S . . .............. . . . ............ . . ..
Mute .............. . . . ............................................ . . ..
Video Menu
How to select picture modes.....................................
How to customize your own picture status .................
Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . .. . . .. . . ..
Audio Menu
How to select audio modes......................................
How to customize your own audio status ..................
SAP Broadcasts Setup............................................
Timer Menu
Date /Time setting...................................................
Timer on setting......................................................
Timer off setting......................................................
Sleep Timer setting.................................................
Time zone setting...................................................
Daylight Saving setting...........................................
Function Menu
Closed Captions.....................................................
CC mode...............................................................
NTSC Caption
DTV Caption..........................................................
DTV Caption Style..................................................
OSD Timeout
Blue screen
OSD transparency
Adjust
Menu
Screen Setup for PC mode......................................
Lock Menu
Parental Control rating and categories.......................
Others Functions
EPG (Electronic Program Guide) . . . . . . . . . . . . .........
Bri ef In fo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ... ... ... . .
Quick program view.................................................
Veiwing Picture- in- Picture
Setting up your remote control ..................................
Remote Control Codes ............................................
Maintenance . . ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
........................................................
.........................................................
...........................................................
..................................................
.....................................
Warranty ................................................................
Manufactured under license from Dobly Laboratories. "Dobly" and the
double-D symbol are trademarks of Dobly Laboratories. Confidential
unpublished works.
Copyright 1992-1997 Dolby Laboratories. All right reserved.
Owner s Manual 5
Controls
-This is a simplified representation of front panel.
-Here shown may be somewhat different from your TV.
Front panel controls
Introduction
42EP25BAT
50HP25BAT
42HP25BAT
EXIT INPUT MENU
CH-
42EP25SAT 42HP25SAT
1.EXIT
returns to TV viewing from any menu.
2.INPUT:
confirm.
3
.CH(+/-) Program plus and minus, menu
options
4.VOL(+/-) Volume increase and decrease,
menu reset and entry
INPUT
CH-
EXIT
CH+ VOL- VOL+
MENUVOL+
VOL-
CH+
5.MENU Menu display
6.
7
. Remote control signal receive window.
8.Remote Indicator In red when standby
mode, in blue when display.
clears all on-screen displays and
all input source display and OK
POWER : Power on or off button.
1
6 PLASMA TV
1.VIDEO input
2.L-AUDIO-R left and right audio input.
3. EXIT: clears all on-screen displays and returns to
TV viewing from any menu.
4. INPUT: Source input select.
5.CH- /CH+: Program plus and minus, menu options.
6. VOL-/VOL+: Volume increase and decrease, menu
reset and entry
7.MENU: Menu display
8.Power: Power on or off button.
2
4
3
5 6
7
8
Connection Options
Back panel controls
Introduction
42EP25BAT
Audio input
for linking PC audio
output terminals.
PC
Audio In
PC VIDEO Input
Connect the monitor
output connector from
a PC to the jack
DVD/DTV Input
(Component )
Connect a component
video/audio device to
these jacks.
42HP25BAT
Digital Audio Output
Connect digital audio
from various types of
equipment. Note: In
standby mode,
these ports will not
work.
Y
PrPb
DVI Audio In
DVI Audio Input
Connect the audio out from
the external device, used
while using a DVI to HDMI
connector.
42EP25SAT 42HP25SAT
S-Video Input
Connect S-Video
out from
an S-VIDEO
device to the S-VIDEO
input.
LR
HDMI
HDMI/DVI
connect a
DVI(Video)
signal to
HDMI/DVI.
Optical
Optical Audio Output
Headphone
out
S-video
YPbPr
Audio In
Earphone jack:
Earphone audio
output terminal.
Connects the video
VIDEO Input
signal from a
video device.
RL V
S-video/CVBS
Audio In
CVBS
AUDIO/VIDEO
AUDIO Input
connect to hear
stereo sound from an
external device.
Antenna Input
Connect cable or
antenna signals to
the TV, either directly
or through your
cable box.
AV OUT
output
AUDIO output
LR
F
R INPUT
This TV operates on AC power.
The voltage is indicated on the
Specifications page. Never attempt
to operate the TV on DC power
AUDIO OUT
Power Cord Socket
AC IN
50HP25BAT
Power Cord Socket
This TV operates on AC power.
