Page 1
Fully Automatic Washing Machine
User's manual
This manual is for
50FREE-1
Please read this manual
carefully before using.
Retain it for future reference.
Special number:0030805887A
Page 2
CONTENTS
Specification the 2nd cover
Names of the parts 1
Safety precautions 2
Installation and adjustment 4
Install the water inlet hose 6
Preparation before washing 8
Put in the laundries 9
Usage of the detergent
Use the operation buttons 10
Finish washing 13
Disposal after washing 14
Trouble-shooting answer to question 15
Packing list 16
9
9Close the top lid
Specification table
Water level/Water
Water Injection pressure
Rated washing / spinning capacity
quantity (about)
0.03MPa 1MPa
~
5.0kg/5.0kg
Page 3
Packing list
Names of the parts
User's manual
Warranty card
Water inlet hose
The side of connection between the water inlet
hose and the washing machine
The side of connection between the jointer of
the water inlet hose and the water faucet
Bottom plate
Inner cover component
Automatic washing machine
Quantity
One
One
One
One
Inside in inner tub of washing
machine
One
Inside in inner tub of washing
machine
One
Top lid component
Control pannel
Liquid detergent inlet
Filter frame
Balance ring
Lint filter
Inner tub
Pulsater
Front control board
Cabinet
Base frame
Inner cove
component
Detergent box
Attachment block
(2 pieces)
Handle
Drain hose frame
Drain hose
Adjustable leg
film
Adjustable leg
Meaning and description of the symbols
Warning sign
Contents marked with that symbol are related to the
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.
Water inlet valve
Water absorption
cushion
Fixed leg
Power cord
Back cover
(3 pieces)
Forbidden sign
Contents marked with that symbol are actions forbidden
to perform. Performing of those action may result in
damage of the machine or influence the personal safety of
the users.
1
Page 4
Safety precautions
Please plug the power plug on special receptacle.
Be sure to use three-pins power receptacle. Ensure
that the earthing prong of the power receptacle is
earthed reliably. Use leakage protector if possible.
Earth
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or our customer care agent.
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
The ventilation
holes at the bottom
Carpet
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
The washing machine must be positioned so that
the plug is accessible. Be sure to pull the plug off
and close the water faucet in following cases:
power failure, delivering the machine, setting the
machine idle or cleaning the machine. Do not plug
or pull the power plug with wet hand.
Do not use water hotter than 50 .
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning and
damages to the laundries.
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not
breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.
Phenomena The reason How to settle
The digitron displays E0.
The drainage cannot work, or is too slow.
The digitron displays E1.
It stops running in midway. The digitron
displays E2.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
The water filling does not work, or is
slow. After a period of time, the digital
displays E4.
The digitron displays E6.
Not wash
The machine does
not act
Not spin
There's abnormal sound
inside the machine
The water faucet leaks
Common phenomena
The top lid is opened during reserve procedure.
Is the drain hose blocked?
After long running of pump in the hot
weather, power will be cut automatically for safe.
The top lid is not closed.
Are the laundries put slantingly?
Is the machine slanting?
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
The water level sensor is bad.
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
Is the jointer of water inlet hose loose
or awry?
Close the top lid.
Clean the foreign material. Open and close The top Lid Once.
Some minutes later the machine will
continue to work
Close the top lid.
Reorder the laundries.Close the top lid.
Th machine will start running after 10
seconds of being placed horizontally.
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the start/Pause button once.
Push the Start/Pause button once.
Please contact the customer care
agent.
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Fasten the jointer properly.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
2
Phenomena Explanation
The spinning is intermittent when it starts.
The wash procedure is paused.
Push the SPIN button , but it doesn't work.
The pulsator pauses during water inlet
in wash and rinse.
There may be some water flowing out of the
drain hose in the first use of the machine.
Balance the laundries to avoid slanting.
The cloth sensor is checking the cloth, it willadd waterafter 48 seconds.
The program is setting the drain time. Some time is needed
before it starts spinning.
It is to avoid splashing during water inlet.
It is the water remained in the factory inspection of performance.
Page 5
Disposal after washing
Safety precautions
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Clean the detergent box and set it on
the control panel seat.
1.The method of dismantle:Push it up aslant and
gently.
2.The method of install : install it upwards and aslant
and push it in .
Dismantle Install
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
Please clean it with brush every two months.
The lint filter must be used during washing.
It must be cleaned in time after each using.
Lint filter:
1.Push down the spring piece of the top lint filter to
make the claws out of the filter cover, and then
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and thenyou can get
down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it tight .
6.Make sure the lint filter well installed, or it can
influence your use.
Up
Install
Install
Figure 1
The back cover of lint filter
Up
Dismantle
Dismantle
Down
The front cover of lint filter
Down
Figure 2
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
Do not put hand into the rotating tub. It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
The handicapped or children without care shall not use
the machine.
Do not decompose, repair or alter the machine by
yourself.
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
Petrol
Benzene
Keep the machine away from direct sunlight and
heat source like the heater.
Petrol
Benzene
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
lint filter is lost or damaged,please contact the local
after-sales service department of our company.
Install
Dismantle
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand,
hairpin and other foreign materials before washing.
Please check if the water faucet is open, and if the
connection of the water inlet pipe is proper. p
ut
up the drain hose
It is suggested to use foamless washing powder.
Page 6
Installation and adjustment
Please install and adjust the machine according to the requirement of the mannual.
It is very important to your security and correct operating the machine.
Install the inner cover
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover,
aiming the inner cover shaft to the installation hole of the
corresponding outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of one side into the
corresponding outer tub cover shaft groove, then push
the another inner cover shaft into the corresponding outer
tub cover shaft groove. Please install to designated position
to guarantee there are no dropping or abnormal sound in
opening and closing of the inner cover, and the operation
shall be smooth. Do not dismount the inner cover component
after washing.
Section • enlarging
Push
Outer tube cover
Outer tube cover
shaft groove
Inner cover shaft
Damping cushion
Inner cover components
Install the bottom plate
After you open the package, please lean
the washing machine gently down on soft
items ( like the towel cloth, blanket, etc. ).
Install the bottom plate to the bottom of
the machine, then lift the machine up gently.
See to the figure:
Bottom plate
Back
Front
Soft items
Adjust the Installation position
The distance that washing machine away from wall should be above 20mm. The largest allowed slope of the
shank base of the machine is 2 . The slanting or rough ground will result in unstable running or stoppage
of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
2 . After adjustment, fasten the nut.
Loosen
High
the adjustable nut
Fasten
the adjustable feet
Low
The soak procedure can work in cooperation with automatic programs like standard, carpeting
fiber.There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing,
and can not make setting in other cases.
The function of Softener will be chosen at the same time as sterilize is selected ,when the
sterilize is not chosen ,there will be no water flowing into the box for thesoftener preparation.
So do not add softener preparation into the box to aviod wasting
If the water pressure is too low,in order to wash the closes cleanly,the machine will change
from " saving water "to "storing water "automatically.
er
Wat
evel
l
4 Push the " water level "button,select suitable water level
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "start/pause"
button, then push the "water level" button to set the water level.
Air-dry
5. Push the "Air-dry "button,select Air-dry
Air-drying could reduce time drying in the sun; fibre could be
dress on after ironing
6 Push the "reserve" button to select suitable
Reserve
reserve wash program
After switching on the power, the reserve program is set to off mode automatically. If you need to
set the washingprocedure to be finished at reserved time, please push the " reserve " button to
set the reserve wash program. Refer to reserve button in Page 11 for selection.
Confirm the operation of reserve program
When the "reserve" function is activated, the indicator light of the program
you have set will be off. The "reserve (hour)" and "time remain" indicator
lights will be on. During reserve procedure, push the "reserve" button to
display the reserve mode.
To change the running program or cancel the reserve setting, you need to
switch off the power and make new selection.
7 Push the "Start/Pause" button
the washing will finish
about 18 hours later
Start
Pause
6 Finish washing
After finishing wash it'll alarm automatically
Page 7
Steps of using the operation buttons and
Start
Paus
e
Soak
W
as
h
e
S
teriliz
e
Spin
oak
Wash
R
in
se
S
te
rilize
S
pi
n
description of the steps
b
Sterilize
Soak
Wash
20
15
Pause
7
W
as
h
RinseRins
S
terilize
3
Spin
Rinse
Thrice
Twice
Once
Spin
Reserve
Lock
6
1.Push "power" button to switch on the power
2.Push "program" button to select suitable
full-auto program
After the power is switched on, "standard" is automatically set. To select other full-auto program, please push
the "program" button till the corresponding indicator is on. Refer to the "Program button" on Page 11.
E.g. Set to "Superfast" program for small quantity of laundries with light soil.
In selecting the standard program, the machine will execute fuzzy program to select water
and wash time according to the cloth and weight of the laundries. The full procedure is controlled
automatically.
carpeting
45L
42L
36L
39L
32L
29L
22L
26L
14L
18L
Water
el
lev
4
Air dry
Standard
Save
Fibre
Superfast
Wool
Air-dry
am
Progr
2
er
ow
P
m
ra
og
Pr
How to change the direction of the drain hose
1.Dismantle the back cover.
Power
2.Put down the drain hose.Take off the drain
hose rack.Pull the drain hose into the cabinet
5
from the left side of the bottom.
Using the drain hose
The drainage shall be smooth with the drain hose.
1.put the drain hose up to suitable position (Do not
put it on ground.)