The voltage is indicated on the
Specifications page. Never attempt
to operate the TV on DC power
for linking PC audio
output terminals.
AC IN
PC
PC VIDEO Input
Connect the monitor
output connector from
a PC to the jack
DVD/DTV Input
(Component )
Connect a component
video/audio device to
these jacks.
Audio input
Audio In
Digital Audio Output
Connect digital audio
from various types of
equipment. Note: In
standby mode,
these ports will not
work.
Y
PrPb
DVI Audio In
DVI Audio Input
Connect the audio out from
the external device, used
while using a DVI to HDMI
connector.
HDMI
HDMI/DVI
connect a
DVI(Video)
signal to
HDMI/DVI.
Optical
Optical Audio Output
S-Video Input
Connect SVideo
out from
an S-VIDEO
device to the S-VIDEO
input.
LR
YPbPr
Audio In
Headphone
out
Earphone jack:
Earphone audio
output terminal.
LR
S-Video
VIDEO Input
Connects the video
signal from a
video device.
CVBS
AUDIO Input
connect to hear
stereo sound from an
external device.
RL V
S-video/CVBS
Audio In
Antenna Input
Connect cable or
antenna signals to
the TV, either directly
or through your
cable box.
AV OUT
AUDIO/VIDEO
output
F
R INPUT
Owner s Manual 7
Universal Remote Controller
- The remote controller cannot be operated unless the batteries are properly loaded.
- When using the remote control, aim it at the remote control sensor on the TV.
Introduction
Function introduction
Turns your TV or any other programmed
equipment on or off, depending on mode.
Open the channel list.
PIP:Selects PIP, PBP and main Window;
SWAP:In PIP and PBP mode, swap the
AUDIO SWAP: In PIP and PBP mode,
swap the audio of main and sub window;
PIP function buttons
main and sub window;
PIP position: To select sub picture
Selects the picture appropriate
for the program's character.
CC(closed caption)
Select a closed caption:
CC MUTE, CC ON, CC OFF.
Shows program schedule.
Brings up the main menu to the screen.
Clears all on-screen displays and
returns toTV viewing from any menu.
Switches the sound on or off
(Aspect Ratio Control)
It is not available under PIP mode.
Changes the aspect ratio.
It is available under PBP mode.
VOLUME UP/DOWN
Increases/decreases the sound level.
POWER
CH.LIST
position for PIP.
P.MODE
GUIDE
MENU
EXIT
MUTE
ARC
TV DVD VCR SETBOX CABLE AUDIO
Press the SELECT button repeatedly to select one of the
system modes in which the remote control can be used.
When the desired device is selected, the corresponding
LED lights on 5seconds.
FAVORITE
Open the favorite channel list. Select the subchannel
CH.LIST
PIP SWAP
FAV.LIST
AUDIO LIST
AUDIO SWA P
SEL ECT
POSITION
S.MO DE
P.MODE
CC
UIDE
U
N
E
FREE ZE
NPUT
INFO
AUDIO.LIST
Open the audio channellist.
VCR/DVD Functions
Control some video cassette recorders or DVD players.
/ Rewind / Fast
/ backward /Forward
Stop
Play/Pause
REC
S.MODE
Selects the sound appropriate for the program's
character.
FREEZE
Freezes the currently-viewed picture, but audio continues.
Press FREEZE button again to resume the normal picture.
INPUT
show the input source mode.
OK
E
X
IT
A
R
C
VOL +
VOL-
P
E
E
L
S
P
A
S
CH+
CH-
INFO
When you watch the TV, press the key, the information
displays on bottom of the screen.
THUMBSTICK
(Up/Down/Left/Right/OK)
Allows you to navigate the on-screen menus and adjust
the system settings to your preference.
SLEEP button
Displays the Sleep Timer option.
LIGHT
Press the light button, white LED will be ON, release
this key, white LED will be OFF.
SAP
Selects MTS sound: Mono, Stereo, and SAP in Analog
mode. Change the audio language in DTV mode.
CHANNEL UP/DOWN
Selects available channels
Numeric buttons
press to change the channel.
Press to select additional channels
being broadcast by the same station.
“54-3”, press “54”, then press “-” and “3”.
For example, to select channel
8 PLASMA TV
(digital and analog)
- button
Q.VIEW
Q.VIEW
Switch the current channel to the last channel
you have viewed, or switch the other source to TV.
Accessories
42EP25BAT
SELECT
CH.LIST
FAV.LIST
AUDIO LIST
PIP SWAP
AUDIO SWAP
POSITION
S.MODE
P.MODE
FREEZE
CC
E
N
D
P
I
U
U
T
I
N
F
U
O
N
E
OK
P
E
E
X
E
I
T
L
S
A
R
P
C
A
S
VOL+
CH+
VOL-
CH-
Q.VIEW
Remote controller
Alkaline battery(AAA) 2
M4X12 x8Screws
42HP25BAT
PLASMA TV
OWNERS MANUAL'
Owner`s manual
M5X16 x4Screws
42EP25SAT
Power cable
42HP25SAT
Speaker unit(X2)
Brace pole x2
Connection cord
Standx1
(
50HP25BAT
SELECT
CH.LIST
FAV.LIST
AUDIO LIST
PIP SWAP
AUDIO SWAP
POSITION
S.MODE
P.MODE
FREEZE
CC
E
N
D
P
I
U
U
T
I
N
F
U
O
N
E
OK
P
E
E
X
E
I
T
L
S
A
R
P
C
A
S
VOL+
CH+
VOL-
CH-
Q.VIEW
Remote controller
PLASMA TV
OWNER S MANUAL'
Owner`s manual
Power cable
Alkaline battery(AAA) 2
Owner s Manual 9
Install the Speakers(42EP25 AT/42HP25 AT/ )B B 42EP25SAT/42HP25SAT
1 Face the PDP screen upside down on a clean blanket or a bracket and pay attention not to indent the casing. (See figure),
Нв¹ТСпЙщЖчК¹УГЛµГч
lay the two speaker aside of the PDP.
2 Insert the pothook to the faucet of the PDP screen .
3 Fix the speaker to the PDP with the screws 4-ST 4X16 .
25.400
\U+2592\U+255A\U+2514\U+00B2
Before turning on the PDP , ensure you have connected the line between the speaker and the PDP
Connect the speaker to the speaker terminal of plasma screen:
Press the speaker terminal and insert the connecting cable into the terminal slot.
Release the speaker terminal and ensure that the white connecting cable is inserted in the terminal slot marked red and black connecting
cable is inserted in the black terminal slot, and that anode and cathode poles are correctly connected. (See Figure )
25.400
\U+2592\U+255A\U+2514\U+00B2
EXT SPEAKER
L R
The left speaker
The right speaker
10 PLASMA TV
Install the Stand
Insert the supporting bracket with 8 M4x12 screws to
the installation holes on the bottom of the soleplate.
Fasten the Supporting bracket and the Soleplate
as shown in figure.
Install the Stand to the PDP
Face the PDP screen upside down on a clean blanket or the bracket and pay attention not to indent the casing.
Lay down the stand and put it to responding position of the PDP screen ,and make sure the brace pole towards the hole of the PDP .
Fix 2 PDP brace pole to the PDP on the back of the plasma display with 4 M5X16 screws.
Owner s Manual 11
Installation
- The TV can be installed in various ways such as on a wall, or on a desktop etc.
- The TV is designed to be mounted horizontally.
GROUNDING
Ensure that you connect the earth ground wire to prevent possible electric
shock. If grounding methods are not possible, have a qualified electrician
install a separate circuit breaker. Do not try to ground the unit by connecting
it to telephone wires, lightening rods, or gas pipes.
External Equipment Connections
Antenna Connection
Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an
outdoor antenna .In different places, the suitable antenna type and position are different.
VHF Antenna
UHF Antenna
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall Antenna
Socket
Bronze Wire
RF Coaxial Wire (75 ohm)
Turn clockwise to tighten.
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor
Antenna
Bronze Wire
Be careful not to bend the bronze wire when
connecting the antenna.
To improve the picture quality in a poor signal area,
please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV`s, install a 2-
Way Signal Splitter in the connections.
If the antenna is not installed properly, contact your dealer
for assistance.