Notes: The highest point of drain pipe shuold be
higher than the water level of washing tub for
avoiding to siphon phenomenon during drain.
3.Protrude the drain hose from the hole on the right side
of the bottom,and fasten it onto the bottom with rack
and screw.
4.Install the back cover.
2.Do not step on or press the drain hose.
3 Push "soak", "wash", "rinse/sterilize", "spin" button to select suitable
procedure program
Attention
Even there's no water in the tub, a certain period is required before spin starting.
Separate the laundries that are not colorfast from other laundries in washing.
The pulsator will not rotate unless the water is filled to selected water level.
SoakS
Wash
Spin
se
in
R
S
terilize
12
0.8m<H<1.2m
5
Page 8
Install the water inlet hose
1. Attach the water inlet hoses to the water faucet. Using pliers, tighten
the coupling. ( As figure 1)
NOTE: Do not over tighten. Damage to the
valves can result.
Reserve, remain time digitron
It displays "--" during detecting.
It displays remained reserve time (hour).
It displays total remained time (min).
It displays abnormal symbol in abnormal situation.
(See to Page15)
"Power" button
Push the "power" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "power" button to switch on the power. If
the "start/pause" button is not pushed, the machine
will switch off the power automatically after 5 minutes.
2. Connect the other ends to the water inlet valve .
( As figure 2)
Jointer of the water inlet hose
Jointer of the
water inlet valve
Water absorption cushion
Figure 2
Figure 1
Reserve
Lock
"Reserve" button
The digitron displays remain time
before washing is finished (in minutes)
Push "reserve" button, the digitron
displays the reserve time of washing
(in hours). The indicator flashes to
indicate that the reserve function
is operating.
Push "reserve" button to display
the reserve mode.
42L
36L
29L
22L
14L
Water
carpeting
45L
Fibre
39L
Wool
32L
26L
18L
level
"Water level" button
The washing machine can detect the laundries
automatically in standard program.
After detection,it will set the water level to suitable value
among 4, 6, 8,and 10 automatically.
You can also set water level by yourself. After the
machine is started, it will not set water level automatically.
You shall push the start/pause button to make new
setting.
If there's water inside the tub, the machine cannot detect
the laundries and will display water level 32L .
If wet laundries are put in, it may display water level 45L .
You must set suitable water level by yourself.
If superfast program is selected, it will display water
level 22L . When water level 18L is reached in water
filling, it will perform washing while filling water.When
water level 22L is reached, it will change to normal
washing.
During operation of wash and rinse program, you can
push down the water level button to add water. When
you release the button, or it reaches the overflow water
level, the machine will stop adding water.
The water level decided may be different from actual
value because of the different moisture level of the
laundries.
Progra
Standard
Save
Superfast
me
Air dry
Air-Dry
"Air- "
Dry button
"air- ry"
Push the d button ,then the
"air- ry"indicator light that
d is on,
Power
means the "air- ry"program is
chosen.
laundrie at the same time can
dry the outer tub and the inner tub ,
which can avoid growing mildew
on the outer tub and the inner tub.
The max drying capacity of the fibre
laundrie is 1.5 kg.
d
The purpose is drying
"Program" button
Following full-auto program is available
Program
Standard Common washing
Save
Superfast
Carpeting
Fibre
Wool
Remark:
If you want to wash wool silk or other top grade
laundries ,please select wool program
Application
washing for light-soil saving laundriesl
Washing for light-soil a few laundries
washing for carpet or heavy thickness
and damnify large laundries--usually
under 3kg
washing for fibre laundries
For silk textiles slap-up
usually under 2.5kg
laundries
Page 9
5 Push operation button
Soak
Wash
Rinse
Spin
Start
Pause
a
Description of operation button
Indicator mode and meaning
Off
Flashing, indicating the running program
On, indicating the program about to run or
the selection mode
Start/paush button
After the power is switched on,press it to
start the machine
During working,push it to pause.
During pause,push this button to restart
and go on working
Pause
Child lock function
Push and hold the reserve button and spin button, then push down the
power on/off button .The digitron displays C L .You can continue setting
desired washing procedures. After setting ,push down the start/pause
button. The child lock function is activated. all of the buttons are locked
and cannot make selection .
Release the child lock function :push down reserve button and spin
button at the same time for more 2 seconds .After a beep sound ,the child
lock function is released.
S
tart
Sterilize
Soak
Soak
Wash
20
15
Wash
Thrice
Twice
Once
Sterilize
Rinse
Spin
Spin
Lock
Check the connection between the water inlet
hose and the water tap
1.Swaying the hose gently to confirm if it is fastened
stable.
2.After installation, open the tap to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the water inlet hose and the water tap is firm,
so as to prevent dropping from improve Installation
position.
Take down the water inlet hose
1.After using,Close the water tap.
2. Pull off the water inlet hose from the water tap and washer
"Soak" button
Push "soak" button to set soak
procedure.
In standard, carpeting programs,
push "soak" button to set different
soak time (10, 20, 30 minutes)
In fibre programs, push "soak"
button to set soak procedure,
but soaktime can not be changed.
In saving and superfast wool
programs, pushing "soak"
button has no effect.
"Wash" button
Push "wash" button to set wash
procedure.
In standard,carpeting programs,
push "wash" button to set
different wash time (0 6 9
15 20 minutes)
In fibre programs, push "wash"
button to set wash procedure,
but washtime can not be
changed.
In saving and superfast wool
programs, pushing "wash"
button has no effect.
Push this button for 2 seconds or longer,
the sign of "sterilizate "will be lightened.
That mean that function is chosen.
"Rinse/ " buttonSterilize
Push "rinse/sterilize"button to
set rinse procedure.
In standard,carpetingprograms,
push "rinse" button toset
different rinse times (0, 1, 2, 3 )
In fibre programs,push the
"rinse/sterilize"button to set
rinseprocedure, but rinse times
can not be changed.
In saving and superfast wool
programs, pushing "rinse"
buttonhas no effect.
Push this botton for 2 seconds
or longer the sign of Sterilize
will be lightened,that mean the
function is chosen
Push this botton for 2 seconds
again will clear this function ,the
sign will be turued off
"Spin" button
Push "spin" button to set spin
procedure.
In standard, carpeting programs,
push the "spin" buttonto set
different spin time (0 1 3
5 7 minutes).
In fibre programs, push the "spin"
buttonto set spin procedure.
In saving and superfast wool
programs,pushing "spin" button
has no effect.
Page 10
1.Preparation before washing
2.Put in the laundries
Preparation before washing
1.Connect the water inlet hose
2.Confirm that the washing machine is earthed reliably.
Then insert the power plug into the receptacle. Do not
connect the earth terminal to the gas pipe and tap water
pipe.
3.Put up the drain hose
0.8m<H<1.2m
4.Slanting or uneven ground may result in unstable
working or abnormal noise. Please make the
machine stand horizontally.
Pay attention to followings before washing the laundries
Confirm if there's
special requirement
for the laundries.
Clear the pocket.
Take out the coins ,
sand, hairpins etc.
Fasten the buttons
and zippers.
The quantity of the
laundries shall not
exceed the rated
value. The big
laundries like the
jeans shall be put
in loosely.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into
mesh bag for washing.
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put the
laundries with buttons
into other laundries.
The capacity of washing of the machine refer to the largest weight of the
standard laundries under dry condition that can be washed in one time.
Laundries quantity in one washing cycle shall be lower than the rated
capacity.
The thickness ,size , type of the cloth will influence the actual washing capacity.
Do not select " 26" water level for laundries less than 1.0kg ,so as to avoid
splashing of water.
3. Usage of detergent
Softener inlet
Washing powder
inlet
Washing powder box
Control panel seat
Liquid detergent
inlet
Liquid whitener inlet
Add washing powder and softener into
the box directly as per indicated in left figure
After adding, close the box.
How to use washing powder
How to use softener
See to the manual of softener for the usage and dosage.
When adding softener into the softener inlet of washing
powder box, note that it shall not exceed the lower side
of the cap.
Do not leave the softener for long period after adding it
into the box. Otherwise it may be solidified and block the inlet.
As the softener is easy to solidify,please clean the box
frequently.(You shall clean it each time you use reserve
function).
Before use softener, you must select to sterilize function
How to use whitener
Add water to stipulated level. Dilute the whitener with container,
and then pour it into the liquid whitener inlet slowly.
Laundries with color or pattern is not colorfast, thus not applicable.
The whitener shall not touch laundries directly.
See to the manual of whitener for the usage and dosage.
For whitener in powder, dissolve it before use.
It is suggested to add washing powder into the box
directly under fuzzy program and reserve program.
Dissolve directly inside the washing machine: (not
applicable for fuzzy and reserve program)
1.Add some water
2.Add washing powder. Run for about 30s to fully dissolve
the
Powder. Then push the"start/pause" button.
3.Put in laundries. Select suitable water level. Push the
"start/pause"
Quick dissolving of washing powder:
1. Prepare warm water of 30 C and container.
2. Add washing powder while stirring to dissolve it completely.
Please add suitable washing powder as per the laundries
quantity, the set water level and water quantity.
If you select save program, it is suggested to use liquid
detergent instead of washing powder to guarantee the
washing effect.
It is not recommended to use rich-foam washing powder.
Washing powder with poor quality or long-time storage may
get caked. Please clean the detergent box duly in usage.
(select the "14" water level)
button again.
4. Close the top lid
As the top lid opened,the washer will automaticlly givean alam and stop running,exclusively during draining
Loading...