12 PLASMA TV
External Equipment Connections
NOTE: All cables shown are not included with the TV.
Choose Your Connection
There are several ways to connect your television, depending on the components you want to connect
and the quality of the signal you want to achieve. The following are examples of some ways to connect
your TV. Choose the connection which is best for you.
VCR connection
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV
Connection Option 1
Set VCR output switch to channel 3 or 4 and
then tune the TV to the same channel number.
Installation
Connection Option 2
1. Connect the audio and video cables from the
VCR's output jacks to the TV input jacks, as
shown in the figure.
When connecting the TV to VCR, match the
jack colors (Video = yellow, Audio Left = white,
and Audio Right = red).
If you connect an S-VIDEO output from VCR to
the S-VIDEO input, the picture quality is
improved; compared to connecting a regular
VCR to the Video input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner`s
manual.)
3. Select the input source with using the
INPUT button on the remote control, and
then press / button to select the source,
press the button to confirm.
S-Video
LR
CVBS
RL V
S-Video/CVBS
Audio In
AV OUT
F
R INPUT
Owner s Manual 13
External Equipment Connections
External A/V Source Setup
How to connect
Connect the audio and video cables from the external equipment's
output jacks to the TV input jacks, as shown in the figure.
When connecting the TV to external equipment, match the
jack colors (Video = yellow, Audio Left = white, and Audio
Right = red).
How to use
1. Select the input source with using the INPUT button on
the remote control.
2. Press the / button to select the desired source.
3. Press the ok button to confirm
2. Operate the corresponding external equipment.
S-Video
LR
CVBS
RL V
S-Video/CVBS
Audio In
AV OUT
Installation
F
R INPUT
Camcorder
Video Game Set
DVD connection
How to connect
1. Connect the DVD video outputs (Y, Pb/Cb, Pr/Cr) to the Y, Pb,
Pr jacks on the TV and connect the DVD audio outputs to the
YPbPr Audio IN jacks on the TV, as shown in the figure.
2. If your DVD only has an S-VIDEO output jack, connect this
to the S-VIDEO input on the TV. as shown in the figure.
NOTE: If your DVD player does not have component video
output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the INPUT button on the remote control to select YPbPr
mode.
3. Press Play button on external equipment for program play.
4. Refer to the DVD player's manual for operating instructions.
Component Input ports
To get better picture quality, connect a DVD player to the component
input ports as shown below.
Component ports
on the TV
Y Pb Pr
Y
Pr Pb
DVI Audio IN
LR
YPbPr
Audio In
Headphone
out
S-Video
LR
CVBS
S-Video/CVBS
Audio In
Video output ports
on DVD player
14 PLASMA TV
Y Pb Pr
Y B-Y R-Y
Y Cb Cr
Y P P
BR
Installation
External Equipment Connections
DTV connection
- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital
signals from a digital set-top box or other digital external device, refer to the figure as shown below.
- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).
How to connect
Use the TV`s (Y, PB, PR ) , VGA or HDMI
jack for video connections, depending on
your set-top box connector. Then, make
the corresponding audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the owner`s
manual for the digital set-top box.)
2. Use INPUT on the remote control to select
YPbPr, VGA,or HDMI source.
Signal
480i
480p
720p
1080i
YPbPr
Yes
Yes
Yes
Yes
HDMI/DVI
Yes
Yes
Yes
Yes
Digital Audio Output
Send the TV`s audio to external audio equipment (stereo system) via
the Digital Audio Output (Optical) port.
How to connect
1. Connect one end of an optical cable to the TV Digital Audio
(Optical) Output port.
2. Connect the other end of the optical cable to the digital audio (optical)
input on the audio equipment.
See the external audio equipment instruction manual for operation.
Y
Pr Pb
PC
Audio In
DVI Audio IN
HDMI
LR
Optical
YPbPr
Audio In
Headphone
out
Digital Set-top Box
LR
HDMI
Optical
YPbPr
Audio In
Headphone
out
Note: When connecting with external audio equipments, such as
amplifers or speakers, please turn the TV speakers off.
Caution: Do not look into the optical output port.
Looking at the laser beam may damage
your vision.
Owner s Manual 15
Loading